Bosch VJC-7000-90 Specsheet
Video | VIDEOJET connect 7000
VIDEOJET connect 7000
www.boschsecurity.com
u Operates a variety of Bosch HD PTZ cameras,
including MIC7000
u Bi-directional audio, Alarms, washer pump control,
local storage slot for a CompactFlash (CF) memory
card, built-in web browser for control of connected
cameras
The device VIDEOJET connect 7000 (VJC-7000-90) is a
full-featured network power supply unit that can
operate a variety of Bosch PTZ cameras such as
MIC7000. The device includes one (1) HPoE network
connection, two (2) standard network interfaces for
connections to additional IP devices, one (1) slot for
an optional CompactFlash (CF) memory card, two (2)
slots for use with SFP-based fiber optic modules,
alarm/washer control interfaces*, and audio I/O*.
* Note: This feature is valid only for a MIC7000 camera
"bound" to Camera 1.
System overview
Notice
For full functionality, a MIC7000 camera
connected to VIDEOJET connect 7000 requires
firmware version 5.93 or later. Download the
firmware from
https://downloadstore.boschsecurity.com.
u One (1) HD-BaseT PoH dedicated for one RJ45
Ethernet port; three (3) RJ45 ports; two (2) SFP
ports
u Support for daisy-chaining of multiple cameras
Certifications and approvals
Electromagnetic
Compatibility (EMC)
Complies with FCC Part 15 Class A,
ICES-003, and CE regulations, including
latest versions of
EN 50130-4,
EN 55022:2010
EN 61000-3-3,
EN 61000-6-1, and
EN 61000-6-2
Product Safety Complies with UL, CE, CSA, EN, and IEC
Standards 60950-1 & 22
Ingress Protection
IP66, IP67, NEMA Type 4
Rating/
Standard
Note:
To achieve a distance of 100 m (328 ft) using
Cat5e/Cat6e cable, Bosch recommends using cable
with a minimum rating of 350 MHz.
Cat5e/Cat6e = 100 m max.
1
1
2 | VIDEOJET connect 7000
Installation/configuration notes
Basic configuration with VIDEOJET connect 7000
1 Ethernet (network) cable (Cat5e/Cat6e) (user-supplied) between a
Bosch camera and the port labeled PoE on VIDEOJET connect 7000
2 Data-only IP cable (Cat5e/Cat6e) to the head-end network
Note: The cable to the head-end also can be fiber optic cable from one
of the two SFP slots.
3 Alarm input / output interface cables (user-supplied)
4 Alarm output cables (user-supplied)
5 120 / 230 VAC, 50/60 Hz
6 Audio input / output interface cables (user-supplied)
7 External washer pump (user-supplied)
8 Washer output, 2-conductor (user-supplied)
Parts included
• One (1) VIDEOJET connect 7000 enclosure with three
(3) M16 plugs, three (3) ¾” blanking plugs, and five
(5) M16 gland locknuts installed
• Parts bag with:
– one (1) terminal plug connector, 2-pin [for
connections to optional washer]
– one (1) terminal plug connector, 3-pin [for AC
mains power input]
– one (1) terminal plug connector, 6-pin [for alarm
inputs]
– one (1) terminal plug connector, 7-pin [for alarm
outputs and for the supervised alarm input]
– three (3) watertight M16 cable glands with O-
rings
• Installation Manual
Network
Communication 3x 10BASE-T/100BASE-TX/1000Base-TX
If SFP fiber optic modules installed: 2x 1000
BASE-FX
SFP Modules
SFP (small formfactor pluggable)
Two (2) for use with SFP-based fiber optic
modules (1GB only) such as:
slot
• Agilent, SFP-GE-SX-MM850-A
HFBR5710LP 7
• Cisco, GLC-LH-SM 1300nm
• Cisco, GLC-SX-MM 850nm 8
• Finisar, FTLF8519P2BTL 850nm
Audio
- Standard G.711, 8 kHz sampling rate
L16, 16 kHz sampling rate
AAC, 16 kHz sampling rate
- Signal-to-Noise
>50 dB
Ratio
- Audio Streaming Bidirectional (full-duplex)
Storage
Local storage One (1) slot for optional CompactFlash (CF) memory
card, Type I / Type II, True IDE Mode, 1 TB max (usersupplied)
Miscellaneous
Washer
switch
Push button to activate/test the washer relay
momentarily
User Connections
Alarm Inputs Four (4) normal dry contacts (selectable N.O./N.C.)
Monitored supervised alarm input (Alarm 1), 2.2K
ohm (Ω) end-of-line terminating resistor
Alarm
Three (3) open collector outputs, 32 VDC, 150 mA
Outputs
Washer driver
Dry contact relay, 250 V, 5 A
output
RJ45
connectors
(3) – one PoE/PoH, 95W max; two standard network
connections suitable for interface to head end
network and ‘daisy chain’ type connection to second
camera or VJC-7000-90 location
Audio
Technical specifications
Electrical
Power
requirements
Input power 94.3 W
100 VAC - 240 VAC (90 VAC - 264 VAC with
tolerance considered), 50/60 Hz
Output power 82 W / 56V
- connector 3.5 mm stereo jack
- signal line in 9 kohm typical, 5.5 Vpp max
- signal line out 3.0 Vpp at 10 kohm typical,
2.3 Vpp at 32 okhm typical,
1.7 Vpp at 16 ohm typical
Loading...