BURY ChargingCradle
Universal
Installation manual
BURY ChargingCradle Universal
Index
Introductory information 2
1. General 2
2. Security guidelines 2
Installation of the system 4
3. Scope of supply 4
4. Installation of the system 6
5. Installing the BURY ChargingCradle Universal in the vehicle 9
6. Inserting and removing the mobile phone 12
7. Rotating the cradle 14
8. Charging the phone in the cradle 15
9. Initialising the BURY ChargingCradle Universal 15
Further information 16
10. Service 16
11. Appropriate use of this system 17
12. Approvals and declaration of conformity 17
2
Introductory information
1. General
Dear customer,
Congratulations on purchasing a BURY telephone holder for cellular phones. You have chosen a high
quality product that is extremely easy to use. Please read the installation manual carefully so that you
can fully enjoy your BURY product.
If you have any further questions concerning installation or operation of this device, please contact your
dealer. He will be happy to give you reliable advice. You can also contact our hotline. Our phone and fax
numbers are listed in the chapter Service.
Have a good trip!
2. Security guidelines
Power supply
The power usage of the cradle has been designed for the use in vehicles
with an on-board supply syst em of 12 volts (passen ge r c ar). If yo u i nten d
to install the device in a vehicle with an on-board supply system
of 24 volts (lorry), please use a voltage converter. If you have queries
regarding this subject, please contact our hotline.
Position
Install the cradle in the vehicle so that your field of vision is not impaired
and the components are not mounted in the impact zone of the passenger compartment or in the airbag inflation zones. Very important: please
observe the car manufacturer’s information (operating manual) as regards “accessories”. If in doubt, please contact a specialist workshop to
get information on the correct position for installation in the vehicle.
Intended use
We shall not be liable for damages or malfunctions due to improper use
of the hands-free system. Therefore, do not expose the device to moisture, extreme temperatures or shocks and follow the procedure described in the installation manual carefully.
3
Use while driving
Operate the smartphone in the holder only when the situation allows it and when you do not endanger,
harm, constrain, or annoy other road users. The volume of the smartphone has to be set in a way that
exterior noise is still audible.
Important:
The driver is ultimately responsible for the safe operation and control of their vehicle X
at all times.
Research indicates that there is a risk to safety when the driver of a motor vehicle is X
distracted and using a mobile phone while driving can be a distraction.
The manufacturer strongly recommends that you use a hands-free solution for a phone X
call when driving.
Faults
Do not use the telephone holder if you detect or assume a defect. In this case, contact a BURY specialised dealer or our hotline. Improper repairs can be dangerous for you. Therefore, only skilled personnel
may perform inspections.
4
3. Scope of supply
Installation of the system
98
10
5
The BURY ChargingCradle Universal is supplied with different combinations of components, depending
on the sales regions (countries). The operating manual refers to all versions.
Description of the components:
1) Cradle
2) Set of tips for specific mobile phone models
3) Dash Mount Adapter for installation on the dashboard or console
4) Little Flat antenna with fakra-connection
5) Charging cable (Micro USB)
6) Charging cable (Mini-USB) for electronic box or charger
7) Installation manual
Accessories - available separately / including, if applicable:
8) Five (different) charging cables (Micro-USB, Mini-USB, Nokia Pin 2mm, iPhone, Sony Ericsson)
9) Window Mount
10) Power supply - via electronic box or charger
Note:
If certain components are added or omitted you will receive the corresponding X
information on a separate enclosure.
Connection options:
Power supply
1. Connection of the mobile phone‘s charging cable (also possible in connection 2).
2. Connection of the charger‘s charging cable.
The conduction of the power supply occurs via the electronic box or the charger.
1 2
Loading...