Broilmaster BHAX-1, BDA-1, BBA-1, BRB-1, BSA-1 User Manual 2

Built-in Kit Owners Manual
BHa-1, BHaX-1, BBa-1, Bsa-1, BDa-1 anD BrB-1 Kits
OutDOOr Grill MOuntinGs
FOr use witH P3, r3, H3 Or t3 series BrOilMaster PreMiuM Gas
Grills
instructiOns Must Be leFt witH tHe Owner FOr Future reFerence aFter installatiOn.
retain Owners Manual FOr Future reFerence.
GAS-FIRED
Page 1
THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY.
iMPOrtant
we aDvise yOu tO careFully reaD anD FOllOw tHe instructiOns in tHis Owners Manual BeFOre
installinG Or usinG yOur new BrOilMaster yOur Built-in Kit will OFFer years OF cOOKinG satisFactiOn. tHe installer sHOulD Present yOu witH tHis Manual. Please retain it FOr Future reFerence.
warninG
reFerence tHis Manual FOr PrOPer installatiOn anD Maintenance instructiOns. iMPrOPer
installatiOn, aDjustMent, alteratiOn, service Or Maintenance can cause PersOnal injury Or PrOPerty DaMaGe. FOr assistance Or aDDitiOnal inFOrMatiOn cOnsult a qualiFieD installer, service aGency Or tHe Gas suPPlier.
FOr yOur saFety
iF yOu sMell Gas:
1. sHut OFF Gas tO tHe aPPliance.
2. eXtinGuisH any OPen FlaMe.
3. OPen tHe Grill liD.
4. iF ODOr cOntinues, iMMeDiately call yOur Gas suPPlier Or Fire DePartMent.
5. DO nOt tOucH electrical switcHes.
®
Built-in Kit. wHen installeD anD useD as recOMMenDeD,
FOr yOur saFety
1. DO nOt stOre Or use GasOline Or OtHer FlaMMaBle vaPOrs anD liquiDs in tHe vicinity OF tHis Or
any OtHer aPPliance.
2. an lP cylinDer nOt cOnnecteD FOr use sHall nOt Be stOreD in tHe vicinity OF tHis Or any OtHer
aPPliance.
FOr yOur saFety
Be careFul wHen HanDlinG Parts DurinG asseMBly anD use as tHey May cOntain sHarP eDGes.
wOrK GlOves are HiGHly recOMMenDeD tO HelP Prevent POssiBle injury.
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact Broilmaster® Customer Service at 800-851-3153 • WWW.broilmaster.com. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model number of your Single Door, Part Name, Part Number, and Quantity of parts needed.
Page 2 B101502-3-1012
taBle OF cOntents
Congratulations!
You have chosen the nest Built-In Kit for your outdoor cooking pleasure. Please take time to read this entire manual before assembling your premium Broilmaster Built-In Kit.
Location, Connections, and Safety ................................................................................................ 3 - 4
Enclosure Construction Guidelines .................................................................................................... 5
BHA & BHAX Grill Surround ........................................................................................................ 6 - 10
BBA Tank Caddy ........................................................................................................................ 11 - 14
BSA Side Burner Surround ........................................................................................................ 15 - 17
BDA Single Door........................................................................................................................ 18 - 21
BRB Vent Register Kit ...............................................................................................................22 - 23
Warranty ........................................................................................................................................... 24
Your Broilmaster® accessory is identied by model number, serial number, and gas type. This information is provided on a product identication label located on the accessory. The grill’s model number, serial number, and gas type must also be provided when contacting your Broilmaster® dealer. For your convenience, complete this section for future reference when contacting your dealer.
Model No. Dealer
Serial No. Dealer Phone No.
Gas Type: Propane Natural Date of Purchase
Page 3B101502-3-1012
lOcatiOn, cOnnectiOns, anD saFety
Built-In Kit Location
Built-In Kits are designed for outdoor use ONLY.
This Built-In Kit is designed for use with all P3 and T3 Model Broilmaster® gas grills and cannot be used with any other grill or in any other capacity.
Never install or operate your Built-In Kit in any building,
garage, or other enclosed area.
For your safety, the Built-In Kit should not be installed or operated under any combustible materials, such as carports, covered porches, awnings, or overhangs.
Never install or use your Built-In Kit in or on any recreational vehicle or boat.
CAUTION: THE INSTALLATION AND OPERATION OF THIS BUILT-IN KIT AT CLEARANCES LESS THAN
SPECIFIED BELOW MAY LEAD TO THE POSSIBILITY OF
FIRE, PROPERTY DAMAGE, OR PERSONAL INJURY.
A minimum clearance of twenty-four (24”) inches is required from all sides of the island to any combustible material.
Examples of combustible materials are patio furniture, fences, or the outside of your home.
The area surrounding the built-in kit should be clear to ensure proper ventilation. Do not obstruct the ow of combustion and ventilation air in any way. The ventilation openings on the enclosure must also remain free and clear of debris.
WARNING: DO NOT INSTALL OR OPERATE THIS BUILT­IN KIT WHERE GASOLINE OR OTHER FLAMMABLE
MATERIALS ARE USED OR STORED. FAILURE TO
COMPLY WITH THIS WARNING COULD RESULT IN
EXPLOSION OR FIRE CAUSING PROPERTY DAMAGE OR PERSONAL INJURY.
CAUTION: THE GRILL AND ITS INDIVIDUAL SHUTOFF VALVE MUST BE DISCONNECTED FROM THE GAS SUPPLY PIPING SYSTEM DURING ANY SYSTEM PRESSURE TESTING AT TEST PRESSURES IN EXCESS OF 1/2 PSIG.
Checking for Gas Leaks
CAUTION: DO NOT USE AN OPEN FLAME TO CHECK
FOR LEAKS. CHECKING FOR LEAKS WITH AN
OPEN FLAME MAY LEAD TO A FIRE OR EXPLOSION, RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY.
Using the following steps, check for gas leaks during initial use and each time your Broilmaster® gas grill or side burner
is connected to gas or is connected to a cylinder that has
not been used recently
1. Using dish washing detergent and water, make a soapy
solution.
2. Turn OFF the knob on both the grill and side burner’s control panel.
3. Turn ON the gas at the supply. A hissing sound indicates a leak. Turn OFF the gas and repair all leaks.
4. If no hissing occurs, apply the soapy solution to all gas
connections.
5. Look for bubbles. Bubbles indicate a leak.
6. If there are bubbles, turn OFF the gas and repair all
leaks.
7. Turn the gas ON and repeat the above procedure until all leaks are repaired.
Connection Requirements
CAUTION: NEVER USE LIQUID PROPANE GAS IN A GRILL DESIGNED FOR NATURAL GAS, OR NATURAL GAS IN A GRILL DESIGNED FOR LIQUID PROPANE GAS. QUESTIONS REGARDING DIFFERENT TYPES OF GASES SHOULD BE DIRECTED TO YOUR LOCAL GAS COMPANY.
Installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. In Canada, installation shall be in accordance with CAN/CGA-B149.2 Propane Installation Code, or CAN/ CGA-B149.1 Natural Gas Installation Code, and local codes where applicable. Consult your local gas company or Propane gas dealer for code regulations and recommended procedures.
Broilmaster® gas grills and side burners are NOT equipped with pressure regulators. Your Nat. gas grill operates at a manifold pressure of seven (7”) inches water column.
Page 4 B101502-3-1012
enclOsure cOnstructiOn GuiDelines
Enclosure must be construction from non-combustible material.
If tile is used on the top surface of your enclosure, it may be necessary to enlarge openings at the top edges to allow the frame pieces of the BHA and BSA to mount ush against the enclosure.
Screws for enclosure mounting have been supplied. Installer must measure for thickness and use appropriate hardware for installation. If the enclosure is constructed from masonry materials, it may be necessary to substitute appropriate screws
and fasteners.
This diagram is only a basic plan for constructing an enclosure for your built-in kit. All construction and installation should comply with all local building codes and requirements.
MINIMUM REQUIREMENTS
Key Dimension in Inches Key Dimension in Inches
A 38” (Minimum) O 14” (Single) - 27 1/2” (Double)
B 16” (Minimum) P 15 7/8” (Single) - 9 1/8” (Double)
C 28” (Minimum) Q 13 15/16”
D 26 13/16” R 5” (Minimum)
E 10 11/32” S 24 13/16”
F 12 3/16” T 24 3/4”
G 6” (Minimum) U 10”
H 15 3/8” V 2 1/4”
J 14” W 2 3/4”
K 19 13/16” X 9”
L 2 1/2” Y 1 13/16”
M 1 11/16” Z 14 3/8”
N 22 3/8” (Single) - 15 5/8” (Double)
Page 5B101502-3-1012
BHa-1 & BHaX-1 Grill surrOunD Kits
installatiOn instructiOns
nOtice: reFer tO tHe Built-in Kit enclOsure cOnstructiOn GuiDe On PaGe 5 FOr PrOPer
DiMensiOns OF tHe OPeninG FOr tHe BHa-1 Grill surrOunD Kit
Page 6 B101502-3-1012
BHa-1 & BHaX-1 Grill surrOunD eXPlODeD view & Parts list
All repair part orders should be placed through your local Broilmaster
®
dealer. To locate a dealer in your area, contact
Broilmaster Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity of parts needed.
5
1
2
3
8
4
9
6
7
Index No. Part No. Description Quantity
1 R2737 10 x 1/2 Phillips Head Screw 1
2 B101206 Flexline Bracket 1
3 B101205 Flexline 1
4 B101200 BHA Assembly 1
4 B101529 BHAX Assembly 1
5 B101022 8 x 3/4” Hex Head Screw 8
6 B101178 Grease Tray 1
7 B101204 Control Housing Assembly - BHA 1
7 B101530 Control Housing Assembly - BHAX 1
8 B100113 1/4 - 20 x 1 1/4 Screw (use only with T3/P3 Sereis grill heads) 4
9 B060337 Grease Cup 2
Verify that all parts listed on the exploded view of this manual have been included in this
Built-In Kit before beginning installation.
Caution: Use caution when handling parts, as they may contain sharp edges.
Work gloves are recommended to prevent injury.
Tools Required: Phillips Head Screw Driver (An electric screw driver or drill is recommended to ease installation)
Page 7B101502-3-1012
BHa & BHaX asseMBly
Attention: If applicable, remove protective lm from parts before installation.
1. Remove the surround from the shipping box and place the BHA surround into position in the constructed
enclosure. See Figure 1.
3. Place the grease tray into BHA surround by sliding it under the bracket. See Figure 3.
BHA ASSEMBLY
GREASE TRAY
Figure 3
4. Place the control housing assembly into BHA surround
and secure it to the BHA surround. See Figure 4.
BHA ASSEMBLY
Figure 1
2. Secure the BHA surround to the enclosure using eight
(8) 8 x 3/4” Hex Head Screw screws. See Figure 2. Note: If you have a masonry structure you may need to substitute for the appropriate masonry fasteners.
CONTROL HOUSING ASSEMBLY
Figure 4
5. Attach the ex line to the bottom of the BHA surround using the ex line bracket and screw. See Figure 5.
Figure 2
Figure 5
Page 8 B101502-3-1012
BHa & BHaX asseMBly
6. After insuring that all the contents are removed from the inside of the grill, install the grill in the BHA surround by slightly tilting the grill forward and placing it on the top of the support bracket. See Figure 6.
Figure 6
7. Mount the grill to the BHA surround using four 1/4-20 x
1 1/4” screws. See Figure 7.
8. Check for gas leaks as discussed in the “Checking for
Gas Leaks” Section of this manual on page 4.
9. Open control housing and connect ex line to the main
valve, then close the control housing door. Figure 8.
Figure 7
Figure 8
Refer to your Grill Head Installation Instructions to com­plete installation of your Broilmaster grill.
Page 9B101502-3-1012
BHa & BHaX asseMBly
10. Install each of the four vent covers (BRB Vent Register Kit) into the Built-In Kit Enclosure using two #8 x 3/4” screws. See Figure 9.
Alternate Match Lighting Instructions
1. Turn the burner control knobs clockwise to the OFF position.
2. Turn ON gas at the source.
3. Open the grill lid.
4. Open the BHA access door. Locate the Ignitor Rod, which is permanently attached to the inside of the Bottom Shelf.
5. Insert an unlit match into the coiled end of the ignitor rod. Light the match.
6. Insert the ignitor rod inside the access door and through the front left air hole located on the bottom of the grill. Position the match near the rear left corner of the burner.
See Figure 10.
7. Turn the left burner control knob counterclockwise to HI.
8. If the burner fails to light after 5 seconds, turn the burner control knob OFF for ve minutes then repeat the procedure.
9. If the burner continues not to light, turn OFF all gas and refer to the troubleshooting section of your grill Owner’s
Manual.
Figure 9
Figure 10
Page 10 B101502-3-1012
BBA-1 TANK CADDY
INSTALLATION INSTRUCTIONS
nOtice: reFer tO tHe Built-in Kit enclOsure cOnstructiOn GuiDe FOr PrOPer DiMensiOns
OF tHe OPeninG FOr tHe BBa-1 tanK caDDy.
T
HE BBA TANK CADDY IS DESIGNED TO BE USED AS EITHER AN ENCLOSURE FOR A PORTABLE
PROPANE TANK OR A GARBAGE RECEPTACLE. PLEASE REFER TO THE APPROPRIATE SECTIONS OF THIS
MANUAL FOR PROPANE TANK REQUIREMENTS, CONNECTIONS, AND SAFETY.
Page 11B101502-3-1012
BBa tanK caDDy eXPlODeD view anD Parts list
All repair part orders should be placed through your local Broilmaster contact Broilmaster® Customer Service at 800-851-3153 • WWW.broilmaster.com. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model number of your Single Door, Part Name, Part Number, and Quantity of parts needed.
3
®
dealer. To locate a dealer in your area,
1
2
PARTS LIST
Index No. Part No. Description Quantity
1 B101180 BBA Frame Assembly 1 2 B101181 BBA Door Assembly 1 3 B101022
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN
THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION.
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.
8 x 3/4” Hex Head Screw
8
Page 12 B101502-3-1012
BBA TANK CADDY INSTALLATION
Recommended Tools: Phillips Screw Driver or an electric screw driver.
1
Make sure BBA Tank Caddy opening dimensions match those in FIGURE 1. Place the BBA Frame Assembly in the Built-In Enclosure.
Secure the BBA Frame to the Enclosure with eight (8)
8 x 3/4” Hex Head screws as shown in FIGURE 1
Note: The hinge pins on the BBA Frame will be located near the bottom of the Built-In Enclosure when properly installed. Also See the proper dimensions of the opening in FIGURE 1
13 15/16”
2
While positioned on its side, place the BBA Door Assembly into the BBA Frame opening. FIGURE 2.
BBA FRAME ASSEMBLY
BBA DOOR ASSEMBLY
FIGURE 2
2413/16”
BBA FRAME ASSEMBLY
SCREWS (8)
BUILD IN ENCLOSURE
3
Once located inside the BBA Frame, rotate the BBA Door to the upright position. FIGURE 3.
FIGURE 1
FIGURE 3
Page 13B101502-3-1012
BBA TANK CADDY INSTALLATION
4
Lower the BBA Door Assembly onto the two hinge pins inside the lower left and right sides of the BBA Frame. FIGURE 4 .
HINGE PIN
FIGURE 4
ENCLOSURE REQUIREMENTS
The enclosure design must be constructed to allow only storage of the LP cylinder in use thus preventing storage of a second cylinder. Tank caddy must be provided for use in the enclosure when employing the propane self-contained system so as to prevent the lateral movement of the propane tank cylinder from its
enclosure.
An enclosure for a LP gas cylinder shall be ventilated by openings at the level of the cylinder valve and at oor level. The effectiveness of openings(s) for purposes of ventilation shall be determined with the LP gas supply cylinder in place. This shall be accompanied by one of the following: enclosure with one side completely open; or enclosure having four sides, a top and a bottom. Refer to the Built-In Kit enclosure construction guide for proper dimensions of the opening for the
BBA-1 Tank Caddy.
less than a total free area of 10 square inches (64.5 cm
2
).
2. Ventilation opening(s) shall be provided at oor
level and shall have a total free area of not less
than 1/2 square inch per pound (7.1 cm
2
/kg) of stored fuel capacity and not less than a total free area of 10 square inches (64.5 cm
2
). If ventilation openings at oor level are in a side wall, there shall be at least two openings. The bottom of the openings shall be at oor level and the upper edge no more than 5 inches (127 mm) above the oor. The openings shall be equally sized, spaced at 180 degrees (3.14 rad) and unobstructed.
3. Every opening shall have minimum dimensions so as to permit the entrance of an 1/8 inch (3.2 mm) diameter rod.
The cylinder valve shall be readily accessible for hand operation. A door on the enclosure to gain access to the cylinder valves is acceptable, provided it is non­locking and can be opened without the use of tools.
The enclosure for the LP gas cylinder shall isolate
the cylinder from the burner compartment to provide shielding from radiant heat, a ame barrier, and protection from foreign material, such as hot drippings.
There shall be a minimum clearance of 2 inches (50.8 mm) between the oor of the LP gas cylinder
enclosure and the ground.
The design of the outdoor cooking gas appliance shall be such that the LP gas cylinder can be connected, disconnected and the connections inspected and tested outside the cylinder enclosure; and those connections which could be disturbed when installing the cylinder in the enclosure can be leak tested inside
the enclosure.
1. At least two ventilation openings at cylinder valve level shall be provided in the side wall, equally sized, spaced at 180 degrees (3.14 rad), and unobstructed. Each opening shall have a total free area of not less than 1/2 square inch per pound
2
(7.1 cm
Page 14 B101502-3-1012
/kg) of stored fuel capacity and not
BSA-1 SIDE BURNEr surrOunD Kit
INSTALLATION INSTRUCTIONS
nOtice: reFer tO tHe Built-in Kit enclOsure cOnstructiOn GuiDe FOr PrOPer DiMensiOns
OF tHe OPeninG FOr tHe Bsa-1 siDe Burner surrOunD
THE BSA SIDE BURNER SURROUND IS DESIGNED TO BE USED WITH THE DPASBC NATURAL and PROPANE GAS SIDE BURNER ONLY. DO NOT USE ANY OTHER SIDE BURNER WITH THE BSA SIDE BURNER SURROUND.
Page 15B101502-3-1012
Bsa siDe Burner surrOunD eXPlODeD view anD Parts list
1
2
3
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact Broilmaster® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model number of your Side Burner, Part Name, Part Number, and Quantity of parts needed.
PARTS LIST
Index No. Part No. Description Quantity
1 B101164 Side Burner Liner 1 2 B100130 10-24 x 3/8 Phillips Head Screw
(for use only with DPASBC Side Burner)
3 B101022
8 x 3/4” Hex Head Screw
2
4
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN
THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION.
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.
Page 16 B101502-3-1012
Bsa installatiOn
Recommended Tools: Phillips Screw Driver or an electric screw driver.
1
Make sure BSA Side Burner Surround opening dimensions match those in FIGURE 1. Place the BSA Liner into the Enclosure and check for proper hole alignment. Secure the BSA Liner to the Enclosure with four (4) 8 x 3/4” Hex Head screws. You should use the
inside holes located on the inside of the BSA Liner.
FIGURE 2.
2
Attach one end of the Side Burner Hose to your
Broilmaster® DPASBC Side Burner. The remaining end of the hose should be routed down through the bottom of the BSA Liner. Place the side burner into the BSA Liner and slide it completely to the rear of the Liner. FIGURE 3.
ENCLOSURE
14 3/8”
(4)SCREWS
12 3/16”
FIGURE 1
BSA LINER
IGURE 3
F
3
Secure the DPASBC Side Burner to the BSA Liner
with two 10-24 x 3/8 PH PN screws to the inside holes located on the side of the Side Burner. FIGURE 4. Note: If you have already routed your Side Burner Hose make sure it is projecting up through the bottom
of the BSA Liner.
#10-24x3/8 PH PN SCREWS (2)
FIGURE 2
IGURE 4
F
Page 17B101502-3-1012
BDa-1 sinGle/DOuBle DOOr Kit
INSTALLATION INSTRUCTIONS
nOtice: reFer tO tHe Built-in Kit enclOsure cOnstructiOn GuiDe FOr PrOPer DiMensiOns
OF tHe OPeninG FOr tHe BDa-1 sinGle/DOuBle DOOr Kit
THE BDA SINGLE DOOR KIT IS DESIGNED TO BE USED IN AN ISLAND OR OTHER APPLICATION.
Page 18 B101502-3-1012
BDa sinGle DOOr eXPlODeD view anD Parts list
1
3
4
2
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact Broilmaster® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model number of your Single Door, Part Name, Part Number, and Quantity of parts needed.
PARTS LIST
Index No. Part No. Description Quantity
1 B101191 BDA Door Frame 1
2 B101022 8 x 3/4” Hex Head Screw 8
3 B101192 BDA Door 1
4 B101153 BDA Door Bracket (used on double door installation
only)
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN
THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION.
1
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.
Page 19B101502-3-1012
BDa sinGle DOOr installatiOn
Attention: If Applicable, remove protective lm from parts before installation.
Recommended Tools: Phillips Screw Driver or an electric screw driver.
1
The BDA Single Door will be fully assembled when it is shipped out. Remove door from frame by depressing one of the spring loaded pins and set aside. FIGURE 1.
SCREW (8)
FIGURE 3
FIGURE 1
2
Make sure BDA Single Door opening dimensions match those in FIGURE 2. Place the Frame into the opening and check for proper hole alignment. Secure the Frame to the grill enclosure with eight (8)
Hex Head Screw screws. FIGURE 3.
14”
19 13/16”
8 x 3/4”
3
Secure the BDA Door to the door frame by inserting the spring loaded pin in the bottom frame hole. Locate the upper hole in the frame then push on the spring loaded pin on the door and insert the door in the frame.
Figure 4.
Make sure the Door is Aligned and Secured prop­erly by opening and closing door
FIGURE 2
Page 20 B101502-3-1012
FIGURE 4
BDA DOUBLE DOOR INSTALLATION
NOTE: You will need two BDA door kits for this installation.
3
1
Remove doors from frames by depressing one of the spring loaded pins on each door and set them aside. Disassemble frame by removing the two screws and door pin from both door frames as shown in FIGURE
5.
FIGURE 5
Make sure BDA Double Door opening dimensions match those in FIGURE 7. Place the Frame into the opening and check for proper hole alignment. Secure the Frame to the enclosure with 2 screws. FIGURE 7.
Secure the Doors to the door frame by inserting the spring loaded pins in the bottom frame holes. Locate the upper hole in the BDA frame and push on the spring loaded pin on the door and insert it into the frame.
Figure 4.
Make sure the Door is Aligned and Secured prop­erly by opening and closing door.
27 ½”
19 13/16”
2
Use the door brackets included in the hardware packages to combine the frames. Use the screws from the single door to attach the bracket, and place the door pin in position. FIGURE 6
FIGURE 7
FIGURE 6
Page 21B101502-3-1012
BRB-1 VENT REGISTER KIT
INSTALLATION INSTRUCTIONS
nOtice: reFer tO tHe Built-in Kit enclOsure cOnstructiOn GuiDe FOr PrOPer DiMensiOns
OF tHe OPeninG FOr tHe BrB-1 vent reGister Kit
The BRB Vent Register Kit is designed to be used with any enclosure that has an LP tank.
Page 22 B101502-3-1012
BrB vent reGister cOver Kit eXPlODeD view anD Parts list
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact Broilmaster service, please provide the following information when placing a repair part order: Model number of your Side Burner, Part Name, Part Number, and Quantity of parts needed.
®
Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate
1
2
PARTS LIST
Index
No.
1 B071712 Vent Register 2
2 B101022 8 x 3/4” Hex Head Screw 4
Two BRB Vent Register kits are needed for proper installation.
Part No. Description Quantity
Install two vent registers into each side of the Built-In Kit Enclosure using two screws per vent register.
Page 23B101502-3-1012
LIMITED WARRANTY
Manufactured in U.S.A. by Broilmaster, a Division of Empire Comfort Systems, Inc., P.O. Box 529, Belleville, Illinois 62222.
WHAT IS COVERED AND FOR HOW LONG
From the date these kits are purchased for use, Broilmaster will make available, at our factory, a free replacement for any defective part covered by this warranty on the fol­lowing basis:
LIMITED LIFETIME WARRANTY
Stainless Components for Built-In Series (BHA, BBA, BSA, BDA, & BRB)
Page 24 B101502-3-1012
nOtes
Page 25B101502-3-1012
nOtes
Page 26 B101502-3-1012
nOtes
Page 27B101502-3-1012
THE MOST DURABLE GRILL
KNOWN TO MAN
BROILMASTER®
A Division of Empire Comfort Systems, Inc.
918 Freeburg Ave.
Belleville, Illinois 62220
Phone: 1-800-851-3153
FAX: 1-800-443-8648
VISIT OUR WEB SITE AT WWW.broilmaster.com
Page 28 B101502-3-1012
Loading...