Breville BJB840XL User Manual

The Juice & Blend
Instruction Booklet
Juice & Blend
Instruction Book - Livret d’instructions
BJB840XL
BJB840XL_IB_D10_FA.indd 1 16/08/10 10:02 AM
CONGRATULATIONS
On the purchase of your new
BJB840XL_IB_D10_FA.indd 2 16/08/10 10:02 AM
CONTENTS
4 Breville recommends safety first
7 Use as a Juice Extractor 8 Know your Breville Juice Extractor 10 Assembling the Juice Extractor 13 Operating the Juice Extractor 17 Disassembling the Juice Extractor 20 Cleaning the Juice Extractor 22 Juice Extractor Troubleshooting
27 Use as a Blender 28 Know your Breville Blender 30 Assembling the Blender 33 Operating the Blender 37 Disassembling the Blender 39 Cleaning the Blender 41 Blending tips 43 Blender Troubleshooting
47 Recipes 69 One year limited warranty
3
BJB840XL_IB_D10_FA.indd 3 16/08/10 10:02 AM
BREVILLE RECOMMENDS SAFETY FIRST
We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions:
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
• Carefully read all instructions before
operating the appliance for the first time and save for future reference.
• Remove and safely discard any
packaging materials and promotional labels before using the appliance for the first time.
• To eliminate a choking hazard for young
children, remove and safely discard the protective cover fitted to the power plug of this appliance.
• To protect against electrical shock, do
not immerse the power cord, power plug or motor base in water or any other liquid.
• Always use the appliance on a dry,
level surface.
• Do not use the appliance on a sink
drain board.
• Do not place the appliance near the
edge of a bench or table during operation. Vibration during operation may cause the appliance to move.
• Do not place the appliance on or near
a hot gas or electric burner, or where it could touch any other source of heat.
• Unwind the power cord fully before use.
• Do not allow the power cord to hang
over the edge of a table or counter, touch hot surfaces or become knotted.
• Always ensure the appliance is
completely assembled before connecting to the power outlet and operating. The appliance will not turn on unless properly assembled. Follow the instructions provided in this book.
• Always make sure the safety locking bar
is securely in place before the motor is turned on. Do not unfasten the safety locking bar while the appliance is in operation.
• Always avoid contact with moving parts.
• Strictly follow the care and cleaning
instructions described in this book.
• This appliance is for household use only.
Do not use the appliance for anything other than its intended purpose as described in this book. Do not use outdoors. Do not use in moving vehicles or boats.
• The use of attachments not sold or
recommended by Breville may cause fire, electric shock or injury.
• Do not leave the appliance unattended
when in use.
4
BJB840XL_IB_D10_FA.indd 4 16/08/10 10:02 AM
BREVILLE RECOMMENDS SAFETY FIRST
• Regularly inspect the power cord, power
plug and actual appliance for any damage. Do not operate if damaged in any way or after the appliance malfunctions. Immediately cease use of the appliance and visit www.Breville.com or call Breville Customer Service on 1-866-BREVILLE for replacement, repair or adjustment.
• For any maintenance other than
cleaning, visit www.Breville.com or call Breville Customer Service at 1-866-BREVILLE.
WHEN USING THE APPLIANCE AS A JUICE EXTRACTOR
• Do not operate the juice extractor
without the pulp container in place
• Do not use the juice extractor if the
rotating filter basket is damaged.
• Do not touch the small sharp teeth and
blades in the center of the filter basket.
• Do not touch the blade in the feed chute.
• Do not push produce into the feed chute
with your fingers. Always use the food pusher provided.
• Do not load feed chute with food before
the motor is running.
• Do not juice stone fruit unless seeds
and/or stones have been removed.
• Always switch the juice extractor off
after each use. Ensure the motor stops completely and unplug the power cord from the wall outlet before attempting to move the appliance, before cleaning, disassembling, assembling and when storing the appliance.
WARNING
Super wide feed chute. Do not place hands or foreign objects down
feed
chute, always use food pusher provided.
WHEN USING THE APPLIANCE AS A BLENDER
• Do not place hands in the blending jug
unless the appliance is disconnected from the power outlet. A spatula may be used but only when the blender is not running.
• Always operate the blender with the
blender jug lid in place.
• Do not use the blender for any purpose
other than food or beverage preparation.
• Do not process boiling liquids. Let the
liquid cool slightly before placing in the blending jug. Remove the inner lid from the blender jug lid before blending.
• Always switch the blender off after
each use. Ensure the motor stops completely and unplug the power cord from the wall outlet before attempting to move the appliance, before cleaning, disassembling, assembling and when storing the appliance.
WARNING
Blender blades are sharp. Handle carefully.
NOTE
The maximum rating is based on the juice extractor attachment which draws the greatest power.
5
5
BJB840XL_IB_D10_FA.indd 5 16/08/10 10:02 AM
BREVILLE RECOMMENDS SAFETY FIRST
BREVILLE ASSIST™ PLUG
Your Breville appliance comes with a unique Assist™ Plug, conveniently designed with a finger hole in the power plug for easy and safe removal from the wall outlet. For safety reasons it is recommended you plug your Breville appliance directly into its own electrical outlet on a dedicated circuit separate from other appliances. If the electric circuit is overloaded with other appliances, your appliance may not function properly. Use in conjunction with a power strip or extension cord is not recommended.
SHORT CORD INSTRUCTIONS
Your Breville appliance is fitted with a short power supply cord as a safety precaution to prevent personal injury or property damage resulting from pulling, tripping or becoming entangled with a longer cord. Do not allow children to use or be near this appliance without close adult supervision. Longer detachable power strips or extension cords are not recommended but may be used if care is exercised. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.
FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS
6
BJB840XL_IB_D10_FA.indd 6 16/08/10 10:02 AM
USE AS A
JUICE EXTRACTOR
BJB840XL_IB_D10_FA.indd 7 16/08/10 10:02 AM
KNOW YOUR BREVILLE JUICE EXTRACTOR
C
D
A
B
N
E
L
F
M
G
H
I
J
K
8
BJB840XL_IB_D10_FA.indd 8 16/08/10 10:02 AM
KNOW YOUR BREVILLE JUICE EXTRACTOR
A. Food Pusher B. Juicer Cover with Feed Chute C. Pulp Container D. Juicing Speed Guide E. Filter Basket F. Filter Bowl Surround G. Motor Drive Coupling H. Motor Base I. Safety Locking Arm J. START | OFF button and speed
control dial
K. OVERLOAD RESET button
(underside of the Motor Base)
L. Juicing Jug Lid M. 40oz (1.2L) Juicing Jug N. Nylon Cleaning Brush
9
BJB840XL_IB_D10_FA.indd 9 16/08/10 10:02 AM
ASSEMBLING
your Breville Juice Extractor
BJB840XL_IB_D10_FA.indd 10 16/08/10 10:02 AM
PAGE HEADER.....ASSEMBLING THE JUICE EXTRACTOR
ASSEMBLING THE JUICE EXTRACTOR
Before using the Juice Extractor for the first time, remove and safely discard any packaging material and promotional labels. Ensure the power cord is unplugged from the wall outlet.
Wipe the Motor Base with a damp cloth. Dry thoroughly.
Wash the Filter Bowl Surround, Filter Basket, Juicer Cover, Food Pusher, Juice Jug, Juice Jug Lid and Pulp Container in warm soapy water with a soft cloth or nylon brush. Rinse and dry thoroughly. Alternatively, place these parts, excluding the Food Pusher, in the dishwasher.
1. Place the Motor Base on a flat dry
surface such as a bench top. Ensure the power cord is unplugged from the wall outlet.
2. Place the Filter Bowl Surround on top
of the Motor Base.
3. Align the arrows on the Filter Basket
with the arrows on the Motor Drive Coupling and push down until it clicks into place. Ensure the Filter Basket is fitted securely inside the Filter Bowl Surround and onto the Motor Base.
4.
Lower the Juicer Cover, positioning the rim within the Filter Bowl Surround.
11
BJB840XL_IB_D10_FA.indd 11 16/08/10 10:02 AM
PAGE HEADER.....ASSEMBLING THE JUICE EXTRACTOR
5. Raise the Safety Locking Arm and lock
into the two grooves on either side of the Juicer Cover. The Safety Locking Arm should now be in a vertical position.
6.
Slide the Food Pusher down the Feed Chute by aligning the groove in the Food Pusher with the small protrusion on the inside top of the Feed Chute.
7. Place the Pulp Container into position
by tilting slightly.
Tip:
• To minimize clean up, place a plastic
freezer bag (or plastic grocery bag) into the Pulp Container to collect the pulp.
8.
Place the provided Juice Jug under the spout on the right hand side. Ensure the Juice Jug Lid is used to avoid any splatter.
NOTE
A glass could also be used to collect juice.
12
BJB840XL_IB_D10_FA.indd 12 16/08/10 10:02 AM
OPERATING
your Breville Juice Extractor
BJB840XL_IB_D10_FA.indd 13 16/08/10 10:02 AM
OPERATING THE JUICE EXTRACTOR
OPERATING THE JUICE EXTRACTOR
1. Wash and prepare your selection of fruit
and/or vegetables :
Fruits with hard or inedible skins such as citrus fruit, melons and kiwi fruit should be peeled before juicing. Pineapple can be juiced with or without the rind removed.
Fruits with pits, hard seeds or stones such as nectarines, peaches, mangoes, apricots, plums and cherries must be pitted before juicing.
2. Ensure the Juice Extractor is correctly
assembled with the Safety Locking Arm securely locked into the vertical position and the Juice Jug under the spout.
NOTE
As a safety precaution, the Juice Extractor will not operate if the Safety Locking Arm is not securely locked into the vertical position.
3. Plug the power cord into a 110/120V
wall outlet. The START | OFF button surround will illuminate.
NOTE
The button surround will illuminate for 2 minutes before entering stand­by mode. To re-activate the Juice Extractor out of stand-by mode, press or turn the START | OFF button.
FOOD TO BE JUICED Speed
Apples 5 Apricots (stone removed) 2 Beets (cleaned, trimmed) 5 Blueberries 1 Broccoli 4 Brussel sprouts (trimmed) 5 Cabbage 4 Carrot 5 Cauliflower 4 Celery 5 Cucumber, soft skinned 4 Fennel 5 Grapes (seedless) 1 Kiwi fruit (peeled) 2 Mangoes (peeled, stone re-
2
moved) Melons (peeled) 1 Nectarines (stone removed) 2 Oranges (peeled) 3 Peaches (stone removed) 2 Pears hard (stalks removed) 5 Pears soft (stalks removed) 2 Pineapple 5 Plums (stone removed) 2 Raspberries 1 Tomatoes 1 Watermelon (peeled) 1
14
BJB840XL_IB_D10_FA.indd 14 16/08/10 10:02 AM
OPERATING THE JUICE EXTRACTOR
4. Rotate the START | OFF button to
the desired speed. Use the speed selector table on page 14 as a guide for juicing different fruit and vegetables. For your convenience, a juicing speed guide is also printed on the inside of the Pulp Container.
NOTE
The SMOOTHIE, ICE and PULSE settings can only be selected when the appliance is assembled as a blender.
5. Push the START | OFF button. With the
motor running, place food into the Feed Chute.
IMPORTANT:
Do not load the Feed Chute with food until the motor is running.
6. Using the Food Pusher, gently guide
food down the Feed Chute. Do not exert excess pressure. To extract the maximum amount of juice, always push the Food Pusher down slowly.
Tips:
• A small amount of lemon juice can be
added to the fruit and/or vegetables to inhibit browning.
• When juicing herbs, sprouts or leafy
green vegetables, either wrap them together to form a bundle or juice them in the middle of a combination of ingredients on low speed to obtain the best extraction. If only juicing herbs or leafy green vegetables, the juice yield will be low due to the nature of centrifugal juicing. It is advised to juice them with a combination of other fruits and vegetables.
• When juicing different ingredients of
varying textures, start with the softer textured ingredients on low speed then change to high speed for harder textured ingredients. This assists in extracting the maximum amount of juice by clearing the Filter Basket between ingredients.
7. As fruits and vegetables are processed,
juice will flow into the Juice Jug and the separated pulp will accumulate in the Pulp Container.
NOTE
The Pulp Container can be emptied during juicing by turning the Juice Extractor off and then carefully removing the Pulp Container. Replace the empty Pulp Container into position before continuing to juice. Do not allow the Pulp Container to over-fill as this may affect the operation of the appliance.
8. Immediately after each use, use the
provided nylon brush to thoroughly clean the fine mesh holes of the Filter Basket and rinse the remaining removable parts under running water. For more cleaning information, refer to ‘Cleaning the Juice Extractor’ on page 20.
15
BJB840XL_IB_D10_FA.indd 15 16/08/10 10:02 AM
OPERATING THE JUICE EXTRACTOR
The Breville Juice & Blend is fitted with protection devices as a safety precaution to prevent both personal injury and damage to the appliance.
OVERLOAD PROTECTION
This protection device safeguards against overloading the motor with excessive loads.
If overloading occurs, the Overload Protection will automatically de-activate the motor. When this occurs, unplug the power cord from the wall outlet and press the OVERLOAD RESET button found on the underside of the Motor Base. This will reset the Overload Protection, enabling you to reconnect the power cord to the wall outlet and recommence normal use.
OVERHEAT PROTECTION
This protection device safeguards against overheating of the motor with excessive loads.
If overheating occurs, the START | OFF button surround will flash red and the Overheat Protection will automatically de-activate the motor. When this occurs, unplug the power cord from the wall outlet and allow the appliance to cool for at least 15 minutes. Then reconnect the power cord to the wall outlet and recommence normal use.
ELECTRONIC PROTECTION
This protection device will automatically de-activate the motor if the motor is stalled.
If the motor stalls, the START | OFF button surround will flash red and the Electronic Protection will automatically de-activate the motor. When this occurs, unplug the power cord from the wall outlet and clear the Feed Chute. Either too much food is being processed at one time or the pieces are not small enough. Try trimming food, cutting food into smaller pieces of even size and/ or processing a smaller amount per batch. Then reconnect the power cord to the wall outlet and recommence normal use.
16
BJB840XL_IB_D10_FA.indd 16 16/08/10 10:02 AM
DISASSEMBLING
your Breville Juice Extractor
BJB840XL_IB_D10_FA.indd 17 16/08/10 10:02 AM
PAGE HEADER.....DISASSEMBLING THE JUICE EXTRACTOR
DISASSEMBLING THE JUICE EXTRACTOR
1. Ensure the Juice Extractor is turned off
and the power cord is unplugged from the wall outlet.
2. Grip the handle around the top rim
of the Pulp Container, then pivot the bottom of the Pulp Container away from the Juice Extractor.
3. Pull the Safety Locking Arm downwards
and over the grooves on either side of the Juicer Cover.
4.
Remove the Food Pusher from the Feed Chute.
5. Lift the Juicer Cover off the Filter
Bowl Surround.
6. To remove the Filter Bowl Surround,
hold the Motor Base then turn the Filter Bowl Surround by the Juice Spout. The Filter Bowl Surround should lift off the Motor Base with the Filter Basket still in place.
7. To remove the Filter Basket from the
Filter Bowl Surround, turn the Filter Bowl Surround upside down over the sink.
18
BJB840XL_IB_D10_FA.indd 18 16/08/10 10:02 AM
PAGE HEADER.....DISASSEMBLING THE JUICE EXTRACTOR
WARNING
The Filter Basket contains a titanium reinforced cutting disc with ultra sharp blades and teeth. Do not touch blades and teeth when handling the Filter Basket.
19
BJB840XL_IB_D10_FA.indd 19 16/08/10 10:02 AM
CLEANING
your Breville Juice Extractor
BJB840XL_IB_D10_FA.indd 20 16/08/10 10:02 AM
PAGE HEADER.....CLEANING THE JUICE EXTRACTOR
Always ensure that the power cord is unplugged from the wall outlet before cleaning, disassembling or assembling and storing the appliance.
1. Immediately after each use, use the
provided nylon brush to thoroughly clean the fine mesh holes of the Filter Basket. Brush the inside of the Filter Basket under running water, holding it up towards a light to ensure the fine mesh holes are not blocked. If the holes are blocked, soak the Filter Basket in hot water with 10% lemon juice to loosen the blocked holes. Alternatively, immediately after each use, wash the Filter Basket in the dishwasher then allow to air dry.
Tips:
• If the Filter Basket cannot be cleaned
immediately after use, soak the Filter Basket in hot soapy water immediately after juicing is complete. If pulp is left to dry on the Filter Basket, it may clog the fine mesh holes, thereby lessening the effectiveness of the Juice Extractor.
• Do not soak the Filter Basket in bleach.
WARNING
The Filter Basket contains a titanium reinforced cutting disc with ultra sharp blades and teeth. Do not touch blades and teeth when handling the Filter Basket.
2. Wash the Filter Bowl Surround, Juicer
Cover, Food Pusher, Juice Jug, Juice Jug Lid and Pulp Container in warm soapy water with the provided nylon brush or a soft cloth. Rinse and dry thoroughly. Alternatively, place these parts, excluding the Food Pusher, in the dishwasher.
NOTE
Do not wash the Food Pusher in the dishwasher.
Tips:
• Discoloration of the plastic parts may
occur with strongly colored fruit and vegetables. To help prevent this, wash parts immediately after use.
• If discoloration does occur, the plastic
parts can be soaked in 10% lemon juice and water or they can be cleaned with a non abrasive cleaner.
3. Wipe the Motor base with a soft damp
cloth and dry thoroughly. Do not use abrasive scouring pads or cleaners when cleaning the Motor Base as these may scratch the surface. Wipe any excess food particles from the power cord.
21
BJB840XL_IB_D10_FA.indd 21 16/08/10 10:02 AM
TROUBLESHOOTING
your Breville Juice Extractor
BJB840XL_IB_D10_FA.indd 22 16/08/10 10:02 AM
JUICE EXTRACTOR TROUBLESHOOTING
PROBLEM EASY SOLUTION
Juice Extractor will not work or suddenly switches off during juicing
• Check that the power plug is securely inserted into
wall outlet.
• Insert the power plug into an independent outlet.
• Insert the power plug into a different outlet.
• Reset the circuit breaker if necessary.
• Ensure the indicator on the START | OFF button is
aligned directly with the desired speed. The juicer may slow down and automatically stop if the indictor is incorrectly aligned.
• Ensure the Safety Locking Arm is in the upright
position and is securely locked into the two grooves on either side of the Juicer Cover (see page 12).
• The Overload Protection may have automatically
de-activated the motor. Unplug the power cord from the wall outlet and press the OVERLOAD RESET button found on the underside of the Motor Base. This will reset the Overload Protection, enabling you to reconnect the power cord to the wall outlet and recommence normal use (see page 16).
• The Overheat Protection may have automatically
de-activated the motor. Unplug the power cord from the wall outlet and allow the appliance to cool for at least 15 minutes. Insufficient cooling time may result in the motor de-activating again. After sufficient cooling time, reconnect the power cord to the wall outlet and recommence normal use (see page 16).
• The Electronic Protection may have automatically
de-activated the motor. Unplug the power cord from the wall outlet and clear the Feed Chute. Either too much food is being processed at one time or the pieces are not small enough. Try trimming food, cutting food into smaller pieces of even size and/ or processing a smaller amount per batch. Then reconnect the power cord to the wall outlet and recommence normal use (see page 16).
23
BJB840XL_IB_D10_FA.indd 23 16/08/10 10:02 AM
JUICE EXTRACTOR TROUBLESHOOTING
PROBLEM EASY SOLUTION
Motor appears to stall when juicing
Excess pulp building up in the mesh of the Filter Basket
• The Electronic Protection device will automatically
de-activate the motor if the motor is stalled. Unplug the power cord from the wall outlet and clear the Feed Chute. Either too much food is being processed at one time or the pieces are not small enough. Try trimming food, cutting food into smaller pieces of even size and/or processing a smaller amount per batch. Then reconnect the power cord to the wall outlet and recommence normal use (see page 16).
• Ensure the motor is running before loading the Feed
Chute with food.
• Wet pulp can build up under the Juicer Cover if
the juicing action is too vigorous. Stop the juicing process and remove the power cord from the wall outlet. Clean the Juicer Cover, Filter Bowl Surround and Filter Basket. Reconnect the power cord to the wall outlet and recommence juicing with a slower juicing action by pushing the Food Pusher down more slowly.
• Hard fruits and vegetables will put excess strain
onto the motor if a low speed is selected. Refer to the speed selector table on page 14 to determine the recommended speed for the selected fruits and vegetables.
• Stop the juicing process and remove the power
cord from the wall outlet. Clean the Juicer Cover, Filter Bowl Surround and Filter Basket. Reconnect the power cord to the wall outlet and recommence juicing. Try alternating soft and hard fruits and vegetables, starting with the softer textured ingredients on low speed then changing to high speed for harder textured ingredients. This assists in extracting the maximum amount of juice by clearing the Filter Basket between ingredients.
24
BJB840XL_IB_D10_FA.indd 24 16/08/10 10:02 AM
JUICE EXTRACTOR TROUBLESHOOTING
PROBLEM EASY SOLUTION
Very wet pulp and reduced juice extraction
I cannot select the SMOOTHIE, ICE or PULSE settings
Juice leaks between the rim of the Juicer Cover and the Filter Bowl Surround
• Juice with a slower juicing action by pushing the
Food Pusher down more slowly.
• Stop the juicing process and remove the power
cord from the wall outlet. Use the provided nylon brush to thoroughly clean the fine mesh holes of the Filter Basket. Brush the inside of the Filter Basket under running water, holding it up towards a light to ensure the fine mesh holes are not blocked. If the holes are blocked, soak the Filter Basket in hot water with 10% lemon juice to loosen the blocked holes. Alternatively, wash the Filter Basket in the dishwasher. Cleaning the Filter Basket will remove excess fiber build up (from juicing the fruit or vegetables) which could be inhibiting the juice flow.
• These settings can only be selected when the
appliance is assembled as a blender.
• Juice with a slower juicing action by pushing the
Food Pusher down more slowly.
• Fruit and vegetables with a high water content, for
example tomatoes and watermelon, should be juiced on low speed.
• Ensure the Juice Extractor is correctly assembled
(see page 12). The rim of the Juicer Cover should be securely positioned within the Pulp Container and Filter Bowl Surround.
Juice sprays out too fast from the Juice Spout
BJB840XL_IB_D10_FA.indd 25 16/08/10 10:02 AM
• Juice with a slower juicing action by pushing the
Food Pusher down more slowly.
25
JUICE EXTRACTOR TROUBLESHOOTING
PROBLEM EASY SOLUTION
Red light flashing • The Overheat Protection may have automatically de-
activated the motor. If this occurs, the START | OFF button surround will flash red. Unplug the power cord from the wall outlet and allow the appliance to cool for at least 15 minutes. Insufficient cooling time may result in the motor de-activating again. After sufficient cooling time, reconnect the power cord to the wall outlet and recommence normal use (see page 16).
• The Electronic Protection may have automatically
de-activated the motor. If this occurs, the START | OFF button surround will flash red. Unplug the power cord from the wall outlet and clear the Feed Chute. Either too much food is being processed at one time or the pieces are not small enough. Try trimming food, cutting food into smaller pieces of even size and/or processing a smaller amount per batch. Then reconnect the power cord to the wall outlet and recommence normal use (see page 16).
26
BJB840XL_IB_D10_FA.indd 26 16/08/10 10:02 AM
USE AS A BLENDER
BJB840XL_IB_D10_FA.indd 27 16/08/10 10:02 AM
KNOW YOUR BREVILLE BLENDER
B
C
A
D
F
E
G
H
I
J
K
28
BJB840XL_IB_D10_FA.indd 28 16/08/10 10:02 AM
KNOW YOUR BREVILLE BLENDER
A. Inner Lid B. Lid with Breville Assist™
ring-pull removal
C. 51oz (1.5L) Blender Jug D. Removable Silicon Gasket E. Removable Blade Assembly F. Blade Removal Tool G. Motor Drive Coupling H. Motor Base I. Safety Locking Arm J. START | OFF button and speed
control dial
K. OVERLOAD RESET button
(underside of the Motor Base)
29
BJB840XL_IB_D10_FA.indd 29 16/08/10 10:02 AM
ASSEMBLING
your Breville Blender
BJB840XL_IB_D10_FA.indd 30 16/08/10 10:02 AM
Loading...
+ 110 hidden pages