Cameo FLAT PRO CLPFLATPRO7IP65, FLAT PRO CLPFLATPRO12IP65, FLAT PRO CLPFLATPRO18IP65 User Manual

FLAT PRO OUTDOOR PAR CAN

7 X 10W LED RGBWA PAR CAN CLPFLATPRO7IP65 12 X 10W LED RGBWA PAR CAN CLPFLATPRO12IP65 18 X 10W LED RGBWA PAR CAN CLPFLATPRO18IP65

USER´S MANUAL BEDIENUNGSANLEITUNG MANUEL D´UTILISATION MANUAL DE USUARIO INSTRUKCJA OBSŁUGI MANUALE D‘USO

Introduction

Classiﬁed according to EN 60529 as a device of protection category IP65, professional PAR projectors from the Cameo FLAT PRO OUTDOOR series deliver vivid colours for use in outdoor areas. The extremely compact housing is perfectly suited for environments with limited space, whereby the passive cooling concept ensures 100% silent operation. With their 10 watt high performance RGBWA LEDs, the projectors allow versatile colour blends from soft pastels to rich, warm colours, which are emitted with an impressive brightness at a beam angle of 30°. In addition, the 3000 Hz refresh rate guarantees absolutely ﬂicker-free operation.

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

Thank you for choosing Cameo Lights!

We have designed this product to give you reliable operation over many years.

Please, take a few moments to read these instructions carefully, as we want you to enjoy your new Cameo Lights products quickly and to the fullest.

Further information about Cameo Lights check our website WWW.CAMEOLIGHT.COM

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

FLAT PRO OUTDOOR PAR CAN

7 X 10W LED RGBWA PAR CAN CLPFLATPRO7IP65 12 X 10W LED RGBWA PAR CAN CLPFLATPRO12IP65 18 X 10W LED RGBWA PAR CAN CLPFLATPRO18IP65

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

PREVENTIVE MEASURES:

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufﬁciently stable and compatible stands and/or mounts (for ﬁxed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observ e the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed so that is cooled sufﬁciently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment in this case, observe the special instructions noted below. Do not expose this equipment to ﬂammable materials, ﬂuids or gases.

12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers ﬁlled with liquids, such as vases or drinking vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.

17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.

18. If your equipment is no longer functioning properly, if ﬂuids or objects have gotten inside the equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualiﬁed personnel.

19. Clean the equipment using a dry cloth.

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:

22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

23. If the equipment has been exposed to strong ﬂuctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

24. Before connecting the equipment to the power outlet, ﬁrst verify that the mains voltage and frequency match the values speciﬁed on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not ﬁt in your wall outlet, contact your electrician.

25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter and the equipment connector.

26. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

SAFETY:

to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment.

28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised service centre.

29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.

30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.

31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable parts inside. Have repairs carried out only by qualiﬁed service personnel.

The lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electrical shock.

The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions.

CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS

1. Do not look into the beam from a distance of less than 40 cm.

2. Do not stare into the beam for extended periods at short-to-medium distances.

3. Do not view the beam directly with optical instruments such as magniﬁers.

4. Under some circumstances, stroboscopic effects may trigger epileptic seizures in sensitive individuals! For this reason, persons who suffer from epilepsy should always avoid places where strobe lights are used.

The product has been developed for professional use in the ﬁeld of event technology and is not suitable as household lighting.

INTRODUCTION:

7 x 10 W 5-in-1 LED RGBWA FLAT PAR OUTDOOR PROJECTOR

CLPFLATPRO7IP65

CONTROL FUNCTIONS:

• 2-channel, 3-channel 1, 3-channel 2, 5-channel and 8-channel DMX control

• Red, green, blue, white and amber controllable separately

FEATURES:

• Jet-proof according to EN 60529

• 7 X 10 W 5-in-1 LEDs

• RGB colour spectrum + white + amber

• 30° beam angle

• Refresh rate 3000 Hz

• Silent operation thanks to convection cooling

• Power consumption 40 W

• Operating voltage 110 V - 240 V AC

• Special IP65 connector for the power supply

• Special IP65 connector for DMX In and Out

• Lit multifunctional LC display

• Adjustable multi-functional mounting bracket

• Master/slave mode

• Colour change rate and stroboscope effect controllable via control panel and DMX

12 x 10 W 5-in-1 LED RGBWA FLAT PAR OUTDOOR PROJECTOR

CLPFLATPRO12IP65

CONTROL FUNCTIONS:

• 2-channel, 3-channel 1, 3-channel 2, 5-channel and 8-channel DMX control

• Red, green, blue, white and amber controllable separately

FEATURES:

• Jet-proof according to EN 60529

• 12 X 10 W 5-in-1 LEDs

• RGB colour spectrum + white + amber

• 30° beam angle

• Refresh rate 3000 Hz

• Silent operation thanks to convection cooling

• Power consumption 95 W

• Operating voltage 110 V - 240 V AC

• Special IP65 connector for the power supply

• Special IP65 connector for DMX In and Out

• Lit multifunctional LC display

• Adjustable multi-functional mounting bracket

• Master/slave mode

• Colour change rate and stroboscope effect controllable via control panel and DMX

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

INTRODUCTION:

18 x 10 W 5-in-1 LED RGBWA FLAT PAR OUTDOOR PROJECTOR

CLPFLATPRO18IP65

CONTROL FUNCTIONS:

• 2-channel, 3-channel 1, 3-channel 2, 5-channel and 8-channel DMX control

• Red, green, blue, white and amber controllable separately

FEATURES:

• Jet-proof according to EN 60529

• 18 X 10 W 5-in-1 LEDs

• RGB colour spectrum + white + amber

• 30° beam angle

• Refresh rate 3000 Hz

• Silent operation thanks to convection cooling

• Power consumption 125 W

• Operating voltage 110 V - 240 V AC

• Special IP65 connector for the power supply

• Special IP65 connector for DMX In and Out

• Lit multifunctional LC display

• Adjustable multi-functional mounting bracket

• Master/slave mode

• Colour change rate and stroboscope effect controllable via control panel and DMX

OPERATION:

The Cameo FLAT PRO OUTDOOR projectors are DMX-512 controllable, and are characterised by highly efficient, bright LEDs. The intensity of the five colour groups (red, green, blue, white, amber) can be controlled independently of one another, thus permitting an unlimited number of different colours. The Cameo LED projectors can can be used both individually and in master/slave mode, with music control, and via DMX-512 protocol. The integrated stand/bracket offers a secure hold when using the projector as a free-standing unit, or for assembly on trusses.

NOTE: Overhead installation may only be carried out by trained personnel. The projector must be secured with an appropriate safety cable to prevent falling.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

CONNECTIONS, CONTROLS AND INDICATORS:

Figure CLPFLATPRO12IP65

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

6 7

CONNECTIONS, CONTROLS AND INDICATORS:

POWER IN

Permanently attached power cord with special screw-down cable plug (dust- and jet-proof according to IP65). Power cord with Schuko plug included.

POWER OUT

Permanently attached power cord with special screw-down cable plug (dust- and jet-proof according to IP65) for powering additional CAMEO outdoor projectors (screw-on cap included). Make sure that the total current consumption in amperes (A) of all connected devices does not exceed the speciﬁed value on the device. It can be connected directly to an additional CAMEO outdoor projector of the same type. Matching power cords in various lengths are available as accessories. When operating a single outdoor projector , the POWER OUT cable must be closed securely by the cap. The same applies for outdoor projectors that are located at the end of a chain of lights.

DMX IN

Permanently attached DMX cable with screw-down special cable plug (dust- and jet-proof according to IP65) for connecting a DMX controller (e.g., DMX mixer). Screw-down cap and DMX connecting cable with male 3-pole XLR plug included.

DMX OUT

Permanently attached DMX cable with screw-down special cable plug (dust- and jet-proof according to IP65) for looping through the DMX control signal. Screw-down cap included. It can be connected directly to an additional CAMEO outdoor projector of the same type. Matching DMX cables in various lengths are available as accessories. When operating a single outdoor projector, the DMX OUT cable must be closed securely by the cap. The same applies for outdoor projectors that are located at the end of a chain of lights.

MODE

Selection of the standalone functions, DMX modes, and DMX address.

ENTER

Makes it possible to change a value and conﬁrm changes.

UP AND DOWN BUTTONS

Press the UP and DOWN buttons, for example, to change the stroboscope speed or DMX address.

LIT LC DISPLAY

Displays the operating mode and values of individual functions.

NOTE

: An extensive selection of suitable IP65 DMX extension cables, IP65 power extension cables and adapter

cables, is available on the Internet at www.cameolight.com.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

OPERATION:

NOTE:

When the projector is properly connected to the mains, the following information appears successively in the display during the startup process: "Software Update, Please Wait..." (for service purposes only), the software version "Software V1.xx" and "WELCOME TO cameo". After this operation, the projector is ready for use and changes back to the mode that was previously selected.

STATIC COLOUR

This mode offers the ability to separately adjust the intensity for each of the 5 LED groups and to generate an unlimited number of different colours (colour mixing). Press the MODE button until "STATIC" appears in the upper line of the display. By repeatedly pressing the ENTER button, select the LED group for which you want to change the brightness level (please note the cursor in the display, Rxx = red, Gxx = green, Bxx = blue, Wxx = white, Axx = amber). Now you can set the intensity of the selected light from 00 to 99 using the UP and DOWN buttons (example: R00 = red at 0%, i.e. out. R99 = red at 100%, i.e. maximum brightness). Adjust the ﬂash frequency of the strobe effect by pressing ENTER repeatedly until the cursor shows "Fxx". Now you can activate the strobe effect using the UP and DOWN buttons and set the ﬂash frequency from 00 to 99 (F00 = strobe effect deactivated, F01 = approx. 1 Hz, F99 = approx. 20 Hz). Conﬁrm with ENTER.

RED Intensity R00 - R99

GREEN Intensity G00 - G99

BLUE Intensity B00 - B99

WHITE Intensity W00 - W99

AMBER Intensity A00 - A99

STROBOSCOPE Speed F00 - F99

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

OPERATION:

COLOUR MACROS

In this mode, one of the 5 basic colours of the projector or one of the 10 different mixed colours can be selected as a preset. Press the MODE button until "MACRO" appears in the upper line of the display. Now press ENTER and then select one of the 15 colour presets using the UP and DOWN buttons. Conﬁrm with ENTER.

MACRO 01 = red MACRO 09 = pink MACRO 02 = green MACRO 10 = light green MACRO 03 = blue MACRO 11 = magenta MACRO 04 = white MACRO 12 = turquoise MACRO 05 = amber MACRO 13 = orange MACRO 06 = yellow MACRO 14 = cool white MACRO 07 = cyan MACRO 15 = warm white MACRO 08 = lavender

COLOUR CHANGE

In the colour change mode (jumping mode), 13 different colours alternate in rapid succession (red, green, blue, white, amber, yellow, cyan, lavender, pink, light green, magenta, turquoise, orange). The speed of the program is adjustable separately and a stroboscope effect can also be activated. Press the MODE button until "JUMPING" appears in the upper line of the display. Now, press ENTER until the cursor appears in the lower line of the display, and then select the rate (SPEED) using the UP and DOWN buttons, with the colours alternating from 00 to 99. Conﬁrm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". The cursor will appear in the bottom line at the same time and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the ﬂash frequency from 00 to 99 (FLASH:00 = strobe deactivated, FLASH: 01 = approx. 1 Hz, FLASH: 99 = approx. 20 Hz). Conﬁrm with ENTER.

COLOUR CHANGE

Rate SPEED:00 - SPEED:99

STROBOSCOPE

Flash frequency FLASH:00 - FLASH:99

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

OPERATION:

COLOUR BLENDING

In the colour fade mode (fading mode) different colours are blended into one another in succession. The speed of the program is adjustable separately and a stroboscope effect can also be activated. Press the MODE button until "FADING" appears in the upper line of the display. Now, press ENTER until the cursor appears in the lower line of the display, and then select the rate (SPEED) using the UP and DOWN buttons, with the colours alternating from 00 to 99. Conﬁrm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". The cursor will appear in the bottom line at the same time and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the ﬂash frequency from 00 to 99 (FLASH:00 = strobe deactivated, FLASH: 01 = approx. 1 Hz, FLASH: 99 = approx. 20 Hz). Conﬁrm with ENTER.

COLOUR BLENDING

Rate SPEED:00 - SPEED:99

STROBOSCOPE

Flash frequency FLASH:00 - FLASH:99

AUTO MODE

Press the MODE button repeatedly until "AUTO MODE" appears on the display. In this operating mode, the light switches automatically between colour change and colour blending mode. The colour change and/or colour blending rate is determined by the settings of the respective mode. A stroboscopic effect cannot be activated.

SLAVE MODE

Press the MODE button repeatedly until "SLAVE MODE" appears on the display. Connect the slave and the master unit (same series) with a DMX cable. Now the slave unit follows the master unit.

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

OPERATION:

SELECTING DMX MODE

Press the MODE button repeatedly until "DMX MODE" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select one of the ﬁve DMX modes (02CH, 03CH1, 03CH2, 05CH, 08CH). Conﬁrm with ENTER. You will ﬁnd tables with the channels of the different DMX modes on the following pages of this manual.

DMX START ADDRESS

Press the MODE button repeatedly until "DMX ADDR" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select the desired DMX start address between 001 and 512. Conﬁrm with ENTER.

LOCK FUNCTION

To protect the projector against accidental and unauthorised operation, there is a possibility to lock the controls. Press the UP and DOWN buttons simultaneously for 5 seconds. The display now shows LOCKED and it is no longer possible to change the settings of the projector using the control keys. To unlock, press the UP and DOWN buttons simultaneously for 5 seconds. Now the display will change to the previously displayed information.

AUTOLOCK

In addition to the ability to protect the projectors manually against accidental or unauthorised operation, this function can also be carried out automatically. Press the MODE button until "AUTOLOCK" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select the desired operating mode "ON" or "OFF". Conﬁrm with ENTER. Select "AUTOLOCK ON" and the controls of the projector are locked automatically after approx. 40 seconds and the lighting of the display goes out. To unlock, press the UP and DOWN buttons simultaneously for 5 seconds. Now the display will change to the previously displayed information.

NOTE: If the Autolock feature is disabled (AUTOLOCK OFF), the illumination of the LC display will be switched off automatically after about 40 seconds of inactivity. Pressing any one of the 4 control buttons will turn the illumination of the LC display on again.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

DMXCONTROL:

2-CHANNEL MODE

CHANNEL VALUE FUNCTION

CH1 000 - 255 Master dimmer (0 - 100%)

CH2

000 - 255 Colour Macros: 000 - 016 Red

017 - 033 Green

034 - 050 Blue

051 - 067 White

068 - 084 Amber

085 - 101 Yellow

102 - 118 Cyan

119 - 135 Lavender

136 - 152 Pink

153 - 169 Light Green

170 - 186 Magenta

187 - 203 Turquoise

204 - 220 Orange

221 - 237 Cool White

238 - 255 Warm White

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

DMXCONTROL:

3-CHANNEL MODE 1

CHANNEL VALUE FUNCTION

CH1 000 - 255 Master dimmer (0 - 100%) CH2 000 - 255 Stroboscope (rate 0 - 100%)

CH3

000 - 080 Colour Macros:

000 - 004 Blackout

005 - 010 Red

011 - 015 Green 016 - 020 Blue 021 - 025 White

026 - 030 Amber

031 - 035 Yellow

036 - 040 Cyan

041 - 045 Lavender

046 - 050 Pink

051 - 055 Light Green

056 - 060 Magenta

061 - 065 Turquoise

066 - 070 Orange

071 - 075 Cool White

076 - 080 Warm White

081 - 150 Colour Change (rate)

151 - 255 Colour Blending (rate)

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

DMXCONTROL:

3-CHANNEL MODE 2

CHANNEL VALUE FUNCTION

CH1 000 - 255 Red (0 - 100%) CH2 000 - 255 Green (0 - 100%)

CH3 000 - 255 Blue (0 - 100%)

5-CHANNEL MODE

CHANNEL VALUE FUNCTION

CH1 000 - 255 Red (0 - 100%) CH2 000 - 255 Green (0 - 100%) CH3 000 - 255 Blue (0 - 100%) CH4 000 - 255 White (0 - 100%) CH5 000 - 255 Amber (0 - 100%)

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

DMXCONTROL:

8-CHANNEL MODE

CHANNEL VALUE FUNCTION

CH1 000 - 255 Master dimmer (0 - 100%) CH2 000 - 255 Stroboscope (rate 0 - 100%)

CH3 000 - 255 Red (0 - 100%)

CH4 000 - 255 Green (0 - 100%)

CH5 000 - 255 Blue (0 - 100%)

CH6 000 - 255 White (0 - 100%)

CH7 000 - 255 Amber (0 - 100%)

CH8

000 - 080 Colour Macros:

000 - 004 Blackout / Colour Mixing CH3 - CH7

005 - 010 Red

011 - 015 Green

016 - 020 Blue

021 - 025 White

026 - 030 Amber

031 - 035 Yellow

036 - 040 Cyan

041 - 045 Lavender

046 - 050 Pink

051 - 055 Light Green

056 - 060 Magenta

061 - 065 Turquoise

066 - 070 Orange

071 - 075 Cool White

076 - 080 Warm White

081 - 150 Colour Change (rate)

151 - 255 Colour Blending (rate)

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

DMX CONNECTION:

DMX-512

DMX (Digital Multiplex) is the name of a universal transmission protocol for communication between corresponding devices and controllers. A DMX controller sends DMX data to the connected DMX device(s). The DMX data is always transmitted as a serial data stream that is forwarded from one connected device to the next via the "DMX IN" and "DMX OUT" connectors (XLR plug-type connectors) that are found on every DMX-capable device. (Most controllers only have a DMX output.)

DMX CONNECTION:

DMX is the common "language" via which a very wide range of types and models of equipment from various manufacturers can be connected with one another and controlled via a central controller, provided that all of the devices and the controller are DMX-compatible. For optimum data transmission, it is necessary to keep the connecting cables between the individual devices as short as possible. The order in which the devices are integrated in the DMX network has no influence on addressing. Thus the device with the DMX address 1 can be located at any position in the (serial) DMX chain: at the beginning, at the end or somewhere in the middle. If the DMX address 1 is assigned to a device, the controller "knows" that it should send all data allocated to address 1 to this device regardless of its position in the DMX network.

SERIAL CONNECTION OF MULTIPLE LIGHTS

1. Connect the male 3-pin IP65 connector of the DMX cable to the DMX output (female 3-pin connector) of the first projector or other DMX device.

2. Connect the female 3-pin IP65 connector of the DMX cable connected to the first projector to the DMXinput (male 3-pin connector) of the next DMX device. In the same way, connect the DMX output of this device to the DMX input of the next device and repeat until all devices have been connected. An extensive selection of suitable IP65 DMX extension cables, IP65 power extension cables and adapter cables, is available on the Internet at www.cameolight.com. Please note that as a rule, DMX devices are connected in series and connections cannot be shared without active splitters. The use of a terminator reduces interference and can prevent problems in signal transmission. Therefore, it is always advisable to insert a DMX end unit (resistance 120 Ohm, 1/4 W) between DMX- and DMX+ of the last device in the chain (dust- and jet-proof cable cap no. CLIPDMXTERM).

GENERAL INFORMATION ABOUT DMXCABLES:

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

NOTE:

• When fabricating your own cables, always observe the illustrations on this page. Never connect the shielding of the cable to the ground contact of the plug, and always make certain that the shielding does not come into contact with the housing of the XLR plug. If the shielding is connected to ground, this can lead to short-circuiting and system malfunctions.

PLEASE NOTE: TERMINATION:

• With extended cable runs, the last device in the chain may require a terminating resistor in order to prevent system malfunctions.

This is achieved by using a cable terminator module (Product No. K3DMXT3).

• Some manufacturers use 5-pole versions for data transmission instead of 3-pole XLR plugs. However, devices with 5-pole XLR connectors can also be integrated in a DMX network with 3-pole XLR connectors. In this case, a suitable cable adapter is required. The following illustration shows the correct pin-out of the corresponding plugs.

Use of a terminating resistor (termination) reduces interference and other problems during signal transmission. It is always advisable to connect a DMX termination module (resistance 120 ohms, 1/4 W) between pole 2 (DMX-) and pole 3 (DMX+) of the last device in the chain.

Usual connection

DMX-512 output 3-pole XLR

DMX-512 input 3-pole XLR

5-pole XLR(socket) Pole 1: Ground (shielding) Pole 2: Signal (-) Pole 3: Signal (+) Pole 4: unused Pole 5: unused

3-pole XLR(socket) Pole 1: Ground (shielding) Pole 2: Signal (-) Pole 3: Signal (+)

SPECIFICATIONS:

Model Name: CLPFLATPRO7IP65

Product Type: LED PAR can Type: Outdoor Flat PAR Colour Spectrum: RGBWA Number of LEDs: 7 LED Type: 10 W 5-in-1 Refresh Rate: 3000 Hz Dispersion Angle: 30° DMX Input: special IP65 connector, 3-pole, screw mount DMX Output: special IP65 connector, 3-pole, screw mount DMX Mode: 2-channel, 3-channel 1, 3-channel 2, 5-channel,

8-channel DMX Functions: colour change, colour blending, stroboscope, RGBWA Standalone Functions: colour change, colour blending, stroboscope, static

colours, colour macros, master/slave operation Controls: Mode, Enter, Up, Down Indicators: lit LC Display Operating Voltage: 110 - 240 V AC / 50 - 60 Hz Power Consumption: 40 W Power Connector: special IP65 connectors, screw-on, input and output Housing Material: die-cast metal Housing Colour: black Housing Cooling: convection (no fan) IP Protection Class: IP65 Dimensions (W x H x D, excluding bracket): 180 x 180 x 160 mm Weight: 5 kg Other Features: Screw end cap and DMX connection cable with

male 3-pin XLR connector included, screw-on mains

connection cable with Schuko plug included, screw

cap for power out included, multifunctional mounting

bracket

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

Model Name: CLPFLATPRO12IP65

Product Type: LED PAR can Type: Outdoor Flat PAR Colour Spectrum: RGBWA Number of LEDs: 12 LED Type: 10 W 5-in-1 Refresh Rate: 3000 Hz Dispersion Angle: 30° DMX Input: special IP65 connector, 3-pole, screw mount DMX Output: special IP65 connector, 3-pole, screw mount DMX Mode: 2-channel, 3-channel 1, 3-channel 2, 5-channel,

8-channel DMX Functions: colour change, colour blending, stroboscope, RGBWA Standalone Functions: colour change, colour blending, stroboscope, static

colours, colour macros, master/slave operation Controls: Mode, Enter, Up, Down Indicators: lit LC Display Operating Voltage: 110 - 240 V AC / 50 - 60 Hz Power Consumption: 90 W Power Connector: special IP65 connectors, screw-on, input and output Housing Material: die-cast metal Housing Colour: black Housing Cooling: convection (no fan) IP Protection Class: IP65 Dimensions (W x H x D, excluding bracket): 230 x 230 x 160 mm Weight: 6 kg Other Features: Screw end cap and DMX connection cable with

male 3-pin XLR connector included, screw-on mains

connection cable with Schuko plug included, screw

cap for power out included, multifunctional mounting

bracket

SPECIFICATIONS:

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

SPECIFICATIONS:

Model Name: CLPFLATPRO18IP65

Product Type: LED PAR can Type: Outdoor Flat PAR Colour Spectrum: RGBWA Number of LEDs: 18 LED Type: 10 W 5-in-1 Refresh Rate: 3000 Hz Dispersion Angle: 30° DMX Input: special IP65 connector, 3-pole, screw mount DMX Output: special IP65 connector, 3-pole, screw mount DMX Mode: 2-channel, 3-channel 1, 3-channel 2, 5-channel,

8-channel DMX Functions: colour change, colour blending, stroboscope, RGBWA Standalone Functions: colour change, colour blending, stroboscope, static

colours, colour macros, master/slave operation Controls: Mode, Enter, Up, Down Indicators: lit LC Display Operating Voltage: 110 - 240 V AC / 50 - 60 Hz Power Consumption: 125 W Power Connector: special IP65 connectors, screw-on, input and output Housing Material: die-cast metal Housing Colour: black Housing Cooling: convection (no fan) IP Protection Class: IP65 Dimensions (W x H x D, excluding bracket): 280 x 280 x 160 mm Weight: 7.5 kg Other Features: Screw end cap and DMX connection cable with

male 3-pin XLR connector included, screw-on mains

connection cable with Schuko plug included, screw

cap for power out included, multifunctional mounting

bracket

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

MANUFACTURER´S DECLARATIONS:

MANUFACTURER‘S WARRANTY

This warranty extends to the CAMEO branded product you purchased from Adam Hall. The statutory warranty rights against the vendor shall not be affected by this warranty. Rather, this warranty gives you additional independent claims against Adam Hall.

With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or Adam Hall partners, under normal use, are free of defects in material or workmanship for a period of 2 years from the date of purchase. The warranty period begins on the date of purchase. In order to assert a claim for warranty service, the proof of date of purchase is provided by the receipt bearing the date of purchase or the date of purchase on the delivery note. You are entitled to warranty service under the conditions and provisions set out in this document, if a repair within the warranty period is required.

This warranty applies only to the original purchaser of the products supplied by Adam Hall and is not transferable to any person to whom the property is transferred by the original purchaser. Within the warranty period, the defective parts or the product from Adam Hall will be repaired or replaced. Under the terms of this warranty, all the replaced or removed components become the property of Adam Hall.

In the unlikely event that a product acquired from Adam Hall, repeatedly exhibits a defect, Adam Hall may decide, at its discretion, to replace this product with a comparable product of at least the same performance.

Adam Hall does not guarantee that the operation of this product will be uninterrupted or error-free. Adam Hall accepts no responsibility for any damage due to incorrect compliance with the instructions received in the delivery.

This warranty does not extend to:

- wearing parts (eg battery, tubes).

- devices that have had their serial number removed or damaged, or failed as a result of an accident

- inappropriate or abusive use or other external causes

- devices that were not used in accordance with the operating parameters deﬁned in the user documentation shipped with the product

- devices that have been repaired using parts not made or distributed by Adam Hall

- devices that have been serviced, modiﬁed or repaired by someone other than Adam Hall or an authorised service partner. These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam Hall regarding the Adam Hall branded product you have purchased.

This warranty is valid only within Europe. Outside of Europe please contact our ofﬁcial distributors.

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

MANUFACTURER´S DECLARATIONS:

LIMITATION OF LIABILITY

If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid for the product or the cost of repair or replacement of any components that malfunction under conditions of normal use.

Adam Hall is not liable for any damages caused by the product or the failure of the product, including any lost proﬁts or savings or special, incidental, or consequential damages. Adam Hall is not liable for any claim made by a third party or made by you for a third party.

This limitation of liability applies whether damages are sought, or claims are made, under this Limited Warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim, and cannot be rescinded or changed by anyone. This limitation of liability will be effective even if you have advised Adam Hall or an authorized representative of Adam Hall of the possibility of any such damages, but not, however, in the event of claims for damages in connection with personal injuries.

This manufacturer‘s warranty grants you speciﬁc rights; depending on jurisdiction (nation or state), you may be be entitled to additional claims. You are advised to consult applicable state or national laws for a full determination of your rights.

REQUESTING WARRANTY SERVICE

To request warranty service for the product, contact Adam Hall or the Adam Hall authorized reseller from which you purchased the product.

EC DECLARATION OF CONFORMITY

The equipment marketed by Adam Hall complies (where applicable) with the essential requirements and other relevant speciﬁcations of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional information can be found at www.adamhall.com.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

MANUFACTURER´S DECLARATIONS:

PROPER DISPOSAL OF THIS PRODUCT

(Valid in the European Union and other European countries with waste separation)

This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity.

Household users should contact either the retailer where they purchased this product, or their local government ofﬁce, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal .

ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION

Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug.

Adam Hall GmbH, all rights reserved. The technical data and the functional product characteristics can be subject to modiﬁcations. The photocopying, the translation, and all other forms of copying of fragments or of the integrlity of this user’s manual is prohibited.

Einleitung

Die nach EN 60529 als Gerät der Schutzart IP65 klassiﬁzierten professionelle PAR Scheinwerfer der Cameo FLAT PRO OUTDOOR Serie liefern lebendige Farben für den Einsatz im Außenbereich. Die extrem kompakten Gehäuse eignen sich perfekt für Umgebungen mit begrenztem Platzangebot, wobei das passive Kühlkonzept für einen zu 100% geräuschlosen Betrieb sorgt. Mit ihren 10 Watt Hochleistungs-RGBWA-LEDs ermöglichen die Scheinwerfer vielseitige Farbmischungen von weichen Pastelltönen bis hin zu satten, warmen Farben, die mit einer beeindruckenden Helligkeit und einem Abstrahlwinkel von 30° ausgegeben werden. Darüber hinaus garantiert die Wiederholfrequenz von 3.000 Hz einen absolut ﬂackerfreien Betrieb.

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

Wir freuen uns, dass Sie sich für ein Produkt von Cameo Light entschieden haben!

Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele Jahre einen reibungslosen Betrieb zu gewährleisten.

Bitte lesen Sie diese Bedienungsanleitung sorgfältig, damit Sie Ihren neuen Scheinwerfer von Cameo Light schnell optimal einsetzen können.

Weitere Informationen über Cameo Light erhalten Sie auf unserer Website WWW.CAMEOLIGHT.COM.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

FLAT PRO OUTDOOR PAR CAN

7 X 10W LED RGBWA PAR CAN CLPFLATPRO7IP65 12 X 10W LED RGBWA PAR CAN CLPFLATPRO12IP65 18 X 10W LED RGBWA PAR CAN CLPFLATPRO18IP65

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

SICHERHEITSHINWEISE:

1. Lesen Sie diese Anleitung bitte sorgfältig durch.

2. Bewahren Sie alle Informationen und Anleitungen an einem sicheren Ort auf.

3. Befolgen Sie die Anweisungen.

4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheitshinweise oder andere Informationen vom Gerät.

5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.

6. Verwenden Sie ausschließlich stabile und passende Stative bzw. Befestigungen (bei Festinstallationen). Stellen Sie sicher, dass Wandhalterungen ordnungsgemäß installiert und gesichert sind. Stellen Sie sicher, dass das Gerät sicher installiert ist und nicht herunterfallen kann.

7. Beachten Sie bei der Installation die für Ihr Land geltenden Sicherheitsvorschriften.

8. Installieren und betreiben Sie das Gerät nicht in der Nähe von Heizkörpern, Wärmespeichern, Öfen oder sonstigen Wärmequellen. Sorgen Sie dafür, dass das Gerät immer so installiert ist, dass es ausreichend gekühlt wird und nicht überhitzen kann.

9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf dem Gerät.

10. Lüftungsschlitze dürfen nicht blockiert werden.

11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Wasser (gilt nicht für spezielle Outdoor Geräte beachten Sie in diesem Fall bitte die im Folgenden vermerkten Sonderhinweise). Bringen Sie das Gerät nicht mit brennbaren Materialien, Flüssigkeiten oder Gasen in Berührung.

12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das Gerät eindringen kann. Stellen Sie keine mit Flüssigkeit gefüllten Behältnisse wie Vasen oder Trinkgefäße auf das Gerät.

13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen können.

14. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen und vorgesehenen Zubehör.

15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.

16. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um Schäden oder Unfälle, z. B. durch Stolperfallen zu vermeiden.

17. Achten Sie beim Transport darauf, dass das Gerät nicht herunterfallen und dabei möglicherweise Sach- und Personenschäden verursachen kann.

18. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegenstände in das Geräteinnere gelangt sind, oder das Gerät anderweitig beschädigt wurde, schalten Sie es sofort aus und trennen es von der Netzsteckdose (sofern es sich um ein aktives Gerät handelt). Dieses Gerät darf nur von autorisiertem Fachpersonal repariert werden.

19. Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch.

20. Beachten Sie alle in Ihrem Land geltenden Entsorgungsgesetze. Trennen Sie bei der Entsorgung der Verpackung bitte Kunststoff und Papier bzw. Kartonagen voneinander.

21. Kunststoffbeutel müssen außer Reichweite von Kindern aufbewahrt werden.

BEI GERÄTEN MIT NETZANSCHLUSS:

22. ACHTUNG: Wenn das Netzkabel des Geräts mit einem Schutzkontakt ausgestattet ist, muss es an einer Steckdose mit Schutzleiter angeschlossen werden. Deaktivieren Sie niemals den Schutzleiter eines Netzkabels.

23. Schalten Sie das Gerät nicht sofort ein, wenn es starken Temperaturschwankungen ausgesetzt war (beispielsweise nach dem Transport). Feuchtigkeit und Kondensat könnten das Gerät beschädigen. Schalten Sie das Gerät erst ein, wenn es Zimmertemperatur erreicht hat.

24. Bevor Sie das Gerät an die Steckdose anschließen, prüfen Sie zuerst, ob die Spannung und die Frequenz des Stromnetzes mit den auf dem Gerät angegebenen Werten übereinstimmen. Verfügt das Gerät über einen Spannungswahlschalter, schließen Sie das Gerät nur an die Steckdose an, wenn die Gerätewerte mit den Werten des Stromnetzes übereinstimmen. Wenn das mitgelieferte Netzkabel bzw. der mitgelieferte Netzadapter nicht in Ihre Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCH

ENGLISH

SICHERHEITSHINWEISE:

25. Treten Sie nicht auf das Netzkabel. Sorgen Sie dafür, dass spannungsführende Kabel speziell an der Netzbuchse bzw. am Netzadapter und der Gerätebuchse nicht geknickt werden.

26. Achten Sie bei der Verkabelung des Geräts immer darauf, dass das Netzkabel bzw. der Netzadapter stets frei zugänglich ist. Trennen Sie das Gerät stets von der Stromzuführung, wenn das Gerät nicht benutzt wird, oder Sie das Gerät reinigen möchten. Ziehen Sie Netzkabel und Netzadapter immer am Stecker bzw. am Adapter und nicht am Kabel aus der Steckdose. Berühren Sie Netzkabel und Netzadapter niemals mit nassen Händen.

27. Schalten Sie das Gerät möglichst nicht schnell hintereinander ein und aus, da sonst die Lebensdauer des Geräts beeinträchtigt werden könnte.

28. WICHTIGER HINWEIS: Ersetzen Sie Sicherungen ausschließlich durch Sicherungen des gleichen Typs und Wertes. Sollte eine Sicherung wiederholt auslösen, wenden Sie sich bitte an ein autorisiertes Servicezentrum.

29. Um das Gerät vollständig vom Stromnetz zu trennen, entfernen Sie das Netzkabel bzw. den Netzadapter aus der Steckdose.

30. Wenn Ihr Gerät mit einem Volex-Netzanschluss bestückt ist, muss der passende Volex-Gerätestecker entsperrt werden, bevor er entfernt werden kann. Das bedeutet aber auch, dass das Gerät durch ein Ziehen am Netzkabel verrutschen und herunterfallen kann, wodurch Personen verletzt werden und/oder andere Schäden auftreten können. Verlegen Sie Ihre Kabel daher immer sorgfältig.

31. Entfernen Sie Netzkabel und Netzadapter aus der Steckdose bei Gefahr eines Blitzschlags oder wenn Sie das Gerät länger nicht verwenden.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ACHTUNG:

Entfernen Sie niemals die Abdeckung, da sonst das Risiko eines elektrischen Schlages besteht. Im Inneren des Geräts beﬁnden sich keine Teile, die vom Bediener repariert oder gewartet werden können. Lassen Sie Reparaturen ausschließlich von qualiﬁziertem Servicepersonal durchführen.

Das gleichschenkelige Dreieck mit Blitzsymbol warnt vor nichtisolierten, gefährlichen Spannungen im Geräteinneren, die einen elektrischen Schlag verursachen können.

Das gleichschenkelige Dreieck mit Ausrufungszeichen kennzeichnet wichtige Bedienungs- und Wartungshinweise.

VORSICHT! WICHTIGE HINWEISE IN BEZUG AUF LICHT-PRODUKTE

1. Blicken Sie nicht aus Entfernungen von unter 40 cm in den Lichtstrahl.

2. Blicken Sie niemals längere Zeit aus kurzem bis mittlerem Abstand in den Lichtstrahl.

3. Blicken Sie niemals mit optischen Geräten wie Vergrößerungsgläsern in den Lichtstrahl.

4. Stoboskopeffekte können unter Umständen bei empﬁndlichen Menschen epileptische Anfälle auslösen! Epilepsiekranke Menschen sollten daher unbedingt Orte meiden, an denen Stroboskope eingesetzt werden.

Das Produkt ist für den professionellen Einsatz im Bereich der Veranstaltungstechnik entwickelt worden und ist nicht für die Raumbeleuchtung in Haushalten geeignet.

EINFÜHRUNG:

7 x 10W 5IN1 LED RGBWA FLAT PAR OUTDOOR SCHEINWERFER

CLPFLATPRO7IP65

STEUERUNGSFUNKTIONEN:

• 2-Kanal, 3-Kanal 1, 3-Kanal 2, 5-Kanal und 8-Kanal DMX-Steuerung

• Rot, Grün, Blau, Weiß und Amber separat steuerbar

EIGENSCHAFTEN:

• Strahlwassergeschützt nach EN 60529

• 7 x 10W 5in1 LEDs

• Farbspektrum RGB + Weiß + Amber

• 30° Abstrahlwinkel

• Wiederholrate 3000 Hz

• Geräuschloser Betrieb dank Konvektionskühlung

• 40W Leistungsaufnahme

• Betriebsspannung 110V - 240V AC

• IP65 Spezialverbinder für die Spannungsversorgung

• IP65 Spezialverbinder für DMX In und Out

• Beleuchtetes, multifunktionales LC-Display

• Verstellbarer multifunktionaler Montagebügel

• Master/Slave-Betrieb

• Farbwechselgeschwindigkeit und Stroboskopeffekt über Bedienpanel und DMX und steuerbar

12 x 10W 5IN1 LED RGBWA FLAT PAR OUTDOOR SCHEINWERFER

CLPFLATPRO12IP65

STEUERUNGSFUNKTIONEN:

• 2-Kanal, 3-Kanal 1, 3-Kanal 2, 5-Kanal und 8-Kanal DMX-Steuerung

• Rot, Grün, Blau, Weiß und Amber separat steuerbar

EIGENSCHAFTEN:

• Strahlwassergeschützt nach EN 60529

• 12 x 10W 5in1 LEDs

• Farbspektrum RGB + Weiß + Amber

• 30° Abstrahlwinkel

• Wiederholrate 3000 Hz

• Geräuschloser Betrieb dank Konvektionskühlung

• 95W Leistungsaufnahme

• Betriebsspannung 110V - 240V AC

• IP65 Spezialverbinder für die Spannungsversorgung

• IP65 Spezialverbinder für DMX In und Out

• Beleuchtetes, multifunktionales LC-Display

• Verstellbarer, multifunktionaler Montagebügel

• Master/Slave-Betrieb

• Farbwechselgeschwindigkeit und Stroboskopeffekt über Bedienpanel und DMX und steuerbar

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS

ESPAÑOLPOLSKIITALIANO

+ 118 hidden pages

Cameo FLAT PRO CLPFLATPRO7IP65, FLAT PRO CLPFLATPRO12IP65, FLAT PRO CLPFLATPRO18IP65 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual