BOXLIGHT ProjectoWrite6, ProjectoWrite5 User Manual

ProjectoWrite6

User Manual

151 NE State Hwy 300, Ste A

Belfair, WA 98528

360.464.2119

www.boxlight.com

Projector

About the Owner’s Manual

Please read the owner‟s manual thoroughly to ensure correct use of the projector and its
features.
After reading, store the owner‟s manual in a safe place for future reference.

Features

1. Short throw

2. Designed for tough environments

3. Side changLQJ lamp

4. Side changLQJ filter

5. Advanced anti-theft features

6. Five auto features (Auto Search, Auto Sync, Auto Ceiling, Auto Keystone and Auto
Filter

Alert)

7. Seven display modes (Natural, Cinema, Daylight, Green board, White Board, Black
Board and User)

8. Built-in 10W speaker

9. Logo capture

10. Image freeze function

11. LAN Control

12. LAN Display

13. USB Display

14. PC-less presentation (Photo, Video, Audio and Microsoft Office Viewer)

15. 1.5G% free internal storage for multi-media display

16. WiFi Display (Option)

The content of this manual is subject to change without previous notice.
All rights reserved.

Contents

1

About Owner’s Manual

Contents......................................................................................................................1

Contents of Your Box.................................................................................................3

Safety Instructions.....................................................................................................4

Safety Labels..............................................................................................................5

Part Names.................................................................................................................7

Projector.......................................................................................................................................................7

Touch Keypad............................................................................................................................................8

Rear.............................................................................................................................................................9

Setting Up.................................................................................................................10

Arrangement...........................................................................................................................................10

Power ON / OFF......................................................................................... .............................................11

Setting Up The Projector.................................. ........................................................... ...........................12

Ceiling Mounted Installation Guide......................................................................................................13

Adjusting The Projector’s Elevation.....................................................................................................14

How To Connect......................................................................................................................................15

Remote Control........................................................................................................17

EZ Suite……….……………………………………………………………………19

Main Menu Layout & Function Definition……………………………………....19

EZ Media Function: Layout & Behavior………………………………….......…20

Photo Function…………………………………………………………………............................……21

Video Function………………………………………………………………………............................23

Audio Function………………………………………………………………………...........................24

Office Viewer Function………………………………………………………………..........................26

EZ Display Function: Layout & Behavior……………………………………….28

EZ USB…..………………………………………………………………..............................………...29

EZ WiFi………………………………………………………………………………..........................30

EZ LAN………..……………………………………………………………………............................44

Setting & Configuration……………………………………….………………….46

System Setting………………………………………………………...............................……………46

Video Setting………………………………………………………………………….........................47

Photo Setting……………………………………............................………………………………....48

Audio Setting………………………………………………………………………..........................…48

W

iFi

Setting…..…………………………………………………………………..... . . .............……49

Connect PC Setting…………………………………….................................…………………………..57

Menu Operation.......................................................................................................58

How To Operate On-Screen Display.................................................................................................. .5 8

Contents

2

MENU (PC Mode)...................................................................................................59

Picture Menu (PC Mode)..........................................................................................................................59

Audio Menu (PC Mode)............................................................................................................................60

Setting Menu (PC Mode)..........................................................................................................................61

Picture Menu (Video Mode)......................................................................................................................62

Audio Menu (Video Mode)........................................................................................................................63

Setting Menu (Video Mode)......................................................................................................................64

Advanced Menu.........................................................................................................................................65

Presentation Menu.....................................................................................................................................69

Security Menu............................................................................................................................................71

PIN Key In Operation.............................................................................................75

Network Control Software Application ………………….....................................76

Browser Control.........................................................................................................................................77

Home(Status)..............................................................................................................................................78

Control Panel..............................................................................................................................................79

Network ......................................................................................................................................................81

Alert ............................................................................................................................................................82

Schedule......................................................................................................................................................83

Time ……………………………..................................………………………………………………......84

Creston ………………………..………………………………………………….................................…84

About the Tools button..............................................................................................................................85

About the "Info" button ……………………………............................…………………….………......87

About the "Contact IT Help" button …………………………………………..................................…87

Logout…………………………………………………........................................……………………….87

Maintenance Of Projector.......................................................................................88

Filter / Replacing the Air Filter…………................................................................................................ 88

Lamp / Replacing New Lamp...................................................................................................................89

Other Care..................................................................................................................................................91

Troubleshooting........................................................................................................92

I

ndicator.....................................................................................................................................................92

Error for Machine Defects........................................................................................................................93

List of Supported Monitor Displays.........................................................................................................95

Appendix...................................................................................................................96

Menu Tree(PC Mode)................................................................................................................................96

Menu Tree(Video Mode)............................................................................................................................97

Appearance.................................................................................................................................................98

3

&RQWHQWVRI<RXU%R[

Check-list of your accessories

Please make sure that the following items are included in the
box. If any items are missing, contact your dealer.

1. Projector

2. Quick start guide 3. Owner’s manual CD 4.Remote control

5. Power cord 6. Computer cable

4

Safety Instructions

This projector is designed and tested to meet the latest standards for safety of information technology

equipment. However, to ensure safe use of this product, it is important that you follow

the instructions

mentioned in this manual and marked on the product.

WARNING / CAUTION

1. If a problem occurs:

-If smoke or strange odors arise, continued use
could result in fire or electrical shock.

-If there is no image or sound, or the sound is
distorted in the projector. In some cases,
immediately remove the power cable from the
power outlet. After making sure that the unit has
stopped, contact your dealer for repairs.
Never attempt to repair by yourself because this
is dangerous.

2. Do....

-Place the projector in a stable horizontal
position.

-Put the projector in a cool place, and ensure that
there is sufficient ventilation.

-To consult with your dealer before a special
installation such as suspending from a ceiling.

3. Do not....

-Do not place the projector on an unstable,
slanted or vibrating surface such as a wobbly or
inclined stand.

-Do not cover the projector's vents. Keep a space
of 20 cm or more between the projector and
other objects such as walls.

-Do not place the projector on metallic goods.

-Do not place the projector on carpet, cushions
or bedding. Do not place the projector in direct
sunlight or near hot objects such as heaters.

-Do not place anything near the projector lens or
vents, or on top of the projector.

-Do not place anything that may be sucked into
or stick to the vents next to the projector.

-Do not use this projector if there is no image or
sound, or if the sound is distorted.

-Do not place this projector in a container
containing liquid.

4. While connecting, make sure that the shape
of the cable‟s connector fits the port to
connect with. Be sure to tighten the screws
on connectors with screws.

5. Do not disassemble or modify the projector
and accessories.

6. Be careful not to damage the cables, and do
not use damaged cables.

7. Use appropriate accessories or otherwise
designed cables. Ask your dealer about non­accessory cables that may have other lengths.

8. Make sure that devices are connected to the
correct ports. An incorrect connection may
result in malfunction or damage to the device
and the projector.

9. Do not look through the lens when the lamp
is on. The powerful light could adversely
affect vision. Use special caution in
households where children are present.

10. A strong light is emitted when the projector

power on. Do not look into the lens of the
projector or look inside of the projector.

Do not place the projector on either side to
project an image.

NO SIDEWARD

5

Safety Labels

WARNING

Do not look through the lens when the lamp is on.

Never look through the lens when the lamp is on. The powerful light could
adversely affect vision. Use special caution in households where children are
present.

Avoid shock or impact on the projector.

If the projector should fall, resulting in damage to the cabinet, immediately
turn off the power switch, disconnect the power plug from the power outlet
and contact your dealer.
Continued use could result in fire or electrical shock.

Do not place this projector in a container containing liquid. Do not place flower
vases, flowerpots, cups, cosmetics, liquids such as water, etc., on top of this projector.

Do not use any power cable except those supplied with the projector.

The use of any other power cable could result in fire or electrical shock.

Do not shine the laser beam onto yourself or other.

The laser pointer function of projector remote control emits class II laser beam.
Do not look directly into the laser beam outlet or direct the laser beam at other people.
Vision can be impaired if the laser beam enters the eyes. Especially pay attention if
children are present.

High temperatures are generated when the lamp is lit; so do not place objects in
front of the lens.

Allowing the proper amount of space on the top, sides, and rear of the projector cabinet is
critical for proper air circulation and cooling of the unit.
The dimensions shown here indicate the minimum space required. If the projector is to
be built into a compartment or similarly enclosed, these minimum distances must be
maintained.

Side and Top Rear

6

Safety Labels

Safety labels are used on or within the projector to alert you to items or areas
requiring your attention.

WARNING LABEL

EMI LABEL

LAMP DOOR WARNING LABEL

7

Part Names

Projector

1

1

1

1

1

1

1

1 Touch keypad

Operating system.

Front

IR

receiver

5 4 3 2

6

ventilation



2

Filter cover

Prevents dust and other foreign particles
from being drawn into the projector.

Remove the filter cover to clean the air
filter.

3

Foot adjust button

Lock / unlock the adjustable foot.

4

Front adjustable foot

Extend and retract to adjust the projection
angle.

5

Lens cover

Attach when not using to protect the lens
from becoming dirty or damaged

.

6

Focus ring

Use the focus ring to focus the projector
image.

Rotate the focus ring until the image is
clear.

7

Lamp door

The lamp unit is inside

8 Security bar

7

8

5 4 3 2

1

Outlet

7

6

8

8

Part Names

Touch

Keypad

1

1

1

1

1

1

15 16

9 9

14

10

13

11

12

9 VOLUME + / -

Sound louder or lower.

14

INPUT

Select input source:

RGB 1 RGB 2

HDMI

10

MENU

Display or hide the OSD main menu

S-Video

Note:

Video

USB

11

AUTO

Automatically adjust the setting to match
the current input source.

12

(POWER)

Power On / Off.

13

BLANK

Blank the projected image. The time of
Blank mode can be set in 15 minutes, 30
minutes or 60 minutes. The projector will
shut down automatically after passing each
set time.

If the projector cannot capture the signals
within 15 minutes, it will be shut down
automatically.

15

POWER INDICATOR

Light on or flash to indicate the operating
status of the projector.

16

LAMP INDICATOR

Indicates the status of the projector:
internal temperature, lamp door is not
properly closed or the projector is cooling
down.

9

Part Names

Rear

A B C D E

F G H I J

K L

Q

P

A

REAR IR RECEIVER

O N

M

I

LAN

B

USB Port (USB-B Type)

Connect a USB cable to a computer to
control computer Interactive functions.

C

RS-232C

Serial data port for controlling the projector
with a computer or other RS-232 control

Please

see

page 76

Network

Control

Application for details.

J

S-VIDEO

Input the S-Video signal from a video
source.

K

AUDIO IN 3, R / L

device.

D

AUDIO IN 1 &

P

AUDIO IN 2

RCA type corresponds to video input.

Mini jack port corresponds to computer
input. (RGB IN 1→AUDIO IN 1, RGB IN
2→AUDIO IN 2)

E

RGB IN 1

Input analog RGB signal from a computer.

F

HDMI

I n p u t d i g i t a l HDMI si g n a l f r o m a
computer & video source.

G

USB Port (USB-A Type)

L

SPEAKER

M

VIDEO

To composite the video signal from a video
source.

N

RGB IN 2/OUT

Input analog RGB signal from a computer
or connect an external monitor to this
connection to view the "RGB IN" input.

1. Supports USB Storage Device and USB
compatible hard disks.

2. Supports wireless (WiFi) USB dongle
for wirelessly projecting the computer‟s
image.

H

USB Display Port (Mini-USB

Type)

Supports USB mini-B connection from
the

compute

rs USB Port by using the
USB mini-B type to A type cable. It also
can access the internal memory from
projector to display the data.

O

AUDIO OUT

This jack outputs the audio signal from

computer& audio signal to external audio
equipment.

Q

Slot for Kensington Micro

Saver

Security System

Built-in security

slot.

This

security

slot

supports

the Micro

Saver® Security System. Micro

Saver®

is a

registered trademark

of Kensington

Microware

Inc. The logo is

trademarked

and

owned by

Kensington Microware

Inc.

1

Setting Up

Image size (inch)

Distanc e (cm)

Offset(cm)

49

63.6

20.8

60

78.7

25.4 70

92.5

29.7 80

106.2

33.9 90

120.0

38.2 94.3

126.0

40.0

Arrangement

1. Before installation, make sure that the projector is turned off and the power cord is disconnected.

2. Do not set up and move the projector, while it is hot.

3. The distance between the projector and screen determines the actual image size. Refer to the table
below to determine the screen size at a given distance.

►Note: The dimensions in the table below are approximate.

4:3

16:10

Image size (inch)

Distanc e (cm)

Offset(cm)

50

61.0

7.62

60

74.0

9.1 70

87.0

10.6 80

100.0

12.2

90

113.0

13.7 100

126.0

15.2

Distance (cm)

Image size(inch)

Offset (cm)

When installed against a wall, leave about 20cm (7.9in.) between the projector and the wall.

11

Setting Up

WARNING

●

Do not touch around the lamp cover and the
exhaust vents during use or just after use, since it is

too hot.

●

An apparatus with CLASS I construction shall
be connected to a MAINS socket outlet with a

protective earthing connection.

●

The MAINS plug or an appliance coupler shall
remain readily operable.

WARNING

● A strong light is emitted when the projector’s power

is on. Do not look into the lens of the projector
or look inside of the projector through any of the
projector’s openings.

CAUTION

●

Do not turn off the AC power for 60 seconds
after the lamp is turned on. Doing so could cause

premature lamp failure.

Power ON / OFF

AC inlet

Outlet

Focus ring

1.

2.

3.~4.

5.

Turning On The Power

1. Make sure that power cord is firmly and
correctly connected to the projector.

2. The green Power indicator blinks slowly.

3. Remove the lens cover.

4. Press POWER button on the Touch Keypad
or the remote control to turn on the projector.

5. Rotate the focus ring to adjust the focus.

Turning Off The Power

1. Press the POWER button on the Touch
Keypad or the remote control. The "power

off" conrmation message will appear.

2. Press the POWER button again while the
message is shown on the screen.

3. When the projector enters "Standby" mode,
the green Power indicator blinks slowly.

4. The projector cannot be turned on while red
"Lamp indicator" is blinking slowly in cooling
mode.

5. If you don’t use the projector for a long time,
remove power cord.

1

Setting Up

Setting Up The Projector

The projector supports the following four different projection methods.

1. Front projection

2. Rear projection

3. Rear ceiling projection

4. Front ceiling projection

The projector can be installed pitched by any
angle (360 degree) without any setting in fan
mode. As for rolling it must be within 10 degree.

Special installation is required in order to suspend the projector from the ceiling. Please ask your
dealer for details.

13

Setting Up

Ceiling Mounted Installation Guide

Attach ceiling mount at four-suspension bracket xing points when suspending from a ceiling.

Special installation is required in order to suspend the projector from the ceiling. Please ask your
dealer for details.

MAX M4x8 mm For Mounting.

WARNING

●

Do not grasp the security anchor to carry projector, since it is not designed for it.

●

The security anchor is not for comprehensive theft prevention measures. It is intended to be
used as supplemental theft prevention measure.

Security Anchor

The product is equipped with security anchor and PIN
LOCK (See page71 for detials) functions to help prevent
unauthorized removal of the projector.

14

Setting Up

Adjusting The Projector’s Elevation

Use the adjustable foot at the front of the projector to set the image height.

CAUTION

●

The adjustment range of front adjustable

feet is 0 to 7 degrees.

●

When the feet are adjusted, it may cause
the shape of the projected image to become
distorted. Use the keystone correction
function to correct this distortion.

1

Holding the projector, push the foot adjust

buttons to loosen the front adjustable foot.

12

Position the front side of the projector to the

desired height.

3

Release the foot adjust buttons in order to

lock the front adjustable feet.

14

Please make sure that the front adjustable

feet are locked.

15

Please rotate the adjustable feet when ne

adjustment of tilt is needed.

1

Setting Up

How To Connect

Laptop or desktop computer

Video

recorder

DVD

Player, etc.

RS-232C terminal RGB Output HDMI

S-VIDEO Output

AUDIO O utput

White(L)/R ed(R)

AUDIO Input

White(L)/R ed(R)

RGB Output/Input

VIDEO Outp ut

AUDIO Output

White(L)/R ed(R)

Video

recorder, etc.

Audio

amplifier, etc.

Before starting, make sure that the projector and computer are both turned off.

Connect the computer

Connect the computer cable from the computer to the projector's RGB IN.
Connect a computer cable from the MONITOR OUT to an external monitor to view the
signal on RGB IN. Tighten the screw on all connectors.

Laptop or desktop computer

Connect the audio cable if necessary

1. Please connect the audio cable to the AUDIO IN 1 if the computer cable is connected
to the projector's RGB IN.

2. Please connect the audio cable to the AUDIO IN 2 if the computer cable is connected
to the projector's RGB IN 2.

3. Please connect the audio cable to the AUDIO IN 3 if the video cables are connected to
the VEDIO / S-VIDEO port of the projector.

1

Setting Up

●If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, please check that the video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.

●Many laptops do not turn on their external video ports when connected to a projector.
Usually a key combination like Fn + F3 or CRT/LCD key turns the external display on /
off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on
the laptop. Press Fn and the labeled function key simultaneously. Refer to your laptop‟s
documentation to discover your laptop‟s key combination.

1

Remote Control

Remote Control Batteries Installation

1. Remove the battery cover.

2. Load the batteries.
Make sure the poles are correctly oriented.

3. Close the battery cover.

Caution

● Avoid excessive heat and humidity.

● Do not drop the remote control.

● If the remote control will not be used for an extended period, remove the batteries.

● Do not expose the remote control to water or moisture. This could result in malfunction.

● Replace the battery when remote control operation becomes sluggish or unresponsive.

● Do not place the remote control close to the cooling fan of the projector.

● Do not use batteries of different types at the same time.

● Do not mix a new battery with used one. Make sure the plus and terminals are correctly

aligned when loading batteries.

● Dispose of batteries in accordance with environmental laws.

● Do not disassemble the remote control. If the remote control needs service, please contact

your dealer.

● The batteries (battery pack or batteries installed) shall not be exposed to excessive heat

such as sunshine, fire or the like.

1

Remote Control

POWER

Power on / operation mode, standby mode, cool
down mode.

INPUT

Select input source:

Quick Key

If it is not in the On-Screen Display main menu,
press the

button as the quick key.

RGB 1 RGB 2 HDMI

Press or to select the item.

MENU

S-Video

Video

USB

V keystone

V

olume

Brightness

Contrast

Display or hide the On-Screen Display main menu
page.

Press or to adjust the value

Press or to select On-Screen
Display menu item.

Press or to select and adjust the
function of On-Screen Display menu item or value.

LASER

Aim the remote control at the screen, press and
hold button to activate the laser pointer.

MUTE

Mute audio.

Press / / / to select the EZ
Suite On-Screen Display menu item.

ESC

Escape current status (to set the EZ Suite On-
Screen Display menu item).

ENTER

Select current status (to set the EZ Suite On-Screen
Display menu item).

AUTO

Refresh the current image.

BLANK

Hide the current image, become black color on the
screen.

19

EZ Suite

Main Menu Layout & Function Definition

Main-items

Function

Definition

Sub-Function

Definition

Description

EZ Suite

Photo Support internal

EZ Media
Function

EZ Display
Function

Internal Memory

USB

EZ USB

EZ WiFi

EZ LAN

Video
Audio

Office viewer
Photo
Video
Audio
Office viewer

memory,
USB compatible hard
disks,
Support Photo,
Video, Audio Music
and Office viewer.

Support
USB Display/
WiFi Display/
LAN Display

Version Function

Setting &
Configuration

System

Video

Photo

Audio

WiFi

Connect PC

Language
Update
Display Ratio
Repeat Mode
Display Ratio
Slideshow
Slideshow
Duration

Repeat Mode

AP mode
Client mode

Connect PC

Configuration and
Setting.

20

EZ Suite(EZ Media Function)

Before to use:

1. Use the or buttons on the remote control to select an item.

2. Use the ENTER button on the remote control to enter item.

3. Use

the ESC button

on

the remote control to exit items.

1. EZ Media Function: Layout & Behavior

Support internal memory and USB-disk device (Support Photo, Video, Music, office
viewer)

EZ Media Function

Internal Memory
USB

Photo

Video

Audio

Office viewer

►Note:

1. Internal Memory:

Internal memory, supports the memory size is around 1.5GB.

2. USB:

Support USB Storage Device Type:
USB Flash Device (~64 GB), USB compatible hard disks.

Support FAT16, FAT32, and NTFS File system.

3. Limitation (each type of storage):

Support maximum of 999 directories and maximum of 9,999 Files
Support at most 10th level directory

4. Even if the inserted USB Storage Device or used Internal memory contains a mix

of audio music, video, and photo files, you can only browse and playback one
type of file at a time. For example, if you enter the Audio music folder, only
audio music files can be browsed, added to playlist and played back. To browse
photo files, go back to the EZ Media screen and select Photo.

21

EZ Suite(EZ Media Function)

1.1 Photo Function

It will show the file name / thumbnails display / file number progress bar

1. From the Photo layout. Press the or buttons on the
remote control to select the file.

2. While the highlighted photo file is selected, press the ENTER button on the
remote control, the screen will display the selected file, and it will enter the
Browse mode.

3. Browse mode:

22

EZ Suite(EZ Media Function)

Photo navigator toolbar :

Rotation

Zoom in

Previous

Next

Slide how

On/Off

Delete

Copy

Info

Quit

Press the , buttons on the remote control, to highlight control icon and press the
ENTER button on the remote control to select.

Rotation: To rotate an image.

Using the or buttons on the remote control to rotate the image.
It will resume the image when press the ESC button on the remote control to
exit shown image.

Zoom in: To magnify a photo.

Press the ENTER button again to expend the image. It supports x1, x2, x3
and x4 magnification.
During enlarged projection, use the , , or buttons on the
remote control to move the image area.
It will resume the image when press ESC on the remote control to exit shown
image.

Previous: Play previous photo.
Next: Play next one photo.
Slide Show On/Off: Turn On/Off the slide show function.

*The slide show will operate after the toolbar is hidden.
*There have a turn on the slide show function on the "Photo

Setting" menu (see page 48 for more information).

Delete: To delete the photo file.
Copy: To copy the current display photo file, it will save the photo to internal memory.
Info: Showing the information of the current display photo file.
Quit: To quit browse mode and return to sub-menu.

4. To return to the sub- menu, press the ESC button on the remote control.

►Note:

1. Supports *.jpg, *.jpeg and *.bmp file format.

2. Support files sorting by file name.

3. An on-screen image presented on slides automatically, when the setting of Photo Slide

show is enable.

*For more information please check the page 48 for "Photo Setting"

23

EZ Suite(EZ Media Function)

1.2 Video Function

It will show the file name/ file list /file size/ file number progress bar

1. From the Video layout. Press the or buttons on the remote
control, to highlight the file of video playlist and press the ENTER button
on the remote control to display.

2. Press the ENTER button and a pop-up video navigator toolbar will
be displayed when the video is performed.

Video navigator toolbar:

Play fast

backward

Pause

Play

Play fast

forward

Repeat

mode

Play fast backward: To play fast backward by press the button.

Support x1, x2, x4 and x8 speeds.

Pause / Play: To pause or play the video by press the ENTER button.
Play fast forward: To play fast forward by press the button.

Support x1, x2, x4 and x8 speeds.

Repeat mode: Show the status of repeat mode.

Single display mode

Sequence repeat display

mode

24

EZ Suite(EZ Media Function)

► While video navigator toolbar is disappeared, press the or on the remote

control to play previous/next video file.

►Note:

1. Supports MPEG1/2/4, H264, WMV, RMVB video format, up to 1080P (20Mbps)
resolution. Please refer to the multimedia support list.

2. Supports files sorting by file name

3. Video play: Supports original size and full screen size display

►For more information, please check the page 47 for Video Setting.

1.3 Audio Function

It will show the file name/ file list /file size/ file number progress bar.

25

EZ Suite(EZ Media Function)

1. From the Audio layout. Press the or buttons on the remote control to

highlight the file of audio playlist and press ENTER button to perform.

Audio navigator toolbar:

Previous

Play fast

backward

Pause

Play

Play fast

forward

Next

Repeat

mode

Previous: Play previous audio music file by pressing

button twice.

Play fast backward: To play fast backward by pressing button.
Pause / Play: To pause or play the video, press the ENTER button.
Play Fast forward: Play fast forward by pressing button twice.
Next: Play next audio music file by pressing button.
Repeat mode: Show the status of repeat mode.

Single display mode
Sequence repeat display mode

26

EZ Suite(EZ Media Function)

Sound

Spectrum

Show the total time and indicate current playing time

►Note :

1. Support mp3, wma, ogg, and wav audio file format

2. Support file sorting by file name and

modification

date same as photo function

*For more information, please check the page 48 for Audio Setting.

1.4 Office Viewer Function

1.

Select and enter a document file that you want to browse; it will show the translucent

operating menu around 5 seconds on the screen.

2. The document displays on the screen.

Press button will show the translucent Tool bar on the screen; it will help you to
browse the document.

27

EZ Suite(EZ Media Function)

Operation info :

◄► Zoom In / Zoom out

Crops the image, and magnifies or reduces the result of the cropping.

▲▼Page up/Page down

These two buttons are used to go to the previous page or the next page in

documents.

Rotate

Press “Enter” button for movement of document around a center of rotation.

Exit

Press “ESC” button to exit browse document.

►Note:

1. Embedded Picsel Office Viewer

2. Support Office 2010 (Word, Excel, PowerPoint), Adobe PDF & Plain text (TXT) format

Operation info :

▲▼◄►

Navigator

Use up/down/left/right keys.

Display mode

Press the ENTER button to set display mode.

Tool bar

Press the ESC button to show tool menu bar.

28

EZ Suite(EZ Display Function)

2. EZ Display Function: Layout & Behavior

Support USB Display, WiFi Display, LAN Display.

EZ Display Function

EZ USB

EZ WiFi

EZ LAN

Function

Description

OS system

EZ USB

Display PC Screen with USB cable

Extended Display with USB Cable

Windows OS, Mac OS

EZ WiFi

Wirelessly project the

computer

‟s

screen

Windows OS, Mac OS

EZ LAN

Display computer ‟s screen with

Ethernet

Windows OS, Mac OS