Bosch VDx-244 User Manual

VDx-244 - Quick Install

1 2 3 4

139 (5.47)

1/2

Mounting anchors

Guide pattern

Rubber pad

Dome base

4 mounting screws

Inner dome

Dome cover

Key

13.3 (0.52)

34.5 (1.35)

54.2 (2.13)

13.8 (0.54)

51.7 (2.03)

100.2 (3.94)

PT 1/2" TAPPT 1/2" TAP

4– Ø4.4±0.1

13.8 (0.54)

51.7 (2.03)13.8 (0.54)

102.0 (4.01)

51.7 (2.03)

13.8 (0.54)

mm (in)

24 VAC / 12 VDC Class 2

BNC female

1 Vpp 75 Ohm

not included

Menu (set)

LEFT

INT

RIGHT

Focus

Zoom

Twist

Tilt

Pan

1Safety

1.1 Safety precautions

DANGER!

High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation. If not avoided, this could result in property damage or risk of damage to the unit.

CAUTION!

The Low Voltage power supply unit must comply with EN60950 / UL60065. The power supply must be a SELV-LPS unit or a SELV - Class 2 unit (Safety Extra Low Voltage - Limited Power Source).

CAUTION!

Installation should only be performed by qualiﬁed service personnel in accordance with the National Electrical Code or applicable local codes.

1.2 Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions

5. Clean only with a dry cloth.

6. Install in accordance with the manufacturer's instructions.

7. Do not install unit near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

8. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

9. Only use attachments/accessories speciﬁed by the manufacturer.

10. Unplug this apparatus during lightning storms or when unused for long periods of time.

11. Refer all servicing to service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

1.3 FCC & ICES compliance

FCC & ICES Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – reorient or relocate the receiving antenna; – increase the separation between the equipment and

receiver;

– connect the equipment into an outlet on a circuit different

from that to which the receiver is connected;

– consult the dealer or an experienced radio/TV technician

for help.

Intentional or unintentional modiﬁcations, not expressly approved by the party responsible for compliance, shall not be made. Any such modiﬁcations could void the user's authority to operate the equipment. If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action.

1.4 Bosch notices

Disposal - Your Bosch product was developed and

manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products. Please dispose of these units at an environmentally compatible recycling facility, per European

Directive 2002/96/EC

Optical elements

Optical elements are sensitive and should be protected at all times. Do not allow objects to come into contact with glass surfaces and do not touch optical elements with your ﬁngers.

Trademarks

All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

Note

Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between the user guide and the product described.

More information

For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com

AM18-Q0642

WDR Analog Camera Menus Setup menu | en 1

Set

LEFT RIGHT

TOP

RIGHT

BOTTOM

reduce extend

ABCDEFGHIJKLMNOPQRSTU V

DEL EXIT

1Setup menu

Press straight down on the button of the control pad to access the SETUP menu.

– Move the button up or down to move the cursor through the menus.

– Move the button to the right or left to change values.

– When the symbol is shown, press straight down on the button to

select an item or open a submenu.

Navigation items at the bottom of the screen

– To move to the continuation of a menu, select NEXT. – To return to the previous menu, select BACK or RETURN. – To save changes, select SAVE ALL. – To close the SETUP menu, select EXIT.

1.1 Main menu

LENS

WHITE BAL

WDR

DNR

DAY/NIGHT

IMAGE ADJUST

GENERAL

WDR Analog Camera Menus Setup menu | en 2

1.1.1 Lens menu

LENS DC BRIGHTNESS 0~255

AGC 0~20

FLICKERLESS ON, OFF

DSS OFF, X2, X4, X6, X32, X64,

128X, X256, X512,

SHUTTER 1/60, 1/120, 1/250, 1/500,

1/1000, 1/2000, 1/4000,1/ 10000 (NTSC) 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 (PAL)

RETURN

ESC BRIGHTNESS 0~255

AGC 0~20

FLICKERLESS ON, OFF

DSS OFF, X2, X4, X6, X32, X64,

128X, X256, X512,

RETURN

– DSS (Digital Slow Shutter) increases the amount of light captured by

the factor selected. Use only in scenes with little movement.

WDR Analog Camera Menus Setup menu | en 3

1.1.2 White balance menu

WHTE BAL ATW ENVIRONMENT INDOOR, OUTDOOR

RETURN

PUSH

USER1, USER2

ANTI CR ENVIRONMENT INDOOR, OUTDOOR

MANUAL B-GAIN UP

PUSH LOCK

– ATW (Auto Tracking White balance: 2,500 K to 8,500 K) and PUSH (Full

pull-in: 1,800 K to 10,500 K) continuously analyze color temperature.

– Use ANTI CR (Anti Color Rolling) when certain types of fluorescent light

cause the picture to periodically change color.

– Use PUSH LOCK with a reference white object filling the screen.

R-GAIN 0~255

B-GAIN 0~255

RETURN

B-GAIN DOWN

PRESET

RETURN

WDR Analog Camera Menus Setup menu | en 4

1.1.3 Wide dynamic range menu

WDR WDR MODE WDR, DWDR

BRIGHTNESS 0~255

CONTRAST LOW, MID-LOW, MID, MID-

HIGH, HIGH

RETURN

BLC AREA AUTO, MANUAL

RETURN

HLC CLIP LEVEL 0~255

SCALE 0~15

RETURN

– WDR (Wide Dynamic Range) is a dual shutter exposure correction

function for high contrast scenes to obtain images with fewer blownout highlights and hidden shadows.

– Use BLC (Back Light Compensation) to see a dark object in front of a

bright background.

– Use HLC (High Light Compensation) to darken highlights and avoid

image wash-out (for example, car headlights).

WDR Analog Camera Menus Setup menu | en 5

1.1.4 Digital noise reduction menu

DNR 2DNR LEVEL LOW, MID, HIGH

RETURN

3DNR LEVEL AUTO, LOW, MID, HIGH

RETURN

OFF

– DNR (Digital Noise Reduction): In low ambient lighting conditions use

2DNR to reduce noise in still images; use 3DNR to reduce noise in scenes with movement.

1.1.5 Day/night menu

DAY/NIGHT AUTO DELAY CNT 0~15 SEC

D/N LEVEL LOW, MID, HIGH

RETURN

COLOR

B/W BURST ON, OFF

RETURN

WDR Analog Camera Menus Setup menu | en 6

1.1.6 Image adjust menu

IMAGE ADJUST

– DIS (Digital Image Stabilizer) electronically suppresses camera shake.

IMAGE SHARPNESS 0~15

GAMMA 0.38, 0.42, 0.45, 0.50,

0.55, 0.63, 0.71, 0.83

HR MODE OFF, X1, X2, X3, X4, X5, X6,

CONTRAST 0~63

RETURN

D-EFFECT DIS ON, OFF

D-ZOOM OFF, X2, X3, X4, X6, X8,

X16

MIRROR V-FFLIP, H-FLIP, HV-FLIP

FREEZE ON/OFF

NEGA/POSI NEGA/POSI

RETURN

COLORGAIN

R-GAIN 0~63

B-GAIN 0~63

RETURN

WDR Analog Camera Menus Setup menu | en 7

Image adjust menu - continued

MOTION AREA 1/4, 2/4, 3/4, 4/4

DISPLAY ON, OFF

DETECT AREA

WDR Analog Camera Menus Setup menu | en 8

1.1.7 General menu

GENERAL CAM TITLE OFF

WXYZ ( ) –. /0123456789

SENSITIVY 0~15

TOP 0~15

BOTTOM 1~16

LEFT 0~23

RIGHT 1~24

RETURN

PRIVACY AREA 1/15~15/15

DISPLAY ON, OFF

POSITION

COLOR GREEN, BLUE, YELLOW,

TRANSP 0.00, 0.50, 0.75, 1.00

MOSAIC ON, OFF

RETURN

Area selection for motion or privacy masks

Select area 1, 2, 3 or 4.

CYAN, MAGENTA, WHITE, BLACK, RED

LANGUAGE ENGLISH, JAPANESE, GERMAN, FRENCH,

SYNC INT

VERSION

FACTORY RESET

RETURN

When the camera title is ON, a virtual keyboard appears on the screen. Use the control pad to move to the character you want and select it. Repeat this to enter the camera ID you desire. You can enter up to 52 characters.

RETURN

RUSSIAN, PORTUGUESE, SPANISH, SIMPLIFIED CHINESE

L/L

SHIFT UP

SHIFT DOWN

PRESET

RETURN

– Top: extend or reduce upper limit of detection area.

– Bottom: extend or reduce bottom limit of detection area.

– Left: extend or reduce left limit of detection area.

– Right: extend or reduce right limit of detection area.