Breville BJE820XL User Manual 2
the Juice Fountain™ Duo
Instruction Book - Livret d’instructions
BJE820XL
CONGRATULATIONS
on the purchase of your Breville product
Register online for product support
and exclusive offers.
USA Consumers: www.brevilleusa.com
Canadian Consumers: www.breville.ca
*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.
*
CONTENTS
4 Breville recommends safety first
7 Know your Breville product
9 Assembling your Breville product
15 Operating your Breville product
18 Disassembling your
Breville product
23 Care & cleaning
25 Troubleshooting
28 Hints & tips
31 Recipes
44 French
3
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and manufacture consumer products
with the safety of you, our valued customer, foremost in mind. In addition we ask that you
exercise a degree of care when using any electrical appliance and adhere to the following
precautions.
IMPORTANT SAFEGUARDS
CAREFULLY READ ALL
INSTRUCTIONS THOROUGHLY
BEFORE OPERATING
When using electrical appliances, basic
safety precautions should always be
followed, including the following:
• To protect against fire, electrical shock
and injury to persons, do not immerse
the appliance, motor base, cord or plug
in water or any other liquid.
• Close supervision is necessary when the
appliance is used by or near children.
• Unplug from outlet when not in use,
before putting on or taking off parts, and
before cleaning or attempting to move
the appliance.
• Avoid contact with moving parts.
• Regularly inspect the supply cord, plug
and actual appliance for any damage.
Do not operate any appliance with
a damaged cord or plug or after the
appliance malfunctions, or is dropped
or damaged in any manner. Contact
Breville consumer support for assistance.
• The use of attachments not
recommended or sold by Breville may
cause fire, electric shock or injury.
• This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors. Misuse may cause injury.
• Do not let the power cord hang over the
edge of a table or counter-top.
• Do not let the power cord touch hot
surfaces, including stove, or become
knotted.
• Always make sure the juicer cover is
clamped securely in place (with safety
locking arm) before the motor is turned
on. Do not unfasten the clamps (safety
locking arm) while the juicer is in
operation.
• Always ensure the juicer is turned off
after each use. Make sure the filter
basket has stopped rotating and the
motor has completely stopped before
disassembling.
• Do not push food into the feed chute
with your fingers or other utensils.
Always use the food pusher provided.
Do not place hand or fingers into the
food chute when it is attached to the
appliance. If food becomes lodged in
feed chute, use food pusher provided
or another piece of fruit or vegetable to
push it down. Turn motor off and ensure
that all moving parts have stopped
before disassembling juicer to remove
the remaining food.
• Do not use appliance if the rotating
sieve (filter basket) is damaged.
• Do not use the appliance without
the pulp container attached to juicer
and juicer cover. Please see assembly
instructions for proper placement.
• Do not modify the plug in any way. If the
unit has a 2-pin plug it is it a polarized
plug. To reduce the risk of electric shock,
this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician.
4
BREVILLE RECOMMENDS SAFETY FIRST
ADDITIONAL SAFEGUARDS
• Remove and safely discard any
packaging material or promotional
labels before using the juicer for the first
time.
• To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug
of this appliance.
• Do not touch the small cutting blades/
teeth in the base of the juicing disc.
• Do not touch the sharp blade in the feed
tube.
• Always make sure the juicer is
properly and completely assembled
before connecting to power outlet and
operating.
• Ensure that the surface where the
appliance operates is stable, level, clean
and dry.
• Vibration can occur during normal
operation.
• Any significant spillage onto the surface
under or around the appliance, or onto
the appliance itself, should be cleaned
and dried before continuing to use the
appliance.
• When using this appliance, provide
adequate air space above and on all
sides for circulation.
• Do not operate juicer for more than a
minute at a time when juicing rapid rate
or with firm pressure. Allow the motor
to rest for 1 (one) minute between each
use.
• This juicer is only designed to juice
fruits and vegetables. Please refer to the
juicing guide to determine the correct
speed for the fruits and vegetables
selected for juicing. Do not use any
frozen fruits or vegetables.
• Hard fruits and vegetables will put
excess strain onto the motor if a low
speed is selected.
• Remove rind from all citrus fruit before
juicing.
• Do not juice stone fruit unless pits or
seed stone have been removed.
• The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
• Do not leave the appliance unattended
when in use.
• Keep hands, fingers, hair, clothing as
well as spatulas and other utensils away
from the appliance during operation.
• Keep the appliance clean. Refer to care
and cleaning section.
• Any maintenance other than cleaning
should be performed by an authorized
Breville Service Center. Do not attempt
to repair or service juicer, Contact
Breville Consumer Support for
assistance.
• When using Puree Disc and insert,
always use the speed 1.
• When using Puree Disc and insert,
always remove seed stone, pits, and rind
from fruit before processing (seeds of
passionfruit, berries and kiwi fruit are
acceptable).
• Do not run ice or hard fruit/vegetables
such as raw beetroot and carrots through
the juicer when using the puree disc.
• If any of the contained instructions or
warnings are not understood please
contact Breville Consumer Support for
assistance.
WARNING
Extra wide feed chute. Do not place
hands or foreign objects down feed
chute. Always use the food pusher
provided.
5
5
BREVILLE RECOMMENDS SAFETY FIRST
SHORT CORD INSTRUCTIONS
Your Breville appliance is fitted with a short
power supply cord to reduce personal injury
or property damage resulting from pulling,
tripping or becoming entangled with a
longer cord. If an extension cord is used, (1)
the marked electrical rating of the cord set
or extension cord should be at least as great
as the electrical rating of the appliance, (2)
the cord should be arranged so that it will
not drape over the countertop or table-top
where it can be pulled on by children or
tripped over unintentionally and (3) the
extension cord must include a 3-prong
grounding plug.
BREVILLE ASSIST™ PLUG
Your Breville appliance comes with a unique
Assist™ Plug, conveniently designed with
a finger hole to ease removal from the wall
outlet. For safety reasons it is recommended
you plug your Breville appliance directly
into its own electrical outlet on a dedicated
circuit separate from other appliances. If
the electric circuit is overloaded with other
appliances, your appliance may not function
properly. It is not recommended to use with
a power strip.
SAVE THESE
INSTRUCTIONS
6
KNOW
your Breville product
PAge heAder.....
KNOW YOUR BREVILLE PRODUCT
G
H
M
A
B
C
D
E
F
A. Juicer cover (dishwasher safe)
B. Large pulp container with integrated
handle
C. High performance 1200 watt motor
D. Five speed electronic control
E. Start|Stop button
F. Cord Storage
G. Food pusher
For pushing whole fruit and vegetables
down the wide feed chute.
(NOT dishwasher safe)
I
J
K
L
H. Extra wide feed chute
I. Safety locking arm
J. Nutri Disc™
Stainless steel titanium reinforced
micro mesh filter basket designed for
optimum juice and nutrient extraction.
(dishwasher safe top shelf)
K. Stainless Steel Filter Bowl Surround
(dishwasher safe)
L. Dishwasher safe 1.2 liter juice jug
M. Puree Disc and Insert
NOTE
All Dishwasher Safe Parts are TOP
SHELF ONLY.
8
NOT SHOWN
Overload protection button
ASSEMBLING
your Breville product
PAge heAder.....
ASSEMBLING YOUR BREVILLE PRODUCT
BEFORE FIRST USE
Before using your juicer for the first time,
remove and safely discard any packaging
material and promotional labels. Ensure the
power cord is unplugged. Wash the Filter
Bowl Surround, Nutri Disc™, Puree Disc,
Puree Insert, Juicer Cover, Food Pusher,
Juice Jug, Juice Jug Lid and Pulp Container
in warm soapy water with a soft cloth or
nylon brush. Rinse and dry thoroughly.
FOR USE WITH THE NUTRI DISC™
Place the motor base on a flat dry surface
such as a counter top. Ensure that the motor
base is turned OFF at the control panel then
unplug the cord.
1. Place the Filter Bowl Surround on the
top of the Motor Base.
2. Align the arrows on the Nutri Disc™ with
the arrows on the Motor Drive Coupling
and push down until it clicks into place.
Ensure the Nutri Disc™ is fitted securely
inside the Filter Bowl Surround and onto
the Motor Base.
3. Place the Juicer Cover over the Filter
Bowl Surround, positioning the Juicer
Cover over the stainless steel filter disc
and lower into position.
4. Raise the safety locking arm up and lock
into the two grooves on either side of
the juicer cover. The safety locking arm
should now be in a vertical position and
locked into place on top of the
juicer cover.
10
PAge heAder.....
ASSEMBLING YOUR BREVILLE PRODUCT
5. Slide the food pusher down the feed
chute by aligning the groove in the food
pusher with the small protrusion on the
inside of the top of the feed chute.
6. Place the Pulp Container into position
by tilting slightly.
NOTE
To minimize cleaning, line the pulp
container with a produce bag to
collect the pulp. Pulp can be used in
other dishes, or as a compost for the
garden or discarded.
NOTE
A glass could also be used to collect
the juice.
NOTE
The Pulp Container can be emptied
during juicing by turning the juicer
OFF and then carefully removing the
Pulp Container. (Replace empty Pulp
Container before continuing to juice).
7. Place the juice jug provided under the
spout on the right hand side of the
juicer. The lid can be placed on to avoid
any splatter.
WARNING
Do not allow the Pulp Container to
overfill as this may prevent correct
operation or damage the unit.
11
PAge heAder.....
ASSEMBLING YOUR BREVILLE PRODUCT
SPEED SELECTOR TABLE SPEED USING
NUTRI DISC™
Apples 5
Apricots (stone removed) 2
Beets (cleaned, trimmed) 5
Blueberries 1
Broccoli 4
Brussels sprouts (trimmed) 5
Cabbage 4
Carrot 5
Cauliflower 4
Celery 5
Cucumber, soft skinned 4
Fennel 5
Grapes (seedless) 1
Kiwi Fruit (peeled) 2
SPEED SELECTOR TABLE SPEED USING
NUTRI DISC™
Plums (stone removed) 2
Raspberries 1
Tomatoes 1
Watermelon (peeled) 1
PREPARATION OF FRUIT
& VEGETABLES FOR JUICE
EXTRACTION
• If using fruits with hard or inedible skins
such as mangoes, guava, melons or
pineapple, always peel before juicing.
• Citrus fruit can be juiced if peeled first.
• All fruits with pits, hard seeds or stones
such as nectarines, peaches, mangoes,
apricots, plums and cherries must be
pitted before juicing.
• A small amount of lemon juice can be
added to apple juice to inhibit browning.
Mangoes (peeled, stone
removed)
Melons (peeled) 1
Nectarines (stone removed) 2
Oranges (peeled) 3
Peaches (stone removed) 2
Pears hard (stalks removed) 5
Pears soft (stalks removed) 2
Pineapple (peeled) 5
12
2
PAge heAder.....
ASSEMBLING YOUR BREVILLE PRODUCT
FOR USE WITH PUREE DISC
Place the motor base on a flat dry surface
such as a counter top. Ensure that the motor
base is turned OFF at the control panel and
the power cord is unplugged.
1. Place the Filter Bowl Surround on the
top of the Motor Base.
2. Place the Puree Disc into the Filter Bowl
Surround and onto the Motor Drive
Coupling Push down until it clicks into
place. Ensure the Puree Disc is fitted
securely inside the Filter Bowl Surround
and onto the Motor Base.
3. Place the Puree Insert into the Filter
Bowl Surround, making sure the warning
label on the handle is facing upwards.
4. Place the Juicer Cover over the Puree
Insert and Filter Bowl Surround and
lower into position.
NOTE
Never use Puree Disc without Puree
Insert. They must always be used
together.
5. Raise the safety locking arm up and lock
into the two grooves on either side of
the juicer cover. The safety locking arm
should now be in a vertical position and
locked into place on top of the juicer
cover.
13
ASSEMBLING YOUR BREVILLE PRODUCT
6. Slide the food pusher down the feed
chute by aligning the groove in the food
pusher with the small protrusion on the
inside of the top of the feed chute (as
shown in step 5 of the juice extractor).
PREPARATION OF FRUIT &
VEGETABLES FOR PUREE DISC
• Only soft fruits should be used with the
Puree Disc.
• When using fruits with hard inedible
skins, such as mangoes, pineapple or
kiwi, always peel before juicing.
• When using fruits with a hard core such
as pineapple, always remove this before
juicing.
• All fruits with pits, hard seeds or stones
such as nectarines, peaches, mangoes
and apricots must be pitted or deseeded
before juicing.
• Passionfruit pulp, peeled kiwi and
berries can be processed without
removing seeds.
SPEED SELECTOR
TABLE
Apricots (stone
removed)
Bananas (peeled) 1
Kiwi (peeled) 1
Mangoes (peeled, stone
removed)
Melons (peeled) 1
Peaches (stone
removed)
Pears soft (stalks
removed)
Pineapple (peeled and
cored)
Raspberries 1
Strawberries (stalks
removed)
Tomatoes 1
Watermelon (peeled,
seeds removed)
SPEED USING
PUREE DISC
1
1
1
1
1
1
1
NOTE
When using the Puree Disc only
use Speed 1. Always ensure motor is
running before adding fruit and/or
vegetables to feed tube.
14
OPERATING
for your Breville product
PAge heAder.....
OPERATING YOUR BREVILLE PRODUCT
WITH THE JUICE NUTRI DISC™ OR
PUREE DISC
1. Wash your selection of fruit and/or
vegetables to prepare them for juicing.
WARNING
Do not put hard fruit and vegetables
(ie. Carrots , apples , fresh beetroot ,
etc.) or ice through juicer when using
Puree Disc. This could damage parts of
the unit.
2. Ensure the juicer is correctly assembled
– see assembling instructions. Ensure
the Nutri Disc™ or Puree Disc is
thoroughly cleaned before each use.
Ensure you place the Juice Jug (or glass)
under spout before commencing juicing.
3. Plug the power cord into a 110/120V
power outlet. The light surrounding the
‘Start | Stop” button will illuminate.
NOTE
The light will be illuminated for 2
minutes before fading into sleep
mode. The light will come back on by
activating any of the controls.
6. As fruits and vegetables are processed
juice will flow into the juice jug and the
separated pulp will accumulate in the
Pulp Container. The Pulp Container can
be emptied during juicing by turning the
juicer OFF at the control panel and then
carefully removing the Pulp Container.
Replace the empty Pulp Container into
position before continuing to juice.
NOTE
Do not allow the Pulp Container
to over fill as this may affect the
operation of the appliance.
NOTE
To minimize cleaning, line the pulp
container with a produce bag to
collect the pulp. Pulp can be used in
other dishes, or as a compost for the
garden or discarded.
4. Use the speed selector table as a guide
for juicing different fruit and vegetables.
Push the “Start | Stop” button and the
Juicer will automatically start.
5. With the motor running, place food into
the Feed Chute using the Food Pusher,
gently guide food down the Feed Chute.
Do not exert excess pressure. To extract
the maximum amount of juice, always
push the Food Pusher down slowly.
16
PAge heAder.....
OPERATING YOUR BREVILLE PRODUCT
USING THE PUREE DISC
When using the Puree Disc, puree will flow
into the juice jug. There will be no pulp
extracted into Pulp Container.
NOTE
SELF-RESET OVERHEATING
PROTECTION The Breville juicer
also fitted with a self-resetting safety
device which safeguards against
overheating on the motor with
excessive loads. If overheating occurs,
the juicer will automatically activate
the overheating protection device
and the motor will turn itself off. If
this occurs, the light surrounding
the Start|Stop button will flash red.
When the overheating protection
is activated, unplug the juicer from
power outlet for at least 15 minutes
to allow the unit to cool. Then plug
juicer into the power outlet and use as
normal.
NOTE
ELECTRONIC PROTECTION The
Breville juicer will automatically stop
operating if the motor is stalled. This
is an electronic safety feature. Either
too much food is being processed at
one time or the pieces are not small
enough. Try trimming food, cutting
food into smaller pieces of even size
and/or processing a smaller amount
per batch. If this occurs, the light
surrounding the Start|Stop button will
flash red. To continue juicing, turn
the power OFF at the control panel,
clear the feed chute, finally turn the
appliance back on by pressing the
Start|Stop button to ON.
NOTE
OVERLOAD PROTECTION BUTTON
The Breville juicer is fitted with
a safety device which safeguards
against overloading with excessive
loads. If this occurs, juicer will
automatically activate the overload
protection button and the unit will
turn itself off. If this occurs, remove
the plug from the outlet and allow the
unit to cool. Then press the Overload
Protection Button found on the bottom
of the Motor Base. The safety device
will then be reset and the Breville
juicer is ready for use again.
17
PAGE HEADER.....
DISASSEMBLING
your Breville product
18
PAge heAder.....
DISASSEMBLING YOUR BREVILLE PRODUCT
JUICE EXTRACTOR
1. Push the Start|Stop button on the
control panel of the Breville product to
turn off, then unplug the cord.
4. Move the Locking Arm down.
2. Remove the Pulp Container by holding
the handle and pivoting the bottom of
the Pulp Container away from the juicer
3. Place both hands on either side of the
Locking Arm and pull back and lift over
the grooves on either side of the
Juicer Cover.
5. Lift the Juicer Cover off the juicer.
6. To remove the Filter Bowl Surround,
hold base of juicer and turn Filter Bowl
Surround by the Juice Spout.
19
PAge heAder.....
DISASSEMBLING YOUR BREVILLE PRODUCT
7. Lift the Filter Bowl Surround off with the
Nutri Disc™ still in place.
Ultra sharp stainless steel Nutri Disc™
and teeth.
WARNING
8. To remove the Nutri Disc™, turn the
Filter Bowl Surround upside down and
carefully remove the Nutri Disc™
(it is recommended to remove the
Nutri Disc™ over the sink).
20
WARNING
The stainless steel filter Nutri Disc™
contains a titanium reinforced cutting
disc with super sharp blades and teeth.
Do not touch teeth or blades when
handling the Nutri Disc™.
PAge heAder.....
DISASSEMBLING YOUR BREVILLE PRODUCT
PUREE DISC
1. Push the Start|Stop button on the
control panel of the juicer Duo to turn
off, then unplug the cord.
2. Remove the Pulp Container by holding
the handle and pivoting the bottom of
the Pulp Container away from the juicer
3. Move the Locking Arm Down.
4. Lift the Juicer Cover off the juicer.
5. Lift the Puree insert from the
Filter Bowl surround.
21
PAge heAder.....
DISASSEMBLING YOUR BREVILLE PRODUCT
6. Lift the Puree Disc out of the Filter Bowl
Surround (be careful not to touch the
sharp cutting teeth).
WARNING
Ultra sharp stainless steel cutting disc
and teeth.
WARNING
The Puree Disc has super sharp blades
and teeth. Do not touch teeth or blades
when handling the Puree Disc
22
CARE AND CLEANING
CARE & CLEANING
• Always ensure that Breville juicer is
unplugged from the power outlet before
cleaning, disassembling or assembling
and storing the appliance.
• Follow these instructions to clean all
surfaces of parts that come into contact
with food during normal use.
• For easy cleaning- immediately after
each use rinse removable parts under
running water. Allow parts to air dry.
• After disassembling the unit all
removable parts may be washed in hot
soapy water, then rinsed well and dried.
• The Breville juicer Juice Cover, Filter
Bowl Surround, Pulp Container, Puree
Disc, Nutri Disc™ and Juice Jug are
dishwasher safe (Top Shelf only).
• Wipe the motor base with a damp cloth.
For consistent juicing results always ensure
that the Nutri Disc™ is thoroughly cleaned
using the supplied nylon brush. Using the
nylon washing brush, hold the Nutri Disc™
under running water and brush from the
inside of the disc to the upper rim of the
basket. Hold it up towards a light to ensure
the fine mesh holes are not blocked. If the
holes are blocked soak the Nutri Disc™ in
hot water with 10% lemon juice to loosen the
blocked holes. Alternatively, wash the Nutri
Disc™ in the dishwasher on the top shelf.
• Do not soak either the Nutri Disc™ or the
Puree Disc in bleach.
• Always treat the Nutri Disc™ and Puree
Disc with care as they can be
easily damaged.
• Discoloration of the plastic may
occur with brightly colored fruit and
vegetables. To help prevent this, wash
parts immediately after use.
• If discoloration does occur, the plastic
parts can be soaked in 10% lemon juice
and water or they can be cleaned with a
non abrasive cleaner.
NOTE
To assist with cleaning, soak the
Nutri Disc™ in hot soapy water
for approximately 10 minutes
immediately after juicing is
completed. If pulp is left to dry on
the filter it may clog the fine pores
of the filter mesh for lessening the
effectiveness of the Juicer. For your
convenience a nylon cleaning brush
has been included with your juicer.
NOTE
To minimize cleaning, line the pulp
container with a produce bag to
collect the pulp. Pulp can then be used
for other dishes, or as compost for the
garden or discarded.
NOTE
Do not wash the Food Pusher or the
Puree Insert in the dishwasher.
24
PAGE HEADER.....
TROUBLESHOOTING
25
TROUBLESHOOTING
POSSIBLE PROBLEM EASY SOLUTION
• The safety locking arm may not be correctly engaged
in the vertical operating position with the locking arm
located into the two grooves on either side of the juice
cover.
• Check the Overload Protection Button on the bottom of
the Motor Base to ensure the safety device has not been
activated or the overheating protection device has not
been activated automatically, if it has, allow more time
for the motor to cool down.
Motor appears to stall
when juicing
Excess pulp building up
in the mesh of the Nutri
Disc™
Pulp too wet and reduced
extracted juice
• Wet pulp can build up under the cover if the juicing
action is too vigorous. Try a slower juicing action by
pushing the food pusher down slower. Clean the Filter
Bowl Surround, the Nutri Disc™ and the juicer cover.
Select a faster speed for harder fruits and vegetables.
• The Breville juicer will automatically stop operating if
the motor is stalled. This is a electronic safety feature.
Either too much food is being processed at one time
or the pieces are not small enough. Try trimming food,
cutting food into smaller pieces of even size and/or
processing a smaller amount per batch. If this occurs,
the light surrounding the Start|Stop button will flash
red. To continue juicing, reset the Juicer by pressing
the Start|Stop button to OFF, then clear the feed chute,
finally turn the appliance back on by pressing the
Start|Stop button to ON.
• Hard fruits and vegetables will put excess strain onto
the motor if a low speed is selected. Please refer to the
juicing guide, to determine the correct speed for the
fruits and vegetables selected on juicing.
• Stop the juicing process. Remove the juicer cover and
remove the pulp. Re-assemble and begin juicing again.
Try alternating (soft and hard) vegetable and
fruit varieties.
• Try a slower juicing action. Remove Nutri Disc™ and
thoroughly clean mesh walls with the brush included.
Rinse Nutri Disc™ under hot water. If the mesh holes are
blocked, soak the Nutri Disc™ in a solution of hot water
with 10% lemon juice to unblock the holes or wash in the
dishwasher. This will remove excess fiber build up (from
fruit or vegetables) which could be inhibiting the juice
flow.
26
TROUBLESHOOTING
POSSIBLE PROBLEM EASY SOLUTION
Juice leaks between the
rim of the Juicer Cover
and the Filter Bowl
Surround
Juice sprays out too fast
from Juice Spout
When using Puree Disc
the Filter Bowl Surround
becomes full and clogs the
spout on the Filter Bowl
• Try a slower juicing action by pushing the food pusher
down slower. Fruit and vegetables with a high water
content (tomatoes and watermelon) should be juiced on
low speed or by using the Puree Disc.
• Try a slower juicing action by pushing the food pusher
down slower.
• Try using fruits with more water content to help flush
through the contents. Additionally, try a slower juicing
action by feeding one piece in at a time and by pushing
the food pusher down more slowly.
Surround.
Juicer suddenly turns off
during juicing
• The juicer has been stressed by overloading or stalling.
Juicer will automatically activate the overload protection
button and the unit will turn itself off. When this
happens it is recommended that the unit is turned off
and unplugged. Then press the Overload Protection
Button found on the bottom of the Motor Base. The
safety device will then be reset and the Breville juicer is
ready for use again.
Red light flashing • This may indicate that the motor has been stressed by
Overheating with excessive load. The Juicer is fitted
with a self-resetting safety device which safeguards
against overheating on the motor with excessive loads.
If overheating occurs, the juicer will automatically
activate the overheating protection device and the motor
will turn itself off. When the overheating protection is
activated, unplug the juicer from power outlet for at least
15 minutes to allow the unit to cool. Then plug juicer
into the power outlet and use as normal.
• The Juicer will automatically stop operating if the
motor is stalled. If this occurs, the light surrounding
the Start|Stop button will flash red. This is an electronic
safety feature. Either too much food is being processed
at one time or the pieces are not small enough. Try
trimming food, cutting food into smaller pieces of even
size and/or processing a smaller amount per batch. To
continue juicing, unplug the juicer from power outlet,
reset the Juicer by pressing the Start|Stop button to
OFF, then clear the feed chute, plug the juicer in and
finally turn the appliance back on by pressing the
Start|Stop button to ON.
27
Loading...