Breville BKC700XL, XXBKC600XL User Manual

Gourmet Single Cup Brewer™

Instruction Booklet Livret d’instructions

BKC600XL / BKC700XL

2

CONGRATULATIONS

On the purchase of your new Breville Gourmet Single Cup Brewer™

CONTENTS

4 Breville recommends safety ﬁrst 6 Know your Breville Gourmet Single Cup

Brewer™

8 Operating your Breville Gourmet Single

Cup Brewer™

9 - Installing the water ﬁlter 10 - One-time priming process 12 - Brewing a K-Cup

®

14 - Brewing with the My K-Cup

®

18 - Stopping the brew process 18 - Brewing hot water 18 - Reﬁlling the water tank 19 - Purging the brewer 20 Menu and programming options 21 - Setting the ‘CLOCK SET’ feature 22 - Setting the ‘ON-OFF TIME’ feature 23 - Setting the ‘AUTO OFF’ feature 24 - Setting the ‘BREW TEMP’ feature 24 - Setting the ‘BREW SIZE’ feature 26 Care and cleaning 27 - Cleaning the brewer housing 27 - Cleaning the K-Cup

®

holder

28 - Cleaning the My K-Cup

®

28 - Cleaning the water tank and lid 28 - Cleaning the water ﬁlter 28 - Descaling the brewer 30 - Storage 32 Trouble shooting 34 One year limited warranty 36 French

4

5

BREVILLE RECOMMENDS SAFETY FIRST BREVILLE RECOMMENDS SAFETY FIRST

We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions:

READ ALL INSTRUCTIONS BEFORE USE & SAVE FOR FUTURE REFERENCE

This appliance is for household use only.•

Do not use this appliance for anything • other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.

To protect against ﬁre, electrical shock • and injury to persons, do not immerse the appliance, cord or plug in water or any other liquid.

Do not leave the appliance unattended • when in use.

Close supervision is necessary when the • appliance is used by or near children.

Always use the appliance on a dry, level • surface.

Do not place this appliance on or near • a hot gas or electric burner, or where it could touch a heated oven.

Do not touch hot surfaces. Use handles • and knobs where available.

Do not let the cord hang over the edge of • a table or counter, touch hot surfaces or become knotted.

The use of accessory attachments not • recommended by Breville may cause a risk of injury to persons, ﬁre or electric shock.

Do not overﬁll the Water Tank. •

Always keep the Water Tank Lid on the • Water Tank unless you are reﬁlling it.

Use only water in this appliance. Do • not put any other liquids or foods in the Water Tank except as instructed in Care and Cleaning (page 26).

There are two sharp needles that • puncture the K-Cup

®

. One on the underside of the Brewing Chamber Head, and the other in the base of the K-Cup® Holder. To avoid risk of injury, do not put your ﬁngers in the Brewing Chamber or K-Cup® Holder.

There is extremely hot water in the • K-Cup

®

Holder during the brewing process. To avoid risk of injury, do not raise the Safety Locking Arm or open the Brewing Chamber during the brewing process.

To turn off the appliance, press and • release the Power Switch on the lower back, right side of the Brewer to the ‘OFF’ status and then remove the plug from the wall outlet.

Always switch the appliance to the • ‘OFF’ status and then remove the plug from the wall outlet when the appliance is not being used and before cleaning. Allow the appliance to cool before reassembling or removing parts and before cleaning the appliance.

Strictly follow the Care and Cleaning • instructions (page 26).

This appliance is equipped with a power • cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.

IMPORTANT SAFEGUARDS

If the outlet is a standard 2-prong wall • outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

Do not, under any circumstances, cut or • remove the third (ground) prong from the power cord or use an adapter.

Consult a qualiﬁed electrician if the • grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

Regularly inspect the supply cord, plug • and actual appliance for any damage. Do not operate if damaged in anyway or after the appliance malfunctions. Immediately cease use of the appliance and call Breville Customer Service at 1-866-BREVILLE for examination, repair or adjustment.

For any maintenance other than cleaning, • call Breville Customer Service at 1-866-BREVILLE.

NOTE: Your Breville appliance comes with the unique Assist™ Plug, conveniently designed with a ﬁnger hole in the power plug for easy and safe removal from the wall outlet. For safety reasons it is recommended you plug your Breville appliance directly into its own electrical outlet on a dedicated circuit separate from other appliances. If the electric circuit is overloaded with other appliances, your Brewer may not function properly. Use in conjunction with a power strip or extension cord is not recommended.

SHORT CORD INSTRUCTIONS

Your Breville appliance is ﬁtted with a short power supply cord as a safety precaution to prevent personal injury or property damage resulting from pulling, tripping or becoming entangled with a longer cord. Do not allow children to use or be near this appliance without close adult supervision. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT REMOVE THE BASE PANEL. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE ONLY BY AUTHORIZED PERSONNEL ONLY.

!

6

7

KNOW YOUR BREVILLE GOURMET SINGLE CUP BREWER™ BREVILLE RECOMMENDS SAFETY FIRST

A Water tank lid B 60oz (1.8L) Water tank C Upper ﬁlter holder D Replaceable charcoal ﬁlter E Lower ﬁlter holder

F Drip tray plate G Drip tray level indicator H Drip tray I K-Cup

®

holder

J Safety locking arm

K Brewing chamber head L Brewing chamber M LCD screen N Control panel O My K-Cup

®

/ K-Cup®

holder storage

P My K-Cup

®

measuring scoop

Q My K-Cup

®

lid

R My K-Cup

®

ﬁlter basket

S My K-Cup

®

holder

T Power Switch

NOTE: To order replacement Charcoal Filters, call Breville Customer Service at 1-866-BREVILLE or visit www.breville.com

8

9

OPERATING

your new Breville Gourmet Single Cup Brewer™

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

INSTALLING THE WATER FILTER

For the best tasting gourmet coffee, tea or hot cocoa, Breville recommends using bottled or ﬁltered water.

The Water Filter provided with the Brewer can signiﬁcantly reduce substances that affect the smell and taste of water such as free chlorine, certain pesticides and organic impurities as well as traces of heavy metals.

NOTE: The Water Filter can be removed from the Brewer.

If you choose to install the Water Filter, it is recommended to replace the Charcoal Filter every 2 months or 60 tank reﬁlls, more often if you have hard water.

We recommend removing the Water Filter if using ﬁltered water, or if you choose not to replace the Charcoal Filter every 2 months, as the ﬁlter may clog and affect the smell and taste of the water.

If you choose not to install the Water Filter, you are ready to start the One-time Priming Process (page 10).

NOTE: Do not use water that has been treated by a 'water softener'. The increase in sodium levels in the water can cause scaling in the brewer and hinder its performance.

Follow these steps each time you install a new Charcoal Filter to ensure it ﬁlters optimally.

Remove the Water Tank from the Brewer 1. by gripping the handle located on the left side of the Water Tank, then lift upwards.

Remove the Water Tank Lid.2.

Rinse the Water Tank with fresh water 3. and replace back onto the Brewer.

Remove the Upper and Lower Filter 4. Holder and Charcoal Filter from the polybag. Unwrap the Charcoal Filter from its protective plastic.

Soak the Charcoal Filter for 5 minutes 5. then rinse for 30 seconds. It is normal to see a grey residue after soaking the ﬁlter.

Wash the Lower Filter Holder, ensuring 6. the stainless steel mesh is free of residue.

Insert the Charcoal Filter into the Upper 7. Filter Holder, then attach the Lower Filter Holder so it locks into place.

10

11

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

ONE-TIME PRIMING PROCESS

Priming ﬁlls the internal tank with water and cleanses the brewing system. You cannot use your Brewer until it has been primed for its ﬁrst use.

NOTE: If the Brewer has been exposed to temperatures below freezing, allow the Brewer at least two hours to reach room temperature before priming. A frozen or extremely cold Brewer will not prime properly and can cause damage.

Unwrap the power cord and plug the 1. Brewer into a grounded outlet.

Place a 12 oz. mug on the Drip Tray 2. Plate. The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs.

Fill the Water Tank with water up to the 3. 'MAX' mark on the viewing window.

The Water Tank can be ﬁlled in two ways:

a) Remove the Water Tank Lid and pour

water directly into the Water Tank while it is still attached to the Brewer, then replace the Lid.

b) Remove the Water Tank Lid, then

gripping the handle located on the left side of the Water Tank, lift upwards. Fill with water. Place the Water Tank back onto the Brewer and replace the Lid.

NOTE: Do not use water that has been treated by a 'water softener'. The increase in sodium levels in the water can cause scaling in the brewer and hinder its performance.

Press and release the Power Switch 4. located on the lower back, right side of the Brewer. The Power Switch is spring loaded and will return to its original position.

NOTE: For BKC600XL priming information, please refer to page 30.

The Water Tank LED and LCD screen will 5. illuminate. The Brewer will automatically ﬁll with water and make a quiet vibrating sound. This is normal. The LCD screen will indicate 'HEATING'.

Set the date dial on the Upper Filter 8. Holder 2 months ahead. This will remind you when the Charcoal Filter will need to be replaced.

Place the assembled Filter Holder into 9. the Water Tank, aligning so the date dial is visible from outside the Tank. Push down hard on the assembled Filter Holder until it snaps into place.

Your Brewer is ready for the one-time 10. priming process.

NOTE: Replace the Charcoal Filter every 2 months, or 60 tank reﬁlls, more if you have hard water.

To order replacement Charcoal Filters, call Breville Customer Service at 1-866-BREVILLE or visit www.breville.com.

We recommend removing the Water Filter if you choose not to replace the Charcoal Filter every 2 months, as the ﬁlter may clog and affect the smell and taste of the water.

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

NOTE: If the Water Tank is empty or not in place on the Brewer, the Water Tank LED’s will ﬂash and the LCD screen will indicate ‘REFILL TANK’. None of the control panel buttons will be active until water is added to the Water Tank.

Once the water is heated, the LCD 6. screen will indicate 'OPEN HEAD'. Open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely. Do not insert a K-Cup

®

during this process. This will allow you to run a cleansing brew. The 'BREW' button will now be illuminated.

Press the 'BREW' button. This will start 7. a cleansing brew which will complete the priming sequence. Hot water will ﬂow into your mug. When the water ﬂow stops, discard the hot water.

NOTE: The Brewer will take about 4 minutes to heat up during the priming process.

The LCD screen will indicate ‘HEATING’ 8. as the Brewer heats the water for the next brew cycle. Once the water is heated, the LCD screen may indicate ‘REFILL TANK’.

Fill the Water Tank with water up to the 9. 'MAX' mark on the viewing window.

The LCD screen will indicate ‘OPEN 10. HEAD’. Open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely. The LCD screen will indicate ‘READY TO BREW’.

The one-time priming process is now 11. complete and you are ready for your ﬁrst K-Cup

®

brew (page 12) or My

K-Cup® brew (page 14).

12

13

NOTE: There are two sharp needles that puncture the K-Cup®. One on the underside of the Brewing Chamber Head and the other in the base of the K-Cup® Holder. To avoid risk of injury, do not put your ﬁngers in the Brewing Chamber or K-Cup® Holder.

Lower the Safety Locking Arm to 7. close the Brewing Chamber Head over the K-Cup

®

Holder. When closed completely, the LCD screen will indicate ‘READY TO BREW’. The and buttons will illuminate and the ‘BREW’ button will illuminate and ﬂash for up to 60 seconds.

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

BREWING A K-CUP

®

Follow the instructions, Installing the 1. Water Filter (page 9) and the One-time Priming Process (page 10). The Brewer should be turned on and the Water Tank should be ﬁlled and illuminated.

The LCD screen will indicate ‘READY 2. TO BREW’. The and buttons will illuminate and the ‘BREW’ button will illuminate and ﬂash for up to 60 seconds.

NOTE: If the ‘BREW’ button is not pressed in 60 seconds, the LCD screen will indicate ‘OPEN HEAD’ and the ‘BREW’ button will be disabled to prevent accidental activation. To re-activate the brew sequence, open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely.

Place a cup or mug on the Drip Tray 3. Plate. The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs.

Raise the Safety Locking Arm. The 4. Brewing Chamber will open toward you.

Select a K-Cup5.

®

.

Place the K-Cup6.

®

in the K-Cup® Holder (located in the Brewing Chamber). Do not remove the foil lid or puncture the K-Cup®.

NOTE: If the ‘BREW’ button is not pressed in 60 seconds, the LCD screen will indicate ‘OPEN HEAD’ and the ‘BREW’ button will be disabled to prevent accidental activation. To re-activate the brew sequence, open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely.

The LCD screen will indicate 8. ‘BREWING’, however there may be a short pause before the brewing process begins. The process lasts about 60 seconds and ends with a burst of air to remove all liquid from the K-Cup

®

.

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

a) The LCD screen will indicate the

default brew size (7.25 oz.). To choose a different size, press the button to go up in size or the button to go down in size.

NOTE: Select from a stronger small cup (5.25 oz. serving), a small mug (7.25 oz. serving), a large mug (9.25 oz. serving), a travel mug (11.25 oz. serving) or iced beverage setting (3.25oz serving). The iced beverage setting is only available on the the BKC700XL.

The small mug (7.25 oz. serving) is the default brew size.

To program your favorite brew size, refer to Setting the ‘BREW SIZE’ feature (page 24).

NOTE: To use the iced beverage setting, place a tall glass ﬁlled with ice on the drip tray. Use your favorite K-Cup

®

, select the iced beverage brew size button. Add more ice once brewing is complete, add cream and sugar if desired. The iced beverage setting is only available on the BKC700XL.

b) Once the brew size is selected, press

the ‘BREW’ Button. The ‘BREW’ button will stop ﬂashing, the and buttons will no longer be lit. The LCD screen will indicate ‘BREWING’ and the selected brew size.

14

15

BREWING WITH THE MY K-CUP® ACCESSORY

The Breville Gourmet Single Cup Brewer™ comes with a My K-Cup® accessory. The dishwasher safe, reusable My K-Cup® allows you to use your own grind of coffee so you can adjust the amount and type of coffee to suit your tastes. Along with the included measuring scoop, this accessory conveniently stores in the easy open compartment on top of the brewer.

Follow the instructions, Installing the 1. Water Filter (page 9) and the One-time Priming Process (page 10). The Brewer should be turned on and the Water Tank should be ﬁlled and illuminated.

NOTE: Do not use water that has been treated by a 'water softener'. The increase in sodium levels in the water can cause scaling in the brewer and hinder its performance.

The LCD screen will indicate ‘READY 2. TO BREW’.

NOTE: If the ‘BREW’ button is not pressed in 60 seconds, the LCD screen will indicate ‘OPEN HEAD’ and the ‘BREW’ button will be disabled to prevent accidental activation. To re-activate the brew sequence, open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely.

Place a cup or mug on the Drip Tray 3. Plate. The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs.

NOTE: There is extremely hot water in the K-Cup

®

Holder during the brewing process. To avoid risk of injury, do not raise the Safety Locking Arm or open the Brewing Chamber during the brewing process.

Following the brew, the LCD screen will indicate ‘HEATING’ as the Brewer heats the water for the next brew cycle. This process lasts about 15 seconds. The pump will make a vibrating sound. This is normal.

Raise the Safety Locking Arm, remove 9. and dispose of the used K-Cup

®

. Use

caution as the K-Cup

®

will be hot.

Enjoy your ﬁrst cup of gourmet coffee, 10. tea or hot cocoa!

The LCD screen will indicate ‘READY 11. TO BREW’, indicating that the next K-Cup

®

can be inserted for the next

brew cycle.

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™ OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

Open the storage compartment located 4. on top of the Brewer by pressing the ﬁnger indent on the right side. Remove the My K-Cup® accessory.

Disassemble the My K-Cup5.

®

accessory by removing the Lid from the Holder in a counterclockwise direction. Remove the Filter Basket from the Holder.

Wash the My K-Cup6.

®

Lid, Filter Basket and Holder in warm soapy water prior to ﬁrst use. Rinse and dry thoroughly.

Insert the Filter Basket into the Holder.7.

Use the My K-Cup8.

®

Measuring Scoop to ﬁll the Filter Basket with 1 level scoop maximum of coffee. 1 level scoop is equivalent to 2 tablespoons. Alternatively, there are line markings on the inside of the Filter Basket that indicate 1 tablespoon and 2 tablespoons so you can adjust the amount of coffee to your personal preference. Do not ﬁll the Filter Basket with more than one level scoop of coffee or tamp the grinds. Ensure the coffee remains loose and there are no coffee grinds remaining on the upper rim of the Filter Basket. Screw on the Lid to seal.

NOTE: 1 level scoop = 2 tablespoons

We recommend this for the small mug 7.25 oz. serving.

Or, if you like a stronger brew, select the small cup 5.25 oz. serving.

If you grind your own beans:

1. Start with a coarser grind similar to a French Press grind.

2. Experiment with grinds similar to drip brewing grinds.

3. Avoid a ﬁne espresso grind setting that could clog the Filter Basket or result in poor extraction.

Raise the Safety Locking Arm. The 9. Brewing chamber will open toward you.

Place the assembled My K-Cup10.

®

Holder into the Brewing Chamber. To do this:

a) Remove the K-Cup

®

Holder from the Brewing Chamber (10a). Store the K-Cup® Holder in the My K-Cup® Storage compartment located on top of the Brewer.

b) Insert the assembled My K-Cup

®

Holder into the Brewing Chamber (10b), ensuring to align the arrow on the My K-Cup® Lid with the arrow in the Brewing Chamber.

16

17

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

NOTE: There are two sharp needles used to puncture the K-Cup® and My K-Cup® Holder. One in the base of the K-Cup® Holder, the other on the underside of the Brewing Chamber Head. To avoid risk of injury, use caution when inserting or removing the K-Cup®, K-Cup® Holder or My K-Cup® Holder.

Lower the Safety Locking Arm to close 11. the Brewing Chamber Head over the My K-Cup

®

Holder. When closed completely, the LCD screen will indicate ‘READY TO BREW’. The and buttons will illuminate and the ‘BREW’ button will illuminate and ﬂash for up to 60 seconds.

a) The LCD screen will indicate the

default brew size (7.25 oz.). To choose a different size, press the to go up in size or the button to go down in size.

NOTE: Select from a stronger small cup (5.25 oz. serving), a small mug (7.25 oz. serving), a large mug (9.25 oz. serving), a travel mug (11.25 oz. serving) or iced beverage setting (3.25oz serving). The iced beverage setting is only available on the the BKC700XL.

The small mug (7.25 oz. serving) is the default brew size.

To program your favorite brew size, refer to Setting the ‘BREW SIZE’ feature (page 24).

NOTE: To use the iced beverage setting, place a tall glass ﬁlled with ice on the drip tray. Use your favorite K-Cup

®

, select the iced beverage brew size button. Add more ice once brewing is complete, add cream and sugar if desired. The iced beverage setting is only available on the BKC700XL.

b) Once the brew size is selected,

press the ‘BREW’ Button. The ‘BREW’ button will stop ﬂashing, the and buttons will no longer be lit. The LCD screen will indicate ‘BREWING’ and the selected brew size.

NOTE: There is extremely hot water in the My K-Cup® Holder during the brewing process. To avoid risk of injury, do not raise the Safety Locking Arm or open the Brewing Chamber during the brewing process.

Following the brew, the LCD screen will indicate ‘HEATING’ as the Brewer heats the water for the next brew cycle. This process lasts about 15 seconds. The pump will make a vibrating sound. This is normal.

Raise the Safety Locking Arm, remove 13. the assembled My K-Cup

®

Holder. Use

caution as the My K-Cup

®

Holder will

be hot.

Disassemble the My K-Cup14.

®

Holder by removing the Lid from the Holder in a counter-clockwise direction. Remove the Filter Basket from the Holder, discard the grounds and rinse out the Filter Basket and Holder.

15. Enjoy your ﬁrst cup of gourmet 15. coffee, tea or hot cocoa!

NOTE: If the ‘BREW’ button is not pressed in 60 seconds, the LCD screen will indicate ‘OPEN HEAD’ and the ‘BREW’ button will be disabled to prevent accidental activation. To re-activate the brew sequence, open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely.

The LCD screen will indicate 12. ‘BREWING’, however there may be a short pause before the brewing process begins. The process lasts about 60 seconds and ends with a burst of air to remove all liquid from the My K-Cup

®

Holder.

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

18

19

The LCD screen will indicate either:2. a) ‘OPEN HEAD’. Raise and lower the

Safety Locking Arm completely.

b) ‘HEATING’ as the Brewer heats the

water for the next brew cycle. This process lasts about 15 seconds. The pump will make a vibrating sound. This is normal.

Once the Safety Locking Arm is opened 3. and lowered, or the water is heated, the LCD screen will indicate ‘READY TO BREW’, indicating the brew cycle can begin. The and buttons will illuminate and the ‘BREW’ button will illuminate and ﬂash for up to 60 seconds.

NOTE: If the ‘BREW’ button is not pressed in 60 seconds, the LCD screen will indicate ‘OPEN HEAD’ and the ‘BREW’ button will be disabled to prevent accidental activation. To re-activate the brew sequence, open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely.

Do not remove the Water Tank during the brewing process.

PURGING THE BREWER

If the Brewer has not been used for more than one week, you should renew the water from the inner tank by purging the brewer.

If there is water in the Water Tank, 1. remove the Water Tank Lid, then gripping the handle located on the left side of the Water Tank, lift upwards. Discard the water, rinse and reﬁll with bottled or ﬁltered water. Place the Water Tank back onto the Brewer and replace the Lid.

NOTE: You may get less coffee, tea or hot cocoa during your next brew. After a terminated brew, we recommend that you follow the instructions for Brewing hot water (page 18). Your next brew will then dispense the correct volume according to the brew size you have selected.

BREWING HOT WATER

The Brewer is able to dispense a cup of hot water for making hot chocolate in a packet, for use in cooking, for making soups, etc. Follow the instructions Brewing a K-Cup® (page 12), without inserting a K-Cup®.

NOTE: After brewing a hot cocoa K-Cup

®

, or stopping the brew process mid-cycle, we recommend running a hot water brew cycle.

SROPPING THE BREW PROCESS

To stop brewing after the process has started, press and release the Power Switch on the right side of the Brewer to the ‘OFF’ status. The ﬂow of coffee, tea or hot cocoa will stop, the heating element will shut off and the LED’s illuminating the Water Tank will no longer be lit. The LCD screen will indicate the time, ‘ON-OFF TIME’ and ‘AUTO OFF’. None of the control panel buttons will be active until the Brewer is turned back on.

OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™OPERATING YOUR BREVILLE GOURMET SINGLE CUP BREWER™

REFILLING THE WATER TANK

The LCD screen will indicate ‘REFILL TANK’ when the water level in the Water Tank is low or if the Water Tank has been removed.

Fill the Water Tank with water up to the 1. 'MAX' mark on the viewing window. The Water Tank can be ﬁlled in two ways:

a) Remove the Water Tank Lid and pour

water directly into the Water Tank while it is still attached to the Brewer, then replace the Lid.

b) Remove the Water Tank Lid, then

gripping the handle located on the left side of the Water Tank, lift upwards. Fill with water. Place the Water Tank back onto the Brewer and replace the Lid.

If there is no water in the Water Tank, reﬁll 2. with water. Place the Water Tank back onto the Brewer and replace the Lid.

Ensure the Brewer is turned on. Raise 3. and lower the Safety Locking Arm on the Brewer without inserting a K-Cup

®

.

The LCD screen will indicate ‘READY 4. TO BREW’ and the ‘BREW’ button will illuminate and ﬂash.

The LCD screen will indicate the default 5. brew size (7.25 oz. serving unless programmed otherwise). Select the largest brew size (11.25 oz. serving) by pressing the button on the control panel.

Place a 12 oz. mug on the Drip Tray 6. Plate. The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs.

Press the ‘BREW’ button. Hot water will 7. ﬂow into your mug. When the ﬂow stops, discard the hot water.

Repeat this process 2 more times to 8. completely renew the water from inner tank.

NOTE: The My K-Cup® accessory is designed for ground coffee only. Do not:

a) Use a K-Cup

®

or coffee pod in

the My K-Cup® Filter Basket.

b) Use the My K-Cup

®

Filter Basket with the K-Cup® Holder After brewing with the My K-Cup® accessory, the K-Cup® Holder must be inserted into the Brewing Chamber in order to brew a K-Cup®.

To replace the K-Cup

®

Holder, raise the Safety Locking Arm, and remove the My K-Cup® Holder. Insert K-Cup® Holder into the Brewing Chamber, aligning the arrow on the K-Cup® Holder with the arrow in the Brewing Chamber. Use caution when doing this as there is a sharp needle on the underside of the Brewing Chamber Head that punctures the K-Cup®.

20

21

SETTING THE ‘CLOCK SET’ FEATURE

Setting the clock is optional. When the clock is set, the time will appear on the LCD screen.

NOTE: You must set the clock if using the ‘ON-OFF TIME’ feature.

Press the ‘MENU’ button. The menu 1. programming options will appear on the LCD screen with a blinking indicator on ‘CLOCK SET’.

Press the ‘OK’ button. The hour will 2. blink, indicating the hour is ready to be set.

Press the or button to reach the 3. appropriate hour. If the hour has passed 12, the indicator switches from AM to PM.

Once the appropriate hour is reached, 4. press the ‘OK’ button. The minutes will blink, indicating that the minutes are ready to be set.

MENU & PROGRAMMING

your new Breville Gourmet Single Cup Brewer™

Press the or button to reach the 5. appropriate minute.

Once the appropriate minute is reached, 6. press the ‘OK’ button. The LCD screen will return to the menu programming options.

To exit the menu programming options, 7. press the ‘MENU’ button. Alternatively, press the button to reach ‘EXIT MENU’ and press the ‘OK’ button. The LCD screen will return to the main screen and indicate the time selected.

NOTE: If power is interrupted to the Brewer, the clock will need to be reset. Programmed brew size and brew temperature settings are remembered and restored automatically. All other settings will be restored automatically after the clock is reset.

MENU & PROGRAMMING OPTIONS

22

23

SETTING THE ‘ON-OFF TIME’ FEATURE

This feature allows you to program the speciﬁc time when the Brewer will automatically turn on and/or off. By programming your Brewer to automatically turn on, you will not have to wait for the Brewer to heat the water in the Water Tank. It will take the Brewer approximately 3½ minutes to heat the water from room temperate.

NOTE: You must set the clock if using the ‘ON-OFF TIME’ feature.

An alternative to setting the ‘ON-OFF TIME’ feature is to leave the Brewer on all the time.We recommend this so your Brewer is always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa.

To turn the Brewer off at any time, press and release the Power Switch on the lower back, right side of the Brewer. The clock will remain on if set, however you can not activate the brew cycle. Press and release the Power Switch again to restore power to the Brewer. You will have to wait for the water to heat up before the Brewer is ready to brew.

Press the ‘MENU’ button. The menu 1. programming options will appear on the LCD screen with a blinking indicator on ‘CLOCK SET’.

Press the button to reach ‘ON-OFF 2. TIME’.

Press the ‘OK’ button.3.

MENU & PROGRAMMING OPTIONS

Press the or button to see the 4. two options:

a) ‘ON-OFF TIME’ will be ‘INACTIVE’,

indicating that the Brewer will not turn on or off automatically. Press the ‘OK’ button to select this option. The LCD screen will return to the menu programming options.

b) ‘ON-OFF TIME’ will be ‘ACTIVE’,

indicating the Brewer will automatically turn on and/or off according to the speciﬁc times you set. Press the ‘OK’ button to select this option.

Setting the ‘ON TIME’

i) The LCD screen will display ‘ON TIME’,

indicating that the time you wish the Brewer to automatically turn on is ready to be set. The hour will blink, indicting the hour is ready to be set.

ii) Press the or button to reach

the appropriate hour. If the hour has passed 12, the indicator switches from AM to PM.

iii) Once the appropriate hour is reached,

press the ‘OK’ button. The minutes will blink, indicating that the minutes are ready to be set.

iv) Press the or button to reach the

appropriate minute.

MENU & PROGRAMMING OPTIONS

v) Once the appropriate minute is

reached, press the ‘OK’ button. The LCD screen will display ‘OFF TIME’, indicating that the time you wish the Brewer to automatically turn off is ready to be set.

Setting the ‘OFF TIME’

i) Follow the instructions (ii to iv) for

Setting the ‘ON TIME’.

ii) Once the appropriate time is

reached, press the ‘OK’ button. The LCD screen will return to the menu programming options

To exit the menu programming options, 5. press the ‘MENU’ button. Alternatively, press the button to reach ‘EXIT MENU’ and press the ‘OK’ button. The LCD screen will return to the main screen and indicate whether you have activated the ‘ON-OFF TIME’ feature.

NOTE: If you want to brew outside the ‘ON TIME’ and ‘OFF TIME’ selected, press and release the Power Switch on the lower back, right side of the Brewer to restore power. You will have to wait for the water to heat up before the Brewer is ready to brew.

SETTING THE ‘AUTO OFF’ FEATURE

This feature automatically turns the Brewer off after 2 hours from the last brew.

Press the ‘MENU’ button. The 1. programming options will appear on the LCD screen with a blinking indicator on ‘CLOCK SET’.

Press the button to reach ‘AUTO OFF’.2.

Press the ‘OK’ button.3.

Press the or button to see the 4. two options:

a) ‘AUTO OFF’ will be ‘INACTIVE’ and

the LCD screen will display ‘- - -’, indicating that the Brewer will not turn off automatically. Press the ‘OK’ button to select this option. The LCD screen will return to the menu programming options.

b) ‘AUTO OFF’ will be ‘ACTIVE’ and the

LCD screen will display ‘2 hr’, indicating the Brewer will automatically turn off after 2 hours. Press the ‘OK’ button. The LCD screen will return to the menu programming options.