GS2020E GigaSPIRE BLAST
GS2025E GigaSPIRE GO
GS2026E GigaSPIRE MAX
Quick Start Guide
This document provides general installation practices for the
family of three Calix GigaSPIRE Service Delivery Platforms.
This document also provides guidance for site preparation,
installation, and basic troubleshooting.
Scan the QR code at left to access the
installation instructions for this product. All
product documentation is available online
from the Calix Resource Center (support.
calix.com).
Package Contents
GigaSPIRE - Model GS2020E, GS2025E, or GS2026E
Power adapter with cord
GigaSPIRE Quick Start Guide (this document)
Alexa Set-up Guide (Model GS2025E and GS2026E
only)
P/N 220-01093, Rev 10
A Quick Look
GS2025E GigaSPIRE GO
GS2026E GigaSPIRE MAX
WiFi Protected Set-up
(WPS)
Mechanical Reset
10/100/1000 Base-T
Ethernet, RJ-45 (x2)
USB 3.0
3.5 mm Sound Jack
Power In (2-Pin Barrel)
7887
Top Vie w
+
_
Volum e Up
Volum e Mu te
Action Button
Volum e Do wn
Light Bar
GS2020E GigaSPIRE BLAST
WiFi Protected Set-up
(WPS)
Mechanical Reset
10/100/1000 Base-T
Ethernet, RJ-45 (x2)
USB 3.0
Power In (2-Pin Barrel)
7901
Top Vie w
Light Bar
Brief Overview
The GigaSPIRE family off ers the following key features:
Dual Functionality - The GigaSPIRE family may be
implemented as either a residential gateway or can be
deployed as a Wi-Fi Mesh point. The role the GigaSPIRE
plays in your whole home solution is dependent on the
software installed at the time of deployment.
Extremely User-Friendly Installation - Using the Calix
Smart Activate feature with a buttset or laptop, technicians can install and apply subscriber service profi les
- 2 -
without assistance from the central offi ce. Remotely manageable using Compass software (including Consumer Connect
Plus), confi guration, activation and software upgrades are
easily accomplished via in-band management or a standard
TR-069 interface.
GigaBit Subscriber Experience - The GS2025E AND
GS2026E extends the access network into the home for
controlling the Internet of Things (IoT) and voice recognition
experience. In addition to supporting broadband connectivity
for data and video services, the GS2025E and the GS2026E
service platforms provides a premises-based Wireless
Access Point (WAP) that supports IoT connectivity, and the
802.11ax Wi-Fi technology with voice recognition capabilities.
- 3 -
Mounting the GigaSPIRE
All GigaSPIRES must be placed on a tabletop or shelf in an
upright orientation.
4.80 inches
12.2 cm
4.80 inches
12.2 cm
7902
8.90 Inches
22.6 cm
- 4 -
Powering the GigaSPIRE
To power the equipment:
1. Remove any protective packaging or fi lm prior to powering up the GigaSPIRE.
2. Plug in the power adapter to any available wall socket
and attach the other end to the power port. Note the
power cord is 5 feet (1.5 meters) long.
Power In (2-Pin Barrel)
7903
Managing the GigaSPIRE
To manage the functions of the GigaSPIRE, an Embedded
Web Interface (EWI) is included. To access the EWI of the
GigaSPIRE, connect an Ethernet cable from your PC to the
GigaSPIRE and enter the default IP Address of the device
(192.168.1.1)
- 5 -
Managing Wi-Fi Services
Out of the box, the GigaSPIRE Wi-Fi radios are enabled.
After power is applied, the Wi-Fi radios are functional using
the following default settings.
• SSID: Printed on product label (CXNKxxxxxxxx)
• Number of Radios: 2 (2.4 GHz and 5 GHz)
• Wi-Fi Protocol:802.11a/b/n/g/ac/ax
• Credentials: Login and password printed on label
Connecting the GigaSPIRE to your Network
To complete the network connection, two options exist:
1. If the GigaSPIRE is confi gured as a Residential Gateway, connect an Ethernet Cable to it’s WAN port from
the WAN modem (ONU, cable modem, DSL modem
and the like).
2. If the GigaSPIRE is confi gured as the MESH point,
either connect an Ethernet cable from its WAN port
to another GigaSPIRE (RG) or wirelessly connect the
device.
3. Once connected using either method, the GigaSPIRE
can be confi gured via the EWI.
About Interactive Voice Recognition (IVR)
The GS2025E and GS2026E GigaSPIRE supports Amazon
Alexa IVR and is compatible with the following languages:
English (US/UK/CAN) Australia India
- 6 -
The top panel includes controls for managing the IVR functions on these models. Four rocker buttons control:
• Volume Up and Down
• Microphone Mute
• Action Button
Note that the GigaSPIRE model GS2020E does not support
IVR and IoT functionality.
Refer to the Alexa Start-up Guide for additional information.
Supported Use Cases
The GS2025E and GS2026E GigaSPIRE supports the
following use cases:
• GigaBit Wi-Fi Whole Home Coverage - Whole Home
Coverage means other forms of home networking are
not needed (i.e., MoCA or PLC).
• GigaBit Wi-Fi Whole Home Coverage with IVR Amazon Alexa application available anywhere in the
home where a GigaSPIRE is present. (Not supported
on GS2020E)
• GigaBit Wi-Fi Whole Home Coverage with IVR and
Internet of Things (IoT) - Smart Home technology
including Zigbee, Z-Wave, and Broadband Loop Emulation (BLE). (Not supported on GS2020E)
- 7 -
Safety
Potentially Explosive Atmosphere
Do not use the GigaSPIRE in an area where a potentially
explosive atmosphere exists.
Atmosphère potentiellement explosive
N’utilisez pas le GigaSPIRE dans un endroit où existe une
atmosphère potentiellement explosive.
Intended Use
This product is classifi ed as telecommunication equipment
not intended for direct purchase by the public.
This product is designed and approved for use in an indoor
location only.
CAUTION! Use of any controls, adjustments,
or procedures other than those specifi ed herein
!
may result in hazardous radiation exposure.
Utilisation prévue
Ce produit est classé comme équipement de télécommunication non destiné à l’achat direct par le public.
Ce produit est conçu et approuvé pour utilisation en intérieur
uniquement.
- 8 -
MISE EN GUARDE ! L’utilisation de contrôles,
réglages ou procédures autres que ceux
!
spécifi és dans ce manuel peut entraîner une
exposition dangereuse à des rayonnements.
Power Supply
• Ensure that a suitable AC power outlet is situated near
the GigaSPIRE and easily accessible.
• Connect the power supply cord only to the AC power
outlet that meets the specifi cations marked next to the
appliance AC power inlet on the GigaSPIRE.
• Never alter the AC power cord. If necessary have the
correct outlet installed by a qualifi ed electrician or call
your service provider for assistance.
• To reduce the risk of damage to the electric cord,
remove it from the outlet by holding onto the AC power
adapter rather than the cord. Make sure the cord is positioned so that it will not be stepped on, tripped over
or otherwise subjected to damage or stress.
WARNING! Do not use any other power
adapter except the one that accompanies
!
this unit or a power supply identifi ed in the list
below. Use of another adapter could result
in damage to the unit. To prevent electrical
shock, please do not open the cover. The
following power adapter is qualifi ed for use
with this GigaSPIRE.
- 9 -
This GS2026E/GS2025E/GS2020E must be powered by
Frecom F60-120500SPA or equivalent
UL Listed LPS power source rated at:
Input: 90-264 VAC, 47/63 Hz, 1.6A,
Output: Nominal 12 VDC, 5A Minimum, 60W
Alimentation électrique
• Assurez-vous qu’une prise de courant C.A. appropriée est
située près du GigaSPIRE et qu’elle soit facile d’accès.
• Connectez le câble d’alimentation uniquement à une prise
de courant qui correspond aux spécifi cations indiquées à
côté de l’entrée d’alimentation du GigaSPIRE.
• Ne modifi ez jamais le câble d’alimentation. Si nécessaire,
faîtes installer la bonne prise de courant par un électricien
qualifi é ou Contactez votre prestataire de services pour
assistance.
• Pour réduire le risque de dommage au câble électrique,
retirez-le de la prise de courant en tenant l’adaptateur
secteur plutôt que le câble. Assurez-vous que le câble
est positionné de manière à éviter qu’il soit possible de
marcher ou trébucher dessus, ou de l’endommager.
- 10 -
Attention ! N’utilisez pas d’autre adaptateur
secteur que celui qui accompagne cet appareil
!
ou une alimentation électrique autre que celle
identifi ée dans la liste ci-dessous. L’utilisation
d’un autre adaptateur pourrait endommager
l’appareil. Pour éviter les chocs électriques,
n’ouvrez pas le couvercle. L’adaptateur électrique suivant est qualifi é pour être utilisé avec
le GigaSPIRE.
L’adaptateur électrique suivant est qualifi é
pour être utilisé avec le GigaSPIRE
Ce GigaSPIRE doit être alimenté par un adapteur
Frecom F60-120500SPA ou une source d’alimentation
équivalente certifi ée UL LPS de capacité:
Entree: Input: 90-264 VAC, 47/63 Hz, 1.6A,
Sortie: Valeur nominale 12 VDC, 5A Minimum, 60W
Children
Do not allow children to play with the GigaSPIRE. It contains
small parts that could become detached and create a choking hazard.
Environmental Conditions
Maximum environmental values during use:
Temperature: 0° C to +40° C (32° to 104° F), Humidity: 10%
to 90% RH, non-condensing, 200 - 10,000 feet altitude.
- 11 -
License Information
Open Source Software Utilization Notice
The GigaSPIRE family uses Open Source software programs. Such software programs are made available subject
to certain third-party terms and conditions.
The fact that you are about to begin using or have purchased
this product requires that you be informed of the use of these
software packages and or libraries and in some cases, the
third-party terms and conditions applicable to such software.
This information can be found on the manufacturer’s support
portal. Refer to the appropriate software release notes for
additional information on Open Source software programs
used by this product.
- 12 -
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 27cm between the radiator & your body.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmfu l interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz
shall be such that the equipment still complies with the e.i.r.p. limits specified for
point-to-point
and non-point-to-point operation as appropriate; and
(iii) Users should also be advised that high-power radars are allocated as primary
users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5
850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à
point et l’exploitation non point à point, selon le cas;
(iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité)
pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage
et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 33cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED
établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 33 cm de distance entre la source de rayonnement et votre
corps.
Loading...