Camp Chef smokepro PG24SG, smokepro PG24SGB, smokepro PG24SGS Warning & Instruction Booklet

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

PELLET GRILL AND SMOKER

WARNING & INSTRUCTION BOOKLET

MODEL NUMBER: PG24SG, PG24SGB, PG24SGS

WARNING

FOR OUTDOOR USE ONLY

WARNING

If the information in this manual is not followed exactly, a ﬁre or explosion may result causing property damage, personal injury or loss of life.

WARNING

• To installer or person assembling this appliance: Leave this manual with this appliance for future reference.

• To consumer: Keep this manual with this appliance for future reference.

This instruction manual contains important information necessary for the proper assembly and safe use of this product. Read and follow all warnings and instructions before assembling and using this appliance. Do not discard this instruction manual.

CAUTION

Use Only Wood Pellet Fuel Speciﬁed By The Manufacturer. Do Not Use Pellet Fuel Labeled As Having Additives. Only use Camp Chef Premium Pellets with the following speciﬁcations. 8,0008,300 BTU/LB 0.75-0.85% Ash content

CAUTION

Contact local building or ﬁre ofﬁcials about restrictions and installation inspection requirements in your area.

A MAJOR CAUSE OF FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS PRODUCT BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

DANGER

1. Never operate this appliance unattended.

2. Never operate this appliance within 10 ft (3 m) of any structure, combustible material or other gas cylinder.

3. Never operate this appliance within 25 ft (7.5 m) of any ﬂammable liquid.

4. If a ﬁre should occur, keep away from appliance and immediately call your ﬁre department. Do not attempt to extinguish an oil or grease ﬁre with water.

Failure to follow these instructions could result in fire, explosion or burn hazard, which could cause property damage, personal injury or death.

CAUTION

Always store wood pellets away from heat producing appliances and other food containers. Pellets should be stored in a dry environment.

PG24SG

0817 PG24SG

PARTS

CHIMNEY CAP ASM (1) PG24-5

CHIMNEY (1) PG24-6

LOWER GRATE (2) PG24-70

THERMOMETER (1)

PG24-44

PROBE COVER (1)

PG24-54

FEED GASKET (1)

PG24-34

ASH CUP (1)

PG24-17

GREASE BUCKET (1) PG24-11

M8 LOCK WASHER (8)

M8 X 20 BOLT (8)

BURNER PULLOUT (1) PG24-41

PULLOUT LOCK (1) PG24-42

PULLOUT KNOB (2) PG24-9

SHELF (1) PG24-8 (BLACK) PG24-8B (BRONZE) OPTIONAL

M6 HANDLE SCREW (2) PG24-59

HANDLE DEFLECTOR (1) PG24SG-12

WHEEL (2) PG24-16

AXLE BOLT (2) PG24XT-3

RIGHT LEG (2) PG24XT-2

AXLE (1)

PG24XT-4

LEFT LEG (2)

PG24XT-1

HANDLE BEZEL (2) PG24-71

HANDLE (1) PG24-57

M6 X 76 BOLT (1)

M6 NUT (2)

CHIMNEY GASKET (1) PG24-7

M6 X 15 BOLT (2)

M6 FLAT WASHER (2)

M6 LOCK WASHER (2)

M6 NUT (2)

M8 NUT (2)

UPPER GRATE (2) PG24SG-5

DRIP TRAY (1) PG24SG-4

SLIDE ROD (2) PG24SG-1

HEAT DEFLECTOR (1) PG24SG-2

PULL ROD (1)

PG24SG-3

LID

PG24SG-6 ( BLACK)

PG24SG-6B (BRONZE)

PG24SG-6S (STAINLESS)

HOPPER ASM (1)

PG24SG-9 (BLACK)

PG24SG-9B (BRONZE)

M6 X 15 BOLT (9)

M6 KEEPSNUT (4)

BOTTOM SHELF (1)

PG24XT-5

UPPER GRATE BRACKET (2) PG24SG-11

CARBON MONOXIDE WARNING

Follow these guidelines to prevent this colorless, odorless gas from poisoning you, your family or others. Know the symptoms of carbon monoxide poisoning: headache, dizziness, weakness, nausea, vomiting, sleepiness, and confusion. Carbon monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in loss of consciousness and death. See a doctor if you or others develop cold or ﬂu-like symptoms while cooking or in the vicinity of this appliance. Carbon monoxide poisoning, which can easily be mistaken for a cold or ﬂu, is often detected too late. Alcohol consumption and drug use increase the effects of carbon monoxide poisoning. Carbon monoxide is especially toxic to mother and child during pregnancy, infants, the elderly, smokers and people with blood or circulatory system problems, such as anemia, or heart disease.

0817 PG24SG PARTS

HOPPER RAKE (1)

PG24-52

HOPPER LID (1)

PG24-60 (BLACK)

4B-

(

NZE

)

PTI

AUGER GUARD (1)

PG24-53

LID MAGNET (1)

PGC24-18

POWER CORD (1)

PG24-48

PULLOUT KNOB (1)

PG24-9

M6 X 15 BOLT (2)

PULLOUT LOCK (1)

PG24-42

HOPPER CLEANOUT (1)

PG24-13

M6 NUT (2)

CONTROLLER GASKET (1)

PG24-45

GUARD PLATE (1)

PG24-46

MEAT PROBE (2)

PG24-28

CONTROLLER (1)

PG24SG-10

CONTROLLER KNOB (1)

PG24-30

M4.2 X 10 SCREW (2)

AUGER BUSHING (1)

PG24-23

AUGER PIN W/NUT (1)

PG24-25

M4.2 X 10 SCREW (4)

BLOWER IMPELLER (1)

PG24-27

BLOWER MOTOR WITH IMPELLER (1)

PG24-26

M4.2 X 10 SCREW (4)

BURNER (1)

PG24-20

HEATING ROD (1)

PG24-21

AUGER (1)

PG24-22

AUGER MOTOR WITH IMPELLER (1)

PG24-24

AUGER IMPELLER (1)

PG24-49

M6 X 15 SCREW (2)

M6 NUT (2)

M6 LOCK WASHER

M6 FLAT WASHER (2)

HOPPER HANDLE

(1) PGC24-12

on the ambient temperature as well as cooking temperature.

16. It is recommended that you not store pellets in the hopper for extended periods as they may absorb moisture from the air and clog the auger.

17. Keep the lid closed during cooking. The grill is designed to cook with the lid closed.

18. Note that the cooking temperature displayed on the digital readout is measured near the cooking surface on the left side of the grill. The actual temperature inside the cooking chamber will vary slightly throughout.

19. Do not use accessories not specified for use with appliance.

20. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or freshen up a fire in this appliance. Keep all such liquids well away from the appliance when in use.

21. Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a non combustible floor or on the ground, well away from all combustible materials, pending final disposal. When the ashes are disposed by burial in soil or otherwise locally dispersed they should be retained in the closed container until all cinders have thoroughly cooled.

22. Creosote – Formation and need for removal. When wood pellets are burned slowly, they produce tar and other organic vapors that combine with expelled moisture to form creosote. The creosote vapors condense in a relatively cool oven flue and exhaust hood of a slow burning fire. As a result, creosote residue accumulates on the flue lining and exhaust hood. When ignited, this creosote makes an extremely hot fire. The grease duct should be inspected at least twice a year to determine when grease and/or creosote buildup has occurred. When grease or creosote has accumulated, it should be removed to reduce risk of fire.

DANGER

Do not work on this grill if it is plugged in. Electric shock may occur resulting in death or serious injury.

1. Do NOT leave this appliance unattended while in use. The user must remain in the immediate area of the product and have a clear view of the product at all times during operation.

2. Keep children and pets away from burner at all times.

3. The use of alcohol, prescription or nonprescription drugs may impair your ability to properly assemble or safely operate this appliance.

4. For OUTDOOR use only. Do NOT use in a building, garage or any other enclosed area. Do NOT use in or on recreational vehicles or boats. NEVER use this appliance as a heater.

5. Do not operate appliance under ANY overhead construction. Keep a minimum clearance of 18 inches (0.5 m) from the sides, front and back of appliance to ANY construction. Keep the area clear of all combustible material and flammable liquids, including wood, dry plants and grass, brush, paper, and canvas.

6. This product is not intended for commercial use.

7. Always allow the appliance to cool before covering with the patio cover.

8. Always cover the appliance, with patio cover (if supplied), when not in use.

9. Always unplug grill before installing patio cover.

10. Use only on a level, stable non-combustible

surface like bricks, concrete or dirt. Do not use this appliance on any surface that will burn or melt like wood, asphalt, vinyl or plastic.

11. Make sure burner clean-out is closed before

starting the grill.

12. Make sure the grease bucket is in place before

starting the grill.

13. In the event of a fire the dial should be turned

to shutdown, close the lid, and leave it closed until the fire goes out. After allowing the grill to cool, follow the cleaning instructions before the next use.

14. Use only food grade hardwood pellets

manufactured for use in pellet grills. Using softwood or heating pellets will void your warranty.

15. Do not allow the hopper to run out of pellets.

Pellets can be added at any time. The hopper will hold approximately 15 pounds of pellets. The pellet usage will vary greatly depending

ATTACH CHIMNEY AND CHIMNEY CAP

1. Install chimney to grill as shown in Fig 4. Make sure to install the gasket between the grill and the chimney.

2. Tighten all hardware.

3. Install M6 x 76 Bolt through chimney cap and secure using Qty (1) M6 nut. Thread second nut onto bolt leaving approximately 1.5” to the top of the cap. Thread cap assembly down into the chimney bracket until the lower nut hits the bracket. See Fig 4.

FIG. 4

M6 X 76 BOL

M6 NUT

M6 X 15 SCREW

CHIMNEY GASKET

M6 FLAT WASHER

M6 LOCK WASHER

M6 NUT

4. The height of the chimney cap can be adjusted for summer and winter. In the summer the gap should be approximately 1-1/2”. In the winter the gap should be approximately ½”.

5. Tighten all hardware.

INSTALL HANDLE

1. Install the handle as shown in Fig 5.

2. Tighten all hardware.

FIG. 5

PG24 HANDLE

PG HANDLE BEZEL

HANDLE HEAT DEFLECTOR

HANDLE SCREW

INSTALL SHELF BRACKET

1. Install the bracket as shown in Fig 6.

2. Tighten all hardware.

M6 X 10 SCREW (4)

M6 FLANGE NUT (4)

UPPER GRATE BKT (2) PG24SG-11

FIG. 6

ASSEMBLY INSTRUCTIONS

Remove all loose parts from the inside of the grill and hopper. Lay a blanket or piece of cardboard down to protect the grill.

ATTACH THE LEGS

With the help of another person ﬂip the grill upside down on the blanket or cardboard. The grill lid and hopper lid will swing open when doing this so be careful not to damage the lids. The grill may also want to roll on its lid so one person should hold the grill steady while the other person assembles the bottom legs and wheels.

1. Assemble the legs as shown in Fig. 1. Finger tighten hardware.

FIG.1

M8 X 20 BOLT (8)

M8 LOCK WASHER (8)

2. Install bottom shelf as shown in Fig.2

M6 X 15 SCREW (4)

M6 FLANGE NUT(4)

FIG. 2

3. Assemble wheels to the legs as shown in Fig.3.

FIG. 3

WHEEL AXLE (2)

WHEEL (2)

AXLE (1)

4. With the help of another person, stand the grill upright. Be careful as the lid on the hopper and grill will close as the grill is stood upright.

5. Tighten all hardware assembled in the previous steps.

GREASE BUCKET

1. Hang grease bucket from tube as shown in Fig 7.

ASH CUP

1. Install Ash Cup as shown in Fig 7. Never use grill without Ash Cup in place.

ASH CUP

GREASE BUCKET

FIG. 7

INSTALL DRIP TRAY

1. Install the Drip Tray as shown in Fig 8 and Fig 9.

FIG. 8

DRIP TRAY

FIG. 9

WARMING RACK AND COOKING GRATE

1. Install the cooking grate as shown in Fig 10.

UPPER GRATE (2) PG24SG-5

LOWER GRATE (2) PG24-70

FIG. 10

CLEAN-OUT PORT KNOB

1. Clean-out Port knob must be pushed in when grill is on. Make sure pullout lock is pushed down and locks the knob to prevent inadvertent opening of the clean-out port. See Fig 11.

2. Lift pullout lock and pull clean-out port knob to empty ash into ash cup. See Fig 12

3. See instructions for burner clean-out.

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

FIG. 11

CLEANOUT PORT OPEN

FIG. 12

BURNER CLEAN-OUT

Before each use the burner should be cleaned out by lifting the pullout lock and pulling the clean-out port knob on the right side of the grill to open the burner clean-out. This will allow the ash from previous use to fall into the cup under the grill. The cup should be removed and emptied and then reinstalled before each use.

DANGER

Never Operate the Pellet grill without the ash cup in place. Make sure the burner clean-out port is closed and locked before starting the grill.

WARMING RACK

COOKING GRATE

CLEANOUT PORT KNOB

Never open the burner clean-out port when the

grill is hot. After cleaning out the burner make sure to close the burner clean-out by pushing the clean-out port knob in on the right side of the grill. Make sure to lift the pullout lock and push the clean-out port knob all the way in and lock in place with the pullout lock. Every 50 hours of use, remove the grill grates, grease tray, and heat deﬂector and clean the inside of the grill. If you notice a lot of ash blowing around in the grill it is time to vacuum it out.

FILLING THE AUGER TUBE CAUTION: ONLY USE THE FEED SETTING WHEN HOPPER HAS RUN OUT OF PELLETS. FEED SETTING IS NOT FOR NORMAL USE.

The ﬁrst time you use your grill or any time the hopper has ran out of pellets you will need to ﬁll the auger tube. This simply means you must ﬁll the auger tube with pellets until pellets reach the burner. This is done by turning the dial to the FEED position and then holding in the bypass button for 3 seconds. This will turn the auger on and the digital readout will display “FEED”. The auger will remain on for no more than 7 minutes. This is ample time for the pellets to reach the burner. It is easiest to open the burner clean-out by pulling the knob on the right side of the grill. Once you hear pellets dropping into the cup you can close the clean-out port by pushing the knob on the right side of the grill and then select your cooking temperature. (Never operate grill without the ash cup in place). Always make sure the burner clean-out port is closed by pushing in the knob on the right side of the grill before selecting any of the cook settings. Never open the burner clean-out port when the grill is hot.

CONTROLLER EXPLANATION POWER SWITCH

Used to turn the main power onto the pellet grill. If the dial is on Shutdown when the power switch is turned on the digital readout will display “---

--“. The dial must be rotated to any of the other positions before the grill will start. If the power is turned on with the dial in any other position than Shutdown the grill will immediately start that function. “O” is Off. “-“ is On. See Fig. 13

Fig. 13

DIAL POSITIONS SHUTDOWN

This setting must be used after each use. Turn the dial to this setting and the fan will remain on for 10 minutes before turning off. This setting will

burn up any extra pellets in the burner and cool down the grill. Do not turn the main power switch off when the grill is hot. FEED - This setting is used to feed pellets to the burner. It will be used the ﬁrst time you use the grill to ﬁll the auger tube and any time you may inadvertently run the hopper out of pellets. See instructions on ﬁlling the auger tube. LOW SMOKE - This setting is used for smoking foods at an average temperature of 160F. This setting will produce large amounts of smoke. HIGH SMOKE - This setting is used for smoking foods at an average temperature of 220F. This setting will produce large amounts of smoke. 175F TO 400F - There are 25F increment settings from 175F to 400F. You can simply select any temperature you want and the grill will control the temperature within 15F of the selected temperature. HIGH - This setting can be used to achieve temperatures up to 500F depending on ambient temperatures.

DISPLAY

“START” - The digital readout will display “START” each time the dial is changed from the OFF, SHUTDOWN, or FEED settings to any of the cook settings. The startup cycle is approximately 8 minutes. During the cook cycle after the start sequence the digital readout will display the temperature inside of the grill. If the Probe Temp button has been pressed then it will display the temperature of the external probe used for measuring meat temperatures. “SDOWN” - The digital readout will display “SDOWN” when the dial is turned to the shutdown mode. After 10 minutes the digital readout and the fan will turn off. “SENSR” - The digital readout will display “SENSR” if there is an error with the temperature sensor inside of the grill. “PRERR” - The digital readout will display “PRERR” when the Probe Temp button is pressed if either the external probe is not plugged in or there is a problem with the probe. “FEED” - The digital readout will display “FEED” if dial is turned to the feed mode. After 7 minutes the auger will turn off. “BPASS” - The digital readout will display “BPASS”

when the bypass button is pressed and held in for 3 seconds. See the setting on Bypass Mode. “FLAME” - The digital readout will display “FLAME” if the ﬁre is extinguished.

BREAKING IN THE GRILL

We suggest turning the grill to 350F for ½ hour before cooking on the grill for the ﬁrst time. This will burn off any manufacturing oils and cure the paint. Make sure to follow the instructions for ﬁlling the auger tube before breaking in the grill.

WARNING

Always start the grill with the lid open. The lid must be closed after the start cycle.

COOKING

Once the auger tube has been properly ﬁlled you can begin cooking by selecting any of the cooking temperatures. The grill has 13 cook settings. Low Smoke, High Smoke, 175, 200, 225, 250, 275, 300, 325, 350, 375, 400, and High. By selecting any of these the grill will go into the Startup mode. The digital readout will display “START” for 8 minutes during the startup cycle. After the 8 minutes the digital readout will display the internal temperature of the grill. The dial can be changed at any time during the startup cycle or the cook cycle between any of the 13 cook settings.

WARNING

Do not over-ﬁre the grill by over feeding pellets into the burner prior to startup. If ﬂame is inadvertently extinguished never restart the grill without ﬁrst cleaning out the burner. Improper use can cause an uncontrolled ﬁre.

DIRECT FLAME MODE

Pull grill knob out all the way to allow direct heat as shown in Fig 14. Best for burgers and steaks.

Fig. 14

INDIRECT FLAME MODE

Push grill knob in all the way for indirect heat as shown in ﬁg 15. Best for chicken, slow smoking

and low temps.

Fig. 15

WARNING

Always clean grease tray to remove excess

grease drippings prior to cooking in Direct

Flame Mode. A dirty grease tray may result in

excessive ﬂare ups or uncontrolled ﬁre.

SHUTDOWN

When you are done cooking the dial must be turned to the Shutdown setting. The digital readout will display “SDOWN”. In this setting the fan will remain on for 10 minutes to ﬁnish burning any pellets in the burner and cool the grill down. After 10 minutes the digital readout and auger will turn off. At this point the main power switch should be switched to off. Before grill can be used, the power switch must be turned off and back on.

BYPASS MODE

The bypass may be used if there is a power failure, or the grill is accidentally turned off, or anytime you need to restart the grill and it is still hot. The bypass mode should only be used if the grill has been off less than 3-4 minutes. This method is used to bypass the normal startup mode and get the grill cooking again quickly. The burner must still be hot enough to ignite new pellets or this method will not work. In order to initiate the bypass mode you must ﬁrst select the cook setting you want. At this point the digital readout will display “START”. Simply press the bypass button in and hold it for 3 seconds. The digital readout will display “BPASS”. Release the button and the grill will go into the cook mode and the digital readout will display the grill temperature. If the grill fails to ignite using the bypass mode then restart the grill using the normal startup procedures.

Meat Probes

This smoker has built in meat probes to measure the temperature of the food as it is being cooked. To use these probes insert the wire through the

+ 19 hidden pages

Camp Chef smokepro PG24SG, smokepro PG24SGB, smokepro PG24SGS Warning & Instruction Booklet

Specifications and Main Features

Frequently Asked Questions

User Manual