Buffalo l310, l371, s007, s047, s077 User Manual

Bains Marie

Models:

L310/L371/S007/S047/S077/S377/S378

Table of Contents

Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Pack Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Maintaining Water Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Emptying the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cleaning, Care & Maintenance . . . . . . . . . . . . . . . . . . . . . . 2

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Spares List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Circuit Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Tips

• Position on a flat, stable surface.

• A service agent/qualified technician should carry out installation and any repairs if required. Do not
remove any components on this product.

• Consult Local and National Standards to comply with the following:

• Health and Safety at Work Legislation

• BS EN Codes of Practice

• Fire Precautions

• IEE Wiring Regulations

• Building Regulations

• DO NOT immerse the appliance in water, or use jet/pressure washers to clean it.

• DO NOT touch hot surfaces with bare hands. Always use the handles/protective gl oves.

• DO NOT overfill the appliance. Keep the wat er le vel below the ‘MAX’ level.

• DO NOT allow the water level to drop below the ‘MIN ’ level during operation.

• DO NOT move the appliance when it contains hot liquid.

• DO NOT use the appliance for anything other than its intended use.

• Always switch off and disconnect the power supply to t he appliance when not in use.

• Not suitable for outdoor use.

• Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of
local authorities.

• If the power cord is damaged, it must be replaced by an BUFFALO agent or a recommended qualified
technician in order to avoid a hazard.

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of
this appliance will provide the best possible performance from your BUFFALO product.

Pack Contents

The following is included:

•BUFFALO Bains Marie

• Pans 2 x 1/3 and 2 x 1/6 (S007/S047 only)

• Support bars (S007/S047 only)

BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are
supplied fully functional and free of damage.

Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

• 6 litre pots x 2 (S077 only)

• Instruction manual

1

Operation

70

60

80

50

90

40

Power Switch

1. Connect the appliance to the power supply.

2. Fill the tank with water to a level between the ‘MIN’ and ‘MAX’ marks on the inside of the tank.

Power Indicator Light Thermostat Dial

Note: BUFFALO recommend that fresh water be used each time the appliance is used.

3. Switch the power switch to the On position [I]. The red power indicator light will turn on.

4. Turn the thermostat to the highest setting (90°C) to heat-up the app l iance.

5. Reduce the heat setting once the appliance has heated the water. An operating temperature of

75°C - 80°C is sufficient.

Note: Do not allow the water to drop below the ‘MIN’ level during operation. Severe
damage to the heating element could result.

Maintaining Water Levels

It is important to regularly check the water lev el in the Bains Marie tank.
Always keep the water level above the ‘MIN’ mark on the inside of the tank during operation.
Damage to the heating element can occur if the tank boils dry and the element may have to be replaced.
This is not covered by the BUFFALO warranty.

Emptying the Appliance

Note: Always switch the appliance off allow the water to cool before emptying.

Use a suitable vessel to remove the water from the appliance.
L310/S047 Only - Turn on the tap to drain the water. Ensure a suitable container is used to collect the

water.

Cleaning, Care & Maintenance

Note: Always switch off and disconnect the appliance from the power supply before
cleaning.

Always allow the appliance to cool before emptying or cleaning.

• Wipe down the exterior of the appliance with a damp cloth.

• Some cleaning agents may cause damage when used for a prolonged period on stainless steel. Use a
suitable stainless steel cleaner such as Sanizap Stainless Steel Cleaner (Product code: U386).

• Dry the exterior thoroughly.

• Wash all removable parts in warm, soapy water.

2

Tr ou bl es h oo t in g

Fault Probable Cause Action

The unit is not switched on Check the unit is plugged in correctly

Plug and lead are damaged Call BUFFALO agent or qualified

Fuse in the plug has blown Replace the plug fuse

The unit is not working

Power supply Check power supply
Internal wiring fault Call BUFFALO agent or qualified

The thermal cut out switch has
tripped

The thermostat has not been
set correctly

The heating element has failed Call BUFFALO agent or qualified

Technical Specifications

and switched on

technician

technician
Call BUFFALO agent or qualified

technician
Set the thermostat to a higher

temperature

technician

Model Voltage Power Current Weight

L310
S047 10.8kg 275 x 340 x 615
S007 10.8kg 275 x 340 x 615
S377 10.8kg 275 x 340 x 615
L371 10.8kg 270 x 340 x 615
S378 10.8kg 270 x 340 x 615
S077 11.25kg 324 x 340 x 565

230V 50Hz 1500W 6.6A

10.8kg 270 x 340 x 615

Dimensions

h x w x d mm

3

Exploded Diagram

8

7

Spares List

6

1

5

4

3

2

Number Description Spare Code

1 Heating Element N441
2 Thermostat Dial N433
3 Thermostat N432
4 Indicator Light N430
5 On/Off Switch N431
6 Thermal Cut-out N487
7 Drip Tap* N335
8 Hose* AB826

*(L310/S047 only)

4

Circuit Diagram

Note: This circuit diagram has been provided to assist qualified technicians. Do not
remove any components or service panels on the appliance.

Thermal
Cutting Device

ThermostatMain Switch

L

Indicator
Lamp

Heating
Element

N

E

Electrical Wiring

This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard.
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L

• Neutral wire (coloured blue) to terminal marked N

• Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed, using a dedicated earthing circuit.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency

disconnection being required they must be readily accessible.

Compliance

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and
specifications set by international, independent, and federal authorities.

BUFFALO products have been approved to carry the following s ymb ol:

5

BUFFALO Telephone Helpline: 0845 146 2887

BUFFALO, Fourth Way, Avonmouth, United Kingdom, BS11 8TB