Bush WMNSN612W, WMNB712EW, WMNB812EW, WMNB912EW, WMNB1012EW Quick Start Guide

...

Using your washing machine for the ﬁrst

Temperature selection

You can select the washing water temperature

with the washing water temperature selection

button.

time

Let’s get started

your laundry by using this additional function.

You may make the programme active by

pressing the extra rinsing function button

when the LED light of the symbol turns

on.

Troubleshooting

Help and assistance

If you require any technical guidance or find that your WMNSN612W - WMNB712EW -

WMNB812EW - WMNB912EW - WMNB1012EW - WMNB712EB - WMNB812EB - WMNB912EB

- WMNB1012EB washing machine is not operating as intended, a simple solution can often be

found in the Troubleshooting section of the instruction manual or online at www.bush-support.

com

If you still require further assistance, call one of our experts on 0345 257 7271*. To help us give

you a fast and efficient service please have the following information ready:

Help is always at hand

Quick start guide

Washing Machine

WMNSN612W

WMNB712EW WMNB812EW WMNB912EW

WMNB1012EW

WMNB712EB WMNB812EB WMNB912EB

WMNB1012EB

Contact:

www.bush-support.com

Helpline: 0345 257 7271

52257844

Auxiliary function button 1

Spin Speed Selection

You can adjust the spin speed of your laundry

with the spin speed setting button.

Auxiliary function button 3

Pre-wash

You can expose your very dirty laundries to

prewashing operation prior to main washing

by using this additional function.

When using this function, you should put

detergent in front washing compartment of

the detergent drawer.

Model Ref.

Serial number

Date of purchase

Local call rates applies*

You can find these on the rating plate - a small information panel (usually a sticker or metal plate) on the rear of your appliance

This will be shown

on your receipt

Lines open 8am-7pm Monday to Saturday and 10am-4pm Sunday.

Auxiliary function button 2

Auxiliary function

Extra Rinse

You can make additional rinse operation on

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions, or online at www.bush-support.com If you still require further assistance, call one of our experts on 0345 257 7271.

button 4

*Calls to Bush enquiry lines may attract a charge and set up fee from residential lines depending on your call plan/tari. Mobile and other providers costs may vary, see www.bt.com/pricing for details.

For security and training purposes, telephone calls to and from customer service centres may be recorded and monitored. Calls from Republic of Ireland will attract international call charges.

Unpacking

Installing your washing machine

Using your washing machine for the ﬁrst

You’ll soon be enjoying your new appliance

This guide will help you get started, full details of your washing machine and its features can be found in the instruction manual.

Accessories

This machine includes the below accessories,

please install these parts before operating.

• Plastic hole plug x 4

• Inlet hose

Bringing it all together

2 3 4 8 9

7 7

Front Back

1. Detergent drawer

2. Top panel

3. Programme knob

4. Start/Pause button

5. Door

6. Filter

7. Packing bolt x 4

* Make sure to remove the transit bolts prior to first use.

8. Power lead

9. Drain hose

10. Water inlet

Bringing it all together

Connections

Electrical

• Any electrical work that is required

to install this washing machine

MUST be carried out by a qualified

electrician.

• Ensure the power socket is suitable for

the maximum power of the washing

machine (fuses in the power circuit must

be 13 amp).

• The appliance must be connected to

a 220-240 volt 50 cycle AC supply by

means of a three pin socket, suitably

earthed and protected by a 13 amp fuse.

• Should the fuse need to be replaced, a

13 amp fuse approved to BS1363/A must

be used.

Water

I Important: This washing machine

MUST only be connected to a cold

water supply.

a: Connect the water inlet hose, the angled

connection attaches to the water inlet on the

back of the washing machine. (7)

b: The straight connection attaches to the

water supply valve. (8)

c: Ensure all seals are in place before

connecting.

Important: Only tighten the hose connection

nut by hand - do not overtighten.

Important: The height of the top of

the curve in the drain hose MUST be

between 60 - 100cm from the

floor.(9)

Important: The end of the water drain hose

may be fitted directly to the waste water outlet

hole or a special apparatus mounted on the

outlet bracket of the wash-stand.

Important: Never attempt to extend the water

drain hose by adding extra parts.

time

Let’s get started

1 2

2- Programme Knob

With the programme knob, you can select the programme with which you desire to wash your clothes. You can select programmes by turning the programme dial in both directions. You must be careful that the adjustment sign of the programme dial is exactly on the programme you want to select. If you move the programme dial to 0 (off) position, while your machine is running, your programme will be cancelled.

Note: If you want to activate an additional

function after the machine has started washing, press the additional function button that you want to use. If the additional function selected can still be used at that programme stage, the LED of the function button will be turned on and the function will be added to the programme. If the LED is not turned on, the function selected is not possible at that stage of the current programme and will not be activated.

3- Electronic Display

On the electronic display, you may view washing water temperature, spinning revolution speed of your machine, when your machine will finish washing, the auxiliary functions you have selected and at what stage the programme you have chosen is,

( prewash/wash, rinsing, spinning).

Furthermore, the electronic display will warn you by means of fault symbols on the display when a fault occurs on your machine and notify you of the completion of the washing programme by showing “END” on the display as soon as the washing programme you have selected has finished.

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions, or online at www.bush-support.com If you still require further assistance, call one of our experts on 0345 257 7271. section of these instructions, or online at www.bush-support.com If you still require further assistance, call one of our experts on 0345 257 7271.