Broan 103023 User Manual
MODEL 103023
!
!
WOOD HOOD KIT
READ AND SAVE THESE INSTRUCTIONS
FOR DOMESTIC COOKING ONLY
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only metal ductwork.
9. Use with approved cord-connection kit only.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite.
2. Always turn hood ON when cooking at high heat or when cooking flaming
foods.
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam
explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already know how
to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
3. For best capture of cooking impurities, your range hood should be
mounted so that the bottom of the hood is 18-24” above the cooking
surface.
4. Please read specification label on product for further information and
requirements.
Use 3¼" x
10" duct and
a 900 elbow
to exhaust
horizontally.
This wood hood kit can be easily installed by following three basic
steps:
Install a wood mounting frame in hood
•
Install the hood kit
•
Mount the hood in place on the wall
•
This wood hood kit requires the previous installation of Broan
Model 103123 Rough-in Kit including:
120 VAC electrical wiring
16”
16” MIN.
19¼” MAX.
•
3¼” x 10” metal ductwork (extending down to 16” above bottom
•
of wood hood)
INSTALLER: Leave this manual with the homeowner.
HOMEOWNER: Use and care information on page 5.
INSTALL MOUNTING FRAME
LENGTH OF
FRONT & REAR BOARDS
TO BE INSIDE WIDTH
OF WOOD HOOD
LENGTH OF (2)
SIDE FRAMING
PIECES
(Mounting Brackets must
fit inside frame)
L
C
TO CENTER LINE
OF SLOTS
IN BRACKETS
MOUNT BLOWER HOUSING
#10 x 7/8
BACK OF
WOOD HOOD
SHEET METAL
NUT
BRACKETS TO
BE FLUSH WITH
WOOD FRAMING
(continued)
PUSH HOUSING IN
THIS DIRECTION
1/4-20 x 1/2
DUCT
OPENING
FRONT OF
WOOD HOOD
4. Fasten housing to mounting brackets with four (4) screws. Push
housing toward top of wood hood, as far as mounting slots will
allow. Make sure duct opening is toward back of hood.
1. Construct a wood frame which will fit the hood and allow the
ductwork to line up with damper assembly. Attach the mounting brackets with the sheet metal nuts toward the hood front.
Secure frame to hood using dimensions shown.
MOUNT BLOWER HOUSING
DAMPER ASSEMBLY
SHEET METAL SCREW
BLOWER HOUSING
WHEEL
BLOWER ASSEMBLY
MOUNTING ROD
INSTALL LINER
(for 30” Wood Hood)
CLEARANCE
HOLE
SHEET
METAL
NUT
INSIDE
DIMENSION
28-1/4” to 28-7/8”
#8 x 3/8
CLEARANCE
HOLE
KNURLED NUT
2. Remove the blower assembly by unplugging it, loosening the
knurled nuts and pivoting mounting rods away from blower.
3. Remove the damper assembly by unscrewing the two (2) sheet
metal screws and sliding it back through the housing.
FRONT OF
WOOD HOOD
5. Make sure two (2) clearance holes in liner are lined up with
sheet metal nuts on mounting brackets. Then screw liner pieces
2
to mounting frame in nine (9) places.
INSTALL LINER (continued)
#8 x ½
6. Fasten the two, adjustable front liners to hood with eight (8)
screws provided. Use a 7/ 64” dia. drill bit to drill through liners
and fasten them securely where they overlap.
MOUNT HOOD (continued)
NOTE:
Lamp Receptacles are
toward
REAR of hood.
10. Plug in control unit and fasten to hood as shown.
MOUNT HOOD
POWER
CORD
DUCT
OPENING
7. Secure hood to wall, soffit or cabinets as appropriate.
8. Reach up through duct opening and connect power cord to
blower housing.
9. Slide damper assembly up into ductwork and refasten to blower
housing (using the two (2) screws removed in Step 3). Reinstall
blower assembly and plug it in.
NOTE:
Filter Tabs
are toward
REAR of hood.
11. Install aluminum filter. Rotate two (2) retaining clips (on the
hood liner) to hold filter in place.
12. Install an F20T12 fluorescent tube (not supplied).
3
Loading...