Candy CDF312A User Manual

EN

FR

PT

NL

User instructions Mode d’emploi Instruções de utilização Gebruiksaanwijzing

CDF 312 A

DISHWASHER LAVE-VAISSELLE MÁQUINA DE LAVAR LOIÇA AFWASMACHINE

Congratulations!

Thank you for choosing a Candy appliance; quality dishwashers which guarantee high performance and reliability.

Candy manufacture a vast range of domestic appliances: washing machines, washer/dryers, cookers, microwave ovens, ovens and hobs, refrigerators and freezers.

Ask your dealer for the catalogue with the complete range of Candy products. Please read this booklet carefully as it provides important information regarding the safe installation, use, and maintenance of the machine, together with some useful advice on how to achieve the best results from your dishwasher.

For future reference please keep this instruction booklet in a safe place.

CUSTOMER SERVICE AND GUARANTEE

Your new appliance is fully guaranteed by the manufacturer for 12 months against electrical/mechanical breakdown excluding:

A.Any faults which occur due to bad installation or misuse of the machine.

B.Any faults which occur due to repair of, or interference with, the machine by any person not authorised by the manufacturer to carry out service.

C.Any faults which occur due to any parts which are fitted to the machine which are not the original manufacturers parts.

D.Any faults arising from non-domestic use or unusual or abnormal use of the machine.

E.Any faults arising from operation at incorrect voltage.

F.Any faults arising from incorrect operation of the machine.

The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights.

AFTER SALES SERVICE

For service and repairs call your local engineer on our national telephone number:

	GIAS Service	Tel: [phone]
	Support Service	(Eire 018301 666)
CONTENTS
Description of the controls			pag.		3
Technical data			pag.		3
Operating the programmes and special functions			pag.		4
Programme selection			pag.		6
The Watercontrol system			pag.		8

DESCRIPTION OF THE CONTROL

E F G

A B C D

A "ON/OFF" button	E	"SALT EMPTY" light
B Open door	F	"PROGRAM SELECTION" LEDs
C "PROGRAMS" buttons	G "OPTION SELECTION" LED
D "HALF LOAD" button

DIMENSIONS:

		with working top	without working top
Height			82
	cm	85
Depth	cm	60	57,3
Width	cm	60	59,8
Depth with door open	cm	120	117

TECHNICAL DATA:

EN 50242 place load	12
Capacity with pans and dishes	8 persons
Water supply pressure	Min. 0,08 - Max 0,8 MPa
Fuse	(see rating plate)
Power input	(see rating plate)
Supply voltage	(see rating plate)

2

3

PROGRAM SELECTION AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

Program settings

■Open the door and place dirty dishes inside the appliance.

■Press the "ON/OFF" button .

■After pressing the "ON/OFF" button, the LED for the factory set is "recommended” (which is ideal for full load daily use) or the LED for the "Auto’ Memory" program (see below) will blink.

IMPORTANT

The dishwasher has two very practical functions:

-	the "recommended" program
(	) for quick and sure selection;

- the "Auto’ Memory", function which saves a program used at least 3 times consecutively so that if you regularly use the same washing cycle each time you do not have to continually set the program thereby saving time and effort.

■If you wish to select an option, press the option button (the corresponding LED will light).

The option button must be pressed BEFORE the program starts for the option to be accepted.

■To choose another program, press the corresponding button (the relevant LED will blink to confirm the selection).

IMPORTANT

To select the "COLD RINSE" program, simultaneously press the "RAPID" program button and "HALF LOAD" option button (the relevant LEDs will blink, confirming the selection).

■To start the program, press the selected program button again to confirm. The relevant LED will stop blinking and remain on and, when the door is shut, the program will start automatically.

IMPORTANT

To confirm the “COLD RINSE” program, simultaneously press the “RAPID” program button and the “HALF LOAD” option button (the relevant LEDs will stop blinking and remain on to confirm the selection).

If the previously described operations were performed with the door open, the program will not start until the door is closed.

Program interruption

Opening the door when a program is running is not recommended especially during the main washing and final hot rinse phases. However, if the door is opened while a program is running (for example, to add dishes) the machine stops automatically.

Close the door, without pressing any buttons. The cycle will start from where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before).

IMPORTANT

A running program can be interrupted without opening the door by pressing the "ON/OFF" button. In this case, simply press the "ON/OFF" button again to restart the cycle from where it left off.

Changing a running program

Proceed as follows to change or cancel a running program:

■Hold down the current program button (with the LED on) for at least 3 seconds. The program LEDs (except for the "RAPID" program LED) will blink until all water is drained (if necessary).

The running program will be cancelled and the corresponding LED will start to blink.

IMPORTANT

To cancel the "COLD RINSE" program, simultaneously hold down the "RAPID" program button and "HALF LOAD" option button (the relevant LEDs will blink to confirm cancellation).

■ At this point a new program can be set.

WARNING!

Before starting a new programme, you should check that there is still detergent in the dispenser.

If necessary, top up the dispenser.

If there is any break in the power supply while the dishwasher is operating, a special memory stores the selected programme and, when the power is restored, it continues where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before).

Program end

At the end of the program, the selected cycle LED (2 LEDs for the "COLD RINSE" program) will blink.

Dishes can now be removed and the dishwasher turned off by pressing the "ON/OFF" button or dishes can be loaded for new cycle.

Option button

"HALF LOAD" button

By using this option, it is possible to wash a smaller quantity of crockery: you should load only the upper basket for dishes and place cutlery in the tray in the bottom basket.

This reduces water and energy consumption and requires a smaller quantity of detergent.

IMPORTANT

This button MUST be set BEFORE the program starts.

Fault signals

If malfunctions or faults occur when a program is running the LED that corresponds to the selected cycle (2 LEDs for the "COLD RINSE" program) will blink rapidly.

In this case, turn the dishwasher off by pressing the "ON/OFF" button. After checking to make sure the water intel hose tap is open, that the drain hose is not bent and that the siphon or filters are not clogged, set the selected program again. If the anomaly persists, contact Customer Service.

IMPORTANT

This dishwasher is equipped with an anti-overflow safety device which will automatically empty any excess water should a problem occur.

WARNING!

To ensure the correct operation of the anti-overflow safety device, it is recommended not to move or to tilt the dishwasher during operation.

If it is necessary to move or to tilt the dishwasher, first make sure the washing cycle is finished and that no water is left in the tank.

4	5

PROGRAMME SELECTION

Programme	Description

	UNIVERSAL	(“RECOMMENDED” PROGRAMME)
		Once a day - for normal soiled pans and any
		other items that have been left all day for
		washing.
	HYGIENIC	Once a day - for heavily soiled pans and any
		other items that have been left all day for
		washing.
	ECO	Energy Saving Programme suitable for
		normal soiled items. Using detergents with
		enzyme.
		Programme standardised to EN 50242.
	RAPID 32’	Quick wash for dishes which are to be
		washed immediately after the meal. Wash
		load of 4/6 persons.
	COLD RINSE	Short cold pre-wash for items that are stored
	+	in the dishwasher until you are ready to
		wash a full load.

Wash with prewash

If setting the HYGIENIC wash programme, a second dose of about 20 g of detergent (1 table-spoon) must be added directly in the machine.

Check list

Programme contents

Avarage

Special function

duration

buttons

in minutes

available

Detergent for soaking (Prewash)

Detergent for washing

Clean filter

Check rinse aid dispenser

Check salt container

Hot pre-wash

Cold pre-wash

Main wash

First cold rinse

Second cold rinse

Hot rinse with rinse aid

Withcold water (15°C) -Tolerance ± 10%-

"HALF LOAD" button

•

•

•

•••

65°C

••

••

95

YES

•

•

•

•

•

75°C

••

••

••

120

YES

•

•

•

•

••

••

•

45°C

140

YES

•

• ••

50°C

••

32

•

••

5

6

7

WATERCONTROL-SYSTEM

The water-stop device protects against water damages caused by leaks on the fill hose which could develop due to natural ageing of the hose.

In the water-stop system the leaking water fills the corrugated hose and activates a stop valve which cuts off the water supply to the machine.

This fault is shown by a red sector on the window « A». Would this occur, please refer to your Service Agent.

If the hose is not long enough for correct connection, it must be replaced with a longer one. The hose can be obtained from your Service Agent.

Safety antitwist device (press and twist to remove the washer)

A

Red button blocked valve indicator

Compliments,

en ayant acheté un appareil électroménager Candy, vous avez fait preuve d’une très grande éxigence: vous voulez le meilleur.

Candy est heureux de vous proposer cette nouvelle machine, fruit d’années de recherches et d’expériences confirmées sur le marché. Vous avez choisi la qualité, la fiabilité et les prestations techniques élevées.

Candy vous propose de plus, une gamme complète d’appareils d’électroménagers: machines-à-laver, lave-vaisselle, machines-à-laver séchantes, séche-linge, four à micro-ondes, fours et plaques de cuisson, réfrigérateurs et congélateurs. Demandez à votre Revendeur le catalogue complet des produits Candy. Nous vous prions de lire attentivement les indications contenues dans ce mode d’emploi. Vous y trouverez d’importantes indications, sur la sécurité d’installation, d’emploi, de manutention et d’autres conseils utiles pour le meilleur emploi du lave-vaisselle.

Conservez avec soin ce mode d’emploi pour des consultations futures.

GARANTIE

Cette machine est livrée avec un certificat de garantie qui permet de contacter gratuitement l’assistance technique.

Veuillez garder votre ticket d’achat et le mettre dans un endroit sûr en cas de besoin.

INDICE

Description de la machine	pag. 10
Données techniques	pag. 10
Sélection des programmes
et fonctions spéciales	pag. 11
Watercontrol	pag. 13
Liste des programmes	pag. 14

8

9

DESCRIPTION DE LA MACHINE

E F G

	A					B	C	D
A Touche "MARCHE/ARRÊT"
					E Témoin de "MANQUE DE SEL"
B Ouverture porte					F Voyants "SÉLECTION DE PROGRAMME"
C Touches "PROGRAMMES"					G Voyant "SÉLECTION D’OPTION"
D Touche "DEMI-CHARGE"
	DIMENSIONS:
					avec plan de travail			sans plan de travail
	Hauteur							82
			cm			85
	Profondeur		cm			60		57,3
	Largeur		cm			60		59,8
	Encombrement porte ouverte		cm			120		117
	DONNÉES TECHNIQUES:
	Couvert (EN 50242)						12
	Capacité avec casseroles et assiettes						8 personnes
	Pression admise pour l'installation hydraulique						Min. 0,08 - Max 0,8 MPa
	Fusible						(voir plaque signalétique)
	Puissance maximum absorbée						(voir plaque signalétique)
	Tension						(voir plaque signalétique)
					10

SELECTION DES PROGRAMMES ET FONCTIONS SPÉCIALES

Choix des programmes

■Ouvrez la porte et rangez la vaisselle à laver.

■Appuyez sur la touche "MARCHE/ARRÊT " .

■Lorsque vous enfoncez la touche "MARCHE/ARRÊT ", le voyant correspondant au programme "conseillé" (pré-confi- guré en usine et parfait pour l’utilisation quotidienne à pleine charge), ou celui correspondant à un programme utilisé au moins 3 fois de suite, clignote.

IMPORTANT

Le lave-vaisselle dispose de deux fonctions très utiles :

-le programme "conseillé" ( ) permettant d’effectuer une sélection plus rapide et sûre ;

-la fonction "auto-apprentissage" permet de proposer le programme utilisé au moins 3 fois de suite et procure ainsi un gain de temps en évitant de répéter chaque fois la même programmation.

■Vous pouvez aussi appuyer sur la touche Option (le voyant correspondant s’éclaire).

Vous devez appuyer sur la touche Option AVANT le démarrage du programme pour que l’option soit acceptée.

■Pour choisir un autre programme, appuyez sur la touche correspondant au programme voulu (le voyant correspondant clignote pour confirmer la sélection effectuée).

IMPORTANT

Pour sélectionner le programme "TREMPAGE" appuyez en même temps sur la touche du programme "RAPIDE" et sur celle de l’option "DEMI-CHARGE" (les voyants correspondants clignotent pour confirmer la sélection effectuée).

11

■Pour lancer le programme vous devez le confirmer en appuyant encore sur la touche du programme choisi.

Le voyant correspondant cesse de

clignoter et s’éclaire fixement et, la porte étant fermée, le programme démarre automatiquement.

IMPORTANT

Pour confirmer le programme "TREMPAGE" appuyez en même temps sur la touche du programme "RAPIDE" et sur celle de l’option "DEMI-CHARGE" (les voyants correspondants cessent de clignoter et s’éclairent fixement pour confirmer la sélection effectuée).

Si vous effectuez les opérations qui précèdent avec la porte ouverte, le programme ne démarrera pas tant que vous ne fermerez pas la porte.

Interruption du programme

Nous vous déconseillons d’ouvrir la porte pendant l’exécution du programme, surtout pendant la phase centrale du lavage et celle du rinçage chaud final.

Cependant, si vous ouvrez la porte lorsque le programme est en cours (par exemple pour ajouter de la vaisselle), la machine s’arrête automatiquement.

Lorsque vous refermez la porte, le cycle repart de l’endroit où il s’était interrompu (en effectuant au besoin un court programme antichoc thermique) sans devoir appuyer sur une touche.

IMPORTANT

Vous pouvez interrompre le programme en cours même sans ouvrir la porte, en appuyant sur la touche "MARCHE/ARRÊT". Dans ce cas, pour que le cycle redémarre de l’endroit où il s’est interrompu, il suffit d’appuyer à nouveau sur la touche "MARCHE/ARRÊT".