Brother LK14 Operation Manual

Operation Manual
Sewing Machine
Video tutorials
1
IMPORTANT SAFETY INSTRUCTIONS
Please read these safety instructions before attempting to use the machine.
DANGER - To reduce the risk of electric shock:
Always unplug the machine from the electrical outlet immediately after using, 1
when cleaning, when making any user servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.
WARNING -
persons.
Always unplug the machine from the electrical outlet when making any 2
adjustments mentioned in the instruction manual:
To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull it out of the electrical outlet. Do not pull on the cord. Plug the machine directly into the electrical outlet. Do not use an extension cord.
included on DVD.
888-X53/X54/X55/X56
To reduce the risk of burns, re, electric shock, or injury to
Always unplug your machine if the power is cut.
Never operate this machine if it has a damaged cord or plug, if it is not working
3
properly, if it has been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or deformation, stop using the machine and immediately unplug the power cord. When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may damage the machine or result in the machine falling, which could cause injuries. When lifting the machine, be careful not to make any sudden or careless movements, otherwise you may injure your back or knees.
Always keep your work area clear:
4
Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot control free from the build up of lint, dust, and loose cloth. Do not store objects on the foot controller. Do not use extension cords. Plug the machine directly into the electrical outlet. Never drop or insert any object into any opening. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. Do not use the machine near a heat source, such as a stove or iron;otherwise,
the machine, power cord or garment being sewn may ignite, resulting in re or an
electric shock. Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine may fall, resulting in injuries.
Special care is required when sewing:
5
Always pay close attention to the needle. Do not use bent or damaged needles.• Keep ngers away from all moving parts. Special care is required around the
machine needle. Do not turn on the machine while pressing down the foot controller. The machine may start unexpectedly and cause personal injury or damage to the machine. Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area. Do not use a damaged or incorrect needle plate, as it could cause the needle to break. Do not push or pull the fabric when sewing, and follow careful instruction when
freehand stitching so that you do not deect the needle and cause it to break.
This machine is not a toy:
6
Your close attention is necessary when the machine is used by or near children. The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of. Never allow children to play with the bag due to the danger of suffocation. Do not use outdoors.
For a longer service life:
7
When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects. Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used. Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.
For repair or adjustment:
8
If the Light unit (light-emitting diode) is damaged, it must be replaced by authorized dealer.
In the event a malfunction occurs or adjustment is required, rst follow the
troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.
XF3656-101
Use this machine only for its intended use as described in this manual.
Use accessories recommended by the manufacturer as contained in this manual.
The contents of this manual and specications of this product are subject to change
without notice.
For additional product information, visit our web site at www.brother.com
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT
In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. Always replace the fuse cover. Never use plugs with the fuse cover omitted. If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.
1
Using Your Sewing Machine
WARNING
Use only regular household electricity for the power source. Using other power sources may
result in re, electric shock, or damage to the machine.
Make sure that the plugs on the power cord are rmly inserted into the electrical outlet and the
power supply jack on the machine.
Do not insert the plug on the power cord into an electrical outlet that is in poor condition. Turn off the main power and remove the plug in the following circumstances:
When you are away from the machine After using the machine When the power fails during use When the machine does not operate correctly due to a bad connection or a disconnection During electrical storms
CAUTION
Use only the power cord included with this machine.
Do not use extension cords or multi-plug adapters with many other appliances plugged in to
them. Fire or electric shock may result.
Do not touch the plug with wet hands. Electric shock may result.
When unplugging the machine, always turn off the main power rst. Always grasp the plug to
remove it from the outlet. Pulling on the cord may damage the cord, or lead to re or electric shock.
Do not allow the power cord to be cut, damaged, modied, forcefully bent, pulled, twisted, or
bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the cord and cause re or electric shock. If the cord or plug is damaged, take the
machine to your authorized dealer for repairs before continuing use.
Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a
re may result.
Connecting plugs
Main power and sewing light switch
Press the power switch toward the “I” mark to turn the main power and sewing light on. Press toward the “O” mark to turn off.
Note
If a power outage occurs while the sewing machine is being operated, turn off the main power and unplug the power supply cord. When restarting the sewing machine, follow the necessary procedure to correctly operate the machine.
(For U.S.A. only)
This appliance has a polarized plug (one blade wider than
the other). To reduce the risk of electric shock, this plug is intended to t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied electrician to install
the proper outlet. Do not modify the plug in any way.
Foot controller
Slower
Faster
Press the foot controller down to start sewing. Take your foot off the foot controller to stop sewing.
CAUTION
Do not allow pieces of cloth and dust to build up on the foot controller. Doing
so could cause a re or an electric shock.
Note (For U.S.A. only)
Foot Controller: Model KD-
1902. This foot controller can be used on the machine with product code 888-X53/X54/ X55/X56. The product code is mentioned on the machine rating plate.
Replacing the needle
CAUTION
Always turn off the machine before you change
the needle. Otherwise, injuries may occur if the
foot controller is accidentally pressed and the machine starts sewing.
Only use sewing machine needles for home
use. Other needles may bend or break and cause injury.
Never sew with a bent needle. A bent needle
will easily break and cause injury.
4
CAUTION
Before replacing the needle, place fabric or paper
under the presser foot to prevent the needle from falling into the hole in the needle plate.
Mark on the wheel points up to rise the needle
Turn the screw counterclockwise
Checking the needle
Parallel space
Level surface
Note
Do not use excessive force
when loosening or tightening the needle clamp screw.
1
5
2
With the at side of the needle
toward the back of the machine, insert the needle until touching this stopper
3
CAUTION
Tighten the needle clamp screw
Make sure you insert the needle until
it touches the stopper, and securely tighten the needle clamp screw with a screwdriver, otherwise the needle may
break or the machine may be damaged.
Changing the presser foot
CAUTION
Always turn off the machine before you change the presser foot. If you leave the power on and
step on the controller, the machine will start and you may be injured.
Always use the correct presser foot for the stitch pattern you have chosen. If you use the wrong
presser foot, the needle may strike the presser foot and bend or break, and may cause injury.
Only use presser feet that have been designed to be used with this machine. Using any other
presser foot may cause accident or injury.
Trial sewing
To sew in reverse, push the reverse sewing lever in as far as possible and hold it in that position while you lightly push the foot controller. To sew forward, release the reverse sewing lever. The machine will then sew forward. The length of reverse
stitches is xed at 2 mm
(1/16 inch).
Reverse sewing lever
Use a piece of fabric and thread that are the same as those used for your project, and check the thread tension and stitch length and width.
1
Changing the sewing direction
Stop the machine with the needle in the fabric at the point where you want to change the sewing direction, and then raise the presser foot lever. Using the needle as a pivot, turn the fabric, lower the presser foot lever, and then continue sewing.
2
Mark on the wheel points up to rise the needle
Sewing thick fabrics
If the fabric does not t
easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position.
CAUTION
If fabric more than 6 mm (15/64 inch) thick is
sewn or if the fabric is pushed with too much
force, the needle may bend or break.
3
Remove the presser foot by pulling it vertically downward.
Press the black button at the back of the presser foot holder to release the presser foot.
Sewing thin fabrics
When sewing thin fabrics, the stitching may become misaligned or the fabric may not feed correctly. If this occurs, place thin paper or stabilizer material under the fabric and sew it together with the fabric.
When you have nished
sewing, tear off any excess paper.
Stabilizer material or paper
4
Sewing stretch fabricsReverse sewing
First, baste the pieces of fabric together, and then sew without stretching the fabric.
Shank
Basting
Presser foot installation orientation
This snaps in to the shank
Stitching cylindrical pieces
1
Slide the at bed
attachment to the left to release it.
Note
When you are nished with free-arm sewing, install the at bed attachment back in its original
position.
CAUTION
If the presser foot is not installed with the
correct orientation, the needle may strike the presser foot, which may bend or break the needle and cause injury.
2
Slide the part that you wish to sew onto the arm, and then sew from the top.
1
Click!
1
2
3
4
5
11
Pull up the spool pin completely
2
3
Turn the power on Hold the end of the thread
4
Wind the thread few times around the bobbin
Lower Threading
CAUTION
Be sure to use the correct bobbin.
11.5mm 7/16”
Actual Size
1
CAUTION
Wind the bobbin properly, or the thread tension may
loosen, and the needle may break.
CAUTION
If the spool is set incorrectly, the thread
may tangle and the needle may break.
5
Pull the thread completely
6
Turn off the power
7
Align the notch to the projection
CAUTION
Slide the bobbin to the right
Hold the bobbin down Pass the thread through the
Do not turn the power on while pressing the foot controller down, otherwise
your may be injured.
slit guide
7 – 10 cm (3-4 inches)
1 cm (1/2 inch)
When the bobbin is full, the bobbin will spin slowly
8
With the end of the thread comes out from the cover toward the rear of the machine
Upper Threading
CAUTION
If the upper threading is not correct, the thread may become tangled or the
needle may bend or break.
2
1
7
Thread the needle from front to back
Turn off the power
Raise the lever to raise the presser foot
8
Hold the end of the upper thread lightly
2
Mark on the wheel points up to rise the needle
3
Pull up the spool pin completely
CAUTION
If the spool is set incorrectly, the thread may
tangle and the needle breaks.
Slowly turn the handwheel toward you (counterclockwise) by hand to lower and then raise the needle
4
Spring
Make sure that the spring in the groove catches the thread
Pull on the upper thread to draw up the lower thread
5
Guide the thread
6
Pull the thread behind the guide above the needle
9
5 cm (2 inches)
Start sewing
– Straight Stitch
3 4
CAUTION
To avoid being injured, watch the needle carefully while you are using the machine. Keep your
hands away from moving parts.
Do not stretch or pull the fabric during sewing, otherwise the needle may be damaged and you
may be injured.
Do not use bent or broken needles, otherwise you may be injured.
Take care that the needle does not hit basting pins or other objects during sewing. The needle
may break and you may be injured.
Always use the correct presser foot. If you use the wrong presser foot, the needle may hit the
presser foot and bend or break and you may be injured.
When you turn the handwheel by hand, always turn it toward you (counterclockwise). Turning it
the other way may cause the thread to tangle and damage the needle or fabric, and you may be
injured.
Do not start sewing without placing the fabric under the presser foot, otherwise the presser foot
may be damaged.
1
Turn the power on
5
CAUTION
Do not turn the power on while pressing the foot controller down, otherwise
your may be injured.
Place the needle to the starting point
2
Mark on the wheel points up
Select a stitch
6
7
Gently press down to start sewing.
Take off your foot to stop sewing.
3
8
4
9
Find more information about your sewing machine
Mark on the wheel points up to rise the needle
Cut the thread
in the included instructional DVD.
Loading...
+ 2 hidden pages