Boss Audio 802UA User Manual

DESCRIPTION OF CONTROLS ON THE FRONT CONTROL PANEL

Front Control Panel

Front Cabinet after removing Front Control Panel

1. RELEASE button

2. SEL & VOL knob

3. POWER & MUTE button

4. LCD 5&6. >>| And |<< buttons

7. BAND button

8. MODE button

9. 1/TOP/>|| button

10. 2/INT button

11. 3/RPT button

12. 4/RDM button

13. 5 DIR- button

14. 6 DIR+ button

15. AUX IN jack

16. USB socket

17. APS button

18.IR Remote Sensor

19.Card slot

20.RESET

21. FLASHING LED

DESCRIPTION OF BUTTONS ON REMOTE CONTROL

REMOTE CONTROL

REMOTE CONTR OL

Load/unloading battery of remote control

1. Please remove insulating sheet out of remote control before use. Pull out insulating sheet in the direction as per fig. 1.

2. When changing battery for remote control, first pull the movable block hold in the direction as indicated in Fig. 2 arrow A. Then pull the battery holder out from the remote control in the direction as indicat ed in Fig.2 ar row B.

3. Replace the old battery by a new battery with (+) polarity side upward. Then return the battery holder to the remote control by pressing the battery holder. Please see Fig.3.

Note about the battery of remote control:

1. Improper use of battery may cause overheating or explosion. Which may result in jury or fire .

2. Battery leakage may cause damage to the remote control(Battery Life: 6 months with normal use in normal room temperature).

3. Do not short the battery.

4. Do not throw the battery into the fire.

5. To avoid the risk of accident, keep the battery out of reach of children.

1. Power On/Off

2. Mute Button

3. Loudness Button

4. Level/MENU UP Button

5. SEL/MENU Button

6. Level/MENU Down Button

7. MO/ST Button

8. A.P Button

9. Band Button

10. Mode Button 1 1. Tune/Seek Up/ Track Skip Up/FF Button

12. Tune/Se ek Down/ Track Skip Down/REW Button

13. SCAN BUTTON

14. Clock Display /Setting Button

15. LOC/DX Button

16. TOP/>||/Radio Preset 1

17. INT/Radio Preset 2

18. RPT/Radio Preset 3

19. RDM/Radio Preset 4

20. Radio Preset 5

21. Radio Preset 6

Common operation:

1. To turn the unit on/off . When the unit is power Off, it may be switched On by pressing any button except RELEASE button. When the unit is switched On, press and hold POWER button for more than 1 second, to switch the power off.

2. To select function mode Press MODE button to change function mode as follows:

-->TUNER -->USB(after inserting USB stick)-->CARD(after inserting SD card)--> AUX--> When there is no media (USB/CARD), that mode will be skipped.

3. To adjust the volume level Rotate VOL knob or press + or - button on remote control to adjust volume level during playback.

4. To mute or resume sound Press MUTE button to eliminate or resume sound immediately during playback. To resume the sound immedi ately, you can rotate VOL knob.

5. To set sound mode and menu

1).To set sound mode: Press SEL button shortly and repeatedly to select mode of VOL(volume), BASS (without preset DSP), TRE(treble)(without preset DSP), BAL(balance) and FAD (fader) in the sequence and circulation. In each mode, the waiting time is about 5 seconds, and when the waiting time is over, it will return to the last display mode. After selecting a sound mode, use volume control to set level of the selected sound mode.

2).To set menu: Press SEL button and hold for more than 2 seconds to turn on BEEP ON/BEEP OFF, then press SEL button shortly and repeatedly to select USER SET (FLAT/CLASSIC/ ROCK/POP), VOL LAST/VOL DEFA(AVOL) , AMERICA3/EUROPE(in RADIO mode), STEREO/MONO(in RADIO mode), LOUD OFF/LOUD ON, DX/LOCAL(in RADIO mo de) CLK ON/CLK OFF,CLK 12/CLK 24,CL(Adjust the clock))mode. After selecting a desired item, use volume control to set.

3) BEEP ON/BEEP OFF BEEP ON mode: The beep is generated when any key is pressed. BEEP OFF mode: The beep sound is disabled.

4) VOL LAST/VOL DEFA VOL LAST: The volume level when switching off will be restored with power On. VOL DEFA: The volume level of the main unit after power on is a constant valume. when selecting VOL DEFA item, press SEL button to display AVOL , then you can pre-set the constant volume level after power on with VOL control.

+ 5 hidden pages