Brondell S1400-EW, S1400-EB, S1400-RW, S1200-RW, S1400-RB User Manual

Name: Brondell S1400-EW
Brand: Brondell
SKU: 2539650
Rating: 4 (2 reviews)

...

4 (2)

OWNER’S MANUAL

Swash 1200/1400 Luxury Bidet Toilet Seats

S1200-EW S1400-EW S1400-EB

S1200-RW S1400-RW S1400-RB

Attach Proof of Purchase to This Page

Joindre une preuve d’achat à cette page Adjunte prueba de compra a esta página

CONTENTS

This manual contains important safety information. Before operating the bidet, please read this manual thoroughly, and retain it for future reference.

GENERAL INFO

02 SAFETY INFORMATION

06 PRODUCT INFORMATION

06 Product Features

08 Product Dimensions

09 Product Parts

PRODUCT INSTALLATION

10 PRODUCT INSTALLATION

10Installation Parts

11Before Installation

11Swash Installation

14Remote Control Installation

15External Bidet Filter Installation

PRODUCT OPERATION

16 OPERATING THE SWASH

16 S1200 Remote Control Guide

18 S1400 Remote Control Guide

20Bidet Seat Controls Guide

21Using the Swash 1200/1400

25Using the Swash 1400’s

Additional Features

26 Swash Special Mode Operations

TECHNICAL INFO

28PRODUCT SPECIFICATIONS

29MAINTENANCE

29Seat Cleaning & Removal

29Nozzle Cleaning

30Replacing the Deodorizer Cartridge

30Cleaning the Mesh Filter

31Product Storage & Use

31 TROUBLESHOOTING

34 WARRANTY

TRANSLATIONS

36 SPANISH

72 FRENCH

SAFETY INFORMATION (IMPORTANT SAFEGUARDS)

Be careful to keep this safety information. Please read this information to prevent property loss and ensure safety.

DANGER:

If not observed, serious injury or even death may occur as a result.

WARNING:

If not observed, serious physical injury or property damage may occur as a result.

CAUTION:

If not observed, minor physical injury or property damage may occur as a result.

READ ALL INSTRUCTIONS BEFORE USING

DANGER

Failure to observe the following warnings may result in electric shock, fire, personal injury, property damage or product damage:

• The remote control for this product contains a button style coin battery. If swallowed, it can cause severe injury or death in just 2 hours. Keep the remote away from children and seek medical attention immediately if suspected ingestion of the battery occurs.

• Do not use a damaged power plug or plug into a loose electric outlet. • Do not move the product by pulling the power cord.

• Do not handle the product or power plug with wet hands.

• Do not forcefully bend the power cord or place heavy objects on it to prevent it from being damaged or deformed.

• Do not connect and pull out the power plug or cord repeatedly.

• Unplug the product before cleaning, repairing, inspecting, or replacing parts. • Remove any dust or water from the power plug prior to plugging in.

• Do not plug the product into an electrical outlet or power strip that is being used by too many other products. Use an electrical outlet adequate for the wattage of the product rated for a minimum of 15 amps.

• If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself. Contact the Brondell Service Center toll free at 888-542-3355 or email us through our website.

• If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately from the electrical outlet and contact Brondell. Failure to do so may result in electric shock or fire.

• Do not insert any wires or sharp objects into any product gaps. This may result in electric shock, fire, or product damage.

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION (cont.)

(IMPORTANT SAFEGUARDS)

DANGER

• Do not place an electronic or gas heater near the product or dispose of any burning materials such as a lit cigarette in the toilet. This may result in fire or product deformation. Do not place any containers filled with water or other liquids, food, metallic objects, or any flammable material on top of the product. If foreign material enters the product, this may result in electric shock or fire.

• Do not use the product in locations exposed to excessive moisture and do not splash water onto the product.

• While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise caution to ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so may result in electric shock or fire.

• If foreign material enters the product, pull the power plug out of the electrical outlet, turn off the main water valve, and call the Brondell Service Center.

• Do not disassemble, repair, or modify the product yourself. • Do not use the product while wet from bathing or showering.

• Do not place or store the product where it can fall or be pulled into a tub or sink. • Do not place in or drop the product into water or any other liquid.

• Do not reach for the product if it has fallen into water. Unplug the product immediately and call the Brondell Service Center.

• Do not use the product if it is not working properly. Please unplug the product immediately, close the main water supply valve, and call the Brondell Service Center at 888-542-3355. Failure to do so may result in electric shock, fire, or flooding.

WARNING

Failure to observe the following warnings may result in electric shock, fire, personal injury, property damage or product damage.

• Do not plug in, operate, or store the unit in locations where flammable or combustible materials are used or kept.

• Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease. • Turn off the main water supply valve when cleaning.

• For children and seniors who may have difficulties with adjusting temperatures or those with sensitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low” or “off” to prevent burning.

• Close supervision is necessary when this product is used by children, seniors, or persons requiring general assistance.

• Do not press the buttons using excessive force.

• Do not stand on top of or place any heavy objects onto the seat cover.

• Use this product for its intended use only, as described in this manual. Do not use any attachments that are not recommended by Brondell.

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION (cont.)

(IMPORTANT SAFEGUARDS)

WARNING

• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact the Brondell Service Center for examination and repair.

• Keep the cord away from heated surfaces and heating vents.

• Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, etc.

• Never drop or insert any object into any opening or hose.

• Do not use the product outdoors or operate where aerosol (spray) products are being used or a room where it could be exposed to oxygen.

• Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in the next pages of the manual.

CAUTION

Failure to observe the following warnings may result in electric shock, fire, personal injury, property damage, or product damage.

• For California Residents: CR2032 batteries contain Perchlorate Material - special handling may apply. Visit http://www.dtsc.ca.gov/hazardouswaste/perchlorate for more information.

• Do not connect the main water supply to the hot water pipe or supply (only connect to the cold water supply).

• After the installation, make sure to check all water supply connections for leaks. Rubber washers should be in place for the water connection hoses & T-Valve.

• Do not open/close the seat or seat cover with excessive force.

• Exercise caution that urine does not come into contact with the product - failure to do so may result in bad odors or malfunction.

• If the product will not be used for a long period of time, unplug the power cord, close the main water supply valve, and drain any water in the water tank.

• Do not pull out the bidet hose using excessive force.

• Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or near the product. This may result in corrosion to the metal parts or discoloration or scratches to the bidet body.

• This appliance is not intended for use by persons (including children and seniors) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION (cont.)

(IMPORTANT SAFEGUARDS)

GROUNDING AND GFI OUTLET INSTRUCTIONS

This product should only be used with a grounded GFCI (Ground Fault Circuit Interrupter) outlet and a grounded three-prong electrical cord as shown to the right. In the event of an electrical short circuit, using a grounded GFCI outlet reduces the risk of electric shock.

This product is equipped with a grounded cord and is for use on a nominal 120V circuit only (minimum 15 amps) and must be plugged into an outlet that is properly grounded with a GFCI breaker as shown. Replace or repair a damaged cord immediately.

Ground GFCI Outlet

Test

Reset

Grounding Pin

Improper use of the grounding plug can result in a risk of electric shock.

• If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with green insulation (either with or without a yellow stripe) is the grounding wire.

• Check with a qualified electrician if the grounding instructions are not completely understood, or if there is doubt if the product is properly grounded.

Extension Cord Use

If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps with a three-wire extension cord with a three-blade grounding plug. Only plug into a three-slot grounded GFCI receptacle that will accept the plug of the product. Replace or repair any damaged cords immediately.

SAVE THESE INSTRUCTIONS

PRODUCT INFORMATION

S1200/1400 PRODUCT FEATURES

Dual Stainless Steel Nozzles – separate stainless steel nozzles resist soiling and bacterial contamination for enhanced hygiene. The dual nozzle configuration ensures accurate coverage for all types of users.

Aerated Wash Spray – micro-bubbles introduced into the wash spray create a gentler, softer wash action designed for sensitive skin. In addition, the aerated spray reduces overall water consumption and is more effective in washing the skin.

Positionable Nozzles – each nozzle has seven different positions to ensure the most comfortable and complete wash.

Ergonomic Heated Seat – with four temperature settings (High/Med/Low/Off).

Night Light – an illuminating night light means no more blinding lights during midnight trips to the bathroom.

Sturdy, “Sittable” Lid – the strong bidet seat lid will support up to 270 pounds.

Gentle Closing Seat and Lid – “slam free” gentle closing seat and lid are user friendly.

Instant and Endless Warm Water – the cutting-edge instant ceramic heating system ensures an endless warm water stream for posterior and feminine washes.

Adjustable Water Temperature and Pressure – each wash mode (Front and Rear) has four available water temperature settings, and three water pressure settings.

Wide Spray Option – three width settings widens the wash spray from a strong concentrated stream to a soft spray for a more personal and thorough wash.

Wireless Remote Control – the intuitive remote control comes with a convenient magnetic dock and mounting bracket, and includes its own Eco Mode to conserve battery life.

Two User Memory Settings – personalize your settings like water temperature, water pressure, and even the spray width to your own preferences and retain them with two programmable profile settings.

“Auto” Function – activates a preset for either a Front or Rear wash cycle. The Dry cycle will then activate with the Swash 1400. See page 22 for more details.

Automatic Eco Mode – this function automatically lowers the seat temperature ten minutes after the Swash was last used.

Quick-Release Seat – quick-release button for easy removal and cleaning of seat and toilet.

S1400-ONLY PRODUCT FEATURES

Warm Air Dryer – includes adjustable temperature with three levels for a hands-free experience and toilet paper reduction – even elimination.

Nozzle Oscillation – the move function provides a massaging, oscillating cleanse during the wash cycle ensuring a thorough and comfortable wash.

Nozzle Sterilization – utilizing silver as a natural antibacterial agent we are able to create a sterilizing wash for the nozzles that is 100% chemical and maintenance free keeping them clean, hygienic, and corrosion free.

Deodorizer – the activated charcoal deodorizing filter eliminates odors at the source. It does not cover or mask odors, but eliminates them by removing air from the toilet bowl, passing it through the replaceable filter and expelling the clean air through the vent in the back of the Swash.

PRODUCT INFORMATION (cont.)

PRODUCT DIMENSIONS

Elongated Top View

8 in

14.25 in

15.2 in

5.3 in

15.125 in

Round Top View

8 in

14.25 in

15.2 in

5.3 in 14.25 in

Bottom View	Distance Between
	Mounting Holes
5.25 – 8.3 in	5.25 – 8.3 in

2.9 in

Rear Fixing Distance: 6.9 in

PRODUCT PARTS

1.	Lid
2.	IR Sensor
3.	Stainless Steel Nozzles	1
3.	Stainless Steel Nozzles	1

4.	Body (seat) Sensor
5.	Seat
6.	Power Cord
7.	Bidet Hose		2
8.	T-Valve		2
8.	T-Valve
9.	Drain Plug		3
10.	Water Inlet		4
11.	Quick Release Button		4
11.	Quick Release Button
12.	Mounting Plate		5
13.	Deodorizer	6	5
13.	Deodorizer	6
14.	Night Light
15.	Remote Control
		7	8
			15
		11
	9
	10

PRODUCT INSTALLATION

INSTALLATION PARTS

1.	Mounting Bolt (2)	8.	Bidet Hose
2.	Rubber Cone Washer (2)	9.	Cable Clips (2)
3.	Flat Washer (2)	10.	Remote Control Wall Mount
4.	Barrel Nut (2)	11.	Remote Screw (2)
5.	Mounting Plate	12.	Remote Anchor (2)
6.	Adjustable Bracket (2)	13.	CR2032 Batteries (4)

7.T-Valve Connector with Rubber Washer

1	5
2
3	6
4

11 12

BEFORE INSTALLATION

WATCH OUR INSTALLATION VIDEO

Installation for all Swash products can be found online at brondell.com

CHECK FOR TOP MOUNT INSTALLATION

If your fixture only has top-side access to the mounting bolts that hold the seat to the toilet, you will likely need to purchase the Swash Bidet Seat Top Mount Hardware Kit, found on brondell.com.

CHECK FOR A CONCEALED TOILET FILL VALVE

Many modern toilets have sleek designs intended to cover and camouflage plumbing connections, which makes a standard Swash installation difficult or impossible. For this, we recommend using our Alternate Swash Bidet Seat T-Valve, found on brondell.com.

CHECK WATER SUPPLY LINE

Check the line that connects the toilet tank to the water shut off valve. If it is a rigid pipe, you may need to purchase a flexible hose to replace it before installing the Swash. The length of the hose and the size of the connectors will vary.

RESIDUAL MOISTURE IS NORMAL

Every product is tested with pure water during production to ensure the highest quality and performance. It is normal to find a small amount of residual moisture on the product and in the reservoir and filter.

TOOLS

A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a standard wrench may be needed for tight water supply connections. Teflon tape can be helpful in creating a water-tight seat between plumbing connections.

SWASH INSTALLATION

Please read these instructions carefully before installing the Swash. Failure to do so could result in flooding, leaking or damage to the product.

1.Existing Toilet Seat Removal

a.Lift hinge covers and use a screwdriver to remove the mounting bolts.

b.Remove the toilet seat.

NOTE: Steps may vary by type of seat and toilet

PRODUCT INSTALLATION (cont.)

SWASH INSTALLATION (cont.)

2.Turn Off Water Supply Valve and Flush Toilet

a.Turn water valve off to stop the flow of water.

b.Flush toilet and hold down handle to completely empty tank.

c.Disconnect water supply hose from toilet tank. Do not disconnect from the water supply valve.

NOTES:

•You may wish to place a container under the tank to catch any excess water.

•Do not continue without completing the above steps

•Failure to do so could result in flooding, leaking or damage to the Swash.

3.Connect T-Valve to the Toilet Tank Fill Valve

a. Place the flat edge of the rubber washer into the T-Valve against the metal with the raised lip facing the toilet tank connection.

b. Install the T-Valve with the rubber washer to the incoming water connection on the bottom of your toilet tank.

NOTES:

•The T-Valve connects to the fill valve directly under your toilet tank - it does not connect at the wall.

•Only connect to the cold toilet water supply line.

•If your water supply line is rigid you may need to replace it before continuing.

4.Connect the water supply line coming from the wall to the bottom of the T-Valve.

5.Install Mounting Plate

a. Place adjustable mounting plate over mounting holes on toilet, rubber side faces down, curved edge faces toward the toilet tank.

b. Place adjustable brackets flat side down in the center of the square opening in the mounting plate and insert mounting bolts through adjustable brackets and mounting holes. Be sure that the square mounting bolt head is even with sides of adjustable bracket.

c. Slide rubber cone washer, flat washer, and then barrel nut onto mounting bolts under the toilet bowl and tighten to keep mounting plate in place.

Step 2c

raised lip (faces up)

Step 3a

toilet tank

t-valve

cold water supply line

Steps 3-4

Steps 5b & 5c

SWASH INSTALLATION (cont.)

6.Connect the Bidet Hose to the Seat

a.Connect the bidet hose to the water inlet. Hand-tighten to secure. Take care not to twist the bidet hose, excessively bend it, or strip the plastic screw threads when screwing the hose onto the bidet seat.

7.Attach the Swash to the Mounting Plate

a.Set the Swash flat on the toilet bowl in front of the mounting plate, and slide seat onto plate until it is secure and “clicks” into place.

b.If the seat appears too short or too long for the toilet, adjust the mounting plate accordingly. To adjust the mounting plate, loosen barrel nuts underneath the toilet and slide seat forward or backwards as needed. Once the seat is lined up properly, tighten barrel nuts to hold in place.

8.Connect the open end of the Bidet Hose to the T-Valve.

9.Turn On Water Supply

a.Open the main water supply valve slowly and check for leaks.

b.Wait 5 minutes, check again and if there are no leaks continue.

10.Connect Power

a.Plug the power cord into the electrical outlet.

b.If desired, use the included Cable Clips to connect the power cord and bidet hose side-by-side for a tidier appearance.

NOTES:

•Make sure to only use a grounded GFCI (ground fault circuit interrupter) electrical outlet. In the case of a short circuit, a grounded GFCI outlet may help prevent electric shock or injury.

•If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps with a threewire extension cord with a three-blade grounding plug.

Step 6a

Step 7b

Step 8

Step 10b

PRODUCT INSTALLATION (cont.)

REMOTE CONTROL INSTALLATION

1. Battery Installation

a. Separate the remote control from the magnetic dock.

b.Turn remote over and open the child-proof battery compartment by popping off the battery cover with a flat-head screwdriver or small coin. Insert the four

included CR2032 batteries “plus” side up and replace

battery cover.

c. To confirm the batteries are installed correctly, press the Stop button and you should see the “Wide Spray” LED Step 1b

light turn on for a few seconds (NOTE: the 2 other LED lights may or may not turn on at this time depending on the current settings).

2. Mount Remote (optional)

a. Identify a location in the bathroom for the remote

control that is visible and reachable from the toilet.

b. Depending on the wall type, you can install using the supplied screws and anchor mounts or use the provided double stick tape on the back of the remote wall mount.

Make sure the remote mount is fully secure with either

method so that it does not fall and damage the remote Step 2c control.

c. Place the remote control into the mount as shown.

DANGER – Important Battery Information:

1.Remote contains “coin-style” batteries – keep away from children. If swallowed, seek medical attention immediately.

2.Ingestion of batteries may cause severe injury or death in just 2 hours.

3.Use only CR2032 batteries. Do not mix new and old batteries together.

4.Double-check the + and – direction.

5.Take care when opening the battery compartment to replace the batteries - the batteries are spring-loaded.

6.Dispose of old batteries carefully.

For California Residents: CR2032 batteries contain Perchlorate Material - special handling may apply. Visit http://www.dtsc.ca.gov/hazardouswaste/perchlorate for more information.

EXTERNAL BIDET FILTER INSTALLATION

NOTE:

•Customers with hard water, well water, and softened water can extend the life of their bidet seat by purchasing and installing an external inline water filter to be used with the Swash. The bidet filter should be changed every six months.

1.Turn Off Water Supply Valve and Flush Toilet.

a.Turn water valve off to stop the flow of water.

b.Flush toilet and hold down handle to completely empty tank.

2.Disconnect the Bidet Hose from the T-Valve

3.Connect the female end of the Swash Filter to the Open T-Valve Connection.

4.Connect the Bidet Hose to the male end of the Swash Filter.

Step 2

FLOW

5. Turn the toilet water supply valve back on.

Step 3

FLOW

Step 4

OPERATING THE SWASH

QUICK REFERENCE GUIDE – S1200 REMOTE CONTROL

Rear Wash 2

Water Pressure 5

Seat Temp. & Indicator 7

Spray Width & Indicator 8



10		12
User 1		User 2
Memory		Memory
	11

Auto

Mode

1Remote Control IR

Signal Transmitter

3 Front (Feminine) Wash

4 Stop

6 Nozzle Position

9 Water Temp. & Indicator

QUICK REFERENCE GUIDE – S1200 REMOTE CONTROL (cont.)

SEE DIAGRAM ON PAGE 16

1. Remote IR Signal Transmitter

Transmits the signal from remote control to the seat when a button is pressed.

2.Rear Wash Button

This button activates the aerated Rear Wash function.

3.Front (Feminine) Wash Button

This button activates the aerated Front, or “Feminine”, Wash function.

4.Stop Button

Stops all functions currently operating.

5.Water Pressure Buttons

These buttons increase or decrease the water pressure, to one of three settings, during either of the aerated wash cycles.

6.Nozzle Position Buttons

These buttons move the wash nozzle, to one of seven positions, during either of the aerated wash cycles.

7.Seat Temp. & Indicator

Indicates the Seat Temperature setting. Press the button to cycle through each setting.

Off, Low - 89° F (blue), Medium - 93° F (pink), High - 97° F (red)

8.Spray Width & Indicator

Indicates the wash Spray Width setting. Press the button to cycle through each setting.

Concentrated (blue), Medium (pink), and Wide (red)

9.Water Temp. & Indicator

Indicates the Water Temperature setting. Press the button to cycle through each setting.

Off - incoming water temp., Low - 90° F (blue), Medium - 95° F (pink), High - 100° F (red)

10.User Memory 1

This button contains the programming for all of the customizations set in User 1’s wash cycles. See page 23 for more details.

11.Auto Mode

This button automatically runs a pre-programmed wash (front or rear) cycle. See page 22 for more details.

12.User Memory 2

This button contains the programming for all of the customizations set in User 2’s wash cycles. See page 23 for more details.

Brondell S1400-EW, S1400-EB, S1400-RW, S1200-RW, S1400-RB User Manual

OPERATING THE SWASH (cont.)

QUICK REFERENCE GUIDE – S1400 REMOTE CONTROL

Rear Wash

Nozzle Oscillation

Dry Temperature / Water Pressure (increase & decrease)

Seat Temp. & Indicator

Spray Width & Indicator

Nozzle Sterilization

2
5
7
9
10
12
14
User 1
Memory
15
Auto
Mode

1
3
4
6
8
11
13
16
User 2
Memory

Remote Control IR

Signal Transmitter

Front (Feminine) Wash

Stop

Warm Air Dryer

Nozzle Position (forwards & backwards)

Water Temp. & Indicator

Deodorizer

QUICK REFERENCE GUIDE – S1400 REMOTE CONTROL (cont.)

SEE DIAGRAM ON PAGE 18

1. Remote IR Signal Transmitter

Transmits the signal from remote control to the seat when a button is pressed.

2.Rear Wash Button

This button activates the aerated Rear Wash function.

3.Front (Feminine) Wash Button

This button activates the aerated Front, or “Feminine”, Wash function.

4.Stop Button

Stops all functions currently operating.

5.Nozzle Oscillation (Move) Button

This button activates the Nozzle Oscillation function. When activated, the front or rear nozzle moves back and forth during the wash cycle to clean a wider area. Push the button again to stop the oscillation.

6.Dry Button

Turns on the Warm Air Dryer for a period of two minutes.

7.Water Pressure/Dry Temperature Buttons

These buttons increase or decrease the water pressure, to one of three settings, during either of the aerated wash cycles. During the Dry cycle, these buttons increase or decrease the temperature of the Warm Air Dryer.

8.Nozzle Position Buttons

These buttons move the wash nozzle, to one of seven positions, during either of the wash cycles.

9.Water Temp. & Indicator

Indicates the Water Temperature setting. Press the button to cycle through each setting.

Off - incoming water temp., Low - 90° F (blue), Medium - 95° F (pink), High - 100° F (red)

10.Spray Width & Indicator

Indicates the wash Spray Width setting. Press the button to cycle through each setting.

Concentrated (blue), Medium (pink), and Wide (red)

11.Seat Temp. & Indicator

Indicates the Seat Temperature setting. Press the button to cycle through each setting.

Off, Low - 89° F (blue), Medium - 93° F (pink), High - 97° F (red)

12.Nozzle Sterilizer

Utilizing silver as a natural antibacterial agent, this sterilizing wash is 100% chemical and maintenance-free, keeping the nozzles clean, hygienic, and corrosion-free.

13.Deodorizer

Eliminates odors by removing air from the toilet bowl, passing it through the replaceable active carbon filter, and expelling the clean air through the vent in the back of the Swash.

14.User Memory 1

This button contains the programming for all of the customizations set in User 1’s wash and dry cycles. See page 23 for more details.

15.Auto Memory

This button automatically runs a pre-programmed wash (front or rear) and dry cycle. See page 22 for more details.

16.User Memory 2

This button contains the programming for all of the customizations set in User 2’s wash and dry cycles. See page 23 for more details.

OPERATING THE SWASH (cont.)

BIDET SEAT CONTROLS GUIDE

Basic functions such as Rear Cleansing and Nozzle Cleaning can be used without the remote by utilizing the auxiliary buttons shown below.

	1
2
3
	7
4
	6
	5
1	1
	1

SEAT DISPLAY

1. Remote IR Receiver (3)

Receives signal from remote control.

2.Power Indicator

This indicator is illuminated when the bidet is powered on. This indicator is turned off when Eco Mode is activated.

3.Eco Mode Indicator

This indicator is illuminated when Eco Mode is enabled and activated, ten minutes after the Swash was last used or programmed.

4.Seat Temperature Indicator

This indicator is illuminated when the seat temperature is set to Low, Medium, or High. The indicator is turned off when the seat temperature is off. This indicator is also turned off when Eco Mode is activated.

AUXILIARY CONTROL PANEL

5.Power Button

Turns the seat On/Off. Press and hold the button for 2 seconds to turn off.

If the Power button is pressed while any wash function is operating, the wash function will stop.

6.Rear Cleansing Button

Initiates the rear wash function utilizing the settings last used.

7.Nozzle Cleaning Button

When pressed, one nozzle will fully extend, allowing for easy cleaning. Press again for the second nozzle to extend and once more to retract both nozzles.

USING THE SWASH 1200/1400

NOTES:

•The wash functions will not work unless the sensor in the seat detects someone sitting down (skin conductivity sensor). To override the Seat Sensor, please refer to the section on page 27.

•The remote control will not operate the Swash if the batteries are weak, dead, or not installed properly (remote requires 4 x CR2032 batteries to function).

Warm Water Aerated Wash

1.Sit on the seat to ensure skin-to-seat contact. The seat will give an audible response letting you know the seat sensor has been engaged. At the same time an automatic self-cleaning cycle will occur - a small amount of water will flush over the nozzles and into the toilet bowl.

2.Press the Front or Rear button on the remote to begin water flow. The nozzles will self-clean and purge a small amount of water which will last for several seconds prior to starting the wash function – please note that this may take up to 20 seconds.

The front or rear wand will extend and wash for 2 minutes, then turn off automatically.

3.To keep the wash continuing longer than 2 minutes, press the Front or Rear button again during the wash cycle. Each time you press the button during the wash cycle, the 2 minute cycle starts again.

4.If you would like to stop the wash before the 2 minute cycle ends, press the Stop button to discontinue flow.

5.While washing, users can adjust the water temperature, water pressure, spray width, and nozzle position according to their preferences.

5.After the wash cycle, the nozzles will perform a self clean cycle purging water for approximately 5 seconds.

NOTE:

•You cannot increase the water pressure level to higher than level 2 under the following conditions: Main water supply temperature is under 50° F or if the rated power source is under 110V.

Nozzle Positioning

While the wash function is operating, use the Nozzle Position up and down arrows on the remote control to move the position of the nozzles and spray. Each nozzle has seven positions.

Water Pressure Adjustment

While the wash function is operating, press the Water Pressure “+” and “-“ buttons on the remote control to increase or decrease the water pressure of the spray. There are three water pressure levels: Low – Med – High.

OPERATING THE SWASH (cont.)

USING THE SWASH 1200/1400 (cont.)

Wide Spray

To adjust the spray width of the washing stream during a wash cycle, press the Wide Spray button. The Wide Spray button has three levels indicated by the Wide Spray Indicator Light on the remote control:

Concentrated Stream (blue), Medium Stream (pink), Wide Stream (red)

Increasing the spray width to the Medium and Wide settings will also decrease the spray pressure.

Adjusting Water Temperature

Press the Water Temp. button to adjust temperature to desired level. There are four temperature levels indicated by the Seat Temp. Indicator light

on the remote:

Off - incoming water temp., Low - 90° F (blue), Medium - 95° F (pink), High - 100° F (red)

Adjusting Seat Temperature

Press the Seat Temp. button to adjust the seat temperature to desired level. There are four temperature levels indicated by the Seat Temp. Indicator light on the remote:

Off, Low - 89° F (blue), Medium - 93° F (pink), High - 97° F (red)

Auto Function

The Auto Function will run a preset wash and dry cycle* with a simple press or hold of the “Auto” button.

Pressing the Auto button will initiate a rear wash cycle for 90 seconds at the medium (pink) water temperature. The water pressure will be set to high and the spray width will be on the medium (pink) setting. The oscillate function will start as soon as the wash cycle starts. The Swash will automatically start the Air Dryer* and run a dry cycle* for 2 minutes immediately after the wash cycle. The Dryer temperature* will be set to medium.

Press and hold the “Auto” button for 5 seconds to initiate a Front Wash cycle for 90 seconds at the medium (pink) water temperature. The water pressure will be set to high and the spray width will be on the medium (pink) setting. The oscillate function will start as soon as the wash cycle starts. The Swash will automatically start the Air Dryer* and run a dry cycle* for 2 minutes immediately after the wash cycle. The Dryer temperature* will be set to medium.

Press Stop on the remote anytime during the wash or dry cycle* to stop the Auto Function.

In “Auto” mode, the seat temperature will be unchanged; it will be set to whatever the last seat temperature setting was. The deodorizer will not turn on during the Auto Function.

NOTE:

• The Warm Air Dryer is only available on the Swash 1400 model

USING THE SWASH 1200/1400 (cont.)

User Memory Setting

The Swash User 1 and User 2 memory function allows you to program your preferred wash settings for a Front and Rear wash cycle for two users. These settings include: Water Temperature Level, Spray Width Level, Water Pressure Level, Nozzle Position, and Nozzle Oscillation*. Follow the steps below to program and use the Memory Function.

*only available on the Swash 1400 model

Programming User 1 or User 2 Memory Function

1.Sit on the seat. The seat will give an audible response letting you know that the seat sensor has been engaged (unless “Silent Mode” has been set to On). At the same time, a small amount of water will flush over the nozzle, performing an automatic self-cleaning cycle.

2.To program Front nozzle settings, press and release the Front button. To program Rear nozzle settings, press and release the Rear button. A wash cycle will commence.

a.While the wash is operating, set your desired Water Temperature Level, Spray Width Setting, Water Pressure Level, Nozzle Position, and Oscillation option.*

b.Let the wash cycle run the full two minutes or press the Stop button at any time.

3.If desired, initiate another wash cycle using the opposite nozzle.

a.While the wash is operating, set your desired Water Temperature Level, Spray Width Setting, Water Pressure Level, Nozzle Position, and Oscillation option.*

b.Let the wash cycle run the full two minutes or press the Stop button at any time.

4.Press and hold the User 1 or User 2 button on the remote for five (5) seconds to save the programming. You should hear an audible beep when the settings are programed.

Continued on next page...

OPERATING THE SWASH (cont.)

USING THE SWASH 1200/1400 (cont.)

User Memory Setting (cont.)

Using the User 1 or User 2 Memory Function

2.Press the User 1 or User 2 button followed by the Front or Rear button, depending on which wash cycle was programmed. You will hear an audible tone if you select a wash cycle that has not been programmed.

3.The nozzles will self-clean and purge a small amount of water which will last for several seconds prior to starting the programmed wash function. The Water Temperature Level, Spray Width Level, Nozzle Position, Water Pressure Level, and Oscillation function will be set to the programmed settings. The wash cycle will run for 2 minutes and shut off automatically.

4.To keep the wash continuing longer than 2 minutes, press the Front or Rear button again during the wash cycle. Each time you press the button during the wash cycle, the 2 minute wash cycle will start over again.

5.If you would like to stop the wash before the 2 minute cycle ends, press the Stop button.

IMPORTANT NOTES REGARDING USER MEMORY SETTINGS:

•After pushing the User 1 or User 2 button you have 5 minutes before the memory function is cancelled.

•If the seat sensor is de-activated at any time after pushing the User 1 or User 2 button, the memory setting function will be cancelled.

•When you use the User 1 or User 2 memory settings, the LED indicator lights on the remote may not reflect your saved preferences, but your programmed Front and Rear wash settings will be accurate and correct.

•After programing both nozzles for a User, if you decide to change the programing of one nozzle, you must reprogram both nozzles.

Auxiliary Controls

1.Power button – Turns the product On/Off. Press and hold the button for at least 2 seconds to turn off the Swash.

NOTE:

•If the Power button is pressed while front or rear wash is operating, the wash function will stop.

2.Rear Cleansing – Selects the rear wash function.

3.Nozzle Cleaning – To better clean the nozzles, press this button, the nozzle will extend fully for easy cleaning. Refer to Maintenance section for additional nozzle cleaning information.

USING THE SWASH 1400's ADDITIONAL FEATURES

Nozzle Oscillation (Move) Function

While the wash function is operating, press the Move button on the remote control to start or stop the nozzle oscillation function (moving back and forth). This provides a wider range of wash spray.

Warm Air Dryer Function

Once the wash cycle is complete, press the Dry button to activate the warm air dryer. The dryer will run for two minutes. To keep the dryer running longer than two minutes, press the DRY button again during the drying cycle to add another two minutes. If you would like to stop the dryer before the two minutes has elapsed, press Stop.

While the air dryer is operating press the Water Pressure / Dry Temp “+” and “–” to adjust the dryer temperature to a comfortable level. There are four settings: Off - Low - Medium - High.

NOTE: the Seat Sensor must be activated in order for this function to work, unless the Seat Sensor has been cancelled (see page 27 for details).

Deodorization

To activate the deodorizer, press the Deodorize button on the remote control. The deodorizer will run for one minute. To stop the deodorizer prior to completion of the cycle, press Stop.

Nozzle Sterilization

To sterilize the stainless steel nozzles, press the Sterilize button on the remote control. A cleansing silver oxide nano-particle water treatment will commence. The cleansing spray will last for 60 seconds while the nozzles extend and retract. To stop the nozzle sterilization prior to completion of the cycle, press Stop.

The Silver oxide nano-particle treatment system has powerful anit-fungal and anti-bacterial properties to keep the nozzles clean and corrosion-free. Use the sterilizing feature as often and frequently as you like. The nano-particles will never lose effectiveness and never require replacing, lasting the life of the bidet.

OPERATING THE SWASH (cont.)

SWASH SPECIAL MODE OPERATIONS

NOTE:

•Special Mode Operations can be changed following the instructions below using the Auxiliary Controls on the side of the bidet (see pages 20 and 24).

Selecting/Canceling Eco Mode

When the Eco Mode function is selected, the Swash will go into Eco Mode when the Seat Sensor is not activated and no buttons on the Remote have been active for approximately 10 minutes. The seat heater will automatically set itself to the Low temperature setting to reduce power consumption. Once Eco Mode is activated, the Eco Mode light on the seat will turn green and the other lights will turn off.

Eco Mode is cancelled at the factory by default.

1. Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously

for approximately 5 seconds until one or more of the seat display lights start flashing. Release the buttons.

NOTE: If the nightlight is turned on, it will also flash.

2.Press the Rear Cleansing button to Set or Cancel Eco Mode.

a.If the Eco Mode indicator light is flashing, this indicates Eco Mode has been set.

b.If the Eco Mode indicator light is not flashing, this indicates Eco Mode has been cancelled.

3.The new setting will automatically be saved within 10 seconds if no other buttons are pressed, or if you press the Stop button on the remote control.

Selecting/Canceling Silent Mode

By default, the Swash will beep to confirm commands from the remote control. Follow the steps below to deactivate the beeping sounds.

1. Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously

for approximately 5 seconds until one or more of the seat display lights start flashing. Release the buttons.

NOTE: If the nightlight is turned on, it will also flash.

2.Press the Power button to Set or Cancel silent mode.

a.If the Power indicator light is flashing, this indicates Silent Mode has been set. There will not be any beeping sounds when buttons on the Remote Control are pressed.

b.If Power indicator light is turned off, this indicates the Silent Mode has been canceled. Beeping sounds when buttons on the Remote Control are pressed will resume.

3.The new setting will automatically be saved within 10 seconds if no other buttons are pressed, or if you press the Stop button on the remote control.

SWASH SPECIAL MODE OPERATIONS (cont.)

Selecting/Canceling Seat Sensor Lock Mode

This function bypasses the body sensor located in the seat and allows the wash functions and dry functions to operate without the sensor being engaged. Use caution in this mode.

Seat Sensor Lock Mode is selected at the factory by default.

1. Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously

for approximately 5 seconds until one or more of the seat display lights start flashing. Release the buttons.

NOTE: If the nightlight is turned on, it will also flash.

2.Press the Nozzle Cleansing button to Set or Cancel Seat Sensor Lock Mode.

a.If the Seat Temperature indicator light is flashing, this indicates that the Seat Sensor Lock Mode has been set. Someone will need to be sitting on the seat for the unit to operate.

b.If the Seat Temp indicator light is not flashing, this indicates that the Seat Sensor Lock Mode has been cancelled. Someone does not need to be sitting on the seat for the unit to operate. Use caution.

3.The new setting will automatically be saved within 10 seconds if no other buttons are pressed, or if you press the Stop button on the remote control.

Illuminating/Exstinguishing the Night Light

By default, the night light on the Swash will be constantly illuminated. Follow the steps below to turn the night light off.

1. Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously

for approximately 5 seconds until all the seat display lights start flashing. If the nightlight is

turned on, it will also flash. Release the buttons.

2.Press the Rear Cleansing button and Nozzle Cleansing buttons simultaneously to Set or Cancel the Nightlight.

a.If the Nightlight light is flashing, this indicates that the Nightlight has been set.

b.If the Nightlight light is not flashing, this indicates that the Nightlight has been cancelled.

3.The new setting will automatically be saved within 10 seconds if no other buttons are pressed, or if you press the Stop button on the remote control.

ID Settings

The Swash 1200 and 1400 has the ability to pair a remote to a specific Swash seat. This is helpful in cases where there is more than one toilet in the bathroom. For more information on how to pair a remote to a Swash, please contact Brondell customer service.

PRODUCT SPECIFICATIONS

		BRONDELL SWASH ADVANCED BIDET SEAT

	Model	S1200-EW, S1200-RW, S1400-EW, S1400-RW, S1400-EB, S1400-RB

	Power Voltage	120 V, 60 Hz

	Power Consumption	1200 W

	Supply Water Pressure	14.5 psi – 100 psi

	Dimensions	Elongated: 15.2 in x 20.43 in x 5.75 in
	Dimensions	Round: 15.2 in x 19.75 in x 5.75 in
		Round: 15.2 in x 19.75 in x 5.75 in

	Weight	Elongated: 14.3 lbs / Round: 13.2 lbs

	Remote Control	2.17 in x 6.1 in x 0.8 in
	Dimensions	with Holster: 2.58 in x 6.5 in x 0.9 in

	Seat / Lid Weight Limit	330 lbs / 270lbs.

	Operating Temperature	32° F – 104° F

	Mesh Filter	0.74 in x 0.5 in diameter

		WARM WATER WASHING DEVICE

	Rear Wash	Maximum 0.13 gal per minute, automatic nozzle self-cleaning

	Front Wash	Maximum 0.13 gal per minute, automatic nozzle self-cleaning

	Standard Time	Rear Wash: 2 minutes / Front Wash: 2 minutes

	Water Pressure Control	3 Levels

	Water Temperature	4 Levels: Off - incoming water temperature,
	Control	Low - 90° F, Medium - 95° F, High - 100° F

	Heater Power	1200W
	Consumption	1200W
	Consumption

	Safety Devices	Bimetal, temperature sensor,
	Safety Devices	temperature fuse (overheating prevention)
		temperature fuse (overheating prevention)

		HEATED SEAT

	Seat Temperature	4 Levels: Off - room temperature
	Control	Low - 89° F, Medium - 93° F, High - 97° F

	Heater Power	50 W
	Consumption	50 W
	Consumption

	Safety Devices	Bimetal, temperature sensor

NOTE:

The specifications listed above are subject to change without prior notice for reasons of improving the product performance.

+ 82 hidden pages