Welcome
On
Off
Thanks for buying a BT Baby
Important safety notices
1. Your baby monitor is designed as just an aid.
It isn’t a substitute for responsible and proper
adult supervision.
Video Baby Monitor 5000
User Guide
Monitor. You’ll soon be able to
relax knowing you can watch
and listen for your baby’s every
breath, gurgle and wriggle.
But rst things rst. To get set up, just follow
the steps below. If you need any help,
go to bt.com/producthelp or give us a
call on 0808 100 6554*.
2. Make sure all cables and units are out of your baby’s
reach – at least one metre away.
3. Never cover either unit, put them in moist places or
inside the cot, bed or playpen.
4. If you travel abroad, check the voltage on your unit’s
plugs match the local power output.
5. Do not take the product apart. You can’t change
the battery installed in the Parent unit. If you need
repairs, get in touch with our helpdesk.
Getting set up
1
Plug the cable into the Parent unit, then plug it into the
mains power socket and switch the socket on.
2
Leave to charge for 12 hours.
Tip
The rst time you use the Parent unit, or if you haven’t
used it for a long time, it’ll take 12 hours to fully charge.
The battery life on a single charge lasts for 4 hours.
We recommend you keep the cable plugged into the
mains power socket if you’re going to use for longer than
this or throughout the night.
When the battery gets very low, it’ll take about 30
minutes to charge enough for you to use it for a
short time. To charge the Parent unit in the shortest
amount of time, turn it o while it’s charging.
3
Place the Baby unit near a power socket in the room
where you’re going to be monitoring your baby most of
the time. It should also be at least one metre away from
your baby.
4
Plug the cable into the Baby unit, then plug it into the
mains power socket and switch the socket on.
Link
5
Slide the
turn it on.
Tip
Keep the power cord out of baby’s reach by looping any
extra length and securing it.
button on the side of the Baby unit up to
6
After the Parent unit has charged for 12 hours you can
switch it on.
Before you do, move the Parent unit at least one metre
from the Baby unit. Any closer and you might get audio
feedback sounds.
Press the button and hold for 2 seconds to turn the
Parent unit on.
The Parent and Baby unit are automatically linked so
they are now ready to use.
What’s the range?
The maximum range between your Parent and Baby
units is about 250 metres outdoors and about 50 metres
indoors. Thick walls and doors reduce the units’ range
and aect how they link to each other.
Using the Parent unit
Menu
Menu
Menu
Turn on and o
Press and hold
for 2 seconds
Using the menu
• Press to open the main menu. Scroll through the
menu options using and . When the menu
option you want is displayed, press . Use or
to scroll through the sub menus and press to select.
• Press to exit the menu and return to the main
monitoring screen.
Monitoring volume and mute
There are 8 volume settings. The default is 4.
1. In monitor mode, press or to change the volume.
2. Press to conrm.
3. To turn the sound o completely, turn the volume down
to 0. will be displayed on top of the screen.
to turn on and o.
Get to know your Baby unit
Power socket
Link
Camera
Set a reminder
You can set an alert to remind you of something you need
to do, for example when your baby’s next feed is due. You
can set it for 2, 4 or 6 hours.
1. Press , then press to display and press .
2. Press or to select the reminder time (2H, 4H or
6H), then press to save. The will be displayed on
the top right of the screen.
3. To cancel the alert, select .
Temperature
On
Off
sensor
Set the screen to turn on and o automatically
You can set the screen to turn on by pressing any button.
On this setting, the screen will turn o automatically
when no button is pressed during 1, 3 or 5 minutes.
1. Press , then press to display and press .
2. Press and to select 1, 3 or 5 minutes and
press .
3. To turn the screen back on at any time, press any button.
Turn sound activated screen mode on or o
Screen brightness
There are 8 brightness levels. The default is 4.
1. In monitor mode, press or to select the
brightness level.
2. Press to conrm.
Lullabies
There are 5 lullabies to choose from or you can play all
5 in sequence.
1. Press , is displayed, press .
2. Press or to choose the lullaby 1-5 or press to
play all ve, then press .
3. Press or to select the volume from 1-3 and
press to save.
4. To stop the lullaby playing, select .
Talk to your baby
To give your baby some words of comfort, press and hold
down on the Parent unit and speak into the Parent
unit’s microphone. The icon will be displayed at the
bottom right corner. Release the button when you’ve
nished speaking.
Pan/tilt and Zoom in/out
• To enter/exit the pan/tilt mode, press
tilt mode, press , , , to move the image.
• To enter zoom mode, press , then press arrow
to display and press
select the zoom level and press
button to exit the menu.
OK
. Then press or to
OK
. When in Pan/
OK
. Then press the
Link button
The units are pre-linked.
(Link button used if re-link ever required).
Get to know your Parent unit
Sound level display
LED lights show the level
of sound being detected
from the Baby unit.
Charging/
battery light
Blue when mains
power adapter
is on, red when
battery low.
Green when Parent unit
Power on light
turned on. (Remains
green for one minute
while charging, after
the Parent unit is
turned o).
Press and hold to turn
the unit on and o.
Press once to switch to
standby mode.
Press to scroll up or
down when you’re
in the menu.
Press to increase
or decrease the
speaker volume.
Press and hold to
talk to your baby.
Press to select
an option in
the menu.
Press to enter
pan and tilt
mode, then
use the arrows
to move
the camera.
Press to
open/exit the
main menu.
Microphone
Press to move
left or right in the
menu or to increase
or decrease the
brightness level.
Power on/o
Slide button up
to turn on and down
to turn o.
Speaker
Power socket
Stand
Lift and twist.
When set to On, the screen will turn on if noise is
detected from the Baby unit. If it’s set to O, the screen
will stay o even if noise is detected. To use this feature,
you need to set the standby mode rst to 1, 3 or 5
minutes as described above.
1. Press , then press to display and press .
2. Press and to select (for On) or (for O)
and press .
3. To turn the screen back on at any time, press the .
Temperature sensor
The reading from the temperature sensor will be
displayed at the top of the Parent unit screen.
To change the temperature display from C to F:
1. Press , then press to display and press .
2. Press or to select °C or °F, then press .
Using the Baby unit
Turn on and o
Off
1. Slide the
up to turn on and down to turn o.
Night vision
So that you can see your baby at night, the Baby unit
automatically uses the light from its infrared LED lights
to capture images in a dark room. Because of that, it can
only show images in black and white.
The icon will be displayed at the top of the screen.
On
button on the side of the Baby unit
Troubleshooting
My Parent/Baby unit isn’t working. What should I do?
Check that:
1
power cables are plugged in and switched on at the
wallsocket
2
the Baby unit is plugged in and the Parent unit battery
is fully charged (for 12 hours)
3
both units are turned on
4
the Parent unit isn’t too far from the Baby unit (large
obstructions or other electrical devices might aect the
signal between the Parent and Baby unit).
5
unplugging the power cables, waiting about 15 seconds,
and then plugging them back in can help.
My Parent/Baby unit is making a high-pitched noise.
Whatshould I do?
The units might be too close together. Make sure they’re
at least one metre apart, even when you’re using the
button.
Why is my Parent unit beeping?
The Parent unit beeps when:
• the Baby unit is turned o
• the units are too far apart – try moving them closer
together (but not closer than one metre)
• the battery in the Parent unit isn’t charged – try charging
it for 12 hours
• Other electronic items, like TVs and mobile phones, are
causing interference – try moving the Baby unit away
from things like that.
Why is the Parent unit not making any sounds even
though there’s noise coming from my baby’s room?
• the Parent unit might not be fully charged – make sure
it’s charged (for 12 hours).
• the speaker volume might be switched o.
• the Parent unit might be out of range of the Baby unit –
try moving it closer (but not closer than one metre).
• large obstructions or other electrical devices might
be aecting the signal between the Parent and Baby
units). Try moving the Baby unit away from obstructions,
including electrical appliances like TVs or mobile phones.
Need some help?
Frequently asked questions are available online.
bt.com/producthelp
If you cannot nd the answer to your question online,
call our free Helpline. Our dedicated advisors are more
likely to be able to help you than the retailer where you
bought your baby monitor.
0808 100 6554*
This user guide is also available in other formats: large
print, Braille and audio CD. Call the helpline for a copy.
* Calls made from within the UK mainland network are free.
Mobile and international call costs may vary.
General information
Guarantee
Your Video Baby Monitor 5000 is
guaranteed for a period of 24 months from
the date of purchase.
Subject to the terms listed below, the
guarantee will provide for the repair of, or
at BT’s or its agent’s discretion the option
to replace the Video Baby Monitor 5000,
or any component thereof, which is
identified as faulty or below standard, or
as a result of inferior workmanship or
materials. Products over 28 days old
from the date of purchase may be
replaced with a refurbished or repaired
product.
The conditions of this guarantee are:
• The guarantee shall only apply to
defects that occur within the 24
month guarantee period.
•
Proof of purchase is required.
• The equipment is returned to BT or its
agent as instructed.
This guarantee does not cover any faults
or defects caused by accidents, misuse,
fair wear and tear, neglect, tampering
with the equipment, or any attempt at
adjustment or repair other than through
approved agents.
This guarantee does not aect your
statutory rights.
To find out what to do, if your monitor is
in or outside of the 24 month
guarantee, go to bt.com/producthelp
© British Telecommunications plc 2017.
Registered Office: 81 Newgate Street, London EC1A 7AJ. Registered in England No. 1800000
Designed and produced by The Art & Design Partnership (ADP). Printed in China / Issue 1 / ADP04-17
How to recycle your equipment
The symbol shown here and on the
product means that the product is
classed as electrical or electronic
equipment, so DO NOT put it in
your normal rubbish bin.
It’s all part of the Waste Electrical and
Electronic Equipment (WEEE) Directive to
recycle products in the best way – to be
kinder to the planet, get rid of dangerous
things more safely and bury less rubbish
in the ground.
You should contact your retailer or
supplier for advice on how to dispose
of this product in an environmentally
friendly way.
R&TTE Directive &
Declaration of Conformity
This product is intended for use
within the UK.
This equipment complies with the
essential requirements for the Radio
Equipment and Telecommunications
Terminal Equipment Directive
(1999/5/EC).
For a copy of the Declaration
of Conformity please refer to
bt.com/producthelp
Loading...