Flight Force
™
3-IN-1 WATER DRONE
for ages
14
+
1
TABLE OF CONTENTS
Warnings and Cautions ....................................................1
Notice to Register Drones .................................................4
FCC Information ..........................................................5
Li-Po Battery Warning .....................................................6
AA Battery Precautions ....................................................6
Charging the Drone's Battery ..............................................7
Inserting the Controller Batteries ...........................................7
Drone Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controller Parts and Controls...............................................9
Sync the Drone with the Controller.........................................10
Flying Your Drone ........................................................11
Selecting Air or Land/Water Mode.........................................12
Trimming the Drone.......................................................13
Ending Flight.............................................................13
Gyro Calibration ..........................................................14
Headless Mode ..........................................................14
Key Return ..............................................................14
Stunt Play ...............................................................15
Troubleshooting ..........................................................15
Replacing Rotors .........................................................16
Care and Maintenance....................................................17
Specifications ............................................................17
Warranty.................................................................20
CAUTION
• TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
THERE ARE NO SERVICEABLE PARTS INSIDE.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
The lightning flash with arrow-head symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the unit’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the unit.
IMPORTANT SAFETY INSTRUCTIONS
All of the safety and operating instructions should be read, adhered to and followed
before the unit is operated.
SAVE THESE INSTRUCTIONS
2 3
DANGER
To reduce the risk of electric shock, burns, fire or injury:
1. Do not use while bathing or in a shower.
2. Do not place or store unit where it can fall or be pulled into a tub or sink.
3. Do not place in, drop or submerge in water or other liquid.
4. Do not reach for unit that has fallen into water. Unplug it immediately.
5. Care should be taken so that objects do not fall and liquids are not spilled onto the
unit.
WARNING
1. Close supervision is necessary when this appliance/product is used near children or
mentally disabled individuals.
2. This drone is recommended for use by persons aged 14 and older.
3. Use this unit only for its intended use as described in this manual.
4. Unplug this unit during lightning storms or when unused for long periods of time.
5. Never drop or insert an object into any opening.
6. Protect the charging cable from being walked on or pinched, particularly at plug
outlets, convenience receptacles and the point where it exits the unit.
7. Do not allow charging cable to touch hot surfaces. Wrap cord loosely around the
unit when storing.
8. The unit should be situated away from direct sunlight or heat sources such as radiators,
electric heaters, heat registers, stoves, or other units (including amplifiers) that produce
heat. Avoid placing on top of stereo equipment that radiates heat.
9. Never block the air openings of the unit with materials such as clothing, plastic
bags or papers, or place it on a soft surface such as a bed or couch, where the air
openings may be blocked.
10. Do not carry this unit by cord or use cord as handle.
11. Never operate this unit if it has a damaged cable, if it is not working properly, or if it
has been dropped or damaged, or dropped into water. If the unit’s charging cable or
plug is damaged, do not attempt to fix it yourself.
12. To avoid the risk of electric shock, do not disassemble or attempt to repair the unit.
Incorrect repair can cause risk of electric shock or injury to persons when unit is
used.
13. Do not operate in the presence of explosive and/or flammable fumes.
DRONE WARNINGS
1. The drone’s blades revolve at high speeds and can cause damage to the user,
spectators and animals. Stand away from the drone to reduce the risk of getting into
the flight path and always maintain visual contact with the drone while flying.
2. Warn spectators that you will be flying your drone so that they are aware of its
position.
3. Before flight, inspect the rotor blades to make certain that the blades are securely
fastened to the drone. Do not use if there is any damage that impacts flight
characteristics.
4. Before flying check your local laws and regulations pertaining to drone usage,
particularly around airports.
5. Operating the drone in a wide-open space is recommended. The ideal space should
have a 200-foot radius, without buildings, crowds, or electrical power lines.
6. Do not fly near tall buildings, high voltage cables, or other places that produce signal
interference. Signal interruptions may result in accidents.
7. Parental guidance or adult supervision is suggested at all times.
8. If you are flying the drone with others, make sure all spectators are behind you and at
least 6 feet from the drone.
4 5
9. For best performance, it is recommended that you operate the drone in light wind
conditions, as wind can greatly affect the performance of the aircraft.
CAUTION: DO NOT ATTEMPT TO FLY THE DRONE IF THERE IS RAIN, SNOW,
HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR
PRODUCT AND MAY CAUSE BODILY HARM.
WARNING!
• Choking/cutting hazard. Small parts/sharp rotor blades.
• Keep hands, hair and loose clothing away from the propeller when the power switch
is turned to the ON position.
• Not suitable for children under 14 years old. Parental supervision recommended.
NOTICE TO REGISTER DRONES
As of 12/21/15, the Federal Aviation Administration (FAA) requires all owners of drones
(Unmanned Aircraft Systems) that weigh more than 0.55 pounds to register their devices
at https://registermyuas.faa.gov/. Check your local civil aerial regulation as additional
state and/or local requirements may apply.
FCC INFORMATION
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This equipment may not cause harmful interference.
2. This equipment must accept any interference received, including interference that may
cause undesired operation.
WARNING: To comply with FCC's RF radiation exposure limits for general population/
uncontrolled exposure, the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
collocated or operating in conjunction with any other antenna or transmitter.
FCC ID: #085WL20160320
DO NOT FLY THE DRONE IN FOUL WEATHER!
WARNING
WARNING!
CHOKING HAZARD - Small
parts. Not suitable for children
under 3 years.
6
LI-PO BATTERY WARNING
This device contains a Lithium-Polymer battery. The battery must be recycled or disposed
of properly. Contact your local waste management office for information on battery
recycling or disposal.
Use only the supplied cable to recharge the battery. Improper charging may damage the
battery and the device.
Do not attempt to open the rechargeable battery or battery pack. There are no
serviceable parts inside.
Keep the battery out of reach of children. If swallowed, consult a physician immediately.
Do not expose the battery to high temperatures or dispose of battery in a fire as it may
explode. The battery may also explode if damaged.
BC
AA BATTERY PRECAUTIONS
Dispose of used batteries properly. Do not dispose of batteries in a fire.
Do not leave the batteries where a child or pet could play with or swallow them. If the
batteries are swallowed, contact a physician immediately.
The batteries may explode if mistreated. Do not attempt to recharge or disassemble the
batteries.
Use only fresh batteries of the required size and type. Do not mix old and new batteries,
different types of batteries, or rechargeable batteries of different capacities.
7
CHARGING THE DRONE'S BATTERY
The 3-in-1 Water Drone includes a rechargeable Lithium-Polymer battery. Charge the
battery before first use.
To charge the drone's battery:
1. Plug the provided charger into an electrical outlet.
2. Plug one end of the provided charging cable into
the charger.
3. Plug the other end of the charging cable into
the charging jack on the drone. The LED on the
charger will be red while charging.
4. When the battery is fully charged, the LED turns
off.
INSERTING THE CONTROLLER BATTERIES
The controller uses 6 AA batteries (included) which
must be inserted before first use.
To insert the controller's batteries:
1. Open the battery cover on the back of the
controller.
2. Insert 6 AA batteries, following the polarity
indicators.
3. Replace the battery cover.
8 9
DRONE PARTS AND CONTROLS CONTROLLER PARTS AND CONTROLS
Mode Buttons
Rotor (A)
Body Lights
Body
Rotor Cap
Rotor (B)
Motor
Rotor (A)
Waterproof Cover
Power Button
Switch Cover
Charger
Charging Cable
Charging Jack
Rotor (B)
Power LED
Speed Control Stick
Speed Trim
Direction Trim
Speed 40%
Speed 60%
Speed 80%
Mode Indicator
Speed Level
Diversion Trim Tips
Channel:Percentage
Real-time Display
Crab Trim Tips
Controller Battery Level
Mode Indicator
LCD Display
Headless Mode
Light Control/Key Return
Speed 100%
Crab Trim
Forward/Backward Trim
Direction Control Stick
Power Switch
Antenna
10
SYNCH THE DRONE WITH THE CONTROLLER
1. Ensure that the battery has been fully charged (see Page 7).
2. Place the drone on a flat surface.
3. Press the controller's Speed Control Stick (the left stick) all the way downward.
4. Slide the Controller's ON/OFF switch to the ON position and press the drone's
Power button to turn on the drone. The drone's lights will begin flashing.
5. When the drone's lights flash more slowly, move the Speed Control Stick to its upper
limit.
6. Move the Speed Control Stick down again, to its starting position; you will hear a
beep. The controller and drone are now synched.
11
FLYING YOUR DRONE
It is very important to spend time learning to control your drone in a safe environment
before flying it in more challenging conditions. Practice the following moves until you are
fully confident in your abilities.
1. Charge and insert batteries and sync the drone and Controller, as described
previously.
2. Power on the Controller and the drone.
3. Place the drone on a flat surface in a wide open area, with the tail of the drone
toward you. Stand at least 6 feet (2 meters) diagonally behind the drone. Ensure
that there are no people or objects in the immediate area.
Note: By default, the drone is in Air mode. If you want to practice in Water/Land
mode, see Page 12.
4. Press the Speed 40% button. While learning to fly your drone, it is advisable to use
the lowest speed setting.
5. Start with the Speed Control Stick in the bottom position. Gently
press the Speed Control Stick up to increase the height, and right
and left to turn. Be sure you can make the drone hover, staying
in a fixed position in mid air. Experiment with the Speed Control
Stick until you can comfortably control the speed and turns.
If the drone flies too far away from you, land the drone and move closer to it, then
continue practicing.
6. Practice changing the direction of movement with the Direction
Control Stick. Move the stick forward and backward to move
forward and backward when flying. Move the stick left and right to
change direction left and right.
7. When you can comfortably control your drone, you can experiment
with faster speeds by pressing the Speed 60%, 80% and 100% buttons.
SELECTING AIR OR LAND/WATER MODE
You can operate the drone in the air, on land, or in the water. Press either Mode Button to
select your mode. In land and water mode, the rear propellers tilt forward.
In air mode:
• Press the Speed Control Stick (the left stick) up and down to control the height of
your flight; press left and right to turn left and right.
• Press the Direction Control Stick (the right stick) up to fly forward, down to fly
backward, left and right to fly left or right.
In land/water mode:
• Press the Speed Control Stick (the left stick) up and down to control the speed of
your drone; press left and right to turn left and right.
• Press the Direction Control Stick (the right stick) to move forward; press left and
right to move left and right. You cannot move backward in land/water mode.
When using the drone in water, note the following.
• Before placing or landing in water, check that the waterproof switch cover is in place.
After removing from water, open the switch cover and check that the switch is dry. If
necessary, gently dry the switch.
• If the drone's head tilts forward, the blades will beat the water and forward
resistance increases. Correct the tilt.
• If the drone capsizes, push the left control stick to flip the drone over.
• Do not operate at high speed in water, which may cause the drone's head to tilt up,
risking a backflip. If the drone flips, it may fly out of the water.
• Press the right joystick backward to slow down.
TRIMMING THE DRONE
To ensure that your drone can fly straight and level, you must calibrate its movements so
it remains stable both in takeoff and in flight. This is referred to as trimming.
Slowly raise the Speed Control Stick. Just as the drone lifts off the ground, use the trim
buttons to make adjustments.
• If the nose leans right, press the Direction Trim to the left. If the
nose leans left, press the Direction Trim to the right.
• If the nose leans forward, press the Forward/Backward Trim
down. If the nose leans backward, press the Forward/Backward
Trim up.
• If the body leans right, press the Crab Trim to the left. If the body
leans left, press the Crab Trim to the right.
ENDING FLIGHT
To end your flight, bring the drone back to a safe position, then switch off the Controller
and drone. If you will not be flying again for several days, remove the batteries from the
Controller and store them in a cool, dry place until your next flight.
12 13
GYRO CALIBRATION
If the drone is experiencing difficulty flying or is behaving erratically, the gyroscopes may
need to be recalibrated. Do not attempt to do this while flying. Safely land the drone
before attempting this procedure.
Place the drone in a horizontal location. Pull both control sticks to the bottom left (45°) at
the same time for 2 seconds, then release both sticks. The drone will flash to start gyro
calibration. When the drone flashes for 2 seconds and then stops flashing, the calibration
is complete and the craft is ready to fly.
HEADLESS MODE
You can set the forward direction of your drone relative to your controller's position. The
end of the drone facing away from you will be "forward", regardless of the position of the
front and back of the drone.
To enter Headless Mode, place the drone in front of the Controller.
After take off, long-press the Headless Mode button for 2 seconds.
The drone will beep, indicating that it is now in headless mode.
To exit Headless Mode, press the Headless Mode button for 2 seconds.
NOTE: When using Headless Mode, the drone must be in front of the
Controller.
KEY RETURN
To bring the drone directly back to the Controller, press the Light
Control/Key Return button for 2 seconds. A beep will sound, the
drone's lights will flash, and the drone will return to the Controller.
To cancel the return, press the Light Control/Key Return button for 2
seconds.
NOTE: The Controller will not control the drone during the return.
14
STUNT PLAY
When the drone is in land and sea mode and you are operating at high speed (with the
Speed 80% or 100% button activated), if you press the Speed Control Stick (the left
stick) up the drone will fly up in a dramatic display.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
When starting the drone, the
indicator lights flash but there
is no response to Controller
controls.
Unable to sync to the
Controller.
See Page 10 for sync
instructions.
Pressing the drone's start
button does not start the drone.
The battery may be depleted. Recharge the battery.
The motor does not respond to
the speed stick, the Controller
LED flashes.
The battery may be depleted. Recharge the battery.
The main rotor continues to
spin after landing.
The Speed Trim accidentally
increased during flight.
Confirm that the Speed Trim is
in or slightly below the center.
The main rotor spins but the
drone is unable to take off.
The main blades have been
damaged or the battery is
depleted.
Replace the blades or charge
the battery.
The drone has a strong
vibration.
The main blades have been
damaged.
Replace the blades.
The tail is not trimmed after
adjustment, or there is
inconsistent speed during left/
right spin.
The tail drive motor or tail
rotors have been damaged.
Replace the motor or replace
the main wing.
15
PROBLEM POSSIBLE CAUSE SOLUTION
Drone moves forward
during hover, even after trim
adjustment.
The drone was not level during
power up, or the elevator stick
was pushed for too long or too
short a time.
Shut down and restart the
drone.
Cannot fly the drone after a
crash.
The motor has been damaged
or a gear loosened.
Check the motor and gears
and tighten if necessary.
The drone is not controlled,
or is unable to power off, or
cannot fly using the normal
power supply.
Crashes may have damaged
the unit, or it has had a shortcircuit due to exposure to
water.
Open the charging port, pull
out the shorting cap, cut off
the power, and re-install.
Be sure the drone electronics
are dry.
When switching between air
and land/water mode, the
drone makes an unusual sound.
The rotor blade may be loose. Check the rotor blades and
ensure they are properly
installed.
REPLACING ROTORS
If a rotor becomes damaged, you can replace it.
To replace a rotor:
1. Remove the rotor's cap by turning it in the opposite direction of the arrow on the
rotor to be replaced.
2. Pull out the broken rotor and insert a new rotor marked with the SAME direction
arrow (clockwise/counterclockwise).
3. Screw the rotor cap back on by turning it in the direction of the arrow on the rotor.
16 17
CARE AND MAINTENANCE
• Clean with a soft, damp cloth.
• Do not use harsh cleaning agents.
• Check components regularly, such as the rotor blades, chassis, motors. If any
component is damaged or worn, do not use the drone until the component has been
repaired or replaced.
• Remove the Controller's batteries before storing.
• Store in a cool, dry location. Do not store in high temperatures or near a heat
source.
SPECIFICATIONS
Drone Size ........................................................................... Approx. 14.4 x 14.4 x 4.7 in (37 x 37 x 12 cm)
Drone Weight ...............................................................................................................................Approx. 1.2 lbs (544 g)
Controller Batteries .................................................................................................................................1.5V AA type (6)
Controller Operation Time .................................................................................................................Approx. 18 hours
Drone Battery .........................................................................................................7.4V 1200mAH Lithium-Polymer
Drone Operation Time ...............................................................................................................Approx. 6 - 7 minutes
Drone Battery Charge Time ...................................................................................................Approx. 120 minutes
Charger Input ...........................................................................................................................................................................220V
Charger Current ................................................................................................................................................................800mA
Charger Full Voltage ......................................................................................................................................8.4 +/- 0.03V
18 19
NOTESNOTES
ONE (1) YEAR LIMITED WARRANTY
Brookstone® warrants this product against defects in materials and/or workmanship
under normal use for a period of ONE (1) YEAR from the date of purchase by the
original purchaser (“Warranty Period”). If a defect arises and a valid claim is received
within the Warranty Period, at its option, Brookstone will either 1) repair the defect
at no charge, using new or refurbished replacement parts, or 2) replace the product
with a new product that is at least functionally equivalent to the original product, or
3) provide a store credit in the amount of the purchase price of the original product.
A replacement product or part, including a user-installable part installed in accordance
with instructions provided by Brookstone, assumes the remaining warranty of the
original product. When a product or part is exchanged, any replacement item becomes
your property and the replaced item becomes Brookstone’s property. When a store
credit is given, the original product must be returned to Brookstone and becomes
Brookstone’s property.
Obtaining Service: To obtain warranty service, call Brookstone Limited Warranty Service
at 1-800-292-9819. Please be prepared to describe the product that needs service
and the nature of the problem. A purchase receipt is required. All repairs and
replacements must be authorized in advance. Service options, parts availability and
response times will vary. You are responsible for delivery and the cost of delivery of
the product or any parts to the authorized service center for replacement, per our
instructions.
Limits and Exclusions: Coverage under this Limited Warranty is limited to the United
States of America, including the District of Columbia and the U.S. Territories of
Guam, Puerto Rico, and the U.S. Virgin Islands. This Limited Warranty applies only
to products manufactured for Brookstone that can be identified by the “Brookstone”
trademark, trade name, or logo affixed to them or their packaging. The Limited
Warranty does not apply to any non-Brookstone products. Manufacturers or
20
suppliers other than Brookstone may provide their own warranties to the purchaser,
but Brookstone, in so far as permitted by law, provides these products “as is.”
This warranty does not apply to: a) damage caused by failure to follow instructions
relating to product’s use or the installation of components; b) damage caused by
accident, abuse, misuse, fire, floods, earthquake or other external causes; c) damage
caused by service performed by anyone who is not a representative of Brookstone;
d) accessories used in conjunction with a covered product; e) a product or part
that has been modified to alter functionality or capability; f) items intended to be
periodically replaced by the purchaser during the normal life of the product including,
without limitation, batteries or light bulbs; g) any product sold “as is” including, without
limitation, floor demonstration models and refurbished items; or h) a product that is
used commercially or for a commercial purpose.
BROO KSTONE SHALL NOT BE LIAB LE FOR INCI DENTAL OR CONSEQU ENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING
OUT OF ANY BR EACH OF THIS WARRANTY. TO THE EXTENT PE RMITTED BY
APPLICABLE LAW, BROOKSTONE DISCLAIMS ANY AND ALL STATUTORY OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF BROOKSTONE
CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTI ES, THEN
TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE
LIMITE D IN DURATION TO THE DU RATION OF THIS EXPRESS WARRANTY.
Some states disallow the exclusion or limitation of incidental or consequential damages
or how long an implied warranty lasts, so the above exclusions or limitations may not
apply to you. This warranty gives you specific legal rights and you may also have other
rights, which vary from state to state.
21
324457
Rev 2
© Brookstone 2017
Find thousands more
great ideas online
Brookstone.com | 1-800-846-3000
1 Innovation Way, Merrimack, NH 03054
Loading...