OWNER’S MANUAL
Swash CL510 Advanced Bidet Toilet Seats
CL510-EW
CL510-RW
Attach Proof of Purchase to This Page
Adjunte prueba de compra a esta página
CONTENTS
This manual contains important safety information. Before operating the bidet, please read this manual thoroughly, and retain it for future reference.
|
GENERAL INFO |
|
TECHNICAL INFO |
02 |
SAFETY INFORMATION |
19 |
PRODUCT SPECIFICATIONS |
06 |
PRODUCT INFORMATION |
20 |
MAINTENANCE |
06 |
Product Features |
20 |
Seat Cleaning & Removal |
07 |
Product Dimensions |
20 |
Nozzle Cleaning |
08 |
Product Parts |
21 |
Cleaning the Mesh Filter |
|
|
21 |
Product Storage & Use |
PRODUCT INSTALLATION |
22 |
TROUBLESHOOTING |
|
25 |
WARRANTY |
||
09 |
PRODUCT INSTALLATION |
26 |
CONTACT |
09Installation Parts
10Before Installation
10 Swash Installation
13 External Bidet Filter Installation |
TRANSLATIONS |
|
|
|
27 SPANISH |
PRODUCT OPERATION
14 OPERATING THE SWASH
14 CL510 Control Panel
16 Using the Swash CL510
18 Special Mode Operations
1
SAFETY INFORMATION (IMPORTANT SAFEGUARDS)
Be careful to keep this safety information. Please read this information to prevent property loss and ensure safety.
DANGER:
If not observed, serious injury or even death may occur as a result.
WARNING:
If not observed, serious physical injury or property damage may occur as a result.
CAUTION:
If not observed, minor physical injury or property damage may occur as a result.
READ ALL INSTRUCTIONS BEFORE USING
DANGER
Failure to observe the following warnings may result in electric shock, fire, personal injury, property damage or product damage:
• Do not use a damaged power plug or plug into a loose electric outlet. • Do not move the product by pulling the power cord.
• Do not handle the product or power plug with wet hands.
• Do not forcefully bend the power cord or place heavy objects on it to prevent it from being damaged or deformed.
• Do not connect and pull out the power plug or cord repeatedly.
• Unplug the product before cleaning, repairing, inspecting, or replacing parts. • Remove any dust or water from the power plug prior to plugging in.
• Do not plug the product into an electrical outlet or power strip that is being used by too many other products. Use an electrical outlet adequate for the wattage of the product rated for a minimum of 15 amps.
• If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself. Contact the Brondell Service Center toll free at 888-542-3355 or email us through our website.
• If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately from the electrical outlet and contact Brondell. Failure to do so may result in electric shock or fire.
• Do not insert any wires or sharp objects into any product gaps. This may result in electric shock, fire, or product damage.
SAVE THESE INSTRUCTIONS
2
SAFETY INFORMATION (cont.)
(IMPORTANT SAFEGUARDS)
DANGER
• Do not place an electronic or gas heater near the product or dispose of any burning materials such as a lit cigarette in the toilet. This may result in fire or product deformation. Do not place any
containers filled with water or other liquids, food, metallic objects, or any flammable material on top of the product. If foreign material enters the product, this may result in electric shock or fire.
• Do not use the product in locations exposed to excessive moisture and do not splash water onto the product.
• While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise caution to ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so may result in electric shock or fire.
• If foreign material enters the product, pull the power plug out of the electrical outlet, turn off the main water valve, and call the Brondell Service Center.
• Do not disassemble, repair, or modify the product yourself. • Do not use the product while wet from bathing or showering.
• Do not place or store the product where it can fall or be pulled into a tub or sink. • Do not place in or drop the product into water or any other liquid.
• Do not reach for the product if it has fallen into water. Unplug the product immediately and call the Brondell Service Center.
• Do not use the product if it is not working properly. Please unplug the product immediately, close the main water supply valve, and call the Brondell Service Center at 888-542-3355. Failure to do so may result in electric shock, fire, or flooding.
WARNING
Failure to observe the following warnings may result in electric shock, fire, personal injury, property damage or product damage.
• Do not plug in, operate, or store the unit in locations where flammable or combustible materials are used or kept.
• Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease. • Turn off the main water supply valve when cleaning.
• For children and seniors who may have difficulties with adjusting temperatures or those with sensitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low” or “off” to prevent burning.
• Close supervision is necessary when this product is used by children, seniors, or persons requiring general assistance.
• Do not press the buttons using excessive force.
• Do not stand on top of or place any heavy objects onto the seat cover.
• Use this product for its intended use only, as described in this manual. Do not use any attachments that are not recommended by Brondell.
SAVE THESE INSTRUCTIONS
3
SAFETY INFORMATION (cont.)
(IMPORTANT SAFEGUARDS)
WARNING
• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact the Brondell Service Center for examination and repair.
• Keep the cord away from heated surfaces and heating vents.
• Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, etc.
• Never drop or insert any object into any opening or hose.
• Do not use the product outdoors or operate where aerosol (spray) products are being used or a room where it could be exposed to oxygen.
• Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in the next pages of the manual.
CAUTION
Failure to observe the following warnings may result in electric shock, fire, personal injury, property damage, or product damage.
• Do not connect the main water supply to the hot water pipe or supply (only connect to the cold water supply).
• After the installation, make sure to check all water supply connections for leaks. Rubber washers should be in place for the water connection hoses & T-Valve.
• Do not open/close the seat or seat cover with excessive force.
• Exercise caution that urine does not come into contact with the product - failure to do so may result in bad odors or malfunction.
• If the product will not be used for a long period of time, unplug the power cord, close the main water supply valve, and drain any water in the water tank.
• Do not pull out the bidet hose using excessive force.
• Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or near the product. This may result in corrosion to the metal parts or discoloration or scratches to the bidet body.
• This appliance is not intended for use by persons (including children and seniors) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS
4
SAFETY INFORMATION (cont.)
(IMPORTANT SAFEGUARDS)
GROUNDING AND GFI OUTLET INSTRUCTIONS
This product should only be used with a grounded GFCI (Ground Fault Circuit Interrupter) outlet and a grounded three-prong electrical cord as shown to the right. In the event of an electrical short circuit, using a grounded GFCI outlet reduces the risk of electric shock.
This product is equipped with a grounded cord and is for use on a nominal 120V circuit only (minimum 15 amps) and must be plugged into an outlet that is properly grounded with a GFCI breaker as shown. Replace or repair a damaged cord immediately.
Ground GFCI Outlet
Grounding Pin
Test
Reset
Improper use of the grounding plug can result in a risk of electric shock.
• If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with green insulation (either with or without a yellow stripe) is the grounding wire.
• Check with a qualified electrician if the grounding instructions are not completely understood, or if there is doubt if the product is properly grounded.
Extension Cord Use
If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps with a three-wire extension cord with a three-blade grounding plug. Only plug into a three-slot grounded GFCI receptacle that will accept the plug of the product. Replace or repair any damaged cords immediately.
SAVE THESE INSTRUCTIONS
5
PRODUCT INFORMATION
PRODUCT FEATURES
Stainless-Steel Nozzle System - Stainless steel resists soiling and bacterial contamination for enhanced hygiene.
Posterior and Feminine Warm Water Wash – experience the ultimate in clean with adjustable temperature, position, pressure, massage, and oscillation settings.
Positionable Nozzle – the nozzle has five different positions to ensure the most comfortable and complete wash.
Adjustable Water Temperature and Pressure – each wash mode (Front and Rear) has four available water temperature settings, and five water pressure settings.
Massage – when activated, the water pressure automatically increases and decreases to provide a pulsating, cleaning spray.
Warm Air Dryer – includes adjustable temperature with five levels for a hands-free experience and toilet paper reduction – even elimination.
Nozzle Oscillation – the Move function provides a massaging, oscillating cleanse during the wash cycle ensuring a thorough and comfortable wash.
Auto Function – activates a preset for a rear wash cycle followed by a drying cycle.
Ergonomic Heated Seat – with four temperature settings (High/Med/Low/Off).
Illuminating Nightlight – the cool blue hue of the nightlight means no more blinding lights during midnight trips to the bathroom.
Gentle-Closing Seat and Lid – “slam free” gentle closing seat and lid are user friendly.
Eco Mode – when activated, this function automatically lowers the water and seat temperature.
6
PRODUCT DIMENSIONS
Elongated Top View
4.3 in |
16.4 in |
|
|
7.8 in |
14.9 in |
||
|
|
||||
|
|
|
|
|
18.2 in |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2.7 in
13.6 in
Round Top View
4.3 in |
15.2 in |
|
|
7.8 in |
14.9 in |
||
|
|
||||
|
|
|
|
|
18.2 in |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2.7 in
13.6 in
Required Distance Between
Mounting Holes
5.5 in
7
PRODUCT INFORMATION (cont.)
PRODUCT PARTS
|
1. |
Lid |
|
2. |
Seat Sensor |
|
3. |
Warm Seat |
|
4. |
Warm Air Dryer |
1 |
5. |
Nozzle Assembly |
|
6. |
LED Nightlight |
|
7. |
Control Panel |
|
8. |
Power Plug |
|
9. |
Water Inlet with Mesh Filter |
|
10. |
Drain Plug |
8 |
11. |
Mounting Plate |
|
|
|
|
2 |
|
|
3 |
|
4 |
|
|
5 |
|
|
7 |
|
|
6 |
|
10 |
|
|
|
|
|
9 |
11 |
|
|
8
PRODUCT INSTALLATION
INSTALLATION PARTS
1. |
Mounting Bolt (2) |
6. |
Top-Mount Brackets (2) |
2. |
Rubber Cone Washer (2) |
7. |
T-Valve Connector with |
3. |
Flat Washer (2) |
|
Rubber Washer |
4. |
Nuts (2) |
8. |
Bidet Hose |
5. |
Mounting Plate |
|
|
1 |
7 |
8 |
2
3
4
5
6
9
PRODUCT INSTALLATION (cont.)
BEFORE INSTALLATION
DO NOT PLUG THE PRODUCT IN WHILE THE UNIT IS UPSIDE DOWN
This may cause damage to the internal components.
WATCH OUR INSTALLATION VIDEO
Installation for all Swash products can be found online at brondell.com
CHECK BOLT SPREAD
This bidet can only be installed on toilets with a bolt hole spread of 5.5 inches (see Product Dimensions on Page 7 for more information).
CHECK FOR TOP MOUNT INSTALLATION
If your fixture only has top-side access to the mounting bolts that hold the seat to the toilet, include the Top-Mount Brackets included in the hardware pack (see Page 12).
CHECK FOR A CONCEALED TOILET FILL VALVE
Many modern toilets have sleek designs intended to cover and camouflage plumbing connections, which makes a standard Swash installation difficult or impossible. For this, we recommend using our Alternate Swash Bidet Seat T-Valve, found on brondell.com.
CHECK WATER SUPPLY LINE
Check the line that connects the toilet tank to the water shut off valve. If it is a rigid pipe, you may need to purchase a flexible hose to replace it before installing the Swash. The length of the hose and the size of the connectors will vary.
RESIDUAL MOISTURE IS NORMAL
Every product is tested with pure water during production to ensure the highest quality and performance. It is normal to find a small amount of residual moisture on the product and in the reservoir and filter.
TOOLS
A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a standard wrench may be needed for tight water supply connections. Teflon tape can be helpful in creating a water-tight seat between plumbing connections.
SWASH INSTALLATION
Please read these instructions carefully before installing the Swash. Failure to do so could result in flooding, leaking or damage to the product.
1.Existing Toilet Seat Removal
a.Lift hinge covers and use a screwdriver to remove the mounting bolts.
b.Remove the toilet seat. Keep for future use.
10
SWASH INSTALLATION (cont.)
NOTE: Steps may vary by type of seat and toilet
2.Turn Off Water Supply Valve and Flush Toilet
a.Turn water valve off to stop the flow of water.
b.Flush toilet and hold down handle to completely empty tank.
c.Disconnect water supply hose from toilet tank. Do not disconnect from the water supply valve.
NOTES:
•You may wish to place a container under the tank to catch any excess water.
•Do not continue without completing the above steps
•Failure to do so could result in flooding, leaking or damage to the Swash.
3.Connect the top of the T-Valve to the incoming water connection on the bottom of your toilet tank.
NOTES:
•The T-Valve connects to the fill valve directly under your toilet tank - it does not connect at the wall.
•Only connect to the cold toilet water supply line.
•If your water supply line is rigid you may need to replace it before continuing.
4.Connect the water supply line coming from the wall to the bottom of the T-Valve
5.Install Mounting Plate for Standard Installation (see Page 12, Step 6 for instructions on using the Top-Mount Brackets)
a. Place adjustable mounting plate over mounting holes on toilet, rubber side facing down, arrow pointing to the toilet bowl.
b. Insert the mounting bolts through the mounting plate and mounting holes of the toilet. Be sure that the square mounting bolt head is even with the sides of the mounting plate.
c. Slide rubber cone washer, flat washer, and then nut onto mounting bolts under the toilet bowl and tighten to keep mounting plate in place.
Step 2c
toilet tank
t-valve
cold water 
supply line 
Steps 3-4
Steps 5b & 5c
11
PRODUCT INSTALLATION (cont.)
SWASH INSTALLATION (cont.)
6.Install Mounting Plate for top-mounted toilet seats (see Page 11, Step 5 for instructions on Standard Installation). This method will use a combination of the included TopMount Brackets and the original toilet seat mounting bolts.
a.Place adjustable mounting plate over mounting holes on toilet, rubber side facing down, arrow pointing to the toilet bowl.
b.Place the provided Top-Mount Brackets flat side down into the slots of the Mounting Bracket, over the bolt holes.
c.Insert the original toilet seat mounting bolts through the Top-Mount Brackets and into the threaded bolt holes of the toilet, using a screwdriver to tighten.
7.Connect the Bidet Hose to the Seat
a.Connect the elbow side of the bidet hose to the water inlet. Hand-tighten to secure. Take care not to twist the bidet hose, excessively bend it, or strip the plastic screw threads when screwing the hose onto the bidet seat.
8.Attach the Swash to the Mounting Plate
a.Set the Swash flat on the toilet bowl in front of the mounting plate, and slide seat onto plate until it is secure.
b.If the seat appears too short or too long for the toilet, adjust the mounting plate accordingly. To adjust the mounting plate, loosen the nuts underneath the toilet and slide seat forward or backwards as needed. Once the seat is lined up properly, tighten the nuts to hold in place.
9.Connect the open end of the Bidet Hose to the T-Valve.
10.Turn On Water Supply
a.Open the main water supply valve slowly and check for leaks.
b.Wait 5 minutes, check again and if there are no leaks continue.
11.Plug the Power Cord into an Electrical Outlet
a.If the Power Indicator is not illuminated press any button on the control panel.
Steps 6b & 6c
Step 7a
Step 8b
Step 9
12
SWASH INSTALLATION (cont.)
NOTES:
•Make sure to only use a grounded GFCI (ground fault circuit interrupter) electrical outlet. In the case of a short circuit, a grounded GFCI outlet may help prevent electric shock or injury.
•If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps with a three-wire extension cord with a three-blade grounding plug.
12.Press the “REAR WASH” button on the control arm to fill the water tank. The bidet will beep continuously while it fills and then issue one long beep when the water tank is full. Wait 3-5 minutes for the water to heat, and then the Swash will be ready to use.
13.Follow instructions on Page 16 for using the Swash.
EXTERNAL BIDET FILTER INSTALLATION
NOTE:
•Customers with hard water, well water, and softened water can extend the life of their bidet seat by purchasing and installing an external inline water filter to be used with the Swash. The bidet filter should be changed every six months, and can be purchased online at brondell.com.
1.Turn Off Water Supply Valve and Flush Toilet. a. Turn water valve off to stop the flow of water.
b. Flush toilet and hold down handle to completely empty tank.
2.Disconnect the Bidet Hose from the T-Valve
3.Connect the female end of the Swash Filter to the open T-Valve connection.
4.Connect the Bidet Hose to the male end of the Swash Filter.
5.Turn the toilet water supply valve back on.
FLOW FLOW
Step 2 Step 3 Step 4
13
OPERATING THE SWASH
CL510 CONTROL PANEL
Seat Temperature |
9 |
Button and Indicators |
|
Water Temperature |
8 |
Button and Indicators |
|
Nozzle Position Buttons |
7 |
Water Pressure and |
6 |
Dry Temperature |
|
Buttons and Indicators |
|
Massage Button |
5 |
Warm Air Dry Button |
4 |
Front Wash / |
3 |
Move Button |
|
Rear Wash / |
2 |
Move Button |
|
Stop Button |
1 |
10 Power Indicator
11 Eco Mode Button
and Indicator
12 |
Night Light Button |
|
and Indicator |
13 Auto Mode Button
14
CL510 CONTROL PANEL (cont.)
1. Stop Button
Stops all wash and dry functions currently operating. Press and hold this button for four seconds to power off the bidet.
2. Rear Wash / Move Button
Press once to initiate a rear wash. Press again to initiate nozzle oscillation (repetitive forward and backward nozzle movement).
3. Front Wash / Move Button
Press once to initiate a front wash. Press again to initiate nozzle oscillation (repetitive forward and backward nozzle movement).
4. Dry Button
Press once to initiate a two minute Warm Air Dryer cycle.
5. Massage Button
Pressing this button while a wash is running enables the water to repeatedly increase and decrease in pressure in a pulsating pattern. Press again to stop the massage.
6. Water Pressure and Dry Temperature Buttons and Indicators
Press the “+” and “–” buttons to increase and decrease the outgoing water pressure to one of five settings. Pressing these buttons while the Warm Air Dryer is operating will adjust the Drying temperature. Settings will be saved for the next use.
7. Nozzle Position Buttons
Press the arrow up and arrow down buttons to adjust the nozzle position forward and backward during a wash cycle. Between uses the nozzles will revert back to the middle position.
8. Water Temperature Button and Indicators
Press and release the “Water Temp” button to adjust the outgoing water temperature to one of four settings (LO: 93.2° F, MED: 98.6° F, HI: 104° F, and OFF). Settings will be saved for the next use.
9. Seat Temperature Button and Indicators
Press and release the “Seat Temp” button to adjust the seat temperature to one of four settings (LO: 95° F, MED: 100.4° F, HI: 104° F, and OFF). Settings will be saved for the next use.
10. Power Indicator
This indicator will light up when the bidet is powered on, and will be off when the bidet is powered off. To turn off the bidet press and hold the “STOP” button for at least four seconds.
11.Eco Mode Button and Indicator
Press and release the “Eco Mode” button to select or turn off Eco Mode. The indicator will light up when the Eco Mode has been selected. See Page 17 for more information.
12.Night Light Button and Indicator
Press the “Night Light” button to enable the Night Light (the indicator light will be illuminated). Press again to disable the Night Light and indicator.
13. Auto Mode Button
Press this button once to initiate a one minute rear wash cycle followed by a one minute dry cycle. See Page 17 for more information.
15
Loading...