Boss BV9380NV User Manual

Page 1
Page 2
INSTRUCTIONS
DVD Parental control function
DVD Parental control function: The default set for DVD is #8 adult, which means all grades of DVD can be read without entering password.
To change the default grade, you need to follow the below procedure: Press SETUP button on the remote, display will show the system set up menu and the submenu, select password and enter 0000, you will be able to choose the DVD grade as default.
DVD Parental control function
INSTRUCTIONS
Warning:
T
o ensure safety while driving and to comply with laws, drivers should not
watch video or operate the video device while driving.
NOTE:
1. Please read the instructions before using the unit, the damage caused by not following the instructions will not enjoy the warranty.
2.
To drive safely and avoid break the traffic rules, do not watch program and operate the unit while
driving.
3. To avoid short circuit, please do not exposure the device to rain.
4. To avoid short circuit, please do not put in the device or any metal objects left behind.
5. Not open the machine for maintenance by yourself, please go to the professional repair service station for repairing.
6. When the engine is turned off, please do not use the car audio a long time, otherwise the battery may run out.
7. Do not insert anything to the device’s vent and other openings.
8. Damage to the screen carefully! Do not use sharp objects push, rub, Stroke the screen.
ACCESSORY
Accessory
Quantity
Wire
USB Cable
Keys
2PCS
1PC
1PC
Remote controller
W
arranty card
1PC
2PCS
Page 3
INSTRUCTIONS INSTRUCTIONS
70dB
20Hz-20KHz
DVD player
S / N Ratio
Frequency response
530-1710KHz
522-1620KHz
32dB
AM tuner
US frequency range
European frequency range
Limit noise sensitivity
87.5-107.9MHz
87.5-108MHz
55dB
30dB
20-30dBuv
FM tuner
US frequency range
European frequency range
Signal / Noise ratio
Stereo separation
Search station volt
DC 12V
10.8-16.0V DC
15A
Negative ground
80 WattsX4 Channels
Power supply
Power range
t
Ground system
Max Current Consumption
Power Output
SPECITICATIONS
1
2
3
4
5
6
7
8
9
10
Panel Introduction
1. PWR/VOL Button
2.MUTE Button
3.NA
VI Button
4. RST
5. USB Slot
6. AUX Slot
7. IR
8.
9.Disk Load Slot
10.MAP/SD Slot
Page 4
TROUBLE SHOOTING
PROBLEM
CAUSE SOLUTION
After ignition switch off ,setting information all lose
Reset information and save
Change battery or fuse
Cannot power on
Change fuse same as the old one
Some factors cause MPU wrong operation
Press RES button on the panel by penpoint, then, power on
Poor performance of radio station
Cannot load disk There is a disk inside
Remove disc before inserting another one
W
eak signal
Move the car to another place, then research
Cannot play disc
Disc is scratched
Change new disc
Put wrong side of disc into the unit
Insert in the disk with sign side up
Clean lens by lens clean disc
Lens is dirty
Cannot switch language/subtitle
There is only one language/ subtitle in disc
If disc is not with multi-language/subtitle, it cannot switch language/subtitle
No image
Other factors cause MPU wrong operation
Press [RES] button on the panel by penpoint, then, power on
Cannot watch image during driving
It’
s not allowed to watch image
during driving
Park the car in a safe place, put the car stall in “ P ” postion, pull up the hand brake, parking brake wire must be grounded
Check fuse
This player is equipped with ISO standard connector, please
follow below instruction:
Yellow – 12 V Constant
Black – Ground wire
Blue - Power
Antenna / Remote
Amp Turn On
Orange – Back-Up Camera T
rigger (+)
Red -
ACC ON (+12V)
Parking Brake (-)
White/White black - Left front speaker (+/-)
Purple/Purple black - Right rear speaker (+/-)
Green/Green black - Left rear speaker (+/-)
Grey/Grey black - Right front speaker (+/-)
ANT-FM/AM antenna
G1
- Red Rear RCA R output
G2 - White Rear RCA L output
G3 - Yellow VIDEO–OUT1
G4 - Brown Subwoofer output
G5 - Yellow Rear view input
G6 - Yellow VIDEO –OUT2
G7 - Red AUX R Audio input
G8 - White AUX L Audio input
G9 - Yellow Video input
E3-White
Learning SWC
E1-Black Learning SWC GND
E2-Brown Learning SWC
E4-Dark grey with Red /White tip
Front RCA output (Right Red Left White)
E5-Rear USB Plug
E
1.Black GND battery -
2.Yellow BATT battery +
3.Red ACC switch control
4.Braking Wire
5.NC
6.CCD control
7.Blue ANT Radio automatic antenna
8.NC
9.Purple RR+ rear right speaker +
10.Purple/black RR- rear right speaker –
11.Grey FR+ front right speaker +
12. Grey/black FR- front right speaker –
13.White FL+ front left speaker +
14.White/black FL- front left speaker –
15.Green RL+ rear left speaker +
16. Green/black RL- rear left speaker –
B
-GPS
antenna
E6-BT MIC
F
2
1
3 15
166
4
5
791113
81
0
14
12
5
G1G2G3
G4G5
G6
G7G8G9
RRRL
V-OUT1
V-OUT2
AUX-RAUX-L
V-IN
CAM
S
W
D
ANT
E
F
B
5
D
-Media
1.
Press this button will turn on power
, during working longer press this button will turn of
f power, on any mode, shortly press will return main menu, rotate this button will adjust volume level.
2. MUTE button
Press this button to shut off sound output, repress this button to resume sound output; Press this button longer to turn on/off TFT LCD display.
3. NAVI button
Press this button for the navigation.
4. RST
Press this button and this unit will be restored to the initial state.
5. Dual (front and rear) USB
Insert USB removable device so as to read audio/video files. Warning: You can only use either front or rear USB at a time. Never connect both front and rear USB at the same time! This could cause malfunctions.
6. Dual (front and rear) AUX
To input external audio. Warning: You can only use either front or rear AUX at a time. Never connect both front and rear AUX at the same time.
7. IR
To receive infrared signal from the remote control.
10.
Insert SD card, the unit will play the files automatically.
PWR/VOL button
8.
Press this button can eject the disc.
9. Disk load slot
Opening for disks to enter or retreat.
MAP/SD Slot
Insert map card to read navigation map data.
WIRING DIAGRAMBASIC FUNCTION
Page 5
REMOTE CONTROL FUNCTION
28
1. POWER
Press once to switch on, press again to switch off.
2. MUTE Button
Press once to turn of
f audio output,
press again to resume volume level.
3. SOURCE Button
Press this button to change mode.
4. EQ Button
Press this button to choose POPROCK MET
AL
EQ off.
5. SEEK+ ( )/ SEEK-( ) Button
Press this button to manual turning, sped or quick back, previous song and next song.
6. VOL+ ( ) / VOL- ( )
Press this button to increase or decrease volume level.
7. SEL Button
Press this button to choose sound feature.
8. LOUD Button
Press this button to startup LOUD function.
9. BAND-P/N Button
In radio mode, press this button to choose band. In VCDDVD mode, press this button to choose PALAUTO or NTSC system.
10. LOC/RDM Button
In radio mode, press this button to switch between local and direction. In VCDCD mode, press this key to randomly play.
11. STOP Button
Press this button to stop playing.
12. PLAY/PAUSE Button
Press this button to switch between play and pause. In stop mode, press this button to play.
13. ST/PROG Button
In radio mode, press this button to choose stereo or mono station. In audio mode, it can help STOP button to programmed play.
Touch screen Calibration
NAVI
POWER ON/OFF
MUTE
SOURCE
EQ
SEEK+ / SEEK-
VOL+ / VOL-
SEL
LOUD
BAND / P
/ N
LOC / RDM
ST
OP
PLAY / PAUSE
ST / PROG
0-10+
AMS / RPT
TITLE
AUDIO
GO
T
O
SUBTITLE
PBC
UP / DOWN / L / R ENTER
SLOW
ANGLE
SETUP
OSD
ZOOM
MENU
Page 6
INSTRUCTIONS
14. 0-10+ Button
Press this button to choose desired song sectionpreset stations. Decimal numbers, for example the 19th song, press 10+ and 9 button.
15.
AMS / RPT Button
In radio mode, press this button to browse stored stations. In audio mode, press this button to play repeatedly
.
16. TITLE Button
In DVD mode, press this button to play back to the top menu of disc.
17. AUDIO Button
In DVD mode, press this button to switch language of dialogue. In VCD mode, press this button to choose left trackright track and stereo.
18. GO TO Button
In DVD mode, press this button, you can define playing time.
19. SUBTITLE Button
In DVD mode, press this button to switch language of subtitle.
20. PBC Button
In VCD mode, press this button to display all song menus, work with number button to choose songs.
21. UPDOWNLEFT RIGHTENTER Button
In DVD mode, press this button to move cursor up, down, left, right to choose item in menu, press the enter button to confirm choice.
22. SLOW Button
In audio mode, press this button to slow backward and slow forward.
23. ANGLE Button
In DVD mode, press this button to change play angle.
24. SETUP
Button
In audio mode, press this button to choose different set items.
25. OSD Display
Press this button to display the title chapter and the left time.
26. ZOOM Button
In DVD/VCD mode, press this button to ZOOM in.
27. MENU Button
Press button to back to the main menu.
28. NAVI Button
Press the button to enter/exit the navigation interface.
BATTERY CHANGE
When control distance of remote control becomes shorter or no function, please change battery. Please confirm polarity before change.
One hand press stopper, then pull out battery.
Put battery into controller.
Insert battery holder into controller.
into the General set interface. (Password: 888888). General settings have been set at the factory.
In the set interface click [GENERAL] icon,
Slide up and down to select your preferred language mode.
Language setting
In the General Settings screen, click [LANGUAGE] icon to enter the Language setting interface, as shown below:
Regional radio
In the General Settings screen, click [RADIO] icon to enter the Radio setting interface, as shown below:
Select your desired area.
Car Set setting
In the General Settings screen, click [Car Set] icon to enter the agreement setting interface, as shown below:
Y
ou will need to set protocol, click the
icon to confirm the save the settings.
Version Information
In the General Settings screen, click [VERSION] icon to enter the V
ersion
Information interface, as shown below:
The version information is displayed please prevail in kind.
System setting
In the General Settings screen, click [SYSTEM] icon to enter the System setting interface, as shown below:
You can choose the system settings interface has the feature is turned on or of
f.
General Settings
Page 7
Turn on/off
Navigation setting
Navigation path has been set at the factory, please do not enter the navigation setup interface to change the path freely
, otherwise the procedure many lead to abnormal navigation.
Audio setting
In the set interface click [AUDIO] icon, into the Audio set interface.
Click into sound effect default interface. Press into loudspeaker interface, click to adjust the channel of loudspeaker
, touch to get
back to initial setting.
BEEP: click that icon to switch on/off that. LOUD: click that icon to switch on/off that. GPS. MIX: click that icon to switch on/off that. EQ: click that icon to switch different mode.
Click on the main screen [Setup] icon, enter the setting interface. With a finger or touching pen to gently sliding screen can be set about switching interface.
Access setup interface
Video setting
In the set interface click [VIDEO] icon, into the video set interface.
Brightness: Drag icon can adjust video the screen brightness. Forbid play on run: Driving ban and click on play icon can open/close the function.
Time setting
Click the Settings interface T
ime setting icon, enter the Time settings screen, 12h/24h interchangeable, as shown below:
In the year, month, day
, hour, sub-office slide up and down to the relevant settings. Zone is set to enter the time zone settings interface when clicked. Choose the time zone, click the icon to save your settings and exit the time setting interface.
SET COMM setting
In the set interface click [SET COMM] icon, into the Serial port set interface.
Choose good then click the icon to save your settings and exit the serial port settings interface.
Touch calibration
If touch calibration error occurs, you can adjust the touch coordinate by “T
ouch calibration”. Click [CALIBRATION] icon on setup interface, click OK to pop up a [Do you want to calibration?] as shown below, click OK to confirm to access touch calibration interface:
Touching methods
Use touch pen to click the center of”+” icon, and move along with center of “+” icon so as to calibrate the screen, It shall automatically save data and exit after screen calibration. Please accurately click all positions on screen, or the accuracy of touch calibration shall be affected.
Basic operation setup menu
When the ignition switch is put in ACC or ON position, Press [ ] button on the front panel to turn on the unit.
After the host starts, hold [ ] button for 3 seconds , the host
will turn off.
Wallpaper and Logo Setup
Click on the main interface [wallpaper] icon into the wallpaper and boot screen settings interface, you can choose your favorite wallpaper and boot screen. Note: The start-up screen has been set at the factory.
Access main interface
In boot-up state, press [ ] button on the panel to switch to main interface, as shown in below picture:
1.
2.
Touch in different interface style to switch between. Press and hold the hide icon hold to the left and right drag, you can hide the
location of the icon to the left or right.
3. Click the icon or gently with a touch pen or finger to the left and sliding screen to toggle the main menu page.
4. To reset the shortcuts with a touch pen or finger to hold down the icon to drag the icon to drag the icon to the shortcut bar to the bottom of the screen, move over the icon will replace the old icon. If you want to delete the shortcut icon, first press and hold the icon until the trash can icon and then drag to the trash.
5. The icon at the touch on the main interface to switch between day, night and off-screen three modes.
6. Touch the function icons so as to access the corresponding function operations.
7. Double-click the watch icon to enter the clock setting interface: Click the icon to select your favorite type of clock. Click the icon unlock unlocked drag minutes to set the time, set up and click again to icon to lock the clock.
Page 8
Radio Operation
In tune
Among tall buildings At the boulevard The antenna is sheltered Underground parking Overpass or viaduct
GPS Operation
1. Navigation Function Operation For detailed operation of navigation function, see “Navigation Operation Manual”.
2. Receiving signal error
When the satellite signals can be normally received, the error of standard GPS shall be about 7 meters. Driving on parallel sections, there shall be error even the product has auto-correct function.
The normal receiving of satellite signals shall be af
fected
and cause error in following environment:
3. Satellite receiver
Navigation system can keep receiving eight satellite signals. As a general rule, the navigation system can figure out your accurate location after received 3-4 satellite signals. But sometimes, weather and tall buildings in the city shall affect the signal receiving ef
fect.
Scope for receiving satellite signals
Angle of elvevation
Angle of elvevation
Other Operation
Rear view function
In any running state, the video signal can switch to reverse video state when reversing the car
, and the system shall return to its initial running sta
te after reversing the car.
Do not rely on CCD system completely, please make sure your car is safe by your eyes during driving.Back rearview system only assists in driving. As the distance range of rearview system is limited, completely relying on the rearview system during driving may cause accidents.
Reverse field simulation
Rearview backup image
Warning
1. Enter/exit
T
ouch [Radio] icon in the main interface to enter into the radio interface.
2. Operation stored radio
Each band can be stored six radio stations, radio stations can be stored directly click (P1-P6) choice, and will be displayed on the screen.
3. How to save radio stations Select a band, and then select a radio station. Press and hold button (P1-P6) to select the preset number will appear in the corresponding number button on the screen.
Touch [
5. Search/Save radio stations
Short touch the [ ] button, browse 1-6 sets of bits stored on the radio, Long touch the [ ] button to long-automatic station search, and the strongest radio signals P1-P6 are stored in the display position on the table.
6. Play radio station selection
Touch [ ] icon pop-up selection sets the keyboard input radio frequency selectable radio frequency spectrum or you can drag directly touch the icon to select a stored radio station.
Touch [ ] can enter icon spectrum interface. Double-click the spectrum can switch over the spectrum style.
8. RDS Function
RDS function provides series information (such as traffice information, name of station) , and can automatically switch to the station with stronger signal and carries the same program.
AF: touch the button to turn on/off AF mode. TA: touch the button to turn on/off TA mode. PTY: touch the button the screen displays program types, users can search station
according to program type. NOTE: If the unit does not have RDS function, it has no AF/TA/PTY function, Touch the corresponding icon had no effect.
Touch [ ] icon to return to main interface, and then touch other function icons so as to exit radio mode.
4. Band selection
] icon so as to switch among FM1, FM2, FM3, AM1, AM2 bands.
7. Other Functions
Touch [ ] icon to access sound setting interface. Touch [ ] icon so as to turn on/off loudness function.
Touch [ ] icon so as to turn on/off Long/Short-Range function. Touch [ ] icon to turn on/off stereo.
Sliding around
Page 9
MEDIA Operation
Play disc
Insert the disc into the disc slot with the printing surface up, system will detect the disc and automatically take it in to read and play.
Eject disc
(1) Click button on the panel to eject the disc. (2) If a disc has not been took away 15 seconds after it is eje
cted, system will automatically take in the disc but not play. Do not insert two discs or more.
2. DVD/VCD disc playback
During playback of disc, touch the middle lower area of the screen to pop up the touch menu, operate the touch menu to perform various playback controls.
3. CD Disc Playback
After a CD is inserted, system shall access disk reading state immediately. When there is a disk in the device, click [Disk] at the main interface so as to access disk reading state. After the disk being read out, system shall automatically play in sequence.
4. MP3/JPEG/MPEG4 disk playing
When the disk contains readable files, such as MP3/JPEG/MPEG4 files, it shall be automatically read out and played after slipping into DVD player. During playing, touch the screen area and the touch menu shall pop up. Operate the touch menu for playing.
5. Touch Menu Function Description
The disc read, touch area of the screen, pop-up touch menu. Operate a variety of playback controls the touch menu.
1. Play/eject disc
00:00:09 00:04:48
Compass
Calculator Operation
In the main interface touch [Calculator] icon, into the counter interface.
Operation
In the main interface touch [Compass] icon, into a compass interface.
Steering wheel setting
Click the settings interface [STEER] icon into the steering wheel settings interface. Steering steps: The original line of control of the vehicle side, the positive, the negative and machine side control line cathode, anode connection after connection: T
ouch [Reset] and press above the steering wheel buttons one by one, and record the appropriate sequence and function, touch [allocation].
Touch the desired distribution voltage value (such as: 2.00V).
select the appropriate settings (such as: volume +).completed the steering wheel buttons will display the corresponding function.After completing the settings, touch [OK] to save the settings.For the reset function, can touch [Reset] (the original settings will all be cleared), and repeat Step ② ~ Step for resetting.You can also choose to set a good model of the steering wheel.
Click the models select] icon pop-up model selection interface, select your car type click OK icon to save the settings.
External input operation
Connect the video input plug with external video input jack, and connect the audio input plug with external audio input jack. Touch [AUX-IN] icon on main interface to access external input interface. Click icon into the sound settings screen. Loudness on / of
f.
Connect to Media first, touch [Media] icon on main interface to access Media interface, as shown in below diagram.
Click icon return to a interface
Short press next Song Long press fast forward playback/rewind playback
previous Song/
Sound settings
Play/Pause
Loudness on/off
Back to the previous directory
Page up/down
Number Button
Random play
cycle play
Disc Operation
Page 10
INSTRUCTIONS BT Operation
PIC 2PIC 1 PIC 3
PIC 4
Previous song
PLAY/P
AUSE
next song
1. Enter/exit
T
ouch [BT] icon in the main interface to enter the BT
interface, as PIC 1:
Touch icon to exit BT interface.
2. Pair/link
To use BT hand-free function, make connection first, i.e. match the host with the BT mobile phone.
Operation methods:
Set the host to be matching state, and open the BT of your mobile phone and use the mobile phone to search device, the mobile phone shall prompt to match password with the BT when it has searched the BT device. Input BT password (0000) to the mobile phone and confirm. The mobile phone shall prompt whether authorize to this device, please select [Yes]. Phone and BT shall automatically connect within 20 seconds. Under any working mode, the host shall convert to BT state if there is an incoming call. And the host shall restore to current mode after hanging up.
When the BT device matches with this device, the connection status shall display , otherwise, it shall display .
3. Dialing
You can dial on mobile phone directly or input phone number through the number buttons on the screen, click to delete if there is input error. After input the phone number, click to make a call.
4. Call records
In the BT interface of click to access call records interface as PIC 2: Dialed numbers: Touch this button to check all the dialed phone numbers. Received calls: Touch this button to check all the phone numbers of received calls. Missed calls: Touch this button to check all the phone numbers of missed calls. Delete: Touch the button to delete a selected record. All Delete: Touch the button to delete all information in phone book.
5. Phone book
After the cellphone gets connected to the unit, you can read records in the phonebook of your cellphone and store information in the phonebook of the unit. In the BT interface of click to access Phonebook interface as PIC 3: Touch icon in the phonebook interface, the unit will automatically download phone numbers and put them in order.
6. BT Music
In the BT interface of click to access BT music interface as PIC 4:
Forward/Backward play
Click the button, forward/backward play
.
The previous/next song
The previous/next songClick the button, .
C
hannel conversion
Click Switchable channel the button, .
Back to R
oot Menu
Click the button the DVD state can return to the root menu of the disc, VCD state can enter the PBC menu and playback.
Access title
menu Press this button to return to title menu of the disk. Directly click menu bar at title menu interface for playing.
During VCD
playing, this function only works when PBC is off.
Repeat play In playing state, touch this button to start repeat play function: Chapter repeat Title repeat Entire disc repeat Off.
Language Selection T
ouch the button, can switch subtitle language.
Note: the need to support the subtitle language discs have this feature.
Number Button Click
the button, pop-up numeric keypad. By click the numeric keypad for direct selections
played.
USB/SD Card Operation
When there is a USB device/SD card connected, the unit can conduct the playback of audio/video/image files in the USB device/SD card.
Insert/Eject USB storage device
1. Connect a U disc recorded with media information to the unit by a USB connecting cable.
2. When there is a need to eject the USB device, exit the USB device playback screen first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit correctly until it is locked.
2.
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the unit has connected with a USB device or SD card, touch [USB] icon in the multimedia interface to enter into the external storage playback interface;
T
ouch [SD] icon to enter into the SD card playback interface. During playback, touch the top center area of the screen to pop up the touch menu, operate touch menu to perform various playback controls.
When pulling out the SD card, exit SD card playing state first, then press the SD card
and it shall pop up after unlocking.
Play
After SD card/USB removable device being read out, the operation methods are similar to disk operation methods.
Forward/Backward play
The next page menu
Play/Pause
Stop
The previous/next song
Volume button
Number Button
Repeat play
Back to Root Menu
Access title menu
Zoom in/out
Channel conversion Language Selection
Random play
Scanning
Eject disc
DVD Setup Menu
BOSS AUDIO CAR STEREOS CAR AUDIO SYSTEMS
Loading...