Boss BV7330 User Manual

User’s Manual

BV7330

IN-DASH DVD/MP3/CD AM/FM

RECEIVER WITH 3.2" (81mm)

WIDESCREEN TFT MONITOR

WITH USB AND SD MEMORY CARD PORTS

AND FRONT PANEL AV INPUT

BV7330

IN-DASH DVD/MP3/CD AM/FM RECEIVER WITH 3.2" (81mm) WIDESCREEN TFT MONITOR

WITH USB AND SD MEMORY CARD PORTS AND FRONT PANEL AV INPUT



iPod® is a trademark of Apple, Inc. registered in the U.S. and other countries.

tech support: www.bossaudio.com/support

-VOBS$PVSUt0YOBSE$"

BOSS Audio Systems

www.bossaudio.com

800.999.1236

Boss Audio Systems is not affiliated with Apple, Inc.

BV7330

OWNER’S MANUAL

Mobile Audio/Video System

y 3.2" TFT Monitor y DVD Player with Radio y Fold down detachable Panel y Memory Card Interface y USB Interface y AUX IN interface on the front panel y Parental Control y Remote Control

CONTENTS

SAFETY INFORMATION ................................................................... 3

DISC NOTES ..................................................................................... 5

INSTALLATION.................................................................................. 6

USING THE DETACHABLE FRONT PANEL .................................... 9

CONNECTIONS................................................................................. 10

LOCATIONS AND FUNCTION OF THE PLAYER............................. 11

LOCATIONS AND FUNCTION OF THE REMOTE CONTROL......... 12

OPERATION...................................................................................... 15

BASIC OPERATION....................................................................................... 15

DVD OPERATION............................................................................................ 16

USB PLAY OPERATION.................................................................................. 21

MEMORY CARD OPERATION........................................................................ 22

RADIO OPERATION ........................................................................................ 22

AUX IN OPERATION........................................................................................ 23

TROUBLE SHOOTING...................................................................... 24

SPECIFICATIONS ............................................................................. 26



Features

Compatible with PAL DVD (Video CD) and NTSC DVD (Video CD)

This player can play discs recorded in either PAL or NTSC format.

z L/R stereo analog audio outputs for

connection to existing head unit aux inputs. Video output is composite video.

z Supplied remote handles

multi-function software (multi-language audio-track/subtitle, multi-angle, etc.), plus all basic functions.

 Use This Product Safely

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following procedures for installation, use and servicing. This unit doesn’t contain any parts that can be repaired by the user.

When Driving

Keep the volume level low enough to be aware of road and traffic conditions. When Car Washing Do not expose the product to water or excessive moisture. This could cause electrical shorts, fire or other damage. When Parked Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to

Use the Proper Power Supply This product is designed to operate with a 12 volt DC, negative ground battery system. Protect the Disc Mechanism Avoid inserting any foreign objects into the slot of this player. Failure to observe this may cause malfunction due to the precise mechanism of this unit. Use Authorized Service Centers Do not attempt to disassemble or adjust this precision product. Please refer to the Service Center list included with this product for service assistance. For Installation The unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30

cool down before starting playback.

SAFETY INFORMATION

CAUTION:

MOBILE DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS MOBILE DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE MOBILE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND - DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

y TO REDUCE THE RISK OF FIRE OR

ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

y TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

y THIS DEVICE IS INTENDED FOR

CONTINUOUS OPERATION.

Region Management Information

Region Management Information: This Mobile DVD Player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this Mobile DVD Player, this Mobile DVD Player cannot play this disc.

DISC NOTES

Handling and Cleaning

y Dirt, dust, scratches and warping discs

will cause wrong operation.

y Do not place stickers or make

scratches on discs.

y Do not warp discs. y A disc should always be kept in its case

when not in use to prevent from damage.

y Do not place discs in the following

places:

1. Direct sunlight.

2. Dirty, dusty and damp areas.

3. Near car heaters.

4. On the seats or dashboard.

Disc Cleaning

Use a dry soft cloth to wipe the surface. If the disc is quite dirty, using a soft cloth slightly dip with isopropyl (rubbing) alcohol. Never use solvents such as benzine, thinner or conventional record cleaners as they may mar the surface of the disc.



Preparing New Discs with Rough Spots

A new disc may have rough edges on its inside and outside edges. If a disc with rough edges is used, the proper setting will not be performed and the player will not play the disc. Therefore, remove the rough edges in advance by

Note:

A disc may become somewhat scratched (although not enough to make it unusable) depending on the way it is handled and conditions in the usage environment. Note these scratches are not an indication of any problem with the player.

using a ballpoint pen or pencil as shown on the right. To remove the rough edges, press the side of the pen or pencil against the inside and outside edges of the disc.

INSTALLATION

Notes:

y Choose the mounting location where

the unit will not interfere with the normal driving function of the driver.

y Before finally installing the unit,

connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.

y Use only the parts included with the

unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

y Consult with your nearest dealer if

installation requires the drilling of holes or other modifications of the vehicle.

y Install the unit where it does not get in

the driver’s way and cannot injure the passenger.

y If installation angel exceeds 30°from

horizontal, the unit might not give its optimum performance.

y Avoid installing the unit where it would

be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

T AKE OUT SCREW BEFORE INST ALLA TION

Before Installing the unit, please remove the two screws.

Take out screw before installation.

DIN FRONT-MOUNT (Method A)

Installation Opening This unit can be installed in any dashboard having an opening as shown below:

Installing the unit Be sure you test all connections first, and then follow these steps to install the unit.

1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the antenna.

3. Press the release button on the front panel and remove the control panel (see the steps of “removing the front panel”).

4. Lift the top of the outer trim ring then pull it out to remove it.

5. The two supplied keys release tabs inside the unit’s sleeve so you can remove it. Insert the keys as far as

INSTALLATION

they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit.

(1) Front Panel; (2) Outer Trim Ring; (3) Sleeve; (4) L key; (5) R key.

6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place.

(1) Dashboard (2) Taps

7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.

8. Slide the unit into the sleeve until it locks into place.

9. To further secure the unit, use the supplied metal strap to secure the

back of the unit in place. Use the

supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle’s mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. Note to install the short threading

terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard.

(1) Metal Strap; (2) Mounting Bolt; (3) Hex Nut; (4) Spring Washer; (5) Tapping Screw; (6) Plain Washer

10. Reconnect the cable to the vehicle battery’s negative (-) terminal. Then replace the outer trim ring and install the unit’s front panel (see the steps of “installing the front panel”).

Removing the unit

1. Make sure the ignition is turned off, then

disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Remove the metal strap attached the

back of the unit (if attached).

INSTALLATION

3. Press the release button to remove the front panel.

4. Lift the top of the outer trim ring then pull it out to remove it.

5. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard.

DIN REAR-MOUNT (Method B)

If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.

To fasten the unit to the factory radio mounting brackets. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side.

Note: the outer trim ring, sleeve and the metal strap are not used for method B installation.

Factory Radio Mounting Bracket

Screw

Side View showing Screw Holes marked T, N

Dashboard or Console

Screw

+ 18 hidden pages