Brother EF-100BATV, EF-100WATV Quick Setup Guide

EF-100WATV/EF-100BATV

Quick Setup

IMPORTANT: Before using this product, make sure you read these instructions
and the safety instructions in the online User’s Guide.

Contents

Connect the USB power cable to the streaming device and fit the device

4

securely inside the projector.

Make sure your projector box includes all of these parts:

You can place the projector on almost any flat surface. See the online User’s
Guide for more information.

Connect the projector

Streaming device

Connect the included Android TV streaming device to your projector. To stream
content, make sure you have an active streaming account and enter your login
information as necessary for each app.

Caution: Do not force the device into the projector; you may damage the
projector and/or the device.

Make sure the device is securely connected as shown below. Pass the USB

5

power cable through the clamp, then close the clamp to secure the cable.

Replace the rear cover of the projector.

6

Note: To connect other streaming devices, see the online User’s Guide for more

information. The projector’s HDMI port does not support MHL®.

Remove the rear cover of the projector.

1

Open the USB power cable clamp.

2

Note: To pair a Bluetooth® speaker or to connect an external speaker or

headphones to your projector, see the online User’s Guide.

External video source

You can connect an external video source with an HDMI cable (not included).

Caution: Do not turn on the video source before connecting it to the projector;
you may damage the projector.

Note: Some external video sources may require an optional HDMI adapter
cable.

Remove the rear cover of the projector.

1

Connect the streaming device to the projector’s HDMI extension cable.

3

Connect an HDMI cable to your video source’s HDMI output port.

2

Connect the other end of the HDMI cable to the projector’s HDMI

3

extension cable.

Pass the HDMI cable through the cable path as shown.

4

Replace the rear cover of the projector.

5

Turn on the projector

Using the projector remote control

Install the batteries as shown (two AAA batteries).

Plug in the projector.

1

Press the power button on the projector or the projector remote

2

control. The power light flashes blue, then stays on.

Microphone

Turn projector on or off

Connect to video-on-

demand apps

Go back to previous

function

Enter a selection

Access projector menus

Turn volume up or down

Control playback of

connected device

Note:

• You must pair the projector remote control to the projector to use Android TV
and video-on-demand features. See the online User’s Guide for more
information.

Turn off audio and
video temporarily

Display the Android TV
home screen

Navigate menus

Operate Android TV features
using voice commands

Adjust image shape
(keystone)

Press the Enter button on the projector remote control to scroll through

3

the Welcome Guide. To use Android TV and video-on-demand features,
press and hold the home and Enter buttons to pair the remote control
to the projector.

The default language of the menu system is English. To select another

4

language, press the menu button on the projector remote control.
Select Settings and press Enter. Select Language and press Enter. Select
your language and press Enter. Press the menu button to exit.

Note: To shut down the projector, press the power button on the projector
or the projector remote control, then press the button again to confirm, if
necessary.

Adjust the image

Move the focus lever on top of the projector left or right to adjust the

1

image sharpness.

• The remote control for Android TV is only used to control the streaming
device if it is connected to a different device or projector. See the online
User’s Guide for more information.

Troubleshooting

If you see a No signal message after turning on the projector, check the

•

following:

Make sure the streaming device is properly connected to the HDMI

•

extension cable and the USB power cable.

For external video sources, make sure an HDMI cable is properly

•

connected to the projector’s HDMI extension cable.

If you see a blank screen, check the following:

•

Make sure the power light on the projector is blue and not

•

flashing.

Press the power button to wake the projector from standby or

•

sleep mode, if necessary.

If you see a blank screen when a computer is connected, check the

•

following:

To adjust the image height, press and hold the foot release lever on the

2

bottom of the projector to extend the front adjustable foot. Release the
lever to lock the foot in the desired position.

On some Windows® laptops, you may need to hold down the Fn key

•

and press F7 or the function key that lets you display on an external
monitor. It may be labeled CRT/LCD or have an icon such as .

On Windows 7 or later, hold down the Windows key and press P at
the same time, then click Duplicate.

If you’re using a Mac laptop, open System Preferences and

•

select Displays. Click the Arrangement tab and select the Mirror
Displays checkbox.

If the projector does not respond to remote control commands, make sure

•

the batteries in the remote control are installed correctly. Replace the
batteries if necessary.

The projector’s USB power cable can provide 2.0A of power. Make sure

•

your streaming device supports this specification.