Bush W50B1A401L Instruction manual

246/3487

2-3

4

5-7

5
5
5
6
7

8-17

8
8-9
10
11

12-14
15

16-17

18

18

Specification

19

19

DWFS146W

20

21

22

DWF S146W

9

10

9 Inlet pipe connector
10 Drain pipe connector

246/3487

4

50

567

2kg

500ml

Salt consumption

When you run the dishwasher, the water
softener will be full of water. Therefore,
adding softening salt should always be
done immediately before you start the
unit. Check the salt level to ensure it is
enough before starting one of the
complete washing programs and ensure
500ml of water has been added.

2

1

2

8

The unit is equipped with a function that you
can adjust the frequency to release the salt to
the water softener. This is further to the
selector on the salt container. The default
setting is H4.

IMPORTANT :

YOU SHOULD SET THIS VALUE
ACCORDING TO THE WATER HARDNESS
OF YOUR AREA BEFORE THE 1 USE.

ST

INCORRECT SETTING WILL AFFECT THE
RESULT OF THE WASHING. ONCE YOU
HAVE SET THE SETTING, THE UNIT WILL
REMEMBER THE LAST SETTING.

Adjustment for value

1. Find out the hardness value for your tap
water or your area.

2. Compare with the table below to find out the
required value for setting to this unit.
Table

Value f or
selec tin g in
this un it

Frequ enc y to
relea se sa lt

Never

Seldo m

Somet ime s

Somet ime s

Often
Often

Usual ly

Alway s

3. Close the door

4. Press ON/OFF button to turn on the
machine

5. Press Delay button and Program button at
the same time and hold for 5 seconds. The
machine will sound once. It displays H4.You
can release both buttons.

6. Continue to press Delay button to select the
desire value, i.e. H5, H6 or H7 is for serious
water hardness area region like UK.

7. Once the desire value is selected, press
Program button to confirm. Then the setting
has been stored and it will get back to the
normal standby status.

Hint : For easy setting on this value, it is
suggested to select H7. Then you can control
the salt consumption by turning the selector
on the salt container.

9

10

30

11

appliance

12

appliance

Cutlery tray

13

!

WA RN ING !

Do not le t any ite m
ext en d th ro ug h bo tt om

appliance

14

Standard daily c ycle
for normally soi led loads,
such as pots, plat es, glasses.

15

3.

4.

5. Continue to p ress "progr am" button to select the desired "wash cycle". (See th e section entitled
“ Wash Cycle Table”). Press "start/pause" button to start the program .

1.

Close the door,press the power button.

2.

Then turn it on by press "power" button again,

table

Press "start/pause" button to start the washing program.

NOTE: Delay function:
After selecting the wash cycle program, you can set the desired delay time by pressing the delay
button. The dishwasher will start operation after the

It can be set up to 24 hour delay time.

selected delay time is elapsed.

NOTE: Child safety lock function
To lock, press child lock button and 3 in 1 button at same time and hold for at least 3 seconds.
The child lock indicator will flash 6 times and then illuminate.
To unlock, press child lock button and 3 in 1 button at the same time and hold for at least 3
seconds. The unit will get back to normal standby status and the child lock indicator will switch off.

NOTE : "3 in1" function
"3 in 1" is a special designed program to use the 3 in 1 dishwasher tablet. You can buy the tablet
in the high street. Add the tablet into the detergent box and do not need to fill the salt & rinse-aid.
Press once on the 3 in 1 button and the indicator will illuminate. Then select the washing program
as usual. To have the best result, it is strong suggested to add salt to the salt container for water
softener. (see waster softener section)

If you open the door when washing, the machine pauses and sounds warning alarm, it displays E1.

Under different status, the program indicator will light in different combination:

16

Program End

1.When the washing program is finished, it will sound 6 times and displays ''- - ''.

2. Open the door and remove all the dishes.

3.Turn off the unit by pressing the Power switch. Then close the door.

4. Shut down the water supply after using.

Special attention :
If all the indicator lights start to glimmer, the machine should be out of order. Please turn off the
power and shut down the water supply. Then call the customer helpline.
Warning :
It is dangerous and not recommend to open the door during the washing operation. The hot water
may come out and scald you while the door is open during the operation.

17

18

Error

19

Technical specifications (according to EU Directive 1059/2010)

Brand

Model

Capacity

Energy efficiency class

Annual energy consumption

Energy consumption of the standard cleaning cycle

Power consumption of off-mode/left-on mode

Annual water consumption

Drying efficiency class

Standard cleaning cycle

1

2

A++

0.93 kWh

0.35W/0.9W

3

4

5

Program time for the standard cleaning cycle

Noise level

Freestanding/Built-in

Dimension

Freestanding

Power consumption

Rated voltage

BUSH

DWFS146W

14 settings

266kWh

3080 litre

A

Eco

178 min

45 dB(A) re 1 pW

W600xD600xH845

1850W

220-240V~50Hz

Water pressure(flow pressure)

NOTE

1

A+++(most efficiency) to D(least efficiency)

2

Energy consumption “266"kWh per year, based on 280 standard cleaning cycle using cold water fill
and the consumption of the low power nodes. Actual energy consumption will depend on how the
appliance is used.

3

Water consumption “3080" litres per year, based on 280 standard cleaning cycle. Actual water
consumption will depend on how the appliance is used.

4

A(most efficiency) to G(least efficiency)

5

This program is suitable for cleaning normally soiled tableware, and that it is the most efficient
programme in terms of its combined energy and water consumption for that type of tableware.

The above values have been measured in accordance with standards under specified operating
conditions amount of detegent,etc.

0.04-1 MPa

20

21

Argos Ltd