BRAUN Triumph Professional Care 9900 User Manual [fr]

Oral-B

ROFESSIONAL CARE 9900/SOINS PROFESSIONELS 9900

SANS FIL

WIRELESS

WITH

AVEC ÉCRAN

WIRELESS

powered

English 4

Español 13

Français 22

Internet:

www.oralb.com www.braun.com www.service.braun.com www.oralb.ca

Braun GmbH Frankfurter Straße 145 61476 Kronberg/Germany

D 30.546.4 X D 30.546.4 D 30.526.4 X D 30.516.4

Type 3731 Modelo 3731 Modèle 3731

98973812/VII-09 GB/E/F Printed in Germany Impreso en Alemania Imprimé en Allemagne

Oral-B

Oral-

IMPORTANT SAFEGUARDS

Oral-B Triumph™ as been carefully designed to offer you and your family a unique brushing experience that is both safe and effective. When using electrical products, however, basic safety precautions should always be followed.

Read all instructions before using.

DANGER

In order to reduce the risk of electrocution:

1. Do not place or store the charger where it can fall or be pulled into a tub or sink.

2. Do not place the charger in water or other liquid.

3. Do not reach for a charger that has fallen into water. Unplug immediately.

4. Do not use while bathing.

WARNING

To reduce the risk of burns, electrocution, fire or injury:

1. This appliance is not intended for use by children or persons with reduced physical or mental capabilities, unless they are supervised by a person responsible for their safety.

2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

3. Keep cord away from heated surfaces.

4. Never drop the appliance or insert any object into any opening of the appliance.

5. Never operate this product if it has been dropped or damaged, if it is not working properly, or if the SmartPlug is damaged or has been dropped into water. If any of these occur, please contact a service center and return the product for examination and repair.

6. If the product is dropped, the brush head should be replaced before the next use even if no damage is visible.

This appliance is provided with a SmartPlug with integrated Safety Extra Low Voltage

power supply. Do not exchange or manipulate any part of it otherwise there is the risk of electric shock. Periodically check the SmartPlug for damage. A damaged or nonfunctioning appliance should no longer be used. Take it to an Oral-B Braun Service Center.

IMPORTANT

1. Do not touch the power plug with wet hands. This can cause an electric shock.

2. When unplugging, always hold the power plug instead of the cord.

3. Do not modify the product. Do not disassemble or repair. This may cause fire, electric shock or injury. Consult your dealer for repairs or contact an Oral-B Braun Service center.

4. Do not disassemble the product except when disposing of the battery.

5. When taking out the battery for disposal, use caution not to short the positive (+) and negative (–) terminals.

6. This product is not intended for use by children under age three.

CAUTION

If you are undergoing treatment for any oral care condition, consult your dental professional prior to use.

SAVE THESE INSTRUCTIONS

English

h/min

set

h/min

set

h/min

set

h/min

set

New Oral-B Triumph now with SmartGuide uses an interactive wireless display to help you optimize your brushing experience.

Important

• To avoid electromagnetic interference and/or

compatibility conflicts, deactivate the radio transmission of your toothbrush before carrying or using it in restricted surroundings such as aircrafts or specially marked areas in hospitals (see «Deactivating the radio transmission»).

back and insert the two batteries (type AA) with correct polarity (see symbol in the battery compartment).

h/min

set

h/min

set

• A flashing «12:00» on the SmartGuide display indicates that time can be adjusted. Press the «set» button, located in the battery compartment, until «12h» is displayed.

• Persons with pacemakers should always keep the toothbrush more than six inches (15 centimeters) from the pacemaker when turned on. If at any time you suspect interference is taking place, deactivate the radio transmission of your toothbrush before using it (see «Deactivating the radio transmission»).

Description

a Oral-B® FlossAction™ brush head b On/off button c Mode button d Handle e Handle display f SmartPlug charger (includes charging ring

and SmartPlug) g Base plate h Base station i Protective cover j Oral-B

ProWhite™ brush head (not with all

models) k SmartGuide display unit l Wall mount m Adhesive tape

First use

set

h/min

• By briefly pressing the «h/min» button, you can toggle between a «12h» or «24h» daytime format. Push the «set» button to confirm your choice.

• Then the hour digit starts flashing. Press the «h/min» button until the right hour appears and confirm with the «set» button. Proceed the same way to set both minute digits. If you prefer not using this clock feature, the flashing «12:00» will disappear automatically after 24h.

You can start your toothbrush by pressing the on/off button (b). To avoid splashing, guide the brush head to your teeth before switching the appliance on.

Before brushing for the first time, charge your toothbrush. Plug the SmartPlug into an electrical outlet and place the handle (d) on the charging ring (see «Connecting and charging»).

• To activate the SmartGuide display unit (k), remove the battery compartment cover on the

ral-B

ral-B O

Oral-B

Connecting and charging

Your toothbrush has a waterproof handle, is electrically safe and is designed for use in the bathroom.

To assemble the base station (h) as charging unit, detach the base plate (g) first ( Place the charging ring into the base station and attach the base plate as shown ( page 3). Then insert the protective cover (i) on the back of your base station (see diagram page 3).

• Plug the SmartPlug into an electrical outlet and place the toothbrush handle (d) on the charging unit. A battery symbol should appear in the handle display (e). The battery symbol will fill up while the handle is being charged. Once the handle is fully charged, the battery symbol is completely filled with four bars. A full charge takes at least 12 hours to complete and allows for approximately two weeks of regular brushing (twice a day, 2 minutes).

1, page 3).

2 and 3,

• To maintain the maximum capacity of the rechargeable battery, unplug the charging unit and fully discharge the handle by regular use at least every 6 months.

For electric specifications, see printing on the SmartPlug.

Personalizing the timer

You can choose between the «Professional» or «2-Minute» timer and a «Count Up» or «Count Down» timer to meet your specific needs.

The «2-Minute Timer» indicates by a long stuttering sound and a «smiley» on the SmartGuide display unit that the dentist recommended 2-minute brushing time has been reached. In addition, the «Professional Timer» helps you brush all four quadrants of your mouth equally. It signals with a short stuttering sound at 30-second intervals and the «quadrant circle» on the SmartGuide display unit that it is time to move to the next quadrant of your mouth.

Please note: if the battery symbol is not displayed immediately, continue charging. It will appear in 10–15 minutes.

• When the rechargeable battery is low, the battery symbol with one remaining bar starts flashing. Your toothbrush will slow down and then stop. When the battery is fully discharged, the empty frame of the battery symbol flashes. It will then need a 15-minute charge before you can use it for a 2-minute brushing.

• For everyday use, the toothbrush handle can be stored on the charging unit to maintain it at full power. There is no risk of overcharging the battery.

Both timers memorize the elapsed brushing time, even when the handle is briefly switched off during brushing. Only when pausing longer than 30 sec. the timer resets to the initial starting point.

The «Count Up Timer» displays your actual brushing time. The «Count Down Timer» indicates the remaining brushing time. Starting with «2:00» minutes, it goes down to «0:00». When brushing longer than two minutes, it automatically changes to the «Count Up Timer».

Your toothbrush comes with the «Professional Timer» and the «Count Up Timer» activated. If you wish to change these settings, proceed as follows:

• Press and hold the mode button (c) until the SmartGuide display unit (k) shows «:30» and «timer».

• When pressing the on/off button your toothbrush automatically starts in the «Clean» mode.

3 sec.3 sec.

• By briefly pressing the on/off button (b), switch to the «2-Minute Timer». Confirm your choice by pushing the mode button (c).

• This will lead you directly to the «Count Up Timer» display («up» and «timer» will be shown). Switch to the «Count Down Timer» by pressing the on/off button and confirm it with the mode button.

Please note: it is normal that the handle display shows two flashing bars when operating in the timer setting mode.

• To switch to the other modes, successively press the mode button.

• To return from any mode to the «Clean» mode, press and hold the mode button.

• To turn your brush off, press the on/off button.

Please note: The «Polish» mode (deluxe model only) is best used with an Oral-B ProWhite brush head.

Brushing technique

• Guide the brush head slowly from tooth to tooth.

• Hold the brush head in place for a few seconds before moving on to the next tooth.

• Brush the gums as well as the teeth, first the outsides, then the insides, finally the chewing surfaces.

• Do not press too hard or scrub, simply let the brush do all the work. When you finish brushing, the total brushing time will be displayed for 30 seconds before the display switches back to the time mode. To directly get to the time mode, clear the brushing time display by pushing the mode button.

Brushing

Brushing modes

Your toothbrush offers different brushing modes for varying oral care needs:

«Clean» – Exceptional mouth cleaning. «Sensitive» – Gentle, yet thorough cleaning for sensitive areas. «Massage» – Gentle stimulation of gums. «Polish» (deluxe – Exceptional polishing model only) and natural whitening for occasional or everyday use.

Your toothbrush has a pressure control feature to help ensure that the right degree of pressure is applied. This helps protect your gums from excessive brushing and makes your toothbrush easy to operate. If too much pressure is applied, the oscillating movement of the brush head will continue but the pulsation will stop. In addition to feeling the change, you can also hear a different sound.

In the first days of using your toothbrush, your gums may bleed slightly. In general, bleeding should stop after a few days. Should it persist after 2 weeks, please consult your dentist or

dental hygienist. If you have sensitive teeth and gums, Oral-B recommends using the «Sensitive» mode.

Brushheads

The Oral-B FlossAction brush head (a) is recommended for everyday deep cleaning. It features micropulse bristles that get in hard-to-reach areas between your teeth, gently removing hidden plaque. For occasional or everyday whitening, please use the Oral-B ProWhite (j) brush head (not with all models). It features a dentist-inspired polishing cup to remove surface stains from coffee, tea and tobacco for effective brightening.

Please note that children under 12 years old should not use the Oral-B ProWhite brush head.

Do not use the Oral-B FlossAction or Oral-B ProWhite brush head with braces. We recommend using the Oral-B Ortho brush head, which is specifically designed to clean around braces and wires.

The FlossAction™ and ProWhite™ brush heads feature blue Indicator monitor brush head replacement need. With proper brushing, twice a day for two minutes, the blue color will fade halfway approximately within 3 months, signaling that it is time to change the brush head.

bristles helping you to

Too much pressure is applied. Reduce the brushing force.

«Quadrant circle» – currently you are brushing in the first 30-second interval. Move to the next quadrant of your mouth, when the second segment starts flashing.

Dentist recommended 2-minute brushing time has been reached.

The rechargeable battery of the handle is low. Charge the toothbrush handle.

Batteries of the SmartGuide display unit are low. Change batteries of the display unit.

Wall mount

If you prefer to mount the SmartGuide display unit on a wall, mirror or other surface, use the adhesive tape (m) to fix the wall mount. Before doing so, make sure the chosen surface is clean and dry (remove grease and dust first). Position the wall mount that the Oral-B logo is readable. Then press the wall mount evenly and firmly to the wall. Wait 24h before sliding the SmartGuide display unit into the fixed wall mount.

SmartGuide display unit

Displayed Icon

Meaning

«Clean» mode

«Sensitive» mode

«Massage» mode

«Polish» mode (not with all

models)

Please note: the adhesive tape will not work on dirt-repellent surfaces.

Cleaning recommendations

• After brushing, rinse your brush head thoroughly under running water.

• Remove the brush head from the handle and clean both parts separately under running

water. Then wipe them dry before you put the

set

h/min

3 sec.

set

h/min

3 sec.

handle on the charging unit.

• Before cleaning your charging unit, make sure you disassemble it first. The charging ring and the SmartPlug should never be placed in the dishwasher. However, all other parts (base station, base plate and protective cover) are dishwasher-safe.

dicating the «Learn» mode for synchronization is activated.

• Now you are requested by a flashing on/off button in the toothbrush icon on the SmartGuide display unit to turn the handle on. When doing so, the automatic synchronization process starts. It is finished when «L-1-» is displayed.

• Then turn off the handle.

If you would like to assign a second handle to the same SmartGuide display unit, repeat the last two steps described above with the other handle. You can exit the «Learn» mode by pressing the «h/min» or «set» button. Otherwise the «Learn» mode will automatically end after 30 seconds.

• From time to time, you can also clean the charging ring, the SmartPlug and the SmartGuide display unit with a damp cloth. The SmartPlug charger and the SmartGuide display unit should never be placed in water.

Synchronizing

In order to avoid interference of display messages when using more than one Oral-B Triumph toothbrush with separate SmartGuide display units in the same household, you need to assign the handles to their respective display units. Please follow the steps below:

• Push the «h/min» button in the battery compartment for at least 3 seconds. The SmartGuide display unit shows «L---», in-

Please note: –

A maximum of 2 handles can be synchronized with one SmartGuide display unit. After you synchronized the second handle, «Full» will be displayed.

– When changing batteries of the SmartGuide

display unit, stored data will be erased. Therefore, please repeat the synchronization process every time you change the batteries.

Deactivating the radio transmission

If you want to use or carry your toothbrush in surroundings where radio controlled appliances are not allowed (e.g. hospitals or aircraft), deactivate the radio transmission first by pressing the on/off (b) and mode button (c) for 3 seconds simultaneously. The handle display shows the radio deactivation icon. If you want

+ 21 hidden pages