Camden Door Controls CV-920-CH, CV-920-RD, CV-920-SL, CV-920-WH Installation Instructions

Page 1
Feature
• Multi protocol peripheral keypad
• Operates on 12V DC
• Indoor/outdoor use
• Compatible with WIEGAND 26, 30, 34, 40bit,
Clock & Data
• Red, Green and Orange LEDs
• Audible and visual feedback
• Resin Potted electronics
• Current Consumption: 45 mA
• Backlit keys
• Selectable PIN Code length
• Dustproof and waterproof (IP65)
• Operating Temperature : -4ºF to +122ºF (-20ºC to +50ºC)
2”
(51mm)
CV-920 Series
Installation Instructions
3 5/8”
(92mm)
Mounting
1.
2. 3.
Cable
4. 5.
1”
(25mm)
gnd d0 d1 xx xx xx xx
Page 1 of 5
Page 2
Wiring
C17
C41
A
LD12
R36
R18
R25
R24
C40
R10
C34
L10 L11
C18
C33
R9
C42
C1
R5
R45
C43
C44
R28
R21
C45
C3
C5
R38
R19
R37
A
LD17
A
LD19
A
LD18
C16
C15
RX4
D5
D10
A
LD24
A
LD11
R49
IC6
ZD5
ZD6
R22
L3
R53
R34
TAS1
IC11
R15
IC15
R47
R20
R16
R11
C2
X1
C4
C13
C12
ICN1
R23
R48
X3
IC1
C6
U5
L5
L4
R54
R50
IC12
R17
R62
A
LD23
D3
D2
RX3
Rb6
IC2
R30
A
LD22
BAT
U1
IC5
FUSE2
IC3
U4
IC1
A
B
RS485
A
R1
Door Sensor2
Door Sensor1
Exit Button1
Exit Button2
GND
GND
Free In 2 -
Free In 2 +
Free In 1 -
Free In 1 +
Rx
Tx
Busy
12V
5V
3.3V
System
OK
TCP/IP
12Vdc Out
CV-920 Series
Red
Black Pink
Violet
Orange Green
Gray
Yellow
White
12V DC
GND
Tamper Tamper
LED Red LED Green
Codix
D1/data
D0/ clock
Reset the Master Code
1. Disconnect Power
2. Press and hold “A” and reconnect Power.
3. Hold the “A” Key for at least 3 seconds.
COLOUR CONNECTION
Red
Black
Pink
Violet
Orange
Green
Grey
Yellow
White
12V DC Power GND
Supply
Tamper
LED - Red LED - Green N/A D1/ data D0/ clock
Relays
Wiegand/ Clock & Data
12V DC
GND
Tamper
Tamper
LED Red -
LED Green -
D1/ data
D0/ clock
12V DC
Ground
Tamper Switch
Tamper Switch
Red LED -
Green LED -
Data 1/ Data
Data 0/ Clock
WIEGAND Connection
led1
LD14
R46
led2
LD16
A
Green
Orange
Black
Red
White
Yellow
Led Green -
Led Red -
GND
12 VDC
D0
D1
Max. 50m
Page 2 of 5
R55
GND led1 D0
R14
ZD4
L9
R3
R4
+12V
D0 D1
R2
led2
GND
+12V
D1
GND
+12V
L8
C32
IC8
A
FUSE1
LD13
A
LD15
R13
ZD1
R2
L7
R1
L6
C27
IC7
Fuse
ICN2
L1
D13
L2
CV-350
Page 3
Clock & Data Connection
CV-920 Series
Tamper
Black
Red
White
Yellow
Violet
Pink
GND
12 VDC
D0/Clock
D1/Data
Yellow
Max. 50m
Pink
Violet
Black
Red
White
GND
+12V
CL
DA
Controller
Page 3 of 5
Green LED
Free tension
Red LED
Free tension
Orange LED
Key press and Menu
Page 4
Programming Flowchart
Enter “Master Code” B + 000000
Error Beep
Validation OK?
Yes
1 small beep + 1 long beep + Orange LED is ‘ON’
No
(3 short beeps)
CV-920 Series
Change
Master Code
1
Enter New
Master Code
Press 6 Digits
Select Type of Wiegand
1
Wiegand
26bit
2
Wiegand
30bit
Direct Menu exit
Select Output Protocol
1 2
Single
Wiegand
2
3
34bit
4
Wiegand
40bit
Wiegand
3
Double
Wiegand
3
Clock &
Data
PIN Code Length
4
0
for any length
with “A”
in the end
1 - 8
for lengths
between
1 to 8 digits
Press “A” to validate and exit the menu
1 2
Wiegand
26bit
normal
(orange LED OFF)
Entering Menu is always done with B + 000000 if the Master Code is not changed.
Submenu 1 - Change Master Code. The Master Code must be 6 digits. After enrolling new Master Code the CV-920 automatically exits the Menu and the new master code must be typed to enter the menu.
Submenu 2 - Select Type of Wiegand. With this the Keypad can be adjusted to send 4 different Wiegand Outputs. The Wiegand selected must be the same as the controller’s Wiegand Input that the CV-920 Keypad is being connected to. Example: If you use a controller that recognizes Wiegand 34bit, then enter the menu of CV-920, press 2, then press 3.
Submenu 3 - Select Output Protocol. The Keypad can send the Code by different Protocols. Use “Single Wiegand” when connected to third party controllers. When “Single Wiegand” is selected, what is typed on the Keypad is sent as a Wiegand Number. Use Double Wiegand when connected to CV-350, use Clock&Data when connected to controller with Clock & Data input.
Submenu 4 - PIN Code Length. If “0” is selected, then any PIN Code with any length can be sent, but the PIN Code must be followed with “A” for confirmation ( ex. 123 + A). If 1 to 8 is selected the PIN Code length is determinated by the number selected.
Presets
Wiegand
34bit
normal
6
Wiegand
3
34bit
CV-350
4
Wiegand
26bit
CV-350
Site Code Length
Enter Site
Code
8
5 digits
Backlight
7
1 2
Site Code
No Site
between
Code
0 to 15
Submenu 6 - Presets. The Presets are a set of preprogrammed parameters for easy programming.
6-1 “Wiegand 26bit Normal” - Type: Wiegand 26bit; Output: Single Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
6-2 “Wiegand 34bit Normal” - Type: Wiegand 34bit; Output: Single Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
6-3 “Wiegand 34bit CV-350 Mode” - Type: Wiegand 34bit; Output: Double Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
6-4 “Wiegand 26bit CV-350 Mode” - Type: Wiegand 26bit; Output: Double Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
Presets 6-3 and 6-4 to be used always when CV-920 is connected to CV-350 firmware ver.2.42 or higher.
Submenu 7 - Site Code Length. Set the code length sent to Host. Defaul is “0”. To be used only in specific cases.
Submenu 8 - Enter Site Code. Put the site code always in 5 digit format (ex. 00170).
Submenu 9 - Backlight. Turns ON/OFF the backlight.
3
Site Code
between 0 to 255
4
Site Code
between
0 to 65535
Backlight
OFF
9
0 1
Backlight
ON
Page 4 of 5
Page 5
Connecting CV-920 to CV-350 Controller
When CV-920 is connected to CV-350 Controller, settings must be done in the CAMS Software and in the CV-920 Keypad.
CV-920 Series
Example: Create a User to access with Card or PIN Code. The Card Number is 8744987 and the PIN Code 12345.
Settings in the CAMS Software
1.
In the CAMS Software, right click on the Reader and select properties. In the Properties window select for Type: “CV-920”
(1.1)
2. Select the Wiegand 26 bit (1.2)
3. Press Save & Exit. In the event window a confirmation message will appear as shown in (fig.2)
4. Adjust the PIN Length. Go to Settings/ System parameters. For Keycode length select 5 digits. (fig3)
5. Go To Users Menu and select the user. In the Field User ID (Card Number) write 8744987. In the Field ”Access Code” write the PIN Code 12345. Save the User. (fig.4)
Settings in the CV-920
1.
Enter the Menu of CV-920. Press B+000000.
2. Press 6, press 4. The Preset, programs the CV-920 Keypad to work with CV-350 controller in Wiegand 26bit.
g.2
g.3
3. Adjust the PIN Length. Press 4, then press 5. Type 12345 and access will be granted.
g.4
Questions? Call us toll-free at 1-877-226-3369
Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control
5502 Timberlea Blvd., Mississauga, ON Canada L4W 2T7
www.camdencontrols.com Toll Free: 1.877.226.3369
Page 5 of 5
File: CV-920 Series Installation Instructions.indd R1 Revision: 06/05/2015 Part No.: 40-82B171
Loading...