BT Video Baby Monitor 7500 Lightshow Instruction manual

BT Video Baby Monitor 7500 Lightshow

User guide

Contents

Welcome ................................................................. 3

Getting set up ......................................................... 4

Learn about your menu ......................................... 10

Learn about your Parent unit ................................. 12

Learn about your Baby unit ................................... 13

Baby unit (camera) ................................................ 14

Using the Night Light ............................................ 16

Using Lullabies ...................................................... 18

Feed Timer ............................................................ 22

Temperature ......................................................... 24

Cry Alerts .............................................................. 27

Night vision ........................................................... 30

Settings ................................................................ 31

BT Help ................................................................. 33

Help and troubleshooting ...................................... 35

Guarantee and returns ........................................... 37

Using the Lightshow.............................................. 20

Important safety notices

1. Your baby monitor is designed as an aid. It isn’t a substitute for responsible and proper adult supervision.

2. Make sure all cables and units are out of your baby’s reach – at least one metre away.

3. Never cover either unit, put them in moist places or inside the cot, bed or playpen.

4. If you travel abroad, check the voltage on your unit’s plugs match the local power output.

5. Only use the battery supplied for the Parent unit. If you need to replace it, contact our helpdesk.

6. Do not take the product apart. If you need repairs, get in touch with our helpdesk.

7. The Baby unit might get warm after it’s been on for a while. Don’t worry – this is normal, and is perfectly safe.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Welcome

Thanks for buying this BT Baby Monitor. You’ll soon be able to relax knowing you can watch and listen to your baby’s every breath, gurgle and wriggle.

But rst things rst. To get set up, just follow the steps over

the page. Set-up only takes a few minutes.

Then, you can learn all about your monitor and how to use it from page 10.

Need some help? No problem – give us a call on 0808 100 6554*, or go to bt.com/producthelp. Once you’ve set things up, you can tap BT Help on your Parent unit to run through the set-up wizard again.

* Calls made from within the UK mainland are free. Mobile and international call costs may vary.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Getting set up

Place the charging dock near a power socket in the room where you’re going to be

monitoring your baby most of the time. (Most people have their charging dock on a bedside table).

Using one of your two micro USB cables, plug one end into the power plug.

When does near become too far?

The maximum range between your Parent and Baby units is about 300 metres outdoors and about 50 metres indoors. Thick walls and doors reduce the

units’ range and aect how

they link to each other.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Getting set up

Remove this tab

and charge batteries

for 5 hours before use.

Plug the other end into the charging dock, then plug the power plug into the power

socket and switch the power on.

Pull the battery tab out of the Parent unit.

Tip

You can also plug the USB cable directly into your Parent unit without needing to use the charging dock.

Tip

You can also charge your Parent unit using other micro USB cables. This can be handy when you’re away from home with your baby.

Tip

If you charge your Parent unit whilst it’s turned

o, the battery icon will

disappear when the unit is fully charged.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Getting set up

Home

Put your Parent unit on the dock to charge for at least ve hours.

You can tell it’s fully charged when the green battery icon on the screen

is solid green.

Important note about batteries

A fully charged Parent unit will last about 6.5 hours with normal use. To speed up charging, charge the Parent unit

when it’s switched o.

You can also charge the Parent unit and use it at the same time, but it’ll charge more slowly and take longer to fully charge. If the Parent unit battery is low with only about 30 minutes’ charge left, you’ll hear an alert tone. If this happens, put the Parent unit back on charge if you want to keep monitoring your baby.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

1-2 Metres

After the Parent unit has charged for ve hours you’re ready to set up your Baby unit

(camera). To get the best performance, place your Baby unit between one and two metres away from your baby. If you like, you can also attach the unit to a wall. See page 35 for how to do this. Make sure there’s enough slack in the power cable so the Baby unit can pan freely.

Getting set up

Tip

Point the Baby unit’s camera to the centre of the mattress or playpen. You

can always adjust this later.

Don’t twist it

Don’t twist your Baby unit by hand to change the camera view or angle. You might damage it.

Important note

The Baby unit might get warm after it’s been on for a while. Don’t worry – this is normal, and it’s perfectly safe.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Getting set up

Using your other micro USB cable, plug one end into the power plug and the other

end into the Baby unit. Plug the power plug into the power socket and switch the power on.

Press and hold the power button for a second or two. The link light will ash green

and the nightlight will light on and o.

Important note about connections

If the Parent and Baby unit lose the link or connection between them, the link

light will ash and the

screen will say the link is lost, and is trying to reconnect. If after 30 seconds there’s still no link, you’ll hear an alert tone from the Parent unit. First, check on your baby and then follow the steps from step 7 again to set up the link again.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Getting set up

Vol.

Mute

Power

Talk

Press the power button to switch on your Parent unit. The Parent and Baby unit will

link automatically and the Baby unit’s link light will turn solid green.

The rst time you switch on your Parent unit, a set-up wizard asks you to set the time

and then shows you all your baby monitor’s features.

If you want, you can skip through the set-up wizard by tapping the screen or tapping

Exit, when shown.

When you exit the set-up wizard, the Parent unit will show you the live view from the

Baby unit and you’re all set up!

Tip

If you ever want to watch the set-up wizard again, tap Menu and then BT Help, then Introduction.

Need some help? Call 0808 100 6554* or go to bt.com/producthelp

Learn about your menu

Using your baby monitor

This will show the strength of your connection between the Parent and Baby unit.

Quick access menu for Night Light, Lullabies and Lightshow

The temperature of the room the Baby unit is in.

Name your camera or pair additional cameras.

How do I leave the menu?

Press .

This is on the left of the screen and shows

you the level of noise in your baby’s room.

Signal strength