Breville BJE430 Instruction Book

the Juice Fountain™ Cold

Instruction Book - BJE430

Contents

2Breville Recommends Safety First

6Components

7Assembly

8Functions

10Care & Cleaning

11Troubleshooting

13Tips

16Recipes

20French

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

•Remove and safely discard any packaging material or stickers before using the juicer for the first time.

•To eliminate a choking remove and safely discard the protective cover fitted to the power plug of this appliance.

•Do not place the juicer near the edge of a countertop or table. Ensure the surface is level, clean and free of water and other substances.

•Always ensure the juicer is properly assembled before use.

•Always make sure the juicer filter basket, collector and top cover are fitted and clamped securely in place before the motor is turned on.

Do not unfasten clamps while the juicer is in operation.

Be sure to turn the switch to the OFF position after each use of your juicer. Make sure the motor stops completely before disassembling.

•We do not recommend children operate this juicer. Close adult supervision is necessary when operating this juicer near children.

•Do not use the juicer on a sink drain board.

•This appliance is for household use only. Do not use in any type of moving vehicles. Do not use the appliance outdoors, or for anything other than its intended use. Misuse can cause injury.

•To protect against risk of electric shock, do not immerse the cord, plug or motor base in water (or other liquids).

•Do not leave the juicer unattended when in use.

•Allow the motor to reach proper speed before pushing food through the feed chute.

•Never plug in or switch ON the juicer with food present in the feed chute.

•Unplug the cord from the power outlet when not in use, before putting on or taking off parts, before cleaning, storing, moving, or leaving the appliance unattended.

•To avoid serious injury, DO NOT put hands, fingers

or utensils into juicer opening while the unit is plugged in or during operation.

•If food becomes lodged in chute, ONLY use food pusher or another piece of fruit or vegetable to push it

down. When this method is not possible, turn the unit to OFF and disassemble juicer to remove obstruction.

•To disconnect, turn the control to OFF, then remove plug from wall outlet.

•Do not put your fingers or other objects into the juicer opening while it is in operation. If food becomes lodged in opening, use food pusher or another piece

of fruit or vegetable to push it down. When this method is not possible turn the motor off and disassemble juicer to remove the remaining food.

•Be careful when handling the filter basket as the small cutting blades at the base of

the filter basket are very sharp. Mishandling may cause injury.

•Before juicing any food, fruits or vegetables, inspect and clean to ensure the following;

−−all rinds and hard skin have been removed,

−−there are no pits, stones or heavy seeds,

−−packing or bundling ties and metal wire have been removed.

Not following the above instructions can lead to unsafe operation and may cause serious injury.

•Do not use the appliance if the rotating sieve (filter basket) is damaged.

•Avoid contacting moving parts.

•The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.

•Fully unwind the power cord before use.

•Do not operate without the pulp container in place.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

•Do not let the cord hang over the edge of a table, counter, or let touch a hot surface such as a stove. Do not place on or near a hot gas or electric burner or in a heated oven.

•Properly clean the unit and filter basket after each use to avoid leaks or overflow and ensure the unit operates as intended.

•It is recommended to regularly inspect the appliance and power cord. Do not use the appliance if there is damage to the power cord or plug, or after the appliance malfunctions or has been dropped or damaged in any way. If this occurs, immediately stop use and call Breville Consumer Support.

NOTE

If the motor stalls or strains under load, do not operate continuously for more than 10 seconds at

a time.

NOTE

If the juicer stops due to improper operation or if there is excessive noise, shaking, or vibration, turn the unit OFF and allow the filter to stop spinning

completely. Unplug the unit from the power outlet, disassemble and clean all components before properly reassembling.

If the above issues persist, stop use of the juicer and contact Breville Consumer Support.

BREVILLE ASSIST® PLUG

Your Breville appliance comes with a unique Assist® Plug, conveniently designed with a finger hole to ease removal from the power outlet.

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

SHORT CORD

INSTRUCTIONS

Your Breville appliance is fitted with a short power supply cord to reduce personal injury or property damage resulting from pulling, tripping or becoming entangled with a longer cord.

If an extension cord is used,

(1)the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance,

(2)the cord should be arranged so that it will not drape over the countertop or table-top where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.

CALIFORNIA PROPOSITION 65:

(Applicable to California residents only).

This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS

Components

A.Food pusher

(top shelf dishwasher safe)

B.Interlocking safety arm

Stops juicer operating without cover locked into place.

C.Juicer cover

(not dishwasher safe)

D.Stainless steel filter basket

(top shelf dishwasher safe)

E.Pulp container

(top shelf dishwasher safe)

F.2 speed control and off dial

G.Cord storage

Cord wraps around feet and clips into position under base.

H.Filter bowl surround

(top shelf dishwasher safe)

I.70 fl. oz. (2 liter) juice jug and sealing lid with built in froth separator

(not dishwasher safe).

J.Overload Protection LED

K.Juicing Nozzle

(top shelf dishwasher safe)

Can be placed over spout to juice directly into a cup.

Assembly

BEFORE FIRST USE

Before using your juicer for the first time, remove and safely discard any packaging materials and promotional stickers

and labels.

Ensure the power cord is unplugged.

Wash the filter bowl surround, filter basket, juicer cover, food pusher, pulp container and juice jug and lid in warm, soapy water with a soft cloth. Rinse and dry thoroughly.

1.Place motor base on a flat, dry surface such as a countertop. Ensure that the juicer is switched to OFF at the dial, and the power cord is unplugged.

2.Place filter bowl surround on top of the motor base.

3.Align the arrows at the base of the stainless steel filter basket with the arrows on the motor drive coupling and push down until it clicks into place to create a secure fit with the motor base.

4.Place the juicer cover over the filter bowl surround, positioning the lower part of the feed chute over the stainless steel filter basket.

5.Raise the safety locking arm up and locate into the two grooves on either side of the juice cover.

6.The safety locking arm should now be in a vertical position and locked into place on top of the juice cover.

7.Slide the food pusher down the food chute by aligning the groove in the food pusher, with the small protrusion on the inside of the top of the feed tube.

Food pusher groove

Small protrusion inside feed tube

8.Place the pulp container into position by tilting and lifting the motor base slightly. Insert the pulp container under the juicer cover on the left hand side ensuring it is supported by the juicer cover and motor base.

9.Place the juicer jug under the juice spout and place the lid to avoid splatter.

JUICE JUG

Juice can be preserved in the juice jug for up to 3 days by following these steps.

1.Lift the lid off the jug and rotate 180°

2.Press down firmly to replace the lid

3.Store juice in the fridge

NOTE

Storage time depends on the ingredients being juiced and the freshness of the fruit prior to juicing. Juice must be stored in the refrigerator between 32°F to 39°F.

Functions

1.Wash your selection of fruit and vegetables to be juiced. Most fruit and vegetables such as apples, carrots and cucumbers will not need to be cut or trimmed to size as these will fit whole into the feed chute. Ensure vegetables such as beets, carrots etc. have all soil removed, are washed well and trimmed of leaves before using.

2.Plug the power cord into a 120V power outlet. Adjust the speed to the desired setting. Turn the dial to either the LOW or HIGH setting depending on the type of fruit or vegetable being juiced. Use the speed selector as a guide for juicing different fruits and vegetables.

3.With the motor running, place food into the feed chute and use the food pusher to gently guide food down. To extract the maximum amount of juice, always push the food pusher down slowly.

4.As fruit and vegetables are processed, juice will flow into the juice jug and the separated pulp will accumulate in the pulp container.

SPEED SELECTOR GUIDE

Apples	High

Apricots (pit removed)	Low

Beets (trimmed)	High

Blueberries	Low

Broccoli	Low

Cabbage	Low

Carrots	High

Cauliflower	Low

Celery	High

Cucumber (peeled, optional)	Low

Cucumber, soft skinned	High

Fennel	High

Grapes (seedless)	Low

Kiwi Fruit (peeled)	Low

Kale	High

Mangoes (peeled, pit removed)	Low

Melons (peeled)	Low

Nectarines (pit removed)	Low

Oranges (peeled)	Low or High

Peaches (pit removed)	Low

Pears (stem removed)	Low or High

Pineapple (peeled, optional)	High

Plums (pit removed)	Low

Raspberries	Low

Tomatoes	Low

Watermelon (peeled)	Low

NOTE

•The pulp container can be emptied during juicing by turning the juicer OFF on the dial and then carefully removing the pulp container. Replace empty pulp container before continuing to juice.

•Do not allow the pulp container to overfill as this may affect the operation of the appliance.

•The juicer is fitted with a safety device which safeguards against overheating with excessive loads. If overheating occurs, the juicer will automatically activate the overload protection device and the unit will switch itself off. When the overload protection is activated, unplug the juicer

from the power outlet for at least 15 minutes to allow the unit to cool. Then plug juicer into the power outlet and use as normal.

WARNING

Never use fingers, hands or utensils to push food down the feed chute or to clear the feed chute. Always use the food pusher provided.

Caution: sharp blades

The stainless steel filter basket contains small sharp blades to cut and process fruit and vegetables. Avoid touching the blades when handling the filter basket.

Care & Cleaning

Ensure the juicer is turned off by turning the juicer dial to the OFF position. Then unplug the power cord.

CLEANING

Rinse all parts after use (except the motor base) under running water to clear away the majority of juice and pulp. Wash in warm soapy water with a soft cloth.

To avoid food drying on to the blades, mesh or transparent parts, rinse and wash as soon as possible after use.

PULP CONTAINER

To minimize cleaning, you can line the pulp container with a biodegradable bag to collect the pulp.

MOTOR BASE

To clean the motor base, wipe with a soft, damp cloth then dry thoroughly. Wipe any excess food particles from the power cord.

Do not immerse the motor base in liquids.

CLEANING AGENTS

Do not use abrasive scouring pads or cleaners on either the motor base or the jug, as they may scratch the surface. Use only warm soapy water with a soft cloth.

DISHWASHER

Wash all parts (except the motor base) in warm soapy water with a soft cloth.

The filter bowl surround, stainless steel filter basket, food pusher and pulp container are dishwasher safe. Wash on a standard cycle, on the top shelf only.

The juice cover and juice jug are not dishwasher safe.

FILTER BASKET

To ensure consistent juicing results, always clean the filter basket thoroughly immediately after use.

If pulp is left to dry, it may clog the fine pores of the filter mesh, which can effect juicing performance. The filter basket can be soaked in hot soapy water for 10 minutes,

if necessary.

Hold the filter basket under running water and use brush (supplied with the juicer) in a circular motion to clear away pulp from the inside of the basket, including the blades. Turn over to brush away pulp from the outside of the basket, and repeat

if necessary.

After cleaning, hold up towards a light source to check that the fine mesh pores are not blocked. If blocked, soak the filter basket in hot water with 10% lemon juice to loosen, and brush under running water again.

Do not soak the filter basket in bleach, harsh chemicals or abrasive cleansers.

Always treat the filter basket with care, as it can be easily damaged. Do not use if

there is any damage or deformation to the filter mesh.

Filter basket can be washed in the dishwasher (top shelf).

The center of the filter basket has an array of small, sharp blades. Do not touch these blades when handling the filter basket.

STUBBORN FOOD STAINS

Discoloration of the plastic may occur with strongly colored fruit and vegetables. To help prevent this, wash parts immediately after use.

If discoloration does occur, the plastic parts can be soaked in water with 10% lemon juice or can be cleaned with a non-abrasive cleaner.

Troubleshooting

Juicer will not work	•	The safety locking arm may not be correctly engaged in the vertical operating
when switched ON		position. Check the top cover is properly aligned and the locking arm is
	•	located firmly into the two grooves on either side of the juicer cover.
	•	Motor overload protection may have operated (see below).
Overheating with	•	The juicer is equipped with an internal self-resetting overload to prevent the
excessive loads		motor from damage under heavy or continuous loads. If the motor suddenly
		stops working, turn the dial to OFF, and unplug the unit from the power outlet.
		Allow the juicer to cool for up to 30 minutes before operating again.
		NOTE: The unit MUST be unplugged from the power outlet in order for it to
	•	cool and be reset.
	•	Despite this overload protector, we suggest juicing in smaller batches, without
		excessive pushing force, to avoid overheating and stalling and to maintain the
		life of the motor.

Excess pulp building	•	Stop juicing, disassemble to scoop excess pulp off the juicer cover.
up in the stainless		Reassemble and continue juicing. Alternating soft and hard ingredients may
steel filter basket		help avoid this.

Pulp too wet and	•	The cleaner the filter, the better the juice yield, and dryer the pulp. Be sure to
reduced extracted juice		thoroughly clean the juicer as soon as possible after each use. Remove the
		stainless steel filter basket and thoroughly clean mesh walls with a cleaning
		brush. Rinse the filter basket under hot water. If the fine mesh holes are
		blocked, soak the basket in a solution of hot water with 10% lemon juice to
		unlock the holes or wash in the dishwasher (top shelf). This will remove excess
		fiber build up (from fruit and vegetables) which could be inhibiting the flow.

Juice leaks between	•	Try a slower juicing speed and push the food pusher down the feed chute
the rim of the juicer		more slowly.
and the juicer cover

Juice sprays out	•	The juice is being extracted too fast: try a slower juicing speed (if possible)
from spout		and push the food pusher down the feed chute more slowly.

Motor appears to	•	Wet pulp can build up under the juicer cover and stall the juicer if the juicer is
stall when overload		used excessively without cleaning. If this occurs, disassemble and follow the
protection LED flashes		cleaning instructions to clean the filter bowl surround, the stainless steel filter
		basket and the juicer cover. The juicer can also stall if excessive force is used
		to push produce down the feed chute. If this occurs, ensure that a more gentle
	•	pressure is used to push produce down the chute.
	•	The juicer will automatically stop operating if either too much food is being
		processed at one time or the pieces are not small enough. Try trimming the
		food or cutting into smaller pieces of even size and processing a smaller
		amount per batch. To continue juicing, reset the juicer by turning the juicer
	•	OFF and back ON.
	•	Allow the motor to reach full speed before putting ingredients in the chute.
		Pressing ingredients down before the juicer reaches full speed can cause the
		motor to stall or overload. Use gentle to moderate pressure on the pusher.
	•	Lower pressure produces a better juice yield.
	•	Hard fruit and vegetables will put excess strain onto the motor if a low speed
		is selected. Refer to the juicing guide to determine the correct speed for the
		fruit and vegetables selected for juicing.

Overload protection	•	This indicates the motor speed is slowed down to a not-efficient level. This
LED light flashing		may be caused by too heavy pushing force on the pusher or too much pulps
during the use		sticking onto the lid or in pulp pin. Using proper pushing force on the food
		pusher or regularly clean the lid and pulp bin can prevent this situation to
		happen.

Overload Protection	•	This indicates motor overload protection is activated. To reset the unit, unplug
LED is on		the unit from power and let the motor cool down for 10 to 15 minutes, and
		plug the power on again.

If any of the above issues persist, or if you have questions, stop use of the juicer and contact Breville Consumer Support.

+ 28 hidden pages