BT Video Baby Monitor 3000 Instruction manual

Oﬀ

and aect how they link to each other.

indoors. Thick walls and doors reduce the units’ range units is about 250 metres outdoors and about 50 metres The maximum range between your Parent and Baby

What’s the range?

they are now ready to use. The Parent and Baby unit are automatically linked so

Parent unit on. Press the button and hold for 2 seconds to turn the

feedback sounds.

from the Baby unit. Any closer and you might get audio

Before you do, move the Parent unit at least one metre

switch it on.

After the Parent unit has charged for 12 hours you can

turn it o while it’s charging.

extra length and securing it. Keep the power cord out of baby’s reach by looping any

Tip

up to turn it on.

button on the side of the Baby unit

Slide the

To charge the Parent unit in the shortest amount of time,

short time. minutes to charge enough for you to use it for a When the battery gets very low, it’ll take about 30

used it for a long time, it’ll take 12 hours to fully charge.

The rst time you use the Parent unit, or if you haven’t

Tip

get in touch with our helpdesk.

5. Do not take the product apart. If you need repairs,

plugs match the local power output.

4. If you travel abroad, check the voltage on your unit’s

inside the cot, bed or playpen.

3. Never cover either unit, put them in moist places or

reach – at least one metre away.

2. Make sure all cables and units are out of your baby’s

Leave to charge for 12 hours.

Link

adult supervision. It isn’t a substitute for responsible and proper

1. Your baby monitor is designed as just an aid.

Important safety notices

mains power socket and switch the socket on.

Plug the cable into the Baby unit, then plug it into the

your baby. the time. It should also be at least one metre away from where you’re going to be monitoring your baby most of

Place the Baby unit near a power socket in the room

mains power socket and switch the socket on.

Plug the cable into the Parent unit, then plug it into the

or give us a call on 0808 100 6554 opposite. If you need any help, go to bt.com/producthelp

But rst things rst. To get set up, just follow the steps

for your baby’s every breath, gurgle and wriggle. be able to relax knowing you can watch and listen Thanks for buying a BT Baby Monitor. You’ll soon

Troubleshooting

My Parent/Baby unit isn’t working. What should I do?

Check that:

power cables are plugged in and switched on at the

wallsocket

the Baby unit is plugged in and the Parent unit battery

is fully charged (for 12 hours)

both units are turned on

the Parent unit isn’t too far from the Baby unit (large

obstructions or other electrical devices might aect the

signal between the Parent and Baby unit).

unplugging the power cables, waiting about 15 seconds,

and then plugging them back in can help.

My Parent/Baby unit is making a high-pitched noise.

Whatshould I do?

The units might be too close together. Make sure they’re at least one metre apart, even when you’re using the

button.

Why is my Parent unit beeping?

The Parent unit beeps when:

• the Baby unit is turned o

• the units are too far apart – try moving them closer together (but not closer than one metre)

• the battery in the Parent unit isn’t charged – try charging it for 12 hours

• Other electronic items, like TVs and mobile phones, are causing interference – try moving the Baby unit away from things like that.

Why is the Parent unit not making any sounds even though there’s noise coming from my baby’s room?

• the Parent unit might not be fully charged – make sure it’s charged (for 12 hours).

• the speaker volume might be switched o.

• the Parent unit might be out of range of the Baby unit – try moving it closer (but not closer than one metre).

• large obstructions or other electrical devices might

be aecting the signal between the Parent and Baby

units). Try moving the Baby unit away from obstructions, including electrical appliances like TVs or mobile phones.

Need some help?

Frequently asked questions are available online.

bt.com/producthelp

If you cannot nd the answer to your question online, call our free Helpline. Our dedicated advisors are more likely to be able to help you than the retailer where you bought your baby monitor.

0808 100 6554*

This user guide is also available in other formats: large

print, Braille and audio CD. Call the helpline for a copy.

* Calls made from within the UK mainland network are free.

Mobile and international call costs may vary.

General information

Guarantee

Your Video Baby Monitor 3000 is

guaranteed for a period of 24 months from the date of purchase.

Subject to the terms listed below, the

guarantee will provide for the repair of, or at BT’s or its agent’s discretion the option to replace the Video Baby Monitor 3000, or any component thereof, which

is identied as faulty or below standard,

or as a result of inferior workmanship or materials. Products over 28 days old from the date of purchase may be replaced with a refurbished or repaired product.

The conditions of this guarantee are:

• The guarantee shall only apply to defects that occur within the 24 month guarantee period.

• Proof of purchase is required.

• The equipment is returned to BT or its agent as instructed.

This guarantee does not cover any faults or defects caused by accidents, misuse, fair wear and tear, neglect, tampering with the equipment, or any attempt at

adjustment or repair other than through

approved agents.

This guarantee does not aect your statutory rights.

To nd out what to do, if your monitor is

in or outside of the 24 month guarantee, go to bt.com/producthelp

Registered Oce: 81 Newgate Street, London EC1A 7AJ. Registered in England No. 1800000 Designed and produced by The Art & Design Partnership (ADP). Printed in China / Issue 5 / ADP12-17

How to recycle your equipment

The symbol shown here and on the product means that the product is classed as electrical or electronic equipment, so DO NOT put it in your normal rubbish bin.

It’s all part of the Waste Electrical and Electronic Equipment (WEEE) Directive to recycle products in the best way – to be kinder to the planet, get rid of dangerous things more safely and bury less rubbish in the ground.

You should contact your retailer or supplier for advice on how to dispose of this product in an environmentally friendly way.

Radio Equipment Directive Declaration of Conformity

Hereby, British Telecommunications plc declares that the radio equipment type BT Video Baby Monitor 3000 (088304) is in compliance with Directive 2014/53/EU.

This device has been evaluated for and shown compliant with European Guidelines when installed and operated with a minimum distance of 16mm between the unit and your body.

The item code for both power supply units is 089009 (BLJ06W050060P1-B).

The full text of the EU declaration of conformity is available at the following internet address: bt.com/producthelp

Radio transmission information

Frequency range 2415.375 –

Max power 89.54mW (19.52dBm)

2471.625MHz

Getting set up

Welcome

Video Baby Monitor 3000 User Guide

Using the Parent unit

Oﬀ

Turn on and o

Press and hold for 2 seconds to turn on and o.

Using the menu

• Press to open the main menu. Scroll through the menu options using and . When the menu option you want is displayed, press . Use or to scroll through the sub menus and press

to select.

• Press to exit the menu and return to the main monitoring screen.

Monitoring volume and mute

There are 8 volume settings.

1. In normal monitor mode (X1), press or to change the volume.

2. Press to conrm.

3. To turn the sound o completely, turn the volume down to 0. will be displayed on top of the screen.

Screen brightness

There are 8 brightness levels. The default is 4.

1. In normal monitor mode (X1), press or to select the brightness level.

2. Press to conrm.

Get to know your Baby unit

Link

Link button

The units are pre-linked.

(Link button used if re-link ever required).

Add camera

Delete camera

View camera

Power socket

Camera

Power on/o

Slide button up to

turn on and slide

down to turn o.

Temperature

Oﬀ

Manual pan and tilt

Gently move

the camera to

adjust the angle.

sensor

Set a reminder

You can set an alert to remind you of something you need to do, for example when your baby’s next feed is due. You can set it for 2, 4 or 6 hours.

1. Press , then press to display and press .

2. Press or to select the reminder time (2H, 4H or 6H), then press to save. The will be displayed on the top right of the screen.

3. To cancel the alert, select .

Set the screen to turn on and o automatically

You can set the screen to turn on by pressing any button. On this

setting, the screen will turn o automatically when no button is

pressed during 1, 3 or 5 minutes.

1. Press , then press to display and press .

2. Press and to select 1, 3 or 5 minutes and press .

3. To turn the screen back on at any time, press any button. If you want to set the screen on all the time, set the screen setting to o .

Turn sound activated screen mode on or o

When set to On, the screen will turn on if noise is detected from the

Baby unit. If it’s set to O, the screen will stay o even if noise is detected. To use this feature, you need to set the standby mode rst

to 1, 3 or 5 minutes as described above.

1. Press , then press to display and press .

2. Press and to select (for On) or (for O) and press .

3. To turn the screen back on at any time, press the .

Lullabies

There are 5 lullabies to choose from or you can play all 5 in sequence.

1. Press , is displayed, press .

2. Press or to choose the lullaby 1-5 or press to play all ve, then press .

3. Press or to select the volume from 1-3 and press to save.

4. To stop the lullaby playing, select .

Talk to your baby

To give your baby some words of comfort, press and hold down on the Parent unit and speak into the Parent unit’s microphone. The icon will be displayed at the bottom right corner. Release the

button when you’ve nished speaking.

Zoom in and out

1. Press , then press to display and press .

2. Press or to select the zoom level (X1 or X2), then press to save.

3. Press to return to the main monitoring screen.

4. Whilst in X2 mode, press , , or to move the image.

5. To adjust the volume or screen brightness when in X2 zoom mode,

press and select the or option and press .

Get to know your Parent unit

Sound level display

LED lights show the level

of sound being detected

from the Baby unit.

Charging/

battery light

Blue when mains

power adapter

is on, red when

battery low.

(Remains green for one minute while charging,

Power on light

Green when Parent

unit turned on.

after the parent unit

is turned o).

Press and hold to turn

the unit on and o.

Press once to switch to

standby mode.

when in the zoom mode (X2).

Press to increase or

decrease the speaker

volume, when in

normal mode (X1).

Press to move up or down

Press to scroll up or down when you’re in the menu.

Press and hold to talk to your baby.

Press to select an option in the menu.

Press to open/exit the main menu.

Microphone

Press to increase or decrease the brightness level, or press to move left or right when in the zoom mode (X2).

Power socket

Speaker

Lift and twist.

Stand

Temperature sensor

The reading from the temperature sensor will be displayed at the top of the Parent unit screen.

To change the temperature display from C to F:

1. Press , then press to display and press .

2. Press or to select °C or °F, then press .

Other screen icon descriptions

Signal strength

Baby unit switched on

Camera identication

number e.g. Camera 1

Sound on

Mute

Battery status (Full battery shown,

scrolling when charging)

Using the Baby unit

Turn on and o

1. Slide the press down to turn O.

Night vision

So that you can see your baby at night, the Baby unit automatically

uses the light from its infrared LED lights to capture images in a dark room. Because of that, it can only show images in black and white. The icon will be displayed at the top of the screen.

button on the side of the unit up to turn On and