How it Works
Bosch
Loading...
VEZ-523-EWTR
User Manual
74 pgs1.46 Mb0
Specsheet
4 pgs255.25 Kb0
Table of contents
Loading...

Bosch VEZ-523-EWCR, VEZ-523-IWTR, VEZ-523-IWCR, VEZ-523-EWTR User Manual

AUTODOME 5000 Analog PTZ Camera
VEZ-5000
en Operations Manual
AUTODOME 5000 Analog PTZ Camera Table of Contents | en 3

Table of contents

1
1.4 Important Safety Instructions 5
1.5 Important Notices 7
1.6 FCC and ICES Compliance (Class A) 9
2
3
4
5
5.1 Switches/Connectors 15
5.2 Communication Switch Setting 16
5.3 ID Setting 16
5.4 Camera Control Protocol Setting 17
5.5 Power Connector 18
5.6 Alarm I/O 18
5.7 RS-485 Connector Definition 19
5.8 Prepare the Camera for Assembly 20
5.9 Assemble the Indoor Camera 20
5.10 Assemble the Outdoor Camera 21
5.11 Accessories 22
6
6.1 Camera Setup Menu 24
6.2 Lens Setup Menu 26
6.3 PTZ Setup Menu 27
6.4 Display Setup Menu 29
6.5 Alarm Setup Menu 30
6.6 Language Setup Menu 31
6.7 Installer Menu 32
6.8 Monitor Display 33
6.9 Main Menu 35
6.9.1 Common Menus 36
6.10 Camera Setup 37
6.10.1 White Balance 37
6.10.2 Video Level 38
6.10.3 AutoSensUp Max 38
6.10.4 Exposure Mode 38
6.10.5 Backlight 39
6.10.6 Sharpness 39
6.10.7 WDR Function 39
6.10.8 Night Mode 39
6.10.9 Enhancement 39
6.10.10 DNR 39
6.11 Lens Setup 40
6.11.1 Auto Focus 40
Safety 5
Description 11
Unpacking 12
Installation 14
Connection 15
On-Screen Display (OSD) Menu 24
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
4 en | Table of Contents AUTODOME 5000 Analog PTZ Camera
6.12.1 Autopan 41
6.12.2 Tour 42
6.12.3 Preset Tour 43
6.12.4 Preset 44
6.12.5 Freeze 46
6.13.5 Motion Track 52
6.14 Alarm Setup 52
6.14.1 Alarm Setting 52
6.14.2 Alarm Detect 55
6.15 Language 57
6.16 Installer Setup 57
6.16.1 System Setup 57
6.16.2 Camera Setting 60
7
8
9
10
Operation 62
Troubleshooting 66
Technical data 68
Appendices 69
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
!
!
!
AUTODOME 5000 Analog PTZ Camera Safety | en 5
1
1.1
1.2

Safety

About this Manual

This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing. Because of the ongoing development of products, the content of the manual may change without notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness, or discrepancies between the manual and the product described.

Conventions in this Manual

In this manual, the following symbols and notations are used to draw attention to special situations:
Danger!
This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death.
Warning!
Indicates a potentially hazardous situation. If not avoided, this could result in serious bodily injury or death.
1.3
Caution!
Medium Risk Indicates a potentially hazardous situation. If not avoided, this may result in minor or moderate injury. Alerts the user to important instructions accompanying the unit.
Caution!
Indicates a potentially hazardous situation. If not avoided, this may result in property damage or risk of damage to the unit.
Notice!
This symbol indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property.

Legal Information

Copyright
This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
1.4
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |

Important Safety Instructions

Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit.
en | Safety AUTODOME 5000 Analog PTZ Camera
6
1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol cleaners.
2. Heat Sources - Do not install the unit near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.
3. Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent overheating and ensure reliable operation. Do not block or cover these openings. Do not place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's instructions have been adhered to.
4. Object and liquid entry - Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled with liquids, such as vases or cups, on the unit.
5. Lightning - For added protection during a lightning storm, or when leaving this unit unattended and unused for long periods, unplug the unit from the wall outlet and disconnect the cable system. This will prevent damage to the unit from lightning and power line surges.
6. Controls adjustment - Adjust only those controls specified in the operating instructions. Improper adjustment of other controls may cause damage to the unit. Use of controls or adjustments, or performance of procedures other than those specified, may result in hazardous radiation exposure.
7. Overloading - Do not overload outlets and extension cords. This can cause fire or electrical shock.
8. Power cord and plug protection - Protect the plug and power cord from foot traffic, being pinched by items placed upon or against them at electrical outlets, and its exit from the unit. For units intended to operate with 230 VAC, 50 Hz, the input and output power cord must comply with the latest versions of IEC Publication 227 or IEC Publication 245.
9. Power disconnect - Units have power supplied to the unit whenever the power cord is inserted into the power source, or when High Power-over-Ethernet (High PoE) power is provided over the Ethernet CAT 5E/6 cable. The unit is operational only when the ON/OFF switch is in the ON position. The power cord is the main power disconnect device for switching off the voltage for all units. When High PoE or PoE+ (820.3at) is used to power the unit, the power is provided over the Ethernet cable, which is then the main power disconnect device for switching off the voltage for all units.
10. Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit. For battery powered units, refer to the operating instructions. For external power supplied units, use only the recommended or approved power supplies. For limited power source units, this power source must comply with EN60950. Substitutions may damage the unit or cause fire or shock. For 24 VAC units, voltage applied to the unit's power input should not exceed ±10%, or 28 VAC. User-supplied wiring must comply with local electrical codes (Class 2 power levels). Do not ground the supply at the terminals or at the unit's power supply terminals. If unsure of the type of power supply to use, contact your dealer or local power company.
11. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Safety | en 7
12. Damage requiring service - Unplug the unit from the main AC power source and refer servicing to qualified service personnel when any damage to the equipment has occurred, such as: the power supply cord or plug is damaged; exposure to moisture, water, and/or inclement weather (rain, snow, etc.); liquid has been spilled in or on the equipment; an object has fallen into the unit; unit has been dropped or the unit cabinet is damaged; unit exhibits a distinct change in performance; unit does not operate normally when the user correctly follows the operating instructions.
13. Replacement parts - Be sure the service technician uses replacement parts specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized substitutions may cause fire, electrical shock, or other hazards.
14. Safety check - Safety checks should be performed upon completion of service or repairs to the unit to ensure proper operating condition.
15. Installation - Install in accordance with the manufacturer's instructions and in accordance with applicable local codes.
16. Attachments, changes or modifications - Only use attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the warranty or, in the case of an authorization agreement, authority to operate the equipment.
1.5

Important Notices

Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury and/or serious damage to the unit. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over. Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to overturn. Mount the unit per the manufacturer's instructions. All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at least 3 mm in each pole, into the electrical installation of the building. If you must open the housing for servicing and/or other activities, use this all-pole switch as the main disconnect device for switching off the voltage to the unit. Camera grounding - For mounting the camera in potentially damp environments, ensure to ground the system using the ground connection of the power supply connector. Camera lens - An assembled camera lens in the outdoor housing must comply and be tested in accordance with UL/IEC60950. Any output or signal lines from the camera must be SELV or Limited Power Source. For safety reasons, the environmental specification of the camera lens assembly must be within the environmental specification. Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60).
Coax grounding:
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
8 en | Safety AUTODOME 5000 Analog PTZ Camera
– Ground the cable system if connecting an outside cable system to the unit. – Connect outdoor equipment to the unit's inputs only after this unit has had its grounding
plug connected to a grounded outlet or its ground terminal is properly connected to a ground source.
– Disconnect the unit's input connectors from outdoor equipment before disconnecting the
grounding plug or grounding terminal.
– Follow proper safety precautions such as grounding for any outdoor device connected to
this unit. U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides information regarding proper grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Notice!
This device is intended for use in public areas only. U.S. federal law strictly prohibits surreptitious recording of oral communications.
Cold Start-ups - If camera is powered up in extremely cold temperature (for example, -40°C), please allow 30 minutes warm-up after powering camera prior to operation. In some cases, camera may require a soft reset or a power cycle before usable video is available. Environmental statement - Bosch has a strong commitment towards the environment. This unit has been designed to respect the environment as much as possible. Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid electrostatic discharge. NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostatic-sensitive printed circuit boards. Fuse rating - For security protection of the device, the branch circuit protection must be secured with a maximum fuse rating in accordance with NEC800 (CEC Section 60). Grounding and polarization - This unit may be equipped with a polarized alternating current line plug (a plug with one blade wider than the other blade). This safety feature allows the plug to fit into the power outlet in only one way. If unable to insert the plug fully into the outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for earth grounding). This safety feature allows the plug to fit into a grounded power outlet only. If unable to insert the plug into the outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the grounding plug. Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive force or shock may damage the unit. Outdoor signals - The installation for outdoor signals, especially regarding clearance from power and lightning conductors and transient protection, must be in accordance with NEC725 and NEC800 (CEC Rule 16-224 and CEC Section 60). Permanently connected equipment - Incorporate a readily-accessible disconnect device in the building installation wiring. Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights. Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Safety | en 9
1.6

FCC and ICES Compliance (Class A)

FCC ET ICES INFORMATION (commercial applications)
(U.S.A. and Canadian Models Only, CLASS A)
Notice!
This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: – this device may not cause harmful interference, and – this device must accept any interference received, including interference that may cause
undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his expense. Intentional or unintentional modifications, not expressly approved by the party responsible for compliance, shall not be made. Any such modifications could void the user's authority to operate the equipment. If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
INFORMATIONS FCC ET ICES (applications commerciales )
(modèles utilisés aux États-Unis et au Canada uniquement, CLASSE A)
Notice!
Ce produit est un appareil de Classe A. Son utilisation dans une zone résidentielle risque de provoquer des interférences. Le cas échéant, l’utilisateur devra prendre les mesures nécessaires pour y remédier.
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux conditions suivantes: – cet appareil ne peut pas provoquer d'interférence nuisible et – cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y
compris les interférences qui pourraient influer sur son bon fonctionnement. Suite à différents tests, cet appareil s’est révélé conforme aux exigences imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont destinées à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est utilisé dans une installation commerciale. Cette appareil génère, utilise et émet de l'energie de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme aux instructions, générer des
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
10 en | Safety AUTODOME 5000 Analog PTZ Camera
interférences nuisibles aux communications radio. L’utilisation de ce produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas échéant, l’utilisateur devra remédier à ces interférences à ses propres frais. Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision, qui procédera à une opération corrective. La brochure suivante, publiée par la Commission fédérale des communications (FCC), peut s’avérer utile : « How to Identify and Resolve Radio­TV Interference Problems » (Comment identifier et résoudre les problèmes d’interférences de radio et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Description | en 11
2

Description

The AUTODOME 5000 Analog PTZ Dome Camera delivers up to 432x zoom ratio to capture clear image in the distance. Continuous Auto Focus, Back Light, Auto Exposure and Auto SensUp Max functions are provided for clear and high quality image. Night Mode ensures 24 hours operation, while Privacy Masking is specially designed to avoid any intrusive monitoring at specific region; all of the salient functions can be incorporated to meet your needs. The Home function allows users to specify a preset position as the “home position” or choose a preferred action as the “Home function” (Preset Tour / Auto Pan / Tour). If the Home function is enabled, the camera can return to the preset home position or function when the camera has been idled for a user-defined period of time. Additionally, the unique Schedule function enables users to program a preset point or function (Preset Tour / Auto Pan / Tour) for the selected actions to be automatically initiated at specified times. The camera provides variable pan/tilt speeds ranging from a fast patrol of 360° per second to a slow ramble of 5° per second with 0.225° pan/tilt accuracy for fast and accurate tracking ability. The 360° endless rotation and 0° to 90° tilt travel help to track the object passing directly beneath the camera. Maximum 99 preset points can be programmed for precise location of target areas, and users can also define Preset Tour, Auto Pan and Tour lines for the camera to operate automatically. In addition, a RS-485 communication port is available for remote control. The camera provides 4 alarm inputs and 2 alarm relay outputs, and the smart alarm management mechanism can be programmed through the OSD setup menu. A chosen action (Preset / Preset Tour / Auto Pan / Tour) can be activated when an alarm is triggered. The built-in protocols include OSRD and Pelco P/D, which allow the camera to be integrated with surveillance systems of other suppliers.
Features
– 432X Zoom ( 36X Zoom, 12X Digital) – 960H Double Scan CCD sensor – 720TVL Sensor resolution – Wide Dynamic Range ( WDR) – True Day & Night ( IR Cut Filter) – Digital Noise Reduction – 360° Endless Pan Range – 0° to 90° Tilt Angle – Manual speed 0.5° to 90° /s – 99 Preset Positions / 5° to 360° per second Pre-position Speed – 8 Tour – 4 Autopan – 8 Preset Tour – Up to 20 Privacy Masking zone – Image Enhancement / AGC Control – 4 Alarm Inputs, 2 Alarm Outputs ( N.C. / N.O./ OFF) – Multi-language On-Screen Display – Bosch OSRD, Pelco P/D Protocol – Compatible external devices ( LTC-5136,MIC-BP3, UPA-2450-50 / UPA-2450-60) – Programmable PTZ Speed: Proportional to Zoom ratio, changeable preset speed
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
12 en | Unpacking AUTODOME 5000 Analog PTZ Camera
3
3.1

Unpacking

Parts List

Quanity Graphic Description
1 Mounting Adapter
1 Dome Camera Body without
Sunshield
1
1 Dome Camera Body with Sunshield
1 M5x8L security screw for mounting
adapter
1 T20 Security Torx wrench for M5x8L
security screw
1
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Unpacking | en 13
Quanity Graphic Description
1 T10 Security Torx wrench for dome
bubble
1 Lubricant
1 User Manual
Notice!
1. Your package contains one Dome Camera Body, depending if you purchased an indoor (without sunshield) or an outdoor (with sunshield) camera.
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
14 en | Installation AUTODOME 5000 Analog PTZ Camera
4

Installation

Follow the instructions below to complete cable connections of the AUTODOME 5000 camera. Connect the camera to other devices as shown in the diagram to complete a video surveillance solution.
Figure 4.1: System Configuration
1
Repeater
2 AUTODOME 5000 camera
3 Video cable
4 Switch/Quad/Mux/DVR
5 Main monitor
6 Call monitor
7 Control keyboard
Notice!
To extend the network distance up to 1.2 km (4000 feet) and to protect the connected devices, it is highly recommended to place a repeater at the mid-point. However, a repeater may be needed in the network distance less than 1.2 km if the used cables are not the CAT 5, 24-gauge cables. Refer to section RS-485. For detailed information about the repeater, refer to its manual.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Connection | en 15
5
5.1

Connection

Switches/Connectors

Configuring the camera’s ID and communication protocol is required before connecting the camera to other devices. The switches used for configuring these settings are located on the camera’s back plate. Refer to the diagram and table below for positions and definition of the switches / connectors.
Letter Description
A Alarm I/O
B Camera ID setup dip switch
C BNC video output
D Communication switch
E Camera control protocol switcher
F RS-485 connector
G Power connector
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
16 en | Connection AUTODOME 5000 Analog PTZ Camera
5.2

Communication Switch Setting

Communication Switch
The camera’s communication switches are specified in the table below.
Communication Switch Switches Description
SW1
SW2
SW3
SW4
SW5 Reserved
SW6 Reserved
RS-485 Setting
The camera uses an RS-485 interface to communicate with the control device. For this reason, the RS-485 setup of the camera and the control device must be the same. The default RS-485 setting is half-duplex. Do not change the default setting without any support from qualified specialists or suppliers.
RS-485 Setting
5.3
RS-485 Setting
Half-Duplex Full-Duplex

ID Setting

If there is more than one camera in the same network, you must assign an ID number to each camera. Access the OSD menu and go to <INSTALLER MENU> → <CAMERA ID SETTING> → <ID SETTING> to assign the camera’s ID number. Refer to the section Camera Setting for detail setting instructions.
Notice!
No two cameras in the same network should be given the same ID, or communication conflict may occur.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
ON
1 2 3 4 5 6 7 8 9 10
AUTODOME 5000 Analog PTZ Camera Connection | en 17
For users who wish to set up the camera ID via the dip switch at the camera’s back plate, first choose <HW> as the setting type under the <ID SETTING> menu. Then the camera’s ID can be setup using the 10-bit ID dip switch. If the camera’s ID number is 6, for instance, the ID switch SW 2 and SW 3 should be set to “ON” and the rest should be set to “OFF” as shown below.
For switch configuration details, refer to Appendices, page 69.
Notice!
If you need to setup the camera ID via the dip switch at the camera’s back plate, the setting type MUST be changed to <HW>. Otherwise the dip switch WILL NOT be enabled.
5.4

Camera Control Protocol Setting

Define the camera control protocol according to the devices of the surveillance system. Generally, use one protocol even the devices are provided from different manufacturers. Refer to the table below for all supported protocols with their matching switch numbers and baud rate. Choose an appropriate protocol for the camera.
Switch Number
00 Pelco D 2400
01 Pelco D 4800
02 Pelco D 9600
04 Pelco P 1200
05 Pelco P 4800
06 Pelco D 9600
10 Bosch OSRD 9600
Protocol Baud Rate
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
ON
1 2 3 4 5 6
123456
18 en | Connection AUTODOME 5000 Analog PTZ Camera
Use the 6-bit dip switch (Camera Control Protocol Switch) to set the camera’s control protocol and its baud rate. If protocol “Pelco D” is selected, which is switch no. 01 and baud rate 4800, for instance, set the SW-1 to “ON” and the rest to “OFF” as shown below.
For more switch configurations, refer to Appendices, page 69.
5.5
5.6

Power Connector

Before connecting the power wires, refer to the illustrations below for definition of the power connector. Be sure to connect to the correct position.
Power Connector
Switch Number
SW1 AC 24V_1 (24 VAC)
SW2 GND (Ground)
SW3 AC24V_2 (24 VAC)
Description

Alarm I/O

The camera supports 4 digital alarm inputs and 2 digital alarm outputs. Make sure the alarm connections are properly wired before starting to configure alarm related settings. Refer to the pin definition table below for alarm system wiring.
1 ALARM_OUT_NO_1 7 ALARM_OUT_COM_2
2 ALARM_OUT_NC_1 8 GND
3 ALARM_OUT_COM_1 9 ALARM_IN_4
4 GND 10 ALARM_IN_3
5 ALARM_OUT_NO_2 11 ALARM_IN_2
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
6 ALARM_OUT_CN_2 12 ALARM_IN_1
AUTODOME 5000 Analog PTZ Camera Connection | en 19
5.7

RS-485 Connector Definition

Before connecting the RS-485 wires, refer to the illustrations below for definition of the RS-485 connector.
RS-485 Connector Switch
Number
SW1 R-
SW2 GND
SW3 R+
SW4 T-
SW5 T+
Descriptio n
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
1
2
3
4
5
20 en | Connection AUTODOME 5000 Analog PTZ Camera
5.8
5.9

Prepare the Camera for Assembly

The camera is shipped with a PE cloth sheet covering the inside the dome cover and a lens cap attached to the lens. Follow the steps below to remove them.
1. Loosen the screws from the top of the Dome Cover.
2. Rotate and detach the Dome Cover from the Dome Camera Body.
3. Remove the PE cloth sheet and take off the lens cap.

Assemble the Indoor Camera

Refer to the following illustration and descriptions for the assembly of the Indoor Dome Camera.
1 M5x8L Mechanical Screw with Spring
washer (1 piece)
2 Indoor Adaptor 5 M3x23L Screw with Rubber (2 pieces)
3 Dome Camera Body
Assembly Instructions
1. Attach the Bubble (4) to the Dome Camera Body (3) and fasten the M3x23L screws (5).
2. Attach the Indoor Adaptor (2) to the Camera Body (3) by turning clockwise and fasten the M5x8L screw (1) after all cables are connected to the camera back plate.
Notice!
If the Dome Camera will be attached to a wall or a pipe mount, ensure that the Indoor Adaptor is attached to the wall or pipe mount prior to attaching the Camera Dome Body.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
4 Bubble
1
2
3
4
5
6
7
AUTODOME 5000 Analog PTZ Camera Connection | en 21
5.10

Assemble the Outdoor Camera

Refer to the following illustration and descriptions for the assembly of the Outdoor Dome Camera.
1 M5x8L Mechanical Screw with Spring
Washer (1 piece)
2 Outdoor Adaptor 5 Camera Body
3 M4x21L Mechanical Screw with Spring
Washer (3 pieces)
7 M3x23L Screws with Rubber (2
pieces)
4 Sunshield
6 Bubble
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
!
22 en | Connection AUTODOME 5000 Analog PTZ Camera
Assembly Instructions
1. Attach the Bubble (6) to the Camera Body (5) and fasten the two M3x23L screws (7).
2. Attach the Sunshield (4) to the Camera Body (5) by fastening the three (3) M4x21L screws.
3. Attach the Outdoor Adaptor (2) to the Camera Body (5) by turning clockwise and fasten the M5x8L screw (1) after all cables are connected to the camera back plate.
Notice!
If the Dome Camera will be attached to a wall or pipe mount, ensure that the Outdoor Adaptor is attached to the wall or pipe mount prior to attaching the Camera Dome Body.
5.11

Accessories

The AUTODOME 5000 Series PTZ Dome camera comes with the hardware and installation instructions necessary to mount the camera to a ceiling. These following mounting accessories are available (and are supplied with separate mounting instructions):
Model Number Description Application
VEZ-A5-WL Wall Mount Indoor/outdoor vertical walls
VEZ-A5-PP Pipe Mount Indoor/outdoor high ceilings
VEZ-A5-IC In-ceiling (Recessed)
Mount
VDA-CMT-PTZDOME Corner mount adapter Indoor/outdoor corner (used
VDA-POMT-PTZDOME Pole mount adapter Indoor/outdoor mast (used
Caution!
Installation The installation should be made by qualified installation personnel and conform to the National Electrical Code and applicable local codes.
Indoor drop-ceiling
with the VEZ-A5-WL Wall Mount)
with the VEZ-A5-WL Wall Mount)
Danger!
Servicing TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS, UNLESS YOU ARE QUALIFIED TO DO SO. In USA and Canada, use Class 2 power supply unit (PSU) only.
2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Connection | en 23
Notice!
Use of Grounded Conduit A grounded conduit is required in order to meet the EMC Regulation Requirements.
Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |
Loading...
+ 51 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use