Boss Audio 840UBI User Manual

10 R - 02 0896

1. BUTTONS LOCATION AND FUNCTIONS

1. Panel Release Button

2. Menu Button

3. CD Eject Button

4. Power / Mute Button

5. Reject /End Call Button / ESC Button

6. Phone Answer Button / Call Transfer Button

7. Preset Memory Buttons

8. iX-Bass Button / TA Button

9. Source Button

10. Volume Knob

11. Automatically Store / Preset Scan Button

12. Band/MP3SerachButton

13. Tuning Up/Down & Track Up / Down Buttons

14. Remote Control Receiver

15. Information Button

16. Aux In Jack

17. USB Slot

1. Entriegel-Taste Bedienteil

2. Menu-Taste

3. CD-Auswurftaste

4. Stumm-Taste / Einschalt-Taste

5. Anruf annehmen / ESC-Taste

6. Taste/Anruf annehmen / Anruf Transfer

7. Senderspeichertasten

8. iX-Bass-Taste / TA-Taste

9. Source-Taste

10. Lautstärkenregler

11. AMS Taste / MP3 Suchlauf Taste

12. Frequenzband-Taste / MP3 Eingabe-Taste

13. Titel AUF / AB - Taste

14. Fernbedienungs-Taste

15. INFO-Taste

16. Front-Audio-Anschluss

17. TasteUSB -

13 7

1. Tecla para remover o painel frontal

2. Tecla de ajuste de menu

3. Tecla para ejetar o disco

4. Tecla Ligar/desligar & Tecla Mute

5. Apagar Arquivo & Rejeitar / Encerrar Uma Chamada / Tecla ESC

6. Tecla Para Atender O Telefone / Transferir a Chamada

7. Teclas de memória de estações

8. Função IX-BASS / Tecal TA

9. Tecla Source

10. Controle de volume

11. Memorização automática (As) / Preset Scan (Ps)

12. Tecla Banda / MP3 Search

13. Teclas de sintonização de estações / mudança de faixas de música

14. Sensor do controle remoto

15. Informação MP3-iD3

16. Entrada Auxiliar

17.Entrada USB

1. Extracción del panel frontal

2. Tecla Menu

3. Apertura del panel motorizado y expulsión del disco

4. Silenciamiento rápido / Encendido/Apagado

5. Rechazar llamadaTerminar llamada / Botón ESC

6. Contestar teléfono / Transferir llamada

7. Botones de estaciones memorizadas

8. Botón iX-Bass / Botón TA

9. Selección modos Radio/CD/Entrada auxiliar

10. Botón De Volumen

11. Memorización Automática de emisoras / selección de memorias

12. Selector Bandas / Bajos/MP3

13. Botón de selección de emisoras & banda de música

14. Receptor de control remoto

15. ID3 TAG muestra

16. Entrada de auxiliar

17. Entrada de USB

1. Bouton De Déclenchement Du Panneau

2. Bouton De Sélection Menu / Entrée De MP3

3. Bouton Éjection D'un Cd

4. Bouton D'assourdissement / Bouton D'alimentation

5. SupprimerFichier/Annuler / Bouton ESC

6. Téléphone/Répondre Appeler / TransfertAppe

7. Boutons Des Stations Préréglées (m1 ~m6)

8. Bouton De iX-Bass / Button TA

9. Bouton De Régime

10. Bouton De Volume

11. Bouton De Stockage Des Stations Dans La Mémoire

12. Bouton De Bande / Entrée De MP3

13. Bouton De Recherche Des Stations/pistes : En Avant / En Arrière

14. Récepteur De La Commande À Distance

15.Affichage D'information Sur Les Disques MP3

16. Aux A Jack

17. USB Slot

1. Tasto Rilascio Frontalino

2. Menu Controlla

3. Tasto Eject

4. Tasto Mute / Tasto Power

5. Rifiuta/termina chiamata / Tasto ESC

6. TelefonoRisposta / Trasferimento chiamata

7. Tasti Stazioni Memorie Preimpostate

8. Bottone Bassi / Bottone TA

9. Tasto Mode

10. Tasto Volume

11. Tasto Menu & AS/PS

12. Tasto Banda/Forte & Enter MP3

13. Tasto sintonizzazione su/gui & traccia su/gui

14. Destinatario di controllo remoto

15. Tasto informazioni

16. Entrada Aux

17. Entrada Usb

This radio is equipped with the most advanced "TOUCH SENSE PANEL", so that it is easy and convenient to use while driving.

Here are some tips to show you how easy it is to use this touch sense panel:

Tips

Using a very light touch on the radio panel will activate that feature. You will not need to "PRESS" hard on the panel to make this radio change features.

The power button along with some of the buttons that have dual functions, will need to be "TOUCHED" from 2 to 3 seconds to make the change.

The best area to "TOUCH" on the panel to make it activate is the illuminated or lighted area. For example, just touch for 2 to 3 seconds the illuminated power symbol and the unit will turn on or off.

2. NOTE OF DISCS

MOISTURE CONDENSATION

On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated.

NOTES ON CDs

A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge. To keep the disc clean, do not touch the surface (P.1).

P. 1

Do not stick paper or tape on the disc (P.2).

P. 2

Do not expose the discs to direct sunlight or

heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car (P.3).

P. 3

Before playing, clean the discs with an optional cleaning cloth. Wipe each disc from the centre out (P.4).

NOTES ON DISCS

If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs.

Do not use second-hand or rental CDs that have a sticky residue on the surface (for example, from peeled-off stickers or from ink, or glue leaking from under the stickers).

There are paste residue. Ink is sticky (P.5).

P. 5

Do not use rental CDs with old labels that are beginning to peel off.

Stickers that are beginning to peel away, leaving a sticky residue (P.6).

P. 6

Do not use your CDs with labels or stickers attached.

Labels are attached (P.7).

Do Not Use Special Shape CDs

P. 7

Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.(P.8).

**** ******* *******

*******

**************

*******

P. 4

Do not use solvents such as benzine,

thinner,commercially available cleaners, or antistatic spray intended for analog discs.

P. 8

Be sure to use CDs with disc mark CD-Rs and CD-RWs which have not

undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CDR/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs record on CD-R or CD-RW.

CDE VERSION

E - 1

3. INSTALLATION

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance.

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive vibration. Be sure to remove the front panel before installing the unit.

DIN FRONT/REAR-MOUNT

This unit can be property installed either from “Front” (conventional DIN Front-mount) or “Rear”(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods A and B.

DIN FRONT-MOUNT (Method A) Installation the unit

182

1. Dashboard

2. Holder After inserting the half sleeve into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place.

3. Screw

1. Dashboard

2. Nut (5mm)

3. Spring washer

4. Screw (4x12mm)

5. Screw

6. Support Strap Be sure to use the support strap to secure

the back of the unit in place. The strap can be bent by hand to the desired angle.

7. Plain washer

E - 2

Removing the unit

a. Frame b. Insert fingers into the groove in the

front of frame and pull out to remove the frame. (When re-attaching the

Trim Plate Installation:

Push the trim plate against the chassis until it is fitted. You must do this before you install the front panel, otherwise it can't be attached.

DIN REAR-MOUNT (METHOD B)

Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket.

frame, point the side with a groove down wards and attach it.)

c. Insert the levers supplied with the unit

into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard.

1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.

2. Screw

3. Factory radio mounting bracket.

4. Dashboard or Console

5. Hook (Remove this part)

Note: the mounting box, outer trim ring, and half-sleeve are not used for method B installation.

E - 3

4. DETACHABLE CONTROL PANEL (D.C.P.)

Removing The Detachable Control Panel (D.C.P.).

1. Turn the power off

2. Press the D.C.P. release button

PANEL RELEASE BUTTON

Attaching the DCP

3. Remove the D.C.P.

1. Attach the panel at the right side first, with point B on the main unit touching point A on the D.C.P. (As shown on the diagram).

2. Then press the left side of D.C.P. onto the main unit until a “click” sound is heard.

CAUTION

DO NOT insert the D.C.P from the left side. Doing so may damage it. The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it to fall. To prevent damage to the D.C.P, always store it in a protective case after detaching it. The rear connector that connects the main unit and the D.C.P is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

Note:

If the D.C.P is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the

Socket

back of the D.C.P.

RESETTING THE UNIT:

After releasing the front panel, use a pencil or any non-metalic object to press & hold the reset button for five seconds to reset the unit.

T S EE

E - 4

5. WIRING DIAGRAM (BUILT-IN ISO)

FUSE

/SALIDA DE LINEA TRASERA/LINE OUT POSTERIORE

FRONT LINE OUT/VORDERER AUSGANG/SAÍDA FRONTAL

RCA-TO-RCA CABLES (not supplied)

RCA-TO-RCA-KABEL (nicht geliefert)

CABLES RCA-TO-RCA (non fournis.)

CONNECTOR B

ANSCHLUSS B CONE CTOR B CONECTEOR B

CONNECTOR B CONNETTORE B

FIGURE 2/ABB.2/DESSIN 2/FIGURA 2/FIGURE 2/FIG 2

AMP

CABOS RCA A RCA (não fornecidos)

CABLES RCA A RCA (no incluidos)

CAVO RCA A RCA ( non fornito)

CONNECTOR A

ANSCHLUSS A

5 6

CONECTOR A

CONECTEOR A

CONNECTOR A

3 4

CONNETTORE A

1 2

L-CH

R-CH

iPod

WHITE

iPod READY CABLE

REAR

　R-CH

/SALIDA DE LINEA TRASERA/

REAR LINE OUT/

RÜCKANSCHLUSS/SORTIE ARRIERE/SAIDA TRASEIRA

LINE OUT POSTERIORE

　 L-CH

AMP

ANTENNA CABLE INPUT

ANTENNENVERLÄ NGERUNGS KABEL

CÂBLE D'EXTENSION D' ANTENNE

ENTRADA PARA CABO DE ANTENA CABLE DE ANTENA

CAVO ANTENNA ESTENDIBILE

E - 5

6. BASIC OPERATIONS

2) 　PANEL RELEASE BUTTON (REL)

Press this button to remove the control panel.

3) POWER ON/OFF BUTTON ( POWER/MUTE )

Press POWER/MUTE button or any other button on the front of the radio (except Open/Eject) to turn the unit on. And hold & press POWER /MUTE button again to turn the unit off.

3) MUTE BUTTON (POWER/MUTE)

Short press the POWER/MUTE button momentarily to mute the audio volume, and "MUTE" will flash in the display. Press the POWER/MUTE button again to restore volume to the previous setting.

10) iX-BASS BUTTON (XBS)

Press the XBS button to turn on the iX-Bass function, and the “X-BAS” icon will appear on the LCD display. Press the XBS button again to turn off the iX-Bass function.

MODE BUTTON (MODE)

Press MODE button to select a different mode of operation as indicated on the display panel. Available modes include TUNER, DISC, USB, SD CARD BT AUDIO iPod and Aux In

16) AUX IN JACK ON FRONT PANEL

Connect the external signal to AUX in jack located at the front of the panel , then press Mode button to select Aux mode. Press Mode Button again to cancel Aux Mode and return to previous mode.

AUX IN

FRONT CABINET

LEFT TRACK

RIGHT TRACK

GROUND

OPEN THE AUX-IN JACK DOOR/COVER TO ACCESS TO THE AUX-IN JACK

AUX IN

5) ENCODER VOLUME BUTTON

To increase the volume, rotate the Encoder Volume Knob clockwise. To decrease the volume, rotate the Encoder Volume Knob counter clockwise. When volume is adjusted, the volume level will be shown on the display panel as a number ranging from 0 (lowest) to 46 (highest).

15) EJECT BUTTON ( )

Press this button to eject the CD from the unit. The receiver will switches to radio mode automatically.

E - 6

7. SYSTEM MENU SETTING

1) MENU FUNCTION LIST (MENU)

Hold& Press MENU button to access into the System Menu setting mode. Will appear in the display momentarily. Navigate the menu by pressing MENU momentarily to move to the next option. Once the desired option appears in the display, adjust that option by rotating the Encoder Volume Knob(press the volume up / down button ) within 5 seconds. The following options are adjusted through this menu feature.

Re-connection (RE-CON / DIS-CON )

This feature allows to Re-connect or Dis-connect to the paired mobile phone or Bluetooth device by manually. Under the Menu- “RE-CON”mode, Rotate the Encoder Volume Knob to navigate thru “RE-CON” (re-connection) and “DIS-CON”(Dis-connection). After selected the mode for connection then press Audio button to start activating the connection mode.

Bluetooth On/Off ( BT On/Off )

User can rotate the Encoder Volume Knob to turn On / Off the Bluetooth function, then the “ Bluetooth” icon will be appear in the display, once bluetooth function is turned on.

Local / Distance Select (SEEK LOC/DX)

This feature is used to designate the strength of the signals at which the radio will stop during automatic tuning. "Distance" is the default, allowing the radio to stop at a broader range of signals. To set the unit to select only strong local stations during automatic tuning, rotate the Encoder Volume Knob(Press the volume up/down button) select the Local mode, the "LOC" icon will be appears in the display.

PTY (Program Type)

Once into the PTY mode, you can be press Audio button to get into program type item, and rotate Encoder Volume Konb to selected category.

Music Group

POP M, ROCK M

EASY M, LIGHT M CLASSICS, OTHER M

JAZZ M, COUNTRY NATION M, OLDIES M

FOLK M, A-TEXT, ALARM

AF ON/OFF (Alternate Frequencies) User can rotate the Encoder Volume Knob to turn On / Off the AF ( Alternate Frequencies ) function. When AF in On mode, the unit will be searches for another station with stronger signal but with the same program identification as the current station automatically. REG ON/OFF (Regional Radio) User can rotate the Encoder Volume Knob to turn On / Off the Regional function. [ REG ON ]: Only stations in the current region can be tuned to automatically. [REG OFF]: All stations can be tuned to automatically.

AREA (TUNER FREQUENCY SPACING)

This option allows the selection of the frequency spacing appropriate for your area. "AREA U.S.A." is the default setting. Rotate the Encoder Volume Knob to select the U.S.A., EUR(Europe)

Speech Group

NEWS, AFFAIRS, INFO SPORT, EDUCATE, DRAMA

CULTURE, SCIENCE, VARIED WEATHER,FINANCE, CHILDREN

SOCIAL, RELIGION, PHONE IN TRAVEL, LEISURE, DOCUMENT

E - 7

+ 22 hidden pages