Bradley Corporation WF2503, WF2504, WF2803, WF2804 Installation Manual

Installation
Instructions

215-1415 Rev. J; EN 06-915B
© 2007 Bradley Corporation
Page 1 of 29 4/6/2007

P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . . . 2

Semi-Circular Washfountain Dimensions . . . . . 3-4

Rough-In Specifications . . . . . . . . . . . . . . . . . . . 5-8

Drain Rough-In Specifications . . . . . . . . . . . . . . . .9

Pedestal and Bowl Assembly and Mounting . . .10

Drain Spud Installation . . . . . . . . . . . . . . . . . . . . .11

Supplies w/Optional Soap Dispenser (A/O drains) . .12-13
Supplies w/Optional Soap Dispenser (B/H drains) . .14-15

Installing The Valve Assembly . . . . . . . . . . . . . . .16

Installing the Operating Rod . . . . . . . . . . . . . . . .17

Soap Recommendations and Maintenance . . . . . .18

Check Valve Troubleshooting . . . . . . . . . . . . . . .18

Soap Dispensing Valve Repair Parts . . . . . . . . . .19

Combination Check Valve Repair Parts . . . . . . . .20

Sprayhead Troubleshooting/Repair Parts . . . . . . 21

Foot Valve Breakdown and Repair Kit . . . . . . . .22

Manual Mixing Valve Repair Parts . . . . . . . . . . .23

Angle Volume Control Valve Repair Parts . . . . . .24

Vernatherm ™ Mixing Valve Maintenance . .25-27

Cleaning and Maintenance Instructions . . . . .28-29

WF2503

WF2804

IMPORTANT

Read this entire installation manual
to ensure proper installation.

Flush all the water supply lines
before making connections.

Main water supply to the unit
should be ON at all times.

This installation manual and parts
list should be filed by the owner’s
maintenance department.

WF2503, WF2504 Terreon®
WF2803, WF2804 Bradstone®

Pre-Assembled Classic
Semi-Circular 36"/54"
Washfountain with Foot
Control

UPC Certified

U

P

C

C

R

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

2 4/6/2007

Pre-Installation Information

Foot Control

Stepping on the foot rail allows the user to activate a valve starting the flow of water.

Supplies required for installation:

• (6) 1/2" lag bolts, screws or other fasteners to anchor washfountain pedestal to floor

• 1" hot and cold water supply lines and fittings (refer to rough-ins on pages 5-8)

• Reducing fittings and 1/2" nom. copper tubing supply lines for types with supplies from above

• 2" drain lines and fittings (refer to rough-ins on pages 5-8)

• Standard P-trap (refer to rough-ins on page 9, vented trap supplied for B and H type)

• Pipe sealant and plumber’s putty

• 1-1/2" vent pipe on types vented through washfountain column (refer to page 4 for lengths required)

• NOTE: Supply lines for one or two Washfountains should be 1"; for three Washfountains 1-1/4"; for
more than three Washfountains pipe size should increase proportionally. Vent pipe to be 1-1/2"
on models vented through Washfountain.

Bradley Classic Washfountain Warranty Information

Product warranties may be found under “Product Information” on our website at www

.bradleycorp.com

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

34/6/2007

Semi-Circular Washfountain Dimensions

ADJUST TO TOWEL DISPENSER
MOUNTING HOLES

A

B

C

D

F

E

G

6" (152)

H

K

J

*

Juvenile height: Subtract 4" from dimensions A through E for juvenile height.

(Bradstone not available in juvenile height)

*

Juvenile height: Subtract 102mm from dimensions A through E for juvenile height.

(Bradstone not available in juvenile height)

Material Size A B C D E F G H J K

Terreon® 54 19 29-1/2 38-3/4 47-1/4 36-1/2 55-3/4 23-1/2 21-1/4 32-1/4 5-1/4
Terreon® 36 19 29-1/2 35-1/4 43-1/4 33-3/8 52-1/4 17-1/4 15-1/4 22-3/4 4-3/4
Bradstone® 54 19-3/4 29-1/4 37-1/2 46 35-1/4 54-3/8 26-1/4 24-1/4 35-1/4 8-1/4
Bradstone® 36 19-3/4 29-1/4 34 42-1/2 35-1/4 50-7/8 20-1/4 18-1/4 25-3/4 7-3/4

Approximate Dimensions in Inches*

Material Size A B C D E F G H J K

Terreon® 1372 483 749 984 1200 927 1416 597 540 819 133
Terreon® 914 483 749 895 1099 848 1327 438 387 578 121
Bradstone® 1372 502 743 953 1168 895 1381 667 616 895 210
Bradstone® 914 502 743 864 1080 895 1292 514 464 654 197

Approximate Dimensions in Millimeters*

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

4 4/6/2007

Length of Tie Pipe Required for Vent Through Washfountain Column

54" Less Soap Dispenser 21-1/2" (546mm)
36" Less Soap Dispenser 18" (457mm)
54" With Soap Dispenser 30" (762mm)
36" With Soap Dispenser 26-1/2" (673mm)
54" Less Soap Dispenser With Towel Dispenser 55-1/2" (1410mm)
36" Less Soap Dispenser With Towel Dispenser 52" (1321mm)
54" With Soap Dispenser With Towel Dispenser 48" (1219mm)
36" With Soap Dispenser With Towel Dispenser 44-1/2" (1130mm)
54" With Cube Adaptor 32" (813mm)
36" With Cube Adaptor 28-1/2" (724mm)
54" With Cube Adaptor With Towel Dispenser 50" (1270mm)
36" With Cube Adaptor With Towel Dispenser 46-1/2" (1181mm)
54" With Cube Adaptor And Soap Dispenser 40" (1016mm)
36" With Cube Adaptor And Soap Dispenser 36-1/2" (927mm)

Type Pipe Length

NOTE: Drain must be connected with 2" schedule 40 welded wrought iron pipe, minimum, to provide

lower support for this installation. Vent or support pipe must be of the same material in 1-1/2".

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

54/6/2007

Rough-In Specifications

Type A

Off-Line Vent With Supplies From Below.

1" NPT Supplies
Through Wall

Cold

Trap

2" NPT Drain Through Wall

(Stub Out To Suit Trap Dimension)

Hot

Installing Traps

When installing trap with a coupling and
nipple, see dimension A in Table 1 on
page 9. If trap is installed tight to bottom
of bowl, dimension A depends on design of trap.
B* Wall to centerline of trap
A** Centerline of drain to floor

Drain Through Wall

Top View

Wall

B*

Trap For Wall
Outlet Only

2" NPT Drain Through Floor
(Stub Up 3" (76) Above Floor)

36" (914) Washfountain
Bowl

1" NPT Supplies Through Floor

3-1/4"

(83)

See Table 1
on page 9

(Optional) Stub Up 2-1/2" (64) Above Floor)

4" Centerline Of Drain To
(102) Centerline Of Fixture

54" (1372)
Washfountain
Bowl

7-5/8" (194)

4" (102)

Clearance Hole

Side View

A**

See Table 1
on page 9

Supplies Through Wall

Rough-In Notes:

1. All pipes and fittings not furnished by Bradley are shown in broken lines.

2. Supply lines for one to two washfountains should be 1"; for three washfountains 1-1/4"; for more
than three washfountains, pipe sizes should be increased proportionately.

3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.

4. Check valve inlets are 1/2" NPT.

5. Dimensions shown in parentheses are millimeters.

Wall

Floor

12" (305) For Standard Height
8-1/4" (210) For Juvenile Height

Drain & Supplies Through Floor
Trap Located Below Floor (Optional)

NOTE: UPC and IPC restrict the vertical
distance from the fixture outlet to the trap
weir to not more than 24". Check state and
local codes for variances.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

6 4/6/2007

Rough-In Specifications Continued . . .

1" NPT Supplies
From Above Must Reduce
To 1/2" Nom. Copper Tube
On These Centers To Pass
Thru Washfountain

Type O

Off-Line Vent With Supplies From Above

Top View

2" NPT Drain Through Wall

(Stub Out To Suit Trap Dimension)

4" Centerline Of Drain To
(102) Centerline Of Fixture

Trap For Wall Outlet Only

54" (1372)
Washfountain Bowl

Side View

Drain Through Wall

4" (102)

Clearance Hole

Floor

Drain & Supplies Through Floor
Trap Located Below Floor (Optional)

Wall

Wall

Rough-In Notes:

1. All pipes and fittings not furnished by Bradley are shown in broken lines.

2. Supply lines for one to two washfountains should be 1"; for three washfountains 1-1/4"; for more
than three washfountains, pipe sizes should be increased proportionately.

3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.

4. Check valve inlets are 1/2" NPT.

5. Dimensions shown in parentheses are millimeters.

2" NPT Drain Through Floor
(Optional) (Stub Up 3" (76) Above Floor)

7/8"

(22)

7/8"

(22)

1-1/4"

(32)

Cold

36" (914) Washfountain Bowl

Installing Traps

When installing trap with a coupling and
nipple, see dimension A in Table 1
on page 9. If trap is installed tight to bottom
of bowl, dimension A depends on design of trap.
B* Wall to centerline of trap
A** Centerline of drain to floor

B*

See Table 1
on page 9

See Table 1
on page 9

A**

Trap

Hot

NOTE: UPC and IPC restrict the vertical
distance from the fixture outlet to the trap
weir to not more than 24". Check state and
local codes for variances.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

74/6/2007

Rough-In Specifications Continued . . .

Type B

Centrally Rising Vent With Supplies From Above.

1" NPT Supplies
From Above Must Reduce
To 1/2” Nom. Copper Tube On
These Centers To Pass
Through Washfountain

Cold

Hot

(See Table on page 9)

(wall to centerline of trap)

7/8"

(22)

B*

7/8"

(22)

Top View

1-1/4"

(32)

1-1/2" NPT
Vent To Ceiling

36" (914) Washfountain

4"

(102)

2" NPT Drain (Make

Stub 3" (76)

Above Floor)

Bowl

54" (1372) Washfountain
Bowl

Vent

Side View

Wall

Floor

Drain Through Floor

Rough-In Notes:

1. All pipes and fittings not furnished by Bradley are shown in broken lines.

2. Supply lines for one to two washfountains should be 1"; for three washfountains 1-1/4"; for more
than three washfountains, pipe sizes should be increased proportionately.

3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.

4. Check valve inlets are 1/2" NPT.

5. Dimensions shown in parentheses are millimeters.

6. For maximum rigidity of sprayhead/support tube assembly, use 1-1/2" NPT galvanized pipe for vent.
Use of plastic or copper for vent is not recommended.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

8 4/6/2007

Rough-In Specifications Continued . . .

Type H

Centrally Rising Vent With Supplies From Below.

1" NPT Supplies
Through Wall

7-5/8"
(194)

7-5/8"
(194)

3-1/4"

(83)

B*

(See Table on page 9)

(wall to centerline of trap)

Vent

Top View

4"

(102)

12" (305 For

Standard Height

8-1/4" (210) For

Juvenile Height

1-1/2" NPT
Vent To Ceiling

Cold

Hot

2" NPT Drain (Make
Stub 3" (76) Above
Floor)

54" (1372)
Washfountain
Bowl

36" (914) Washfountain
Bowl

1" NPT Supplies
Through Floor
(Optional)
Stub Up 2-1/2" (63)
Above Floor)

Side View

Supplies Through Floor (Optional)

Rough-In Notes:

1. All pipes and fittings not furnished by Bradley are shown in broken lines.

2. Supply lines for one to two washfountains should be 1"; for three washfountains 1-1/4"; for more
than three washfountains, pipe sizes should be increased proportionately.

3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.

4. Check valve inlets are 1/2" NPT.

5. Dimensions shown in parentheses are millimeters.

6. For maximum rigidity of sprayhead/support tube assembly, use 1-1/2" NPT galvanized pipe for vent.
Use of plastic or copper for vent is not recommended.

Supplies

Through Wall

Wall

Floor

Drain Through Floor

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

94/6/2007

Installation Instructions

Step 1: Rough-In of Drain & Supplies

1. Rough in supply and drain piping as required for your installation (see pages 5-8 for rough-ins of
the optional installations).

2. Assemble the drain to the dimension shown in Figure 1 or Figure 2 and Table 1 for bowl size
you are installing.

NOTE: All piping shown in dotted lines to be supplied by the installer.

Compliance and conformity to local codes and ordinances is the r esponsibility of the installer.

Figure 1a

DRAIN (THROUGH

FLOOR - OPTIONAL)

T ypes A and O

Figure 2

VENTED TRAP

(111-024)

Types B and H

54"

Terreon®

6" (152) to 13-1/4" (336) 6" (152) to 10-1/4" (260) 5-1/4" (133) 18-5/8" (473) 14-5/8" (371)

36"

Terreon®

6" (152) to 13-1/4" (336) 6" (152) to 10-1/4" (260) 4-3/4" (121) 18-5/8" (473) 14-5/8" (371)

54" Bradstone* 6" (152) to 11-5/8" (295) N/A 8-1/4" (210) 17" (432) N/A
36" Bradstone* 6" (152) to 12" (305) N/A 7-3/4" (197) 17-3/8" (441) N/A

Bowl Material & Size

Std. Ht. Juv. Ht. Std. Ht. Juv. Ht.

ABC

* Bradstone is not available in juvenile height.

Table 1 — Trap Dimensions (mm)

Figure 1b

TIE PIPE BRACKET

- OPTIONAL

T ypes A and O

A

B

C

C

9-3/4"

(248)

B

B

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

10 4/6/2007

Installation Instructions continued . . .

Step 2: Pedestal and bowl assembly and mounting

NOTE: (Terreon only) It will require more than one person to turn the bowl/pedestal assembly
upright. (It is shipped with the bowl on the bottom).

1. Position the bowl and pedestal assembly so that the bowl drain is in line with trap or drain line.

2. Drop the spud into the drain to insure correct alignment (See Figure 4 on Page 11).

3. Level the bowl, if required, by placing washers under the legs. Check fit against the wall and
adjust if necessary by loosening the screws attaching the bowl to the pedestal.

4. Anchor the pedestal to the floor with suitable fasteners (supplied by installer). See Figure 3 and
Table 2.

NOTE: The pedestal must be level when secured to floor for proper drainage.

CAUTION: BOWL SURFACE IS SMOOTH. USE SUITABLE LIFTING EQUIPMENT

TO POSITION THE BOWL AND PEDESTAL ASSEMBLY. HANDLE WITH
CARE!

Figure 3

Table 2 — Pedestal Anchoring Dimensions (mm)

36" Terreon 11" (279) 8-5/8" (219) 18-1/4" (464) 14-1/4" (362)
54" Terreon 16-1/2" (419) 14-1/8" (359) 18-1/4" (464) 14-1/4" (362)
36" Bradstone*

—

8-5/8" (219)

— N/A

54" Bradstone*

—

14-1/8" (359)

— N/A

Bowl Material & Size

Std. Ht. Juv. Ht.

AB C

* Bradstone is not available in juvenile height.

A

A

C

B

B

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

114/6/2007

Installation Instructions continued . . .

Step 3: Installing drain spud in bowl

NOTE: Seal between drain spud and drain hole with plumber’s putty (supplied by installer).

1. Secure the drain spud with the lock nut and washers as shown in Figure 4.

Figure 4

STRAINER
S45-067

GASKET
125-011

SPUD
112-015

BOWL

WASHER
142-068

LOCKNUT
161-021

DRAIN PRE-PACK

S45-273

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

12 4/6/2007

Installation Instructions continued . . .

Step 4a: Installing Supplies with Optional Soap Dispenser for A/O drain units

NOTE: See Step 4b for units with type B/H drain.
NOTE: For models with optional paper towel dispensers, tie pipe assembly, or shroud, see separate

instruction sheets and Step 4b for units with type B/H drain.

NOTE: Flush the supply lines before making connections.

1. Install the hemmed end (not sharp end) of the support tube (welded seam toward the wall) with the gasket
into the bowl.

2. Using pipe sealant, connect the supply pipe to the sprayhead and place on top of the support tube as
shown in Figure 5 on Page 13. Make sure spray holes point away from the wall.

3a

. For Unit with Soap Option:

1. Place the upper tie bar (notched at corners) on top of the sprayhead and join the upper and lower tie rod
(the longer threaded rod) with the coupling nut and setscrews. Upper tie bar must be parallel to wall.

2. Insert the tie rod assembly through the hole in the upper tie bar and secure with the lower tie bar, tie rod
nut and setscrew from below (see Figure 5).

3. Install the spacer, soap dispenser, dispenser cover and restraining bracket and secure with the acorn nut
and socket setscrew. The tab on the restraining bracket should fit in a notch in the dispenser cover. See
Figure 5.

4. Continue installation with Step 5 on Page 16.

3b

. For Unit without Soap Option:

1. Place the dispenser cover on the sprayhead. Thread the acorn nut onto the lower tie rod, run the tie rod
through the dispenser cover and restraining bracket and secure from below with the lower tie bar, tie rod
nut and socket setscrew (see Figure 5). The tab on the restraining bracket should fit in a notch in the dis­penser cover.

2. Continue installation with Step 5 on Page 16.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

134/6/2007

Installation Instructions continued . . .

Figure 5

TYPE "O" DRAIN

(Supplies from above)

Acorn Nut (110-052A)
& Set Screw (160-093)

Dispenser Cover

Soap

Dispenser

Upper Tie Bar

(159-009A)

(notched at corners)

Support Tube

(S57-005, 54")
(S57-006, 36")

Sprayhead Supply

Pipe (3/8")

Gasket

(125-011)

TYPE "A" DRAIN

Restraining
Bracket

Tab fits into dispenser cover

Soap Dispenser Lid

Upper Tie Rod

(176-010)

Spacer

(113-155A)

Coupling Nut (110-051D)
Set Screws (160-208)

Sprayhead

(S05-054B)

Lower Tie Rod

(176-008, 36")
(176-008A, 54")

Lower Tie Bar

(159-009)

PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.

(See Figure 7 on page 16 for valving assembly)

HOT

Tie Rod Nut

(110-064)

& Set Screws

(160-208)

Operating Rod

(S14-007, Std. Ht.)
(S14-007A, Juv. Ht.)

COLD

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

14 4/6/2007

Installation Instructions continued . . .

Step 4b: Installing Supplies with Optional Soap Dispenser for B/H drain units

1. Install the hemmed end (not sharp end) of the support tube (welded seam toward wall) with gasket into
the bowl (see Figure 6 on page 15 for type B or type H).

2. Using pipe sealant, connect the supply pipe to the sprayhead and place on top of the support tube.
Run tubing down through the support tube. Make sure spray holes point away from the wall.

3. Insert the 1-1/2" vent pipe (supplied by installer, see page 4 for length) through the soap
dispenser with the spacer (if provided), sprayhead, and support tube.

4. Connect to the vented trap (provided).

5a. For Unit with Soap Option:

1. Slide the tie bar over the 1-1/2" vent pipe 1/2" below the top of the soap dispenser and secure
with the set screws. (Tie bar must be parallel to wall).

2. Slide the dispenser cover over the 1-1/2" vent pipe and secure with the two screws (included) to
the tie bar.

5b

. For Unit without Soap Option:

1. Slide the tie bar over the 1-1/2" vent pipe, 1/2" below the top of the sprayhead and secure with
the set screws. (Tie bar must be parallel to wall).

2. Secure the dispenser cover over the 1-1/2" vent pipe and secure with the two screws included
with the tie bar.

6. Connect the Vent Pipe

a. Connect the vent pipe to the vent through the ceiling with the pipe union.
b. Continue installation with Step 5 on Page 16.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

154/6/2007

Installation Instructions continued . . .

Figure 6

TYPE "H" DRAIN

(Supplies from below)

TYPE "B" DRAIN

Cap Screw

(160-108)

Dispenser Cover

1-1/2" Vent Pipe

Soap

Dispenser

Support Tube

(S57-005, 54")
(S57-006, 36")

Sprayhead Supply

Pipe (3/8")

Gasket

(125-011)

HOT COLD

Supplies 1/2" Nom.
Copper Tubing

Tie Bar Location
For Unit With Soap

(159-020)

Soap Dispenser Lid

Spacer

(113-155A)

Tie Bar Loation For
Unit Without Soap (159-020)

Sprayhead

(S05-054B)

PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.

(See Figure 7 on page 16

for valving assembly)

Vented Trap

(111-024)

Operating Rod

(S14-007, Std. Ht.)
(S14-007A, Juv. Ht.)

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

16 4/6/2007

Installation Instructions continued . . .

Step 5: Installing the Valve Assembly

NOTE: Flush supply lines before making connections.

1. For overhead supply lines, install 1/2"nominal copper supply tubing by passing the lines through
the holes in the dispenser cover and then down through the support tube.

2. Install the valving assembly using suitable fittings to the supplies as shown in Figure 7 at the
approximate height indicated in Table 3.

3. Slide the tailpiece nut over the tailpiece and connect the tailpiece to the supply pipe (or to the
nipple/coupling for B or H drain).

Figure 7

Model Number Type A Type B Type O Type H

Standard Height 9" (229mm) 6-3/16" (157mm) 9" (229mm) 6-3/16" (157mm)
Juvenile Height 5-1/4" (133mm) 3-7/16" (87mm) 5-1/4" (133mm) 3-7/16" (87mm)

Table 3 — Distance from 1/2" Supply to Finished Floor

Stop-Strainer-Check

Valve

(S60-003)

Tailpiece

(129-007)

To Supply Pipe

Tailpiece

(129-009)

(110-005)

Foot Valve

(S07-066)

Nut

(110-005)

Nut

Washer

(124-001AF)

Coupling

(169-174)

Nipple

STD: 2" Long (113-852)
JUV: Close (113-006AL)

Tailpiece Washer

(124-001AF)

Operating Lever

Used on "B"
and "H" models only

Manual Mixing

Valve

OPTIONAL Vernatherm™

Thermostatic

Mixing Valve

(S01-525)

(Units are supplied with
Manual Mixing Valve as

standard equipment)

(S01-038)

V alve Assembly

Distance (dimension)

finished floor - see

Table 3

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

174/6/2007

Installation Instructions continued . . .

Figure 9

Figure 8

Step 6: Installing the Operating Rod

1. Insert the operating rod in the operating rod lever and then into the foot lever (see Figure 8).

NOTE: For normal operation, use the operating rod as shipped. The spring loaded cartridge should
be adjusted so there is no play in the operating lever. Care must be taken to insure that a snug fit is
achieved without activating the foot valve or water will leak from the sprayhead (see Figure 8).

2. When movement of the operating rod is insufficient to open the foot valve, disassemble the rod
and remove the spacer and override spring. Reassemble the operating rod as shown in Figure 9.
Reinstall and adjust so that the foot valve is completely open when the foot lever is fully
depressed. This prevents damage to the foot valve due to the absence of the override spring.

3. Turn supplies on and activate the sprayhead. Check piping installation for leaks.

4. Clean the sprayhead if necessary. See page 21 for sprayhead troubleshooting. Adjust the volume
control valve, if necessary, to control the flow of water.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

18 4/6/2007

Soap Recommendations and Maintenance Tips

Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley
soap dispensers will provide dependable, consistent operation over the long term when soap with reasonable
viscosity and pH levels are used and when a minimal amount of periodic maintenance is performed on the
valves.

Soap thickness is determined by a measurement called viscosity. Soap viscosity should be between 100 cps
(centerpoise) and 2500 cps for all Bradley soap dispensers. Thinner soaps are perceived by the users as being
“watered down” so users tend to take more than they need, resulting in waste. Thick soaps flow slower and

inhibit the “flushing” action of the valves, which allows the soap to congeal in the valve and cause clogs.

The pH (acid) level of the soap should be in the range of 6.5 to 8.5. More acidic soaps (pH levels lower
than 6.5) will corrode metal parts (even stainless steel!!) and degrade rubber and plastic components.
They will also cause skin irritation. Most inexpensive soaps (typically the pink lotion type) fall into this
acidic category and will eventually cause valve failure and metal corrosion. Base soaps (pH levels higher
than 8.5) will cause swelling or degradation of rubber and plastic parts and skin irritation.

Generally, any quality soap meeting the viscosity and pH guidelines above will work well with Bradley
soap dispensers. PCMX or Isapropanol based antibacterial soaps (within viscosity and pH limits) will also
work with Bradley dispensers. Soaps satisfying these basic guidelines will provide consistent flow and
reduce clogs.

Most soap dispenser problems are caused by soap that is too thick or corrosive, or by a lack of maintenance.
Many soaps come in concentrate form which must be diluted with water. Often, the soap is improperly
diluted or used straight out of the bottle, which causes clogging and valve failure. If proper soap is being
used, valves that have never been cleaned are usually the source of dispensing problems. Bradley has
entered into an agreement with Champion Brand Products to provide additional customer service for
purchasers of our dispensers regarding soap issues. They are very helpful and can get to the bottom of
almost any soap dispenser-related problem. They also sell an excellent “Bradley approved” soap. Please
see Bradley Instruction sheet 215-1286 for soap valve cleaning details and Champion Brand Products
contact information.

Check Valve Troubleshooting

If water just dribbles or does not flow from sprayhead:

1. Turn off water supplies to fixture.
2 Inspect check valves for proper installation. See Stop, Strainer and Check Valve on page 19.

3. Open the stops and clean the strainers, if necessary.

If water sprayhead delivers all hot or cold water:

1. Turn off water supplies to fixture.

2. Inspect check valves for proper installation.

3. Open the stops and clean the strainers, if necessary.

4. Inspect mixing valve for proper installation (see Vernatherm Thermostatic Mixing valve on page 24)

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

194/6/2007

Soap Valve - Liquid - S09-007S

This valve delivers a measured
amount of soap with each
upward stroke. The soap dis­penser has been standard on
washfountains since 1983 and
is not well-suited for very thick
lotion soaps.

NOTE: Lotion soap will clog
liquid soap valves. Use only
lotion soap valves with lotion
soap.

Soap Valve - Lotion - S09-057S

Soap Valve - Powdered - S09-010A

NOTE: Reducer plugs are available for use with fine granulated soap to
reduce the flow.

NOTE: Valves can be changed from powdered to liquid by plugging the
innermost, or “bearing” hole with rubber plug, part number 125-001AK.
To change from liquid to powdered, the plug must be removed. If none is
present, it will be necessary to drill out the bearing hole with a 1/2" or
5/8" drill. The plastic container configuration forms a natural template
for locating the bearing hole.

1 118-025 Valve Body 1
2 110-007 Packing Nut 1
3 135-001L Spring 1
4 125-001BU Washer 1
5 119-028 Plunger 1

* 161-014 Nut 1
* 124-001D Washer 2
* 142-002AH Washer - Stainless Steel 1

Attaching

Parts

S09-007S

Item Part No. Description Qty

Parts List

* Not Illustrated

1 124-001D Washer — 1
2 110-057 Nut — 1
3 125-001AN Stopper — 1
4 159-114 Reinforcing Plate — 1
5 124-001AT Washer — 1
6 160-176 Screw — 1
7 S09-040 Valve 1 1
8 S53-045 Adaptor 1 1

Valve Attaching

Assembly Parts

S09-057 S09-057S

Item Part No. Description Qty

Parts List

1 160-069 1 Screw, 1/4-20 RD
2 142-002X 1 Washer, 1/4 Split-Lock
3 S62-002 1 Agitator / Slide Assy.
4 192-004 1 Lever - Powdered Soap

Item Part No. Qty Description

Parts List

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

20 4/6/2007

Stop, Strainer and Check Valve

1/2" NPT

Strainer

Check

Stop

1/2" NPT

6

8

2

3

4

5

7

9

10

6

5

11

1

2

3

4

1

1 118-039 1 Valve Body - Brass
1 118-039A 1 Valve Body - Plated
2 160-131 1 Set Screw
3 S21-014 1 Stop Assembly - Celcon

3 S21-026 1 Stop Assembly - Brass
*4 156-006 1 Strainer
*5 124-001BV 2 Fiber Washer
*6 153-068 2 Plug - Brass

7 129-007 1 Tail Piece - Brass

7 129-007A 1 Tail Piece - Plated

8 110-005 1 Tail Piece Nut - Brass

8 110-005A 1 Tail Piece Nut - Plated
*9 124-001AF 1 Tail Piece Washer

*10 135-001AB 1 Spring
*11 S21-015 1 Check Assembly

Item Part No. Qty Description

Parts List

S60-003 Stop, Strainer and Check Valve

1 119-057 1 Valve Core
*2 125-001AW 1 “O” Ring
*3 125-001L 1 Bibb Washer

4 160-164 1 Screw

Item Part No. Qty Description

Parts List Stop Assembly S21-014

Standard Celcon Core

1 119-091 1 Plunger

2 125-001BB 1 Washer

Item Part No. Qty Description

Parts List Check Assembly S21-015*

1

2

* S45-050 Repair Kit Includes these parts

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

214/6/2007

Sprayhead Troubleshooting and Repair Parts

Problem: Water splashes over the rim of the bowl.

Cause: Foreign matter has reduced the size of the sprayhead slots, causing greater pressure at the

open slots.

Solution: Clean the sprayhead:

1. Disassemble the sprayhead and dislodge any dirt, lime build-up and foreign debris with a wire
brush.

2. Sprayheads with rubber grommet spray rings may be cleaned by rubbing a coin over the grommet.

3. Throttle down the volume control (water spray should strike the bowl without splashing outside
of the bowl).

Problem: Water flow diminishes from the sprayhead.

Cause: Strainer portion of the stop-strainer-check valve is plugged.

Solution: Remove and clean the strainer screen from the stop-strainer-check valve.

NOTE: The sprayhead shown below includes a perforated rubber spray ring grommet that is self­cleaning. The water pressure flexes the spray holes which slows accumulation of foreign matter and
tends to “break loose” any such deposits that may have accumulated.

1 125-001DE Neoprene Washer-Top 1 1
2 139-031 Sprayhead Manifold 1 —
3 124-001AL Washer 3 4
4 160-211 Carriage Bolt 3 4
5 115-061 Sprayhead Top 1 —
6 116-008 Sprayhead Bottom 1 —
7 124-001AT Washer 3 4
8 161-025 Nut 3 4
9 124-020D Sprayhead Grommet - Semi-circle 1 —

10 125-001DF Neoprene Washer-Bottom 1 1

Sprayhead Assembly Repair Kit

S05-054B S45-051

Item Part No. Description Qty

Parts List

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

22 4/6/2007

Repair Parts continued . . .

S65-230 — Repair Kit for Foot Valve S07-066

1 1 118-302 FOOT VALVE BODY
2 1 125-154 O-RING, #2-127
3 1 118-300 HOUSING
4 1 135-088 SPRING
5 1 117-016 VALVE SEAT
6 1 S64-093 PLUNGER ASSEMBLY
7 1 125-001Y DIAPHRAGM
8 1 179-002 PLUNGER GUIDE

9 1 119-024 PLUNGER
10 1 143-026 OPERATING LEVER
11 1 110-101 BOTTOM NUT
12 1 124-001V WASHER, 1-3/8" x 5/8"

ITEM QTY. PART NO. DESCRIPTION

S07-066 Foot Valve

1 1 118-300 HOUSING

2 1 135-088 SPRING

3 1 125-154 O-RING, #2-127

4 1 S64-093 PLUNGER ASSEMBLY

5 1 117-016 VALVE SEAT

6 1 125-001Y DIAPHRAGM

7 1 124-001V WASHER, 1-3/8" x 5/8"

8 1 130-033 KEY, VALVE SEAT

9 1 S45-125 LUBRICANT (not shown)

ITEM QTY. PART NO. DESCRIPTION

S65-230 Foot Valve Repair Kit

6

7

5

4

3

2

1

8

10

12

11

9

8

1

2

3

4

5

6

7

NOTE: This repair kit services only the S07-066 valve shipped AFTER January 2003.
See 215-1370 Washfountain Parts and Service Guide for service information before this date.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

234/6/2007

Manual Mixing Valve Repair Parts

1 118-034 Mixing Valve Body - Brass 1 1 —
1 118-034A Mixing Valve Body - Chrome — — —
2 124-001BD Fiber Washer 1 1 1
3 125-001BC O-Ring 1 1 1
4 119-059 Mixing Valve Core 1 1 1
5 152-038 Roll Pin 1 1 1
6 121-016 Bonnet - Brass 1 1 1
6 121-016A Bonnet - Chrome — — —
7 160-197 Screw - Brass 1 1 —
7 160-189 Screw - Stainless Steel — — —
* 129-007 Tailpiece - Brass — 2 —
* 110-005 Tailpiece Nut - Brass — 2 —
* 129-007A Tailpiece - Chrome — — —
* 110-005A Tailpiece Nut - Chrome — — —
* 124-001AF Tailpiece Washer — 2 2

Valve Valve and

Assembly Tailpieces Repair Kit

S01-038 S01-038S S45-197

Item Part No. Description Qty

Manual Mixing Valve Parts List

* Parts not shown

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

24 4/6/2007

Volume Control Valve Repair Parts

1 125-001BC O-Ring 1 1
2 152-038 Roll Pin 1 1
3 121-016 Bonnet 1 1
3 121-016A Bonnet — —
4 124-001BD Fiber Washer 1 1
5 119-060 Valve Core 1 1
6 118-033 Valve Body 1 —
6 118-033B Valve Body — —

Brass

Valve Repair Kit

S02-045 S45-198

Item Part No. Description Qty

Volume Control Valve Parts List

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

254/6/2007

Adjusting the Vernatherm Thermostatic Mixing Valve

NOTE: This valve is NOT factory preset. Upon installation, the temperature of this valve must be
checked and adjusted to ensure delivery of a safe water temperature. Water in excess of 110°F
(43°C) may cause scalding.

1. Check the temperature when approximately 1.0 GPM water flow is reached and adjust if neces­sary (the range of the valve is 95°F–115°F (35°C–43°C). To adjust the temperature, follow the
procedure below:

• Loosen temperature locking nut with wrench.

• Using a blade screwdriver, turn the adjustment stem counterclockwise to increase the temper-

ature or clockwise to decrease the temperature (Figure 10).

• Once desired temperature has been reached, tighten lock nut to prevent change in temperature.

2. Shut the hot water inlet off by closing the hot water stop-strainer-check valve. While the hot
water supply is turned off, check to make sure the cold water flow is reduced. If the cold water
is reduced properly, reopen the hot water supply.

3. Shut the cold water inlet off by closing the cold water stop-strainer-check valve. While the cold
water supply is off, check to make sure that the hot water flow has shut down.

TEMPERATURE

ADJUSTMENT

STEM

TEMPERATURE

LOCKING

NUT

Figure 10

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

26 4/6/2007

Thermostatic Mixing Valve Maintenance and Troubleshooting

NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the
following conditions:

• If stop/check valves are used, make sure that they are fully open

• Make sure that the hot and cold inlet pipes are connected properly, and that there are no
cross-connections or leaking stop/check valves

• check the hot water heater output to make sure that it is at least 20° F above the set temperature.

Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the
valves after inspection and repair is complete.

Problem: Limited water flow

Cause: Dirt and debris have built up in the valve.

Solution: Check the valve's piston for free and smooth movement, follow the procedures outlined

below:

1. Remove the valve's cap and thermostat (see Figure 11 on Page 27).

2. Push down on the piston with your finger (the piston should move freely). If the movement is
not as it should be, the piston needs to be cleaned. Follow the method outlined below for
cleaning the piston and valve body:

• Remove the thermostat.

• Lift the piston out with a needle-nose pliers and remove the spring.

• Any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable

cleaner is not sufficient to remove debris, a 400-grit sandpaper may be used to polish and
hone the piston and valve body).

• Snap spring into piston (will detent) and reassemble into the valve body.

• Retest the piston.

3. If, after a thorough cleaning, the piston does not move freely, the piston must be replaced.
Contact your Bradley representative and ask for Repair Kit (part number S65-259).

Problem: External leaks in the system

Cause: O-rings have been damaged.

Solution: Replace O-rings where necessary. For replacement of the O-rings, contact your

Bradley representative and ask for Repair Kit (part number S65-259).

Problem: Improper water temperature or temperature fluctuation

Cause: Thermostat is slowly failing or not working at all.

Solution: "Check the thermostat for proper operation".

1. At room temperature (80° F or less) remove cap and thermostat.

2. Place thermostat into container with 115° F water. The pushrod should pop out of the
thermostat approximately 1/10".

3. If thermostat pushrod does not pop out, the thermostat must be replaced. Contact your
Bradley representative and ask for Repair Kit (part number S65-259).

Cause: Valve temperature is not properly set.

Solution: "Adjust the temperature" per steps on Page 25.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

274/6/2007

9

6

5

4

3

2

7

8

Spring

Thermostat

Piston

Stem

O-Ring

O-Ring

Cap

Nut 3/8-24 Hex Jam

10

Seal Cup

1

Valve Body

Vernatherm Thermostatic Mixing Valve (S01-525) Parts List — Repair Kit S65-259

Figure 11

5 S39-413 1 Thermostat
7 125-001BX 1 O-Ring
8 125-157 1 O-Ring

Item Part No. Qty Description

Parts List

S65-259 Valve Repair Kit

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control
WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone® Installation Instructions

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

28 4/6/2007

Cleaning and Maintenance Instructions for Terreon®

Material Description: Terreon® is a NAHB Certified densified solid surface material composed of polyester
resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with every­day cleansers or fine grit abrasives.

Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household
cleaner such as Formula 409

®

or Windex®.

Stubborn Stains: Remove tough stains with Ajax

®

, Comet®, or Soft-Scrub®and a green Scotch-Brite®pad or
lightly sand in a circular motion with 240 grit wet/dry sandpaper. The finish can be renewed with a maroon
Scotch-Brite pad.

Special Situations for Material

Scratches: Remove scratches with a green Scotch-Brite®pad. The finish can then be renewed with a maroon
Scotch-Brite

®

pad.

Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse
the unit thoroughly after cleaning.

Restoring the surface: Use Hope's

®

Solid Surface cleaner and polish to refresh and protect the Terreon
Solid Surface material.Bradley recommends additional care and maintenance for the darker colored Terreon,
for complete instructions on this additional maintenance see Bradley document #1505.

IMPORTANT:

DO NOT USE STRONG ACID OR ALKALINE CHEMICALS AND CLEANSERS TO
CLEAN TERREON. IF THESES CHEMICALS COME IN CONTACT WITH THE TERREON SUR­FACE WIPE THEM OFF IMMEDIATELY AND RINSE WITH SOAPY WATER.

AVOID CONTACT WITH HARSH CHEMICALS SUCH AS PAINT REMOVER, BLEACH, ACETONE,
ETC. AVOID CONTACT WITH HOT PANS AND OBJECTS.

Repair Kits: Terreon®repair kits are available. Contact your Bradley representative or distributor for part num-
bers and pricing.

NOTE: Repair kits are made to order and have a shelf life of 30 days.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, or does the omission of any brand name cleaner imply it’s inadequacy. Many products named are
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through
your cleaning service. It is emphasized that all products should be used in strict accordance with package
instructions.

Cleaning and Maintenance Instructions for Bradstone

Bradstone is impervious to most chemicals and stains. Soap and dirt accumulations should be washed off
with detergent cleaners. Abrasives and caustic cleaners are not recommended. An occasional waxing with
automotive wax will make future cleaning even easier.

Pre-Assembled Classic Semi-Circular 36"/54" Washfountain with Foot Control

Installation Instructions WF2503, WF2504 Terreon® — WF2803, WF2804 Bradstone®

Bradley Corporation • 215-1415 Rev. J; EN 06-915B

294/6/2007

Cleaning and Maintenance Instructions for Stainless Steel

Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive.
Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and
work your way toward the more complicated.

Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia.
Apply the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid
damaging the finish.

Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball

®

stainless steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same
direction as the polish lines.

IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON STAINLESS
STEEL. ALWAYS USE STAINLESS STEEL WOOL OR STAINLESS STEEL BRUSHES.

Special Situations for Material

Finger Prints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and
polish in accordance with the manufactures instructions. Many of these products leave a protective coating
the helps prevent future smears and fingerprints.

Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufactures instructions and in the direction of the polish lines.

Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thio­cyanates (pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment,
especially if acid conditions exist.

IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON
STAINLESS STEEL.

The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the
actual source of the rust in some iron or steel particles which may be touching, but not actually a part of the
stainless steel structure.

NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of
these cleaners should be avoided.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your
cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.

Drain Cleaning

Drains can be cleaned with a plumbers snake inserted through the drain spud after removing the
strainer, or through the trap clean out plug

IMPORTANT: Do not put drain cleaners in bowl. Damage to bowl will result.