Bryan Boilers CLM-300-W-GI, CLM-90, CLM-120, CLM-150, CLM-180 Brochure & Specs

Bryan “Flexible Water Tube”

CLM Series

Steam & Water Boilers

900,000 to 3,000,000 BTUH

Atmospheric gas fi red

Form No. 1920

(Rev. 02/08)

BRYAN® BOILERS

Steam Boiler

CLM-150-S150-GI

Water Boiler

CLM-300-W-GI

Originators of the “Flexible Water Tube” design

High effi ciency hot water and steam boilers
for commercial and industrial applications

Bryan fl exible tube boilers are ideally suited for both
hot water and steam space heating systems as well
as either high or low pressure process steam. In a
range of sizes from 900,000 to 3,000,000 BTUH in­put, Bryan CLM series fl exible tube boilers are ideal
for many commercial, institutional and industrial
applications. These include healthcare facilities;
schools; apartments; churches; offi ce buildings;
correctional facilities; airports; sewage treatment
plants; golf, tennis and fi tness clubs. Hospitals,
dairies, restaurants, laundries, dry cleaners, food
processing, tire recapping and metal plating are just
a few of the many applications.
All Bryan boilers are built in accor­dance with the requirements of the ASME
Boiler and Pressure Vessel Code.

Effi cient “Flexible Water Tube”
design

The Bryan bent water tube provides rapid
internal circulation — for maximum heat
transfer and operating effi ciency.

Easily replaceable tubes

Tubes are easily removable and replaceable without
welding or rolling. Little service space is required.

No “Thermal Shock”

The fl exibility of the bent water tube design elimi­nates all possible damage from "Thermal Shock" and
from stresses caused by poor or unequal internal
circulation. This is particularly important with forced
hot water heating systems designed for higher tem­peratures and greater temperature drops.

Steam Boilers: Section IV or I

Steam release area

Large, full-size steam drum provides for dry steam
and stable water level.

High or low pressure construction

Boiler is constructed as standard for 15 psi or 150
psi maximum working pressure. Also available for
higher pressures to 300 psi.

Water Boilers: Section IV

High or low pressure construction

Boiler is constructed as standard for
160 psi maximum working pressure at
230°F operating temperature and 250°F
design temperature. Also available for
higher pressures to 250 psi, at 285°F
operating temperature and 300°F design
temperature.

Natural internal circulation

The water tube design and the large
downcomer legs provide adequate internal circula­tion without concern over exterior pumping condi­tions. Low pressure drop through boiler.

Compact — minimum fl oor space

Requires less floor space than most boilers,
minimum boiler room size. Since the tubes can be
removed from one side, the boilers are available
with right or left hand construction for common tube
removal, further minimizing space needs.
Shipped completely assembled and wired. Units
can also be shipped "Knocked Down" for on-site
assembly.

Bryan CLM Series Boiler Specifi cations

NOMINAL OUTPUT STEAM HEATING APPROX.

BOILER INPUT
MODEL MBH (KW)

CLM-90 900 (264) 720 (211) 21 (206) 742 (337) 110 (10.2) 1,450 (658)
CLM-120 1,200 (352) 960 (281) 29 (284) 990 (449) 145 (13.5) 1,750 (794)
CLM-150 1,500 (440) 1,200 (352) 36 (353) 1,237 (561) 180 (16.7) 2,050 (930)
CLM-180 1,800 (527) 1,440 (422) 43 (421) 1,485 (674) 215 (20.0) 2,350 (1,066)
CLM-210 2,100 (615) 1,680 (492) 50 (490) 1,732 (786) 251 (23.3) 2,650 (1,202)
CLM-240 2,400 (703) 1,920 (563) 57 (559) 1,979 (898) 287 (26.7) 2,950 (1,338)
CLM-270 2,700 (791) 2,160 (633) 64 (627) 2,227 (1,010) 322 (29.9) 3,500 (1,588)
CLM-300 3,000 (879) 2,400 (703) 72 (706) 2,474 (1,122) 360 (33.5) 3,950 (1,792)

NOTES: * Lbs. steam per hour from and at 212°F.

MBH (KW) BHP LBS/HR* SQ. FT. (M²) LBS. (KG)

OUTPUT SURFACE SHIP WT.

Low initial cost, high operating effi ciency
deliver substantial return on investment

• True “fl exible water tube” design guaranteed

shock free

• Longer service life with superior performance

• Full fi ve sq ft of heating

surface per BHP

Quality Construction Features

A. Heavy steel boiler frame, built and stamped

in accordance with the appropriate ASME
boiler code.

B. Large volume water leg downcomers pro-

mote rapid internal circulation, temperature
equalization and effi cient heat transfer.

C. Bryan bent water tubes are fl exible, individu-

ally replaceable without welding or rolling.
Never more than two tube confi gurations.

D. Boiler tube and furnace area access panel:

heavy gauge steel casing with 2" high tem­perature ceramic fi ber and insulation, bolted
and tightly sealed to boiler frame.

E. Jacket access panels make the interior of the boiler

easily accessible for service and inspection.

F. Heavy gauge steel boiler jacket with rust-resistant

zinc coating and attractive enamel fi nish, insulated
with 1½" fi berglass to insure exceptionally cool outer
surface.

G. Minimum sized fl ue vent.

B

D

E

G

L

I

J

C

F

A

K

H

J. Control panel: all controls installed and connected

to terminal strip.

K. Water side or steam side interior accessible for clean-

out and inspection, front and rear openings, upper
and lower drums.

I. All controls, gauges, relief valve(s) are factory installed

and wired and easily accessible for servicing.

Bryan CLM Series Boilers Standard and Optional Equipment

STANDARD EQUIPMENT
FURNISHED

Water Boiler

Combination thermometer and pres­sure gauge, ASME-rated boiler relief
valve, water temperature control
(240°F max. std.), high limit control,
probe LWCO.

Steam Boiler

Steam pressure gauge, steam pres­sure control, combination low water
cutoff and pump control, auxiliary low
water cutoff with manual reset, high
limit pressure control, ASME-rated
boiler relief valve, water glass set.

Atmospheric equipment

Electronic combustion safety control,
automatic operating gas valve, safety
gas valve, pilot solenoid valve, electric

ignition assembly, main manual gas
shut-off valve, pilot shut-off valve,
pilot and main gas pressure regula­tors, barometric draft controller, all
controls installed and wired standard
voltage 120/1/60.

OPTIONAL EQUIPMENT:

1. Manual reset high limit control

2. Manual reset low water cutoff

3. Auxiliary low water cutoff (water)

4. Combination low water cutoff
and feeder

5. Alarm bells or horns

6. UL, CUL, CSD-1, FM, IRI or
other insurance approved

control systems

7. Low fi re start, Hi-Lo or

modulation fi re control

8. Indicating lights, as desired

L. Steam boilers with extra large drum with high steam

release area ensure stable water level and dry steam.

9. Lead-lag systems for two or
more boilers with or without
outdoor reset control

10. Heat exchanger coils for

domestic water

11. Special construction: left hand,
Knocked Down

OPTIONAL
CONSTRUCTION:

Steam boiler

Optional construction to ASME Power
Boiler Code requirements for pressure
exceeding 150 psi to maximum of 300
psi design pressure.

Hot water boiler

Optional construction to ASME
Power Boiler Code requirements for
temperatures exceeding 240°F and/or
pressure exceeding 160 psi to maxi­mum of 285°F operating and 300°F
design temperature and 250 psi.

When ordering, please

specify:

1. Boiler size

2. Supply and return
temperatures required

3. Boiler relief valve setting

4. Type of fuel: natural
or LP, BTU content,
specifi c gravity and
pressure available

5. Optional extra equip­ment or construction

6. Special approvals re­quired (UL, CUL,
CSD-1, FM or IRI)

7. Altitude

G

D

K

I

B

H

LEFT END VIEW FRONT VIEW

PLAN VIEW

RIGHT END VIEW

Barometric

Draft Control

E

L

C

J

F

A

E

G

A

D

E

K

I

B

H

LEFT END VIEW FRONT VIEW

PLAN VIEW

RIGHT END VIEW

Barometric

Draft Control

E

L

C

J

F

Bryan CLM Series Steam & Hot Water Boilers

STEAM BOILER DIMENSIONS in inches (cm)

Boiler Length Gas Train
Model of
Number Jacket

CLM-90-S

CLM-120-S

CLM-150-S

CLM-180-S

CLM-210-S

CLM-240-S

CLM-270-S

CLM-300-S

A B C D E F G H I J K L

Supply

Feed

Nozzle

Width Min. Tube Height Height Floor to

Outside Removal Over Over Flow

Conn.

Jacket Clearance Barometric Jacket Nozzle

1

/2 NPT 383/8 30 8113/16 685/16 711/

Flue Flue Overall

Location Size Length

1

/2 203/4 14 551/2 11/4 NPT 4 FLG 2 NPT 11/2 NPT 383/8 30 785/16 685/16 711/

41

(105.40) (52.70) (35.60) (141.0) (3.18) (10.20) (5.10) (3.81) (97.47) (76.2) (198.90) (173.51) (181.61)

11

/16 2511/32 16 6411/16 11/4 NPT 6 FLG 3 NPT 11/2 NPT 383/8 30 7913/16 685/16 711/

50

(128.74) (64.37) (40.64) (164.30) (3.18) (15.24) (7.62) (3.81) (97.47) (76.2) (202.72) (173.51) (181.61)

11

/16 2927/32 18 7311/16 11/2 NPT 6 FLG 3 NPT 11/2 NPT 383/8 30 805/16 685/16 711/

59

(151.60) (75.80) (45.72) (187.16) (3.81) (15.24) (7.62) (3.81) (97.47) (76.2) (203.99) (173.51) (181.61)

1

/8 349/16 20 831/8 2 NPT 6 FLG 3 NPT 11/2 NPT 383/8 30 8013/16 685/16 711/

69

(175.57) (87.78) (50.80) (211.13) (5.08) (15.24) (7.62) (3.81) (97.47) (76.2) (205.26) (173.51) (181.61)

3

/8 393/16 20 923/8 2 NPT 6 FLG 3 NPT 11/2 NPT 383/8 30 815/16 685/16 711/

78

Connection
(Approx.) 15 psi 150 psi

(199.07) (99.53) (50.80) (234.63) (5.08) (15.24) (7.62) (3.81) (97.47) (76.2) (206.53) (173.51) (181.61)

88 44 20 102 2 NPT 6 FLG 3 NPT 1

(223.52) (111.76) (50.80) (259.08) (5.08) (15.24) (7.62) (3.81) (97.47) (76.2) (207.80) (173.51) (181.61)

97 48

(246.38) (123.19) (50.80) (281.94) (5.08) (15.24) (7.62) (3.81) (97.47) (76.2) (209.07) (173.51) (181.61)

106

1

/2 20 111 2 NPT 6 FLG 3 NPT 11/2 NPT 383/8 30 825/16 685/16 711/

5

/8 533/16 20 1205/8 21/2 NPT 6 FLG 3 NPT 11/2 NPT 383/8 30 8213/16 685/16 711/

(270.82) (135.09) (50.80) (306.38) (6.35) (15.24) (7.62) (3.81) (97.47) (76.2) (210.34) (173.51) (181.61)

2

2

2

2

2

2

2

2

Boiler Length Gas Width Min. Tube Height Height Floor to
Model of
Number Jacket

CLM-90-W

CLM-120-W

CLM-150-W

CLM-180-W

CLM-210-W

CLM-240-W

CLM-270-W

CLM-300-W

Specifi cations subject to change without notice. Consult factory to consult on other boiler options.

Form No. 1920 ©2008 Bryan Steam LLC Printed in USA
28-6833

A B C D E F G H I J K L

Flue Flue Overall

Location Size Length

1

41

/2 203/4 14 551/2 11/

(105.40) (52.70) (35.60) (141.0) (3.18) (7.62) (7.62) (87.31) (76.2) (180.20) (154.78) (165.25)

11

50

/16 255/16 16 6411/16 11/

(128.74) (64.29) (40.64) (164.30) (3.18) (7.62) (7.62) (87.31) (76.2) (183.48) (154.78) (165.25)

11

/16 2913/16 18 7311/16 11/

59

(151.60) (75.72) (45.72) (187.16) (3.81) (7.62) (7.62) (87.31) (76.2) (185.25) (154.78) (165.25)

1

/8 349/16 20 831/8 2

69

(175.57) (87.78) (50.80) (211.13) (5.08) (7.62) (7.62) (87.31) (76.2) (186.52) (154.78) (165.25)

3

/8 393/16 20 923/8 2

78

(199.07) (99.53) (50.80) (234.63) (5.08) (7.62) (7.62) (87.31) (76.2) (187.79) (154.78) (165.25)

88 44 22 102 2

(232.52) (111.76) (55.88) (259.08) (5.08) (7.62) (7.62) (87.31) (76.2) (189.06) (154.78) (165.25)

1

97 48

/2 22 111 2 NPT 3 NPT 3 NPT 345/8 30 7415/16 6015/16 651/

(246.38) (123.19) (55.88) (281.94) (5.08) (7.62) (7.62) (87.31) (76.2) (190.33) (154.78) (165.25)

5

/8 533/16 22 1205/8 21/

106

(270.82) (135.41) (55.88) (306.38) (6.35) (7.62) (7.62) (87.31) (76.2) (191.60) (154.78) (165.25)

WATER BOILER DIMENSIONS in inches (cm)

Train
Connection

NPT 3 NPT 3 NPT 345/8 30 7015/16 6015/16 651/

4

NPT 3 NPT 3 NPT 345/8 30 727/16 60

4

NPT 3 NPT 3 NPT 345/8 30 7215/16 6015/16 651/

2

NPT 3 NPT 3 NPT 345/8 30 737/16 60

NPT 3 NPT 3 NPT 345/8 30 7315/16 6015/16 651/

NPT 3 NPT 3 NPT 345/8 30 747/16 6015/16 651/

NPT 3 NPT 3 NPT 345/8 30 757/16 6015/16 651/

2

Supply Return
Nozzle Nozzle

Outside Removal Over Over Flow
Jacket Clearance Barometric Jacket Nozzle

Bryan Steam LLC — Leaders Since 1916

783 N. Chili Ave., Peru, Indiana 46970 U.S.A.
Phone: [phone] • Internet:www.bryanboilers.com
Fax: [phone]

•

E-mail:[e-mail]

16

115

/16 651/

115

/16 651/

16

16

16

16

16

16

16