Acoustic Wave®Multi-Disc Changer
2ZQHU·V*XLGH
Safety Information
WARNING: To reduce the risk of fire or electric shock, do not expose the Acoustic
®
Wave
multi-disc changer to rain or moisture. The apparatus shall not be exposed to
dripping or splashing, and objects filled with liquids, such as vases, shall not be
placed on the apparatus.
As with any electronic product, use care not to spill liquids into any part of the multidisc changer. Liquids can cause a failure and/or a fire hazard.
C
D
P
L
A
Y
/
P
A
U
S
E
S
T
O
P
R
A
N
S
D
K
O
I
M
P
/
S
C
R
A
E
N
P
E
A
T
A
C
O
U
S
T
I
C
1
W
A
V
P
E
R
®
E
S
MU
E
T
S
S
I
2
C
S
Y
S
T
EM
3
1
4
F
M
5
VO
L
U
M
E
A
M
1
‹
A
U
X
›
O
S
N
E
/
E
O
K
F
/
F
T
U
N
E
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISQUE DE CHOC ÉLECTRIQUE
ATTENTION : POUR RÉDUIRE LE RISQUE DE DÉCHARGE
ÉLECTRIQUE, NE RETIREZ PAS LE COUVERCLE (OU
L’ARRIÈRE). IL NE SE TROUVE ÀL’INTÉRIEURAUCUNE
PIÈCE POUVANT ÊTRE RÉPARÉE PARL’USAGER.
S’ADRESSER À UN RÉPARATEUR COMPÉTENT.
AV I S
NE PAS OUVRIR
These CAUTION marks are located on the bottom of your CD changer:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the
user to the presence of important operating and maintenance instructions in this owner’s guide.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, insert fully.
WARNING: No naked flame sources, such as lighted candles, should be placed on the apparatus.
Note: DO NOT place the multi-disc changer on any heat-sensitive surface, such as the finished surface of fine
furniture. Like all electrical equipment, it generates some heat.
Class 1 Laser Product
This CD changer is classified as a CLASS 1 LASER PRODUCT according to
EN 60825-1:1994 + A11. The CLASS 1 LASER PRODUCT label is located on
the bottom of the system.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LOUKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
WARNING: Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure. The multi-disc player should not be adjusted or
repaired by anyone except properly qualified service personnel.
Note: The CD changer is designed for use with an Acoustic Wave
®
music system.
Batteries
Batteries
Please dispose of used batteries properly, following any local regulations. Do not incinerate.
WARNING: Mishandling the remote control battery may cause a fire or chemical burn. Keep
the battery away from children. Do not recharge, disassemble, heat above 212˚F (100˚C), or
incinerate the battery. Dispose of the used battery promptly and responsibly.
Please read this owner’s guide
Please take the time to follow this owner’s guide carefully. It will help you set up and operate your Acoustic Wave
multi-disc changer properly, and enjoy all of its advanced features. Save your owner’s guide for future reference.
©1994-2003 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior
written permission. All trademarks referenced herein are the property of Bose Corporation. The Acoustic Wave
tem design is a trademark of Bose Corporation.
2
®
®
music sys-
Contents
Setting Up Your Multi-Disc Changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Benefits of the multi-disc changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking the carton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Selecting a location for your music system and changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Seating your Acoustic Wave
Connecting the multi-disc changer to your Acoustic Wave
Using Your Acoustic Wave
Operating with one remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Turning your complete system on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Loading/unloading discs into the multi-disc changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Two display panels, two sets of information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Playing the multi-disc changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Playing the other sound sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Controlling both units as a complete system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adding External Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting other sound sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Choose the component(s) you want to connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Making the power connection last . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Playing an auxiliary component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Maintaining Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Replacing the remote control battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Bose Corporation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
®
music system on the multi-disc changer . . . . . . . . . . . . . . . . . . 5
®
Multi-Disc Changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
®
music system . . . . . . . . . . . . . . . 6
For your records
The serial number for the Acoustic Wave® multi-disc changer is located on the back panel.
Changer serial number:
Purchase date:
We suggest you keep your sales receipt together with this owner’s guide.
3
Setting Up Your Multi-Disc Changer
Before you begin...
Thank you for selecting the Bose®Acoustic Wave®multi-disc changer, designed as an acces-
sory for the Acoustic Wave
needs, the changer also provides an attractive pedestal for the system and a connection hub
for auxiliary components.
Choosing the convenient option of connecting other sound sources to the changer allows
you to enjoy the full impact of their sound through your Acoustic Wave
Benefits of the multi-disc changer
• Hours of uninterrupted CD play
• New multi-disc remote control, that provides simplified, all-in-one system operation
• One button press turns on the changer, FM or AM radio or CD, or selects an auxiliary component
• Compact design that complements the lines of your Acoustic Wave
• Option of hearing auxiliary audio sources through your Acoustic Wave
• Quality construction and performance
Unpacking the carton
Carefully unpack your Acoustic Wave® music system multi-disc changer. Save all packing
materials for possible future use. The original packing materials provide the safest way to
transport your new multi-disc changer.
Check to be sure you received the parts identified in Figure 1. If any part of the product
appears damaged, do not attempt to use it. Notify Bose customer service immediately (see
phone numbers on the inside back cover).
Note: Now is a good time to locate the serial number on the back of your multi-disc changer,
then write it in the space provided on page 3.
®
music system. As a high-quality solution for your multi-disc
®
music system.
®
music system
®
music system
Figure 1
Contents of carton
• Acoustic Wave
multi-disc changer
• Remote control
• Power cord
• Quick setup guide
®
Acoustic Wave
multi-disc changer
Power cord
Remote control
®
F
F
/O
ON
dom
an
R
ext Disc
N
top
S
X 2
U
A
se
lay/Pau
1
P
X
U
A
Quick setup guide
4
Setting Up
Selecting a location for your music system and changer
The Acoustic Wave® multi-disc changer is designed to fit right under your Acoustic Wave
music system. Before you connect the two, however, select a good location for the stacked
units.
CAUTION: Setting up the two units separately (on different shelves of an entertainment center, for example) is not recommended. Doing so will prevent proper communication between
the two and will adversely affect operation.
When choosing the location, remember that the tonal quality of your Acoustic Wave
system, as with any high-performance sound system, will vary with room placement.
Feel free to try different locations, but keep in mind that…
• The Acoustic Wave
®
music system is designed to sound best when placed on a shelf,
counter, desk, or table top, 30 to 48 inches (75-120 cm) from the floor.
• The CD player in the Acoustic Wave
®
music system needs an allowance of several inches
for the CD cover on top of the music system to open.
• The music system should be near the horizontal center of a wall and 6 inches (15 cm) or
less from the surface behind it.
• To increase the bass response, move the unit toward any corner of the room; to decrease
bass response, move it away from the corner.
Seating your Acoustic Wave® music system on the multi-disc changer
®
music
®
Figure 2
Seating the Acoustic Wave
music system (a) on top
of the multi-disc changer,
so (b) it sits flat and the two
units communicate
1. Place the multi-disc changer in the location you have chosen, following the guidelines
above.
2. Carefully seat your Acoustic Wave
®
music system on top of the changer (Figure 2a). Make
sure that it sits flat and the side edges of both units are aligned (Figure 2b).
Note: The music system slips onto raised guides on top of the changer.
(a)
TM
®
P
l
a
y
/
P
a
u
s
e
A
St
U
X
o
p
1A
U
X
2
N
e
x
t
D
i
s
c
R
a
n
d
o
m
O
N
/
O
F
F
IR signal
receivers
Raised
guides
(b)
C
D
P
L
A
Y
/P
A
U
S
E
S
T
O
P
S
K
IP
/
S
C
A
N
A
U
X
1
AU
X
2
P
l
a
y
/P
au
s
e
S
to
p
IR signal
emitters
R
A
N
DO
R
E
M
P
E
A
T
A
C
O
U
S
T
I
C
W
A
V
E
®
M
U
S
I
C
S
Y
S
T
E
M
S
k
ip
/S
c
a
n
N
e
x
t Dis
c
R
a
n
d
O
o
m
N
/
O
F
F
1
1
V
2
OL
P
UM
RE
E
S
1
E
F
T
M
S
3
A
U
A
X
M
4
O
N
/
OF
‹
F
5
S
E
E
K
/T
›
U
N
E
In alignment
CAUTION: Maintaining a clear optical path between the multi-disc changer and the music
system, shown in Figure 2(b), is important. When the changer is turned on, it sends infrared
(IR) signals that also turn on the music system. If those signals are blocked, there may be no
sound when the changer is playing.
5
Setting Up
Connecting the multi-disc changer to your Acoustic Wave
®
music system
Figure 3
Connecting the multi-disc
changer to the Acoustic
®
music system
Wave
On the back of the multi-disc changer there are two cables (Figure 3) that connect to your
Acoustic Wave
®
music system.
1. Insert the two connectors of the AUX input cable into AUX IN jacks on the back of the
Acoustic Wave
®
music system. Be sure to match the colors of the connectors and jacks:
red to red, and white to white.
2. Insert the plug of the AC power cable into the AC power receptacle on the back of the
®
Acoustic Wave
music system.
TM
Figure 4
Plugging in the power cord
Power jack
Note: The changer comes supplied with a detachable power cord, similar to the one provided
with the Acoustic Wave
AC power cable
®
music system. You will need to use only one of these two supplied
AUX input cable
power cords.
3. Plug the small end of the detachable power cord into the power jack on the back of the
changer (Figure 4).
CAUTION: If you will be connecting auxiliary components to the changer, refer to “Connecting other sound sources” on page 13.
4. Plug the other end of the power cord into an AC (mains) wall outlet and your setup is
complete.
Note: When the multi-disc changer turns on after you plug it in, “PLEASE WAIT” flashes on its
display for a few seconds. When the flashing stops, you can load and play the changer.
6
Using Your Acoustic Wave® Multi-Disc Changer
M
Operating with one remote control
Figure 5
A new remote with
combined controls
The remote control included with your Acoustic Wave® multi-disc changer allows you to control functions of both the multi-disc changer and your Acoustic Wave
fore, we suggest you put away the remote that came with your Acoustic Wave
system and use only this Acoustic Wave
Notice that this remote (Figure 5) has buttons to play the multi-disc changer, the Acoustic
®
Wave
music system, and to select other external components connected to the changer.
Note: The Acoustic Wave
®
multi-disc changer remote can select an auxiliary component that
®
multi-disc changer remote.
®
music system. There-
®
music
is connected to the changer, but cannot turn the component on or off or change its settings.
Turn Acoustic Wave
music system on or off
Adjust volume
®
Seek/Tune, when tuned
to FM or AM
Skip/Scan, when set
to CD or CD changer
Select:
PRESET radio station,
when tuned to FM or A
CD (1 through 5) when
system is set to CD
changer
Turn on the system and play
the appropriate sound source
Play/Pause for single CD player
(on top of the Acoustic Wave
music system)
Play/Pause for multi-disc changer
®
STOP for CD changer
single CD player
and
Next disc selection
for multi-disc changer
Note: If the remote stops operating or its range seems reduced, it may be time to replace the
battery. However, be aware that a change in room lighting or other conditions, in addition to
battery age, can affect the operating range of an infrared remote control.
For instructions on battery replacement, refer to “Replacing the remote control battery” on
page 15.
7
Using Your Acoustic Wave® Multi-Disc Changer
Turning your complete system on and off
To turn on both the changer and the Acoustic Wave®music system, press the Play/Pause
button (Figure 6) on the changer console.
Figure 6
Play/Pause button on the
Acoustic Wave
changer console that turns
on both the changer and
the Acoustic Wave
system
®
multi-disc
®
music
Play/Pause
AUX 1 AUX 2
Play/Pause Stop Next Disc Random
ON/OFF
This turns on both units, so the multi-disc changer is ready to play.
• To turn on only the Acoustic Wave
®
music system to its last played sound source, press
the On/Off key on the new remote control or on the console of the Acoustic Wave
system.
To turn off both the Acoustic Wave
®
multi-disc changer and the Acoustic Wave® music
system, press the On/Off key on the remote control.
• To turn off only the changer, press the On/Off key on the changer console.
Loading/unloading discs into the multi-disc changer
CAUTION: Do not attempt to load more than one CD in any of the slots. Doing so can cause
the discs to jam and be damaged.
®
The Acoustic Wave
installed, the display indicates the number of the CD selected, the track it is playing, and the
elapsed time.
1. To insert a CD into the changer, slip one edge of the disc into an empty slot and press
on the opposite edge until the disc is all the way in (Figure 7 on page 9).
The LEDs on the front of the unit turn color as follows:
• No light indicates that the slot is empty.
• Orange light indicates that the slot is loaded with a CD.
This light flashes during ejection of the disc.
• Green light indicates that the CD in that slot is playing.
This light flashes while the changer is switching to that disc.
multi-disc changer holds up to five CDs. When it is on and a CD is
®
music
8
Using Your Acoustic Wave® Multi-Disc Changer
Figure 7
Inserting a disc into the CD
changer
Figure 8
Console displays (a) and
LEDs (b) indicating a CD on
the changer is playing
C
D
P
L
A
Y/
P
A
U
S
E
S
T
O
P
S
KI
P
/
S
C
A
N
R
A
ND
R
O
E
M
P
E
A
T
A
C
O
U
S
T
I
C
WA
V
E
®
M
U
S
IC
S
Y
S
T
E
M
1
1
V
2
O
L
U
M
E
1
F
M
A
U
A
X
M
O
N
/
O
F
F
TM
PR
E
S
E
T
S
3
4
‹
5
S
E
E
K/
T
›
U
N
E
LED indicators
Eject
A
U
X
1
A
U
X
2
Pl
a
y
/
Pa
u
s
e
S
t
o
p
S
k
i
p
/
S
c
a
n
Ne
x
t
D
i
s
c
R
a
n
d
O
o
m
N
/
O
F
F
E
j
e
c
t
1
2
3
4
5
1
2
3
4
5
Green light indicates
the slot is in use
after the CD is inserted
Note: To keep track of the order of CDs in the slots, you may find it useful to keep the CD
cases stacked in the same order near the multi-disc changer.
To hear the CD you have just inserted, press the Play/Pause button on the console.
To remove a CD from a changer slot, press the button to the right of the LED for that slot.
Allow a few seconds for the mechanism to respond.
Two display panels, two sets of information
When the two units first turn on, displays on both consoles light up (Figure 8a). The Acoustic
®
music system displays AUX to show that the CD changer or one of the components
Wave
connected to it is selected. It also shows the volume setting. The Acoustic Wave
changer display indicates what is playing on the changer. LEDs next to the CD slots on the
front of the changer light up as CDs are installed (Figure 8b).
(a)
Acoustic Wave
CD Play/Pause Stop Skip/Scan CD Mode
®
music system display
AUX
VOLUME
Presets
12345
FM AM
Acoustic Wave Music System
Volume
AUX
On/Off
AUX indicator
Seek/Tune
®
multi-disc
®
Acoustic Wave
Disc selected
Track playing
(b)
Acoustic Wave
multi-disc changer display
TRACK
DISC
AUX 1 AUX 2
CHANGER
Play/Pause Stop Next Disc CD Mode
®
multi-disc changer front panel
ON/OFF
CD play
Elapsed time
CD indicator LED
Eject
1
2
3
4
5
What else the displays tell you
®
The display on the Acoustic Wave
music system shows when one of its sound sources is
selected. It also displays the number – 1 to 100 – of the volume setting. When the single CD
player is in use, it shows the track number and the elapsed playing time.
When the multi-disc changer is playing, its display shows which disc and track are playing
and the elapsed time.
9
Using Your Acoustic Wave® Multi-Disc Changer
ac / u e
Playing the multi-disc changer
Use buttons on the multi-disc changer remote or console, as shown below.
AUX 1 AUX 2
Play/Pause Stop Next Disc CD Mode
Function
To play the selected CD.............................
Results:
Remote control Changer console
Changer
Play/Pause
• If there is no CD in the slot, the word
“DISC” flashes on the multi-disc changer
display.
• If there is a disc, the display shows the
current track playing and elapsed play
time.
Press again to pause.
To pause the disc while it is playing.........
Press again to resume play.
Changer
Play/Pause
To stop the CD............................................
Results: In the display window, the CD and
track number still appear, while the elapsed
Stop
time returns to zero.
To mute the CD........................................... Not available
ON/OFF
To skip tracks on a CD...............................
Results: The display shows the new track
number and elapsed time.
To scan through a track.............................
Press and hold to scan backward or forward . Continue holding to scan the next
or previous track(s).
To move to the next disc...........................
Results: CD number on the display
changes; LED next to the slot of the newly
selected CD flashes green, then stays lit.
To select a specific CD by number.............
Results: The CD in that numbered slot
begins to play.
Track / Tune
(Press and Hold) (Press and Hold)
Next Disc
Not available
10
Using Your Acoustic Wave® Multi-Disc Changer
Function
To change the mode of CD play................
Press again to cycle through the choices,
which appear on the console display.
• REPEAT ALL
• REPEAT ALL RANDOM
• REPEAT DISC
• REPEAT DISC RANDOM
Playing the other sound sources
The light blue buttons (Figure 9) on the multi-disc changer remote turn on the Acoustic Wave
music system and select a sound source. Those buttons include FM, AM, AUX1, AUX2, and
CD (for the single-disc player in the Acoustic Wave
To turn on auxiliary components connected to the multi-disc changer, use the power button
on the component console or the remote control that came with the component.
Note: AUX1 and AUX2 buttons play an auxiliary component only if one is connected to the
AUX1 or 2 jacks on the rear of the Acoustic Wave
AUX 1 AUX 2
Play/Pause Stop Next Disc CD Mode
ON/OFF
Remote control Changer console
Not available
CD Mode
®
music system).
®
multi-disc changer.
®
Figure 9
Blue buttons on the
multi-disc changer remote
control
Use the remote control, the multi-disc changer control panel or the Acoustic Wave®music
system control panel – whichever is most convenient – to operate the changer and the other
sound sources.
11
Using Your Acoustic Wave® Multi-Disc Changer
Controlling both units as a complete system
The Acoustic Wave®multi-disc remote control can change some of the Acoustic Wave®music
system settings and select and play its sources, as well as operating the changer functions.
Note: For details on how the Acoustic Wave
able for controlling it, refer to the owner’s guide that came in the carton with the system.
Function Remote control Changer console System control panel
®
music system functions and the options avail-
Volume
AUX 1 AUX 2
Play/Pause Stop Next Disc CD Mode
ON/OFF
CD Play/Pause Stop Skip/Scan CD Mode
Acoustic Wave Music System
AUX
VOLUME
Presets
12345
FM AM
AUX
On/Off
Seek/Tune
To turn on the Acoustic Wave
®
music
system to its last source played................
On
Off
Not available
On/Off
(NOT the CD changer)
To turn on and select the CD changer...... Not available
To change mode of single CD play.........
To set radio presets....................................
(with the radio station selected)
Changer
Play/Pause
Not available Not available
Not available
CD Mode
Presets
123 45
Press and hold down the button that you
want to assign to the selected station.
Results: A brief beep registers your setting.
To tune to a preset radio station...............
(with the radio on)
To play an auxiliary component.................
)LUVWWXUQRQWKHSRZHUIRUWKDWFRPSR
AUX1
or
Play/Pause
AUX2
Not available
AUX 2
Or
123 45
Presets
Not available
AUX 1
QHQWE\SUHVVLQJWKH3RZHUEXWWRQRQLWV
UHPRWHRUFRQVROH
7DNHQRWHRIZKHWKHUWKHFRPSRQHQWLV
FRQQHFWHGWRWKH$8;RU$8;MDFNVRQ
WKHEDFNRIWKHFKDQJHU
7KHQSUHVVWKHDSSURSULDWHEXWWRQ
12
Connecting other sound sources
This new changer provides a hub for other component connections.
CAUTION: Before connecting additional components, and to protect your components from
damage, be sure to unplug the multi-disc changer from the AC (mains) wall outlet if it is
plugged in.
Choose the component(s) you want to connect
Additional RCA input jacks allow you to connect other audio or video components to the
multi-disc changer. This gives you the advantage of hearing Acoustic Wave
sound from a range of sources. They can include a TV, VCR, cassette player, or DVD player,
for example.
Note: To connect an Acoustic Wave
Acoustic Wave
microphone.
Steps for adding other components:
Use the RCA cable supplied with the component.
Note: If your component is mono, or does not include an RCA output cable, you may need to
purchase an adaptor. Call Bose
1. Insert both connectors at one end of that cable into AUDIO OUT jacks on the rear of the
component (Figure 10).
2. Insert both connectors at the other end of the cable into one pair of AUX jacks on the
multi-disc changer.
CAUTION: Be sure to match the red plug to the red jack.
Repeat steps 1 and 2 for any other components you want to connect.
®
music system. The multi-disc changer is not designed for use with a
Using External Components
®
music system
®
microphone, use the MIC jack on the rear of the
®
Product and Technical Services,1-800-367-4008, for details.
Figure 10
Connecting additional
components
TM
L
R
Auxiliary component
13
Using external components
Special requirement for adding a turntable
To connect a turntable, you need to first connect a phono preamplifier (with RIAA equalization) to the changer.
1. Plug one end of the stereo audio cable into the output jacks of the preamplifier.
2. Plug the other end of the cable into one set of AUX IN jacks on your changer, matching
red to the red jack marked R (right) and black or white to the white jack marked L (left).
3. Plug the turntable cable into the preamplifier.
CAUTION: Be sure to match the red plug to the red jack. This ensures proper polarity of the
signal for an accurate balance of low-to-high frequencies.
Making the power connection last
When the additional components are connected, insert the multi-disc changer power plug
into an AC power outlet.
Playing an auxiliary component
Figure 11
Display of the Acoustic
®
multi-disc changer
Wave
when an auxiliary component is selected
Note: To play a component connected to the changer, you must first turn the component on.
Neither of the Bose
®
remote controls can turn an auxiliary component on or off, or change its
settings or selections.
With the component turned on, select it using the Acoustic Wave
®
multi-disc changer remote
control. Press the AUX1 or AUX2 button on the remote, as appropriate.
This turns on the changer and the Acoustic Wave
®
music system, so you can hear the
component sound played through the system.
Pressing AUX1 or AUX2 buttons on the changer console is another means of playing an
auxiliary component connected to it.
AUX
AUX 1 AUX 2
Play/Pause Stop Next Disc Random
ON/OFF
14
Replacing the remote control battery
If your remote control does not work properly, or its range of operation is reduced, it is time to
replace the battery. Follow the instructions below:
1. Place the remote control face down on a flat surface.
2. Press the tab lock on the battery compartment to the side, as shown (Figure 12a).
3. Hold that tab down as you slide the battery compartment open and remove the battery.
4. Install a new battery, making sure that the positive symbol (+) is facing up as you put the
battery into the compartment (Figure 12b).
Maintaining Your System
Figure 12
Pressing the (a) tab lock
down to remove the (b) battery compartment
(a)
(b)
Positive symbol
Tab
es of
See operating
battery to be used
instructions for types of
e used
ee operating
S
attery to b
b
instructions for typ
WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.
Replace only with a lithium CR2032 or DL2032 battery by Duracell, Eveready, Hitachi, Maxell,
or Toshiba (available from most electronics stores).
Mishandling the remote control battery may cause a fire or chemical burn. Keep the battery
away from children. Do not recharge, disassemble, heat above 212˚F (100˚C), or incinerate the
battery. Dispose of the used battery promptly and responsibly.
For more information, call Bose
®
customer service. Refer to the phone numbers on the inside
back cover of this guide.
15
Maintaining Your System
Troubleshooting
Problem What to do
No system operation
• Make sure the power cord for the Acoustic Wave
®
multi-disc changer is completely
plugged in both at the changer jack and at the wall outlet.
No sound or
sound is muffled
• If the Acoustic Wave
sure that AUX is displayed as the selection on the Acoustic Wave
®
multi-disc changer or a component connected to it is playing, make
®
music system display.
• If the sound source is an auxiliary component connected to the multi-disc changer,
make sure that component is plugged in and turned on.
• Make sure that both the Acoustic Wave
®
multi-disc changer and the Acoustic Wave
music system are plugged into functioning power outlets, and are turned on.
• Check the connection of the Acoustic Wave
two RCA connectors are firmly inserted, red to red, and white to white, into the AUX IN
jacks on the Acoustic Wave
to your Acoustic Wave
®
music system. Refer to “Connecting the multi-disc changer
®
music system” on page 6.
®
music system to the changer. Make sure the
• If the sound source is an auxiliary component connected to the multi-disc changer,
make sure the connections are fully and firmly inserted into jacks on both the changer
and on the component.
• Make sure nothing is blocking or preventing the IR signals emitted by the multi-disc
changer from reaching the receiver on the front of the Acoustic Wave
Refer to “Seating your Acoustic Wave
®
music system on the multi-disc changer” on
®
music system.
page 5.
CD skips • Does the unit get bumped in its current location? If so, move it to a more protected
location.
• Check the CD for smudges or dirt. Wipe the CD (NOT in a circular pattern, but straight out
from the center) to it clean off.
®
CD does not play • Make sure you have selected the changer or the CD player.
• If you have selected the changer, make sure AUX is the selection shown on the Acoustic
®
Wave
music system display. If it is not, press the AUX button on the music system
console.
• Make sure there is a CD is in the selected changer slot or in the CD player on the Acoustic
®
music system.
Wave
• Make sure CD is selected on the display of the Acoustic Wave
A CD is playing, but none
of the multi-disc changer
• Check to see if the CD player in the Acoustic Wave
instead of the changer.
®
music system is on and playing,
LEDs is lit
Customer Service
For additional help in solving problems, contact Bose®customer service. Refer to the address
list on the inside back cover of this guide.
®
music system.
16
Warranty
Maintaining Your System
What is covered:
All parts defective in material or workmanship.
For how long:
One year from the purchase date.
What we will do:
We will, at our sole option, repair or replace any defective parts free of charge.
What you must do:
A. Call Bose
B. Properly pack the unit, if possible, in the original carton for shipping.
Other conditions:
This warranty is fully transferable for the one-year period following purchase.
THE PROVISIONS OF THIS WARRANTY ARE IN LIEU OF ANY OTHER WARRANTY,
WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. BOSE CORPORATION’S
MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU
FOR THE PRODUCT. IN NO EVENT SHALL BOSE BE LIABLE FOR SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR INDIRECT DAMAGES.
This warranty does not cover a defect that has resulted from improper or unreasonable use or
maintenance, accident, improper packing, or unauthorized tampering, alteration, or modification as determined solely by us. This warranty is void if the label bearing the serial number
has been removed or defaced.
Other Legal Rights:
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state or country to country. Some places do not allow limitations on implied warranties or the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
®
Customer Service and ask for shipping instructions.
Technical Information
Multi-disc changer power rating
120V 50/60Hz 15W
In combination with the Acoustic Wave
Dimensions
31/4"H x 18"W x 83/8"D
(8.7 cm x 45.7 cm x 21.1 cm)
Weight
6.7 lb (3.1 kg)
Color
Graphite Gray or Platinum White
®
music system, 80W maximum
17
18
Bose Corporation
USA & Canada Sales
Bose Corporation, The Mountain
Framingham, MA 01701-9168
1-800-637-8781
USA & Canada Service
Bose Corporation, The Mountain
Framingham, MA 01701-9168
1-800-637-8781 or
508-879-7330, x63055
European Office
Bose Products B.V., Nijverheidstraat 8
1135 GE Edam, Nederland
TEL 0299-39011155 FAX 0299-390114
Australia
Bose Pty Limited
Unit 3/2 Holker Street
Newington NSW, 2127
TEL 612 8737 999955FAX 612 8737 9924
Deutschland
Postfach 1468
48504 Nordhorn
TEL 0800-2673555 55FAX 05921-724250
France
6, Rue Saint Vincent
78100 Saint Germain in Laye
TEL 01-3061 6363555FAX 01-3061 4105
Nederland
Bose B.V., Nijverheidstraat 8
1135 GE Edam, Nederland
TEL 0299-39011155 FAX 0299-390114
United Kingdom
Freepost EX 151
Exeter EX1 1ZY
TEL 0800 614 29355FAX 0870 240 2013
World Wide Web
www.bose.com
19
©2003 Bose Corporation
The Mountain, Framingham, MA
01701-9168 USA
270626 AM Rev. 01 JN30964
Loading...