Braun 8995 User Manual

8995

off

fix

trim

8995

www.braun.com/register

clean

eco

normal

auto select

intensive

cartridge

full

empty

Type 5646 Modèle 5646 Modelo 5646

5-646-453/01/II-06

English 4

Français 15

Español 25

Thank you for purchasing a Braun product. We hope you are completely satisfied with your new Braun shaver. If you have any questions, please call: US residents 1-800-BRAUN-11

1-800-272-8611

Canadian residents 1-800-387-6657

Merci d’avoir fait l’achat d’un produit Braun. Nous espérons que vous serez pleinement satisfaite de votre nouveau rasoir Braun. Si vous avez des questions, veuillez appeler Braun Canada : 1-800-387-6657

Gracias por haber comprado un producto Braun. Esperamos que Ud. quede completamente satisfecha con su nueva afeitadora Braun. Si Ud. tiene alguna duda, por favor llame al:

01(800) 508-5800

USA/CDN/MEX

8000

Series

8000

Series

360°Complete

start

clean

eco

normal

auto select

cartridge

intensive

full

empty

clea

ning

off

fix

trim

8995

English

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using this appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.

2. Do not use while bathing or in a shower when the appliance is connected to an electrical outlet.

3. Do not place, store or charge the appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

4. When not using for an extended period of time, unplug this appliance from the electrical outlet.

5. Unplug this appliance before cleaning.

6. This appliance comes provided with a special cord set with integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it.

FOR HOUSEHOLD USE SAVE THESE INSTRUCTIONS

WARNING

To reduce the risk of burns, ﬁre, electric shock, or injury to persons:

1. Close supervision is necessary when this appliance is used by, on, or near children or disabilities.

2. Use this appliance only for its intended use as described in this manual. Do not use attachments that are not recommended by the manufacturer.

3. The appliance should never be exposed to temperatures of less than 32 ºF / 0 ºC and more than 105 ºF/+40ºC for longer than a few hours. Be sure to completely dry appliance after use. Keep cord and adapter dry at all times. Do not store in a damp environment. To avoid damage do not wind the cord around the appliance. It is important to check the cord for damage periodically particularly at each end where the cord enters the plug.

4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

8. Do not use this appliance with a damaged or broken foil, as serious facial injuries may occur.

9. Always attach plug to appliance ﬁrst, then to outlet. To disconnect, turn all controls to «off», then remove plug from outlet.

Your 360° Complete (shaver with Clean&Renew™ station) is a system equipped with highly advanced electronic processors. It ensures unsurpassed closeness and comfort for you and optimum care for your shaver:

• The system automatically adapts to any voltage worldwide.

• The system recognizes when cleaning of your shaver is required, and automatically recognizes which of the three cleaning programs is appropriate.

• While the shaver is connected to an electrical outlet, the system automatically takes care of charging and discharging in a way that is optimized for the shaver’s battery capacity and life span.

• The system takes care of lubrication of the shaver’s cutting parts.

• The system tells you when to replace the shaving foil and cutter block.

Important

In order to avoid any leakage of the cleaning fluid, place the Clean&Renew™ station on a flat, stable surface. Do not tip, move suddenly or transport the station in any way if a cleaning cartridge is installed. Do not place the station in a mirror cabinet, store it over radiators, or place it on polished or laquered surfaces. Do not expose to direct sunlight. The station contains highly flammable liquid. Keep it away from sources of ignition. No smoking. Keep out of reach of children.

Do not refill cartridge. Use only original Braun refill cartridge.

Description

a n

e c

n o

in te

n s

ive

full

cartridge

to se

lect

p ty

c le

a n

e c

n siv

full

cartridge

auto selec

p ty

c l

e a

e c

n o

n s

iv e

full

cartridge

auto select

p ty

1 Special cord set 2 «start cleaning» button 3 Station-to-shaver connecting contacts 4 Station lift button for cartridge exchange 5 Display for cleaning programs 6 Display for cleaning fluid status 7 Station mains socket 8 Cleaning cartridge

9 Shaver foil protection cap 10 Shaver foil 11 Cutter block 12 Foil release buttons 13 Long hair trimmer 14 Shaver-to-station connecting contacts

(shaver backside) 15 Switch 16 Shaver display 17 Info key 18 Pilot light 19 Shaver mains socket

Before shaving

If you wish, you may start shaving right away (if the shaver is charged, see section «Shaver display»). However, we recommend to follow the procedure described here:

• Using the special cord set (1), connect the socket of the

Clean&Renew™ station (7) to an electrical outlet.

• Press the station lift button (4) to open the housing.

eco

normal

auto s

intensive

full

cartrid

empty

• Hold the cleaning cartridge (8) down on a flat, stable

surface (e.g. table).

• Carefully remove the lid from the cartridge.

• Slide the cartridge into the base of the station as far as

it will go.

• Slowly close the housing by pushing it down until it

locks.

trim

fix

off

cartridge

empty

The display for cleaning fluid (6) will show how much cleaning fluid is in the cartridge:

a) cleaning solution sufficiently available b) up to 7 cleanings left c) new cartridge required

full

empty

cartridge

full

empty

full

cartridge

trim

fix

off

auto select

clean

eco

norm

auto select

intensive

full

cartridge

empty

clean

eco

normal

intensive

a b

c d

Make sure the foil protection cap (9) is removed from the shaver. Insert the shaver head down into the station (the contacts (14) on the back of the shaver will correspond to the contacts (3) in the station). If necessary, the system will now charge the shaver. Also, the cleaning status will be automatically analyzed and one of the four diodes of the cleaning program display (5) will light up:

a) the shaver is clean b) eco(nomic), i.e. short cleaning required c) normal cleaning required d) intensive cleaning required

8995

clean

eco

normal

auto select

clean

eco

normal

to select au

intensive

full

cartridge

empty

intensive

If the system has selected one of the three cleaning programs, it will not start until you push down the «start cleaning» button (2). This locks the shaver into the station and starts the cleaning process.

We recommend cleaning after each shave.

While the cleaning is in progress, the respective cleaning program light will flash. Each cleaning consists of several cycles (where the cleaning fluid is flushed through the shaver head) and a heat drying period. The total cleaning time is 33 to 50 minutes.

Cleaning processes in the Clean&Renew™ should not be interrupted. While the shaver is drying, the metal parts of the shaver may be hot. Also, if the shaver is taken out prematurely and is not dry, its electronics could be harmed.

clean

eco

normal

auto select

intensive

When the program is finished, the blue «clean» light will shine. You can release the shaver by pushing the «start cleaning» button. Your shaver is now clean and ready for use.

Shaving

fix

trim

fix

8995

trim

f ix

off

If the shaver is locked into the Clean&Renew™ station, push the «start cleaning» button (2) to release the shaver and take it out.

Switch positions

off = (switch is locked)

Press and push up the switch to operate the shaver

on = Shaving with the pivoting head

(the pivoting cutting system automatically adjusts to every contour of your face).

fix = Shaving with the pivoting head locked at an angle

(to permit shaving in difficult areas, e.g. under the nose).

trim= The long hair trimmer is activated

(for trimming sideburns, moustache and beard).

Tips for the perfect shave

• Shave before washing your face or taking a shower, as skin tends swell after washing.

• The dryer the skin, the closer the shaving results will be.

• Hold the shaver at right angles (90°) to the skin. Stretch your skin and shave against the direction of beard growth.

• To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn.

Shaving with the cord

If the shaver is completely discharged and you do not have the time to recharge in the Clean&Renew™ station, you may also shave with the shaver connected to an electrical outlet via the special cord set.

After shaving

Automatic cleaning

After each shave, return the shaver to the Clean&Renew™ station and proceed as described above in the section «Before shaving». All charging and cleaning needs are then taken care of. With daily use, a cleaning cartridge should be sufficient for about 30 cleaning cycles. The hygienic cleaning solution cartridge contains alcohol which, once opened, will naturally evaporate slowly into the surrounding air. Each cartridge, if not used daily, should be replaced after approximately 8 weeks.

8995

n a le

l a rm

o n

to selec u a

e iv s

n te

ll fu

cartridge

t p m

fix

off

new

Quick cleaning

Press the foil release buttons (12) to lift the shaver foil (do not remove the foil completely). Switch on the shaver for approx. 5–10 seconds so that the shaved stubbles can fall out.

Thorough manual cleaning

Manual cleaning is recommended only when the Clean&Renew™ station is not available, e.g. when travelling. Never use water to clean the shaver. Remove the shaver foil and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. However, do not clean the shaver foil nor the cutter block with the brush as this may damage them. If you do not use the Clean&Renew™ station for a longer period of time, you should apply a drop of light machine oil onto the shaver foil.

Cleaning the housing

Clean the housing of shaver and station from time to time with a damp cloth, especially inside the opening of the station where the shaver rests.

Replacing the cartridge

After having pressed the lift button (4) to open the housing, wait for a few seconds before removing the used cartridge.

old

Before discarding the used cartridge, make sure to close the openings using the lid of the new cartridge, since the used cartridge will contain contaminated cleaning solution.

The shaver display

1. Pilot light: the shaver is connected to an electrical outlet.

8995

2. Shaver is charging / Remaining charging time.

3. Self testing / shaver is fully charged (a full charge will give up to 50 minutes of cordless shaving time, depending on your beard growth).

4. Remaining shaving time / Shaver must be charged.

8595

5. Time left in the cleaning process.

6. To maintain 100% shaving performance, replace your foil and cutter block, when the display shows «replace foil» (after about 18 months) or when the shaving parts are worn. Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil (10) and cutter block (11): 8000 series) The display will keep on reminding you during the next 7 days to replace the shaving parts. Then the shaver will automatically reset the display. After you have replaced the shaving parts (foil and cutter block) push the info key (17) 4 times until the display shows «reset foil?». Then push the info key for at least 3 seconds to reset the display. While doing so, the display blinks. When the reset is complete the display shows «reset ok». The manual reset can be done at any time.

7. System has initiated automatic battery maintenance (it is fully discharging and then recharging the batteries).

8. Environment temperature not suited for charging. Allow the shaver to remain for some time at room temperature for optimal charging conditions. Best environmental temperature range for charging is 60 °F to 95 °F / 15 °C to 35 °C.

9. Intensive cleaning needed – return to the Clean&Renew™ station as soon as possible. To reset the display, push the info key (17).

10. Display demo: hold the info key (17) for 3 seconds.

11. Info key, press once: duration of last shave. Press again: total number of shaves (cannot be reset). Press again: key part number for shaver foil and cutter block. Press again: foil reset? (can be resetted, see point 6).

12. No display – shaver is completely discharged.

+ 23 hidden pages