Register your new Bosch now:
www.bosch-home.com/welcome
Dishwasher
SM...
SB...
aus Instruction manual
5HVHWVHF
K
%
K PLQ
$
&
K
6WDUW
5HVHWVHF
Table of contents
ausI nstr ucti on manual
8 Intended use . . . . . . . . . . . . . . . . 4
( Safety instructions. . . . . . . . . . . . 4
Before you switch ON the
appliance . . . . . . . . . . . . . . . . . . . . . 5
Delivery. . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . 5
In daily use . . . . . . . . . . . . . . . . . . . . . 6
Door lock . . . . . . . . . . . . . . . . . . . . . . 6
Button lock . . . . . . . . . . . . . . . . . . . . . 8
Damage . . . . . . . . . . . . . . . . . . . . . . . 8
Disposal . . . . . . . . . . . . . . . . . . . . . . . 8
7 Environmental protection . . . . . 10
Packaging. . . . . . . . . . . . . . . . . . . . . 10
Old appliances . . . . . . . . . . . . . . . . . 10
* Getting to know your
appliance . . . . . . . . . . . . . . . . . . 11
Control panel . . . . . . . . . . . . . . . . . . 11
Appliance interior . . . . . . . . . . . . . . . 11
Overview of menu. . . . . . . . . . . . . . . 12
aus
- Utensils. . . . . . . . . . . . . . . . . . . . 14
Not suitable . . . . . . . . . . . . . . . . . . . . 14
Glass and utensil damage. . . . . . . . . 14
Loading the dishwasher . . . . . . . . . . 15
Upper basket. . . . . . . . . . . . . . . . . . . 15
Lower basket. . . . . . . . . . . . . . . . . . . 15
Cutlery basket . . . . . . . . . . . . . . . . . . 16
Cutlery drawer . . . . . . . . . . . . . . . . . . 16
Etagere . . . . . . . . . . . . . . . . . . . . . . . 17
Folding spikes . . . . . . . . . . . . . . . . . . 17
Small items holder. . . . . . . . . . . . . . . 17
Knife rack . . . . . . . . . . . . . . . . . . . . . 18
Baking sheet spray head. . . . . . . . . . 18
Unloading the dishwasher . . . . . . . . . 19
Adjusting the height of the basket. . . 19
. Detergent . . . . . . . . . . . . . . . . . . 20
Adding detergent. . . . . . . . . . . . . . . . 21
/ Overview of programmes . . . . . 22
Programme selection . . . . . . . . . . . . 23
Information for test institutes . . . . . . . 23
, Rinse aid . . . . . . . . . . . . . . . . . . . 13
Setting amount of rinse aid. . . . . . . . 13
Detergent with a rinse aid
component . . . . . . . . . . . . . . . . . . . . 14
Switching off rinse aid refill
indicator . . . . . . . . . . . . . . . . . . . . . . 14
0 Additional functions . . . . . . . . . 24
Speed Perfect . . . . . . . . . . . . . . . . . . 24
Half load . . . . . . . . . . . . . . . . . . . . . . 24
hygienePlus (HygienePlus) . . . . . . . . 24
intensiveZone . . . . . . . . . . . . . . . . . . 24
Extra Dry . . . . . . . . . . . . . . . . . . . . . . 24
1 Operating the appliance . . . . . . 25
AquaSensor. . . . . . . . . . . . . . . . . . . . 25
Switching on the appliance . . . . . . . . 25
Remaining running time display . . . . 25
Time preselection . . . . . . . . . . . . . . . 25
Programme end . . . . . . . . . . . . . . . . 26
Auto Power Off . . . . . . . . . . . . . . . . . 26
Switching off the appliance . . . . . . . . 26
Interrupting the programme. . . . . . . . 26
Terminating the programme . . . . . . . 27
Changing the programme . . . . . . . . . 27
ExtraDry. . . . . . . . . . . . . . . . . . . . . . . 27
3
aus Intended use
2 Cleaning and maintenance . . . 27
Overall status of the dishwasher . . . . 27
Machine Care . . . . . . . . . . . . . . . . . .28
Rinse aid . . . . . . . . . . . . . . . . . . . . . .29
Filters. . . . . . . . . . . . . . . . . . . . . . . . .29
Spray arms . . . . . . . . . . . . . . . . . . . .30
3 Fault, what to do?. . . . . . . . . . . 30
Waste water pump. . . . . . . . . . . . . . . 31
Fault table . . . . . . . . . . . . . . . . . . . . . 32
4 Customer service . . . . . . . . . . . 40
5 Installation and connection . . . 40
Contents of package . . . . . . . . . . . . . 40
Safety instructions . . . . . . . . . . . . . . .40
Delivery . . . . . . . . . . . . . . . . . . . . . . . 41
Technical specifications. . . . . . . . . . . 41
Installation . . . . . . . . . . . . . . . . . . . . .41
Drainage connection . . . . . . . . . . . . .41
Drinking water connection . . . . . . . . .42
Hot water connection. . . . . . . . . . . . .42
Electrical connection . . . . . . . . . . . . .43
Removal . . . . . . . . . . . . . . . . . . . . . . 43
Transporting. . . . . . . . . . . . . . . . . . . .43
Protection against frost
(Emptying the appliance). . . . . . . . . .43
8 Intended use
I nt ended use
■ This appliance is intended
for use in the home and
domestic environments.
■ Use the dishwasher only in
the home and only for its
designated purpose: for
washing domestic dishes.
■ This appliance is intended
for use up to a maximum
altitude of 4000 metres
above sea level.
( Safety instructions
Saf e t y instructions
This appliance may be used by
children over the age of 8 years
old and by persons with
reduced physical, sensory or
mental capabilities or by
persons with a lack of
experience or knowledge if they
are supervised or are instructed
by a person responsible for
their safety how to use the
appliance safely and have
understood the associated
hazards.
Children must not play with, on,
or around the appliance.
Children must not clean the
appliance or carry out general
maintenance unless they are at
least 8 years old and are being
supervised.
4
Safety instructions aus
Keep children below the age of
8 years old at a safe distance
from the appliance and power
cable.
Before you switch ON the
appliance
Please read the instructions for
use and installation carefully.
They contain important
information on how to install,
use and maintain the appliance.
Retain all documents for later
use or for the subsequent
owner.
You can download the
instructions for use from our
website free of charge. The
relevant Internet address can
be found overleaf on these
instructions for use.
Delivery
1. Check the packaging and
dishwasher immediately for
damage caused in transit.
Do not switch on a damaged
appliance, but contact your
supplier.
2. Please dispose of the
packaging material in an
environmentally friendly
manner.
3. Do not let children play with
packaging and its parts.
There is a risk of suffocation
from collapsible boxes and
film.
Installation
■ Following installation, ensure
that the back of the
dishwasher is not freely
accessible (protection
against contact due to hot
surface).
■ Install and connect the
appliance according to the
installation and assembly
instructions.
■ Prior to installation,
disconnect the dishwasher
from the power supply.
■ Ensure that the protective
conductor system of the
domestic supply has been
correctly installed.
■ The electrical connection
conditions must correspond
with the specifications on the
dishwasher rating plate 9*.
■ If the power cord of this
appliance is damaged, it
must be replaced with a
particular power cord.
To prevent injury, the power
cord may be purchased from
customer service only.
■ If the dishwasher is installed
in a high-sided unit, the unit
must be secured properly.
■ If the dishwasher is installed
below or above other
domestic appliances, follow
the information for
installation in combination
with a dishwasher in the
installation instructions for
the particular appliances.
5
aus Safety instructions
■ Also follow the installation
instructions for the
dishwasher to ensure that all
appliances are operated
safely.
■ If there is no information or if
the installation instructions
do not include the
appropriate information,
contact the manufacturer of
these appliances to ensure
that the dishwasher can be
installed above or below
these appliances.
■ If you cannot obtain any
information from the
manufacturer, you must not
install the dishwasher above
or below these appliances.
■ If you install a microwave
oven above the dishwasher,
the microwave oven may be
damaged.
■ Install built-under or
integratable appliances only
under continuous worktops
which have been screwed to
adjacent cupboards to
ensure stability.
■ Do not install the appliance
near heat sources (radiators,
heat storage tanks, cookers
or other appliances which
generate heat) and do not
install under a hob.
■ Please note that the
insulation material of the
dishwasher power cord may
melt next to heat sources
(e.g. heating / hot water
installations) or hot
appliance parts. Make sure
that the power cord of the
dishwasher never comes into
contact with heat sources or
hot appliance parts.
■ After installing the appliance,
ensure that the plug is easily
accessible. ~ "Electrical
connection" on page 43
■ For some models:
The plastic housing on the
water connection contains an
electric valve. The supply
hose contains electrical
connection cables. Do not
cut through the supply hose.
Do not immerse the plastic
housing in water.
In daily use
Read and observe the safety
information and instructions for
use on the packaging for
cleaning and rinsing agents.
Childproof lock (door lock) *
Doo r lock
The child-proof lock (door lock)
protects children from potential
hazards which the dishwasher
poses.
6
Safety instructions aus
:Warning
Risk of suffocation!
Children may become locked in
the dishwasher and suffocate.
Always completely close the
appliance door when leaving
the dishwasher.
Activate the child-proof lock
(door lock) as follows:
1. Pull the catch of the
child-proof lock towards
yourself (1).
2. Close the door (2).
The child-proof lock is
activated.
Open the door with activated
child-proof lock (door lock) as
follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Open the door (2).
Deactivate the child-proof lock
(door lock) as follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Press the catch of the
child-proof lock backwards
(2).
The childproof lock is
deactivated.
* depending on the features of
your dishwasher
7
aus Safety instructions
Childproof lock (button lock)
Button lock
You can prevent your
dishwasher being switched off
inadvertently (e.g. by children
pressing the buttons).
Here’s how to activate the
button lock:
1. Start the desired
programme.
2. Press and hold the F button
for about 4 seconds.
In the display window you
will see ’–.
The button lock has now been
activated.
If any of the buttons are
pressed while the programme
is running, ’– will appear in the
display window. It is not
possible to cancel the
programme (Reset).
To deactivate the button lock,
hold down the F button for
about 4 seconds until ’–
disappears from the display
window.
The button lock is cancelled
automatically at the end of the
programme. In the event of a
power failure, the button lock
will be maintained. You need to
reactivate the button lock at the
beginning of every programme.
Damage
■ The appliance may be
repaired and opened up by a
technician only. To do this,
disconnect the appliance
from the power supply. Pull
out the mains plug or switch
off the fuse. Turn off the tap.
■ If the appliance is damaged,
especially the control panel
(cracks, holes, broken
buttons), or the door function
is impaired, stop operating
the appliance. Pull out the
mains plug or switch off the
fuse. Turn off tap, call
customer service.
Disposal
1. Make redundant appliances
unusable to prevent
subsequent accidents.
2. Dispose of the appliance in
an environmentally friendly
manner.
8
Safety instructions aus
:Warning
Risk of injury!
■ To prevent injuries, e.g.
caused by stumbling, open
the dishwasher only briefly in
order to load and unload the
dishwasher.
■ Knives and other utensils
with sharp points must be
placed with the points
downwards in the cutlery
basket*1R or horizontally
on the knife shelf* or in the
cutlery drawer*1".
■ Do not lean or sit on the
open door.
■ In the case of free-standing
appliances, ensure that the
baskets are not overloaded.
The appliance could tip.
■ If the appliance is not in a
cavity and a side panel is
accessible, the door hinge
area must be covered at the
side for reasons of safety
(risk of injury). The covers
are available as optional
accessories from customer
service or specialist outlets.
* depending on the features of
your dishwasher
:Warning
Risk of explosion!
Do not add any solvents to the
rinsing compartment. Danger of
explosion!
:Warning
Risk of scalding!
Open the door carefully when
the programme is still running.
There is a risk of hot water
spraying out of the appliance.
:Warning
Risk to children!
■ If fitted, use the childproof
lock.
■ Do not allow children to play
with or operate the
appliance.
■ Keep children away from
detergents and rinse aid.
These may cause chemical
burns in the mouth, throat
and eyes or asphyxiation.
■ Keep children away from
open dishwasher. There may
be small parts in the
dishwasher which children
could swallow and the water
inside the dishwasher is not
drinking water as it may
contain detergent residue.
9
aus Environmental protection
■ Ensure that children do not
place fingers in the tablet
collecting tray 1:. Small
fingers could become caught
in the slots.
■ When opening and closing
the door on an eye-level
appliance, ensure that
children do not become
jammed or crushed between
the appliance door and the
cupboard door below.
■ Children could become
locked in the appliance
(danger of suffocation) or get
into another dangerous
situation.
Redundant appliances: Pull
out the mains plug, sever
and dispose of the power
cord. Destroy the door lock
so that the door can no
longer be closed.
7 Environmental
protection
Envi r on mental pr ot ect i on
Both the packaging of new appliances
and the old appliances themselves
contain valuable raw materials and
recyclable materials.
Please dispose of the individual parts
separated according to type.
Please ask your dealer or inquire at
your local authority about current means
of disposal.
Packaging
All plastic parts of the appliance are
identified with internationally
standardised abbreviations (e.g. PS
polystyrene). Therefore, plastic waste
can be sorted out when the appliance is
being disposed of.
Please follow the safety instructions
under “Delivery” ~ Page 5.
Old appliances
Please follow the safety instructions
under “Disposal of your appliance”
~ Page 8.
This appliance has been
identified in accordance with the
European Directive 2012/19/EU
on Waste Electrical and
Electronic Equipment (WEEE).
The directive provides a
framework for the collection and
recycling of old appliances,
which is valid across the EU.
10
Getting to know your appliance aus
* Getting to know your
appliance
Gett i ng to know y our appl i ance
Diagrams of the control panel and the
interior of the appliance can be found at
the front of the manual. Individual
positions are referred to in the text.
Control panel
See Fig. ~ Page 2
( On/off switch
0 Programme buttons **
8 Door opener
@ Time preselection
H Additional functions/programme
buttons **
P START button
X Display "Check water supply"
` Rinse aid refill indicator
h Display window
* depending on the features of your
dishwasher
** number depending on the features of
your dishwasher
Appliance interior
See Fig. ~ Page 2
1" Cutlery drawer *
1* Top basket
12 Upper spray arm
1: Tablet collecting tray
1B Lower spray arm
1J Filters
1R Cutlery basket *
1Z Bottom basket
1b Dispenser for rinse aid
1j Detergent dispenser
9" Lock for detergent dispenser
9* Rating plate
* depending on the features of your
dishwasher
11
aus Getting to know your appliance
Overview of menu
The settings can be found in the
individual chapters. You can change
The dishwasher has been preset with
these factory settings.
certain settings for your convenience.
Setting up Factory setting Description
§ Rinse aid
§:‹† Amount of rinse aid affects drying. When
using Multitabs, select setting 0.
§:‹‹ - §:‹‡
š ExtraDry
š:‹‹ / Off Improved drying for glasses and plastic
tableware.
š:‹‹ - š:‹‚
‘ Hot water *
‘:‹‹ / Off The dishwasher can be connected to
either hot (40-60°C) or cold water
‘:‹‹ - ‘:‹‚
˜ Auto Power Off
˜:‹‚ Appliance automatically switches off at
(<40°C).
the end of each wash.
˜:‹‹ - ˜:‹ƒ
* depending on the configuration of your specific dishwasher
--------
12
Rinse aid aus
, Rinse aid
Ri ns e ai d
The rinse aid ensures stain-free dishes
and clear glasses. Use only rinse aid
for domestic dishwashers. As soon as
the rinse aid refill indicator ` lights up
in the control panel, there is still a rinse
aid reserve of 1-2 rinse cycles. Top up
the rinse aid.
Top up the rinse aid as follows:
1. Open dispenser 1b; press lug on
the lid (1) and lift (2).
2
1
2. Add rinse aid up to the max. mark.
Setting amount of rinse aid
You can set the amount of rinse aid that
should be added to a value between
§:‹‹ and §:‹‡. Setting the amount of
rinse aid to be dispensed to §:‹† will
give you a very good drying result. The
factory setting is §:‹†.Do not change
the amount of rinse aid unless there are
streaks or water stains on the utensils.
Set a lower level to avoid streaks. Set a
higher level to avoid water stains.
Here’s how to set the amount of rinse
aid:
1. Switch on ON/OFF switch (.
2. Hold down the programme button
# and then repeatedly press the
START button P until š:‹...
appears in the display window.
3. Release both buttons.
4. Press the programme button #
repeatedly until the factory setting
value §:‹† appears in the display
window h.
5. Press the programme button 3.
Each time the button is pressed, the
set value increases by one level;
when it reaches the value §:‹‡ the
display jumps back to §:‹‹ (Off).
6. Press START button P.
The set value is saved.
PD[
3. Close the lid.
The lid "clicks" into position.
4. Remove overflowed rinse aid with a
cloth.
This prevents excessive frothing
during the next rinse cycle.
13
aus Utensils
Using detergent with a rinse
aid component
Det er ge n t wi t h a rinse ai d component
In general, you can use detergent with
a rinse aid component up to a water
hardness level of 21 °dH (37 °fH, 26
°Clark, 3.7 mmol/L) without adding
rinse aid. Above a water hardness value
of 21 °dH, use additional rinse aid.
Switching off rinse aid refill
indicator
If the rinse aid refill indicator `
bothers you (e.g. if you are using a
combination detergent with a rinse aid
component), you can switch off the
rinse aid refill indicator.
Proceed as described under "Setting
rinse aid quantity" and set the level to
§:‹‹. The rinse aid refill indicator ` is
switched off.
- Utensils
Utensils
Not suitable
■ Cutlery and utensils made of wood.
■ Delicate decorative glasses, craft
and antique utensils. These decors
are not dishwasher-proof.
■ Plastic parts not resistant to heat.
■ Copper and tin utensils.
■ Utensils which are soiled with ash,
wax, lubricating grease or ink.
Aluminium and silver parts have
a tendency to discolour and fade during
the wash cycle. Even some types of
glass (e.g. crystal glass objects) may
turn cloudy after many wash cycles.
Glass and utensil damage
Causes:
■ Glass type and glass production
process.
■ Chemical composition of the
detergent.
■ Water temperature of the wash
programme.
Recommendation:
■ Use only glasses and porcelain
which the manufacturer designates
as dishwasher-proof.
■ Use a detergent which protects
utensils.
■ Take glass and cutlery out of
the dishwasher as soon as possible
after the programme ends.
14
Utensils aus
Loading the dishwasher
1. Remove large food remnants. It
is not necessary to prerinse utensils
under running water.
2. Place the utensils so that
– they are secure and cannot tip
over.
– all utensils with their openings
face down.
– parts with curves or indentations
are at an angle, thereby allowing
water to drain.
– does not obstruct rotation of the
two spray arms 12 and 1B.
Very small utensils should not be
washed in the machine, as they may fall
out of the baskets.
Upper basket
Arrange cups and glasses in the upper
basket 1*.
Note: Utensils must not be placed
above the tablet collecting tray 1:.
These may block the lid of the detergent
dispenser and prevent it from opening
fully.
Lower basket
Arrange pots and plates in the lower
basket 1Z.
* depending on the features of your
dishwasher
* depending on the features of your
dishwasher
15
aus Utensils
Tip: Heavily soiled utensils (pans)
should be placed in the lower basket.
The more powerful spray jet provides a
better dishwashing result.
Tip: Other examples, such as the best
way of loading your dishwasher, can be
found on our homepage. These can be
downloaded free of charge. The
corresponding Internet address can be
found on the back page of these
instructions for use.
Cutlery basket *
Cut l er y basket
Place cutlery, always unsorted with the
tips face down, in the cutlery basket *.
To prevent injuries, place long, pointed
implements and knives on the knife
shelf *.
You can take out the cutlery drawer.
Depending on the features of your
dishwasher, you can fold down the side
shelves to provide more room for taller
items of cutlery. The front rows of
prongs can be folded down to provide
room for wider handles.
* depending on the features of your
dishwasher
Cutlery drawer *
Cut l er y dr awer
Arrange the cutlery in the cutlery drawer
1" as illustrated. Separately arranged
utensils are easier to remove after
washing.
16
CLICK
* depending on the features of your
dishwasher
Utensils aus
Etagere *
Et a g e r e
The etagere and the space underneath
can be used for small cups and glasses
or for larger items of cutlery, such as
wooden spoons or serving cutlery. If
you do not require the etagere, it can be
folded up.
&/,&.
* Depending on the features of your
dishwasher, you can adjust the etagere
3 times the height.
Adjust the height of the etagere as
follows:
1. Position the etagere vertically and
pull upwards.
2. Push etagere at a slight angle
downwards to the required height
(1, 2, or 3).
3. Engage etagere.
Etagere “clicks” into position.
Folding spikes *
Fol d i n g spi kes
* Depending on the features of your
dishwasher, the spikes can be folded
down. This facilitates arrangement of
pots, bowls and glasses.
Fold down the spikes as follows:
1. Press lever forwards (1).
2. Fold down spikes (2).
Small items holder *
Small items hol der
* Depending on the features of your
dishwasher, the upper basket is fitted
with small items holders. The small
items holders can be used to securely
attach light plastic parts.
17
aus Utensils
Knife rack *
Kni f e rack
* Depending on the features of your
dishwasher, the upper basket is fitted
with a knife shelf. Long knives and other
utensils can be placed in the knife shelf.
Baking sheet spray head *
Baki ng sheet spray head
* depending on the features of your
dishwasher
Large trays or grilles as well as large
plates (gourmet plates, pasta plates,
dinner plates) can be cleaned with this
spray head.
Insert the spray head as follows:
1. Remove upper basket 1*.
2. Insert spray head as illustrated and
turn to the right.
Spray head is engaged.
18
To ensure that the spray jet can reach
all parts, arrange the baking sheets as
illustrated (max. 2 baking sheets and 2
grilles).
Note: Ensure that the dishwasher is
always operated with upper basket 1*
or baking tray spray head.
Utensils aus
Unloading the dishwasher
To prevent water from dripping off the
upper basket onto the utensils in the
lower basket, it is recommended
to empty the appliance from the bottom
up.
Tip: Hot utensils are sensitive to shock!
Therefore, when the programme ends,
leave the utensils to cool down in the
dishwasher until they can be handled.
Note: When the programme ends,
water droplets can still be seen inside
the appliance. This does not affect the
drying of the utensils.
Adjusting the height of the
basket *
Adj us t i n g the hei ght of the basket
* depending on the features of your
dishwasher
If required, the height of the upper
basket 1* can be adjusted to create
more space for taller utensils either in
the upper or lower basket.
Appliance height 81.5 cm
With cutlery basket Upper
basket
Setting 1 max. ø 22 cm 31 cm
Setting 2 max. ø 24.5 cm 27.5 cm
Setting 3 max. ø 27 cm 25 cm
Lower
basket
Appliance height 86.5 cm
With cutlery basket Upper
basket
Setting 1 max. ø 24 cm 34 cm
Setting 2 max. ø 26.5 cm 30.5 cm
Setting 3 max. ø 29 cm 28 cm
With cutlery drawer Upper
basket
Setting 1 max. ø 18 cm 34 cm
Setting 2 max. ø 20.5 cm 30.5 cm
Setting 3 max. ø 23 cm 28 cm
Arrange large plates up to a diameter of
31/34* cm in the lower basket 1Z as
illustrated.
Lower
basket
Lower
basket
With cutlery drawer Upper
basket
Setting 1 max. ø 16 cm 31 cm
Setting 2 max. ø 18.5 cm 27.5 cm
Setting 3 max. ø 21 cm 25 cm
Lower
basket
* depending on the features of your
dishwasher
19
aus detergent
Upper basket with side levers
1. Pull out upper basket 1*.
2. Hold the sides of the basket along
the upper edge.
This prevents it from suddenly
dropping.
3. To lower the upper basket; press in
both levers on the left and right on
the outside of the basket. The upper
basket lowers.
4. To lift the upper basket; grip the
sides of the upper basket along the
upper edge and lift.
5. Ensure that both sides of the upper
basket are at the same height.
6. Push in upper basket.
Upper basket with upper and
lower pairs of rollers
1. Pull out upper basket 1*.
2. Remove upper basket.
3. Re-attach upper basket to the upper
(Setting 3) or lower (Setting 1)
rollers.
. Detergent
det er gent
You can use tablets as well as powder
or liquid detergents for dishwashers, but
never use washing-up liquid. The
dosage can be individually adjusted
with powder or a liquid detergent
according to the degree of soiling.
Tablets contain an adequately large
amount of active ingredients for all
cleaning tasks. Modern, powerful
detergents predominantly use a
low-alkaline formulation with enzymes.
Enzymes break down starch and
remove protein. To remove coloured
stains (e.g. tea, ketchup), oxygen-based
bleaching agents are generally used.
Note: To ensure a good washing result,
always follow the instructions on the
detergent packaging!
If you have further questions,
we recommend that you contact
the detergent manufacturers’ helplines.
:Warning
Risk of injury and damage due to
non-observance of the safety
instructions for detergent and
rinse-aid products!
Always follow the safety instructions for
detergent products and rinse-aid
products.
4. Push in upper basket.
20
detergent aus
Adding detergent
1. If the detergent dispenser 1j is still
closed, actuate locking bar 9" to
open it.
2. Pour detergent into the dry detergent
dispenser 1j only (insert tablet flat,
not on its edge).
3. Dosage: see manufacturer’s
instructions on the packaging. Use
graduated detergent dispenser.
Usually 20 ml–25 ml are adequate
for normal soiling. If using tablets,
one tablet is adequate.
50 ml
25 ml
15 ml
4. Close cover on the detergent
dispenser.
Cover “clicks” into position.
CLICK
Tip: If the utensils are only lightly
soiled, slightly less than the indicated
amount of detergent is usually
adequate.
Suitable detergents and care products
can be purchased online via our
website or via customer service (see
back page).
Notes
■ If programmes are short, tablets
may not have full cleaning effect
due to different dissolving properties
and there may even be undissolved
detergent residue. It is
recommended to use washing
powder for these programmes.
■ The Intensive programme (on some
models) requires one tab only. When
using washing powder, you can
apply some of this cleaning agent
to the inside of the appliance’s door.
■ If using detergents in a water-soluble
protective cover: Take hold of the
cover with dry hands only and put
the detergent into an absolutely
dry detergent dispenser only,
otherwise the detergent may stick.
■ If you switch from combined
detergents to solo detergents,
ensure that the water softening
system * and amount of rinse aid
have been set to the correct value.
The detergent dispenser opens
automatically at the optimum time
depending on the programme. The
powder or liquid detergent is
distributed in the appliance and is
dissolved, the tablet falls into the
tablet collecting tray where it
dissolves in doses.
* depending on the features of your
dishwasher
21
aus Overview of programmes
/ Overview of programmes
Over vi ew of pr ogrammes
The max. possible number of programmes is illustrated in this overview. The
corresponding programmes for your appliance can be found on the fascia. The
programme data has been measured in the laboratory according to AS/NSZ 2007.
Note: The consumption figures depend on the selected programme and additional
functions. The programme duration will be different if the machine is short of rinse
additive or the function is turned off.
Type of utensils
and soiling
Pots, utensils and
cutlery
Highly soiled
Utensils and
cutlery
Normally soiled
non-sensitive
utensils and
cutlery
Highly soiled
Utensils and
cutlery
Normally soiled
Utensils and
cutlery
Normally soiled
Programme Programme data
Á
Auto Intensive
65° - 75°
Á / Ù
Auto Wash
45° - 65°
± / °
Super Wash 60°
â / à
Eco Wash
45°
ñ / ð
Quick 60 min.
65°
1.) Duration:
hs/mins
2.) Energy
consumption in
kWh
3.) Water
consumption in
litres
4.) With
Aquasensor
1.) 1:40 - 2:15
2.) 1,30 - 1,60
3.) -
4.) 11 - 15
1.) 1:45 - 2:55
2.) 0,95 - 1,60
3.) -
4.) 7 - 18
1.) 2:20
2.) 1,45
3.) 13
4.) -
1.) 2:50
2.) 0,64
3.) 12
4.) -
1.) 1
2.) 1,30
3.) 10
4.) -
Possible
additional
options
all
all
all
all
Extra Dry
Programme sequence
Sensor-controlled:
Is optimised according
to the soiling with the aid
of sensors.
Intensiv:
Clean 60°
Intermediate rinse
Final rinse 72°
Dry
Most economical
programme:
Prerinse
Clean 45°
Intermediate rinse
Final rinse 45°
Dry
Time-optimised:
Clean 65°
Intermediate rinse
Final rinse
Dry
22
Overview of programmes aus
Type of utensils
and soiling
Utensils and
cutlery
Lightly soiled
all types
of utensils
Lightly soiled
-
--------
Programme Programme data
ñ / ð
Quick 29 min.
45°
ù / ø
Prerinse
‰ / Š
Machine Care
Programme selection
1.) Duration:
hs/mins
2.) Energy
consumption in
kWh
3.) Water
consumption in
litres
4.) With
Aquasensor
1.) 0:29
2.) 0,80
3.) 10
4.) -
1.) 0,15
2.) 0,05
3.) 4
4.) -
1.) 1:30
2.) 0,90 - 1,06
3.) 9,5 - 12,5
4.) -
Possible
additional
options
Extra Dry
none
none
Programme sequence
Time-optimised:
Clean 45°
Intermediate rinse
Final rinse 55°
Cold rinse:
Prerinse
Machine cleaning
cycle 70°
You can select a suitable programme
according to the type of utensils and
type of soiling.
Information for test institutes
Test institutes can request the
conditions for running comparison tests
by sending an e-mail to
dishwasher@test-appliances.com.
Quote the appliance number (ENr.)
and the production date (FD) which you
can find on the rating
plate 9* on the appliance door.
23
aus Additional functions
0 Additional functions
Addit i onal functions
* Depending on the features of your
dishwasher, you can select different
additional functions H.
Ÿ Speed Perfect *
Speed Per f ec t
This function can reduce the running
time by approx. 20% to 50% depending
on the selected rinse programme. To
obtain optimum cleaning and drying
results at a reduced running time, water
and energy consumption are increased.
§ Half load *
Hal f l oad
If you have only a few items to wash
(e.g. glasses, cups, plates), you can
switch to “half load”. This will save
water, energy and time. It is
recommended to put a little less
detergent in the detergent dispenser
than for a full load.
μ hygienePlus
(HygienePlus) *
hygi enePl us ( Hygi enePlus )
This function increases the
temperatures and retains them for an
extra long time to obtain a defined
disinfection performance. Continuous
use of this function increases the
hygiene status. This additional option is
ideal for cleaning e.g. chopping boards
and baby bottles.
Ï intensiveZone *
i nt ensi veZone
Perfect for a mixed load. You can wash
very soiled pots and pans in the lower
basket together with normally soiled
utensils in the upper basket. The spray
pressure in the lower basket
is intensified, the rinsing temperature
is increased slightly.
¿ Extra Dry *
Ext ra Dr y
An increased temperature during the
final rinse and an extended drying
phase ensure that even plastic parts dry
better. There is a slight increase in the
energy consumption.
24
Operating the appliance aus
1 Operating the
appliance
Operat i ng the appl i ance
AquaSensor *
AquaSensor
* depending on the features of your
dishwasher
The Aqua sensor is an optical
measuring device (light barrier) which
measures the turbidity of the rinsing
water.
The AquaSensor is used according
to the programme. If the AquaSensor is
active, “clean” rinsing water can be
transferred to the next rinse bath and
water consumption can be reduced by
3–6 litres. If the turbidity is greater,
the water is drained and is replaced
with fresh water. In the automatic
programmes the temperature
and running time can also be adjusted
to the degree of soiling.
Switching on the appliance
1. Turn tap fully on.
2. Switch on ON/OFF switch (.
The displays for the last programme
and last additional function selected
flash. These settings will be retained
unless another 0 programme key
is pressed. The expected
programme duration flashes on the
digital display h.
3. Press the START button P.
Programme sequence starts.
Remaining running time
display
When the programme is selected, the
remaining programme time is indicated
in the display window h.
The running time is determined during
the programme by the water
temperature, the quantity of dishes as
well as the degree of soiling and may
vary (depending on the selected
programme).
Time preselection *
Ti me pr esel ect i on
* depending on the configuration of
your specific dishwasher
You can delay the start of the
programme in hourly steps by up to 24
hours.
Here’s how to set up the delay:
1. Switch on ON/OFF switch (.
2. Press the timer programming button
@ + repeatedly until h œ ‹‚
appears in the display window.
3. Keep pressing the timer
programming button @ - or + until
the desired time is displayed.
4. Press START button P.
The delay timer has been activated.
5. To clear the specified delay, press
the button @ - or + repeatedly until
h œ ‹‹ appears in the display
window.
Until the programme has started, you
can change your selection in any way
you like.
25
aus Operating the appliance
Programme end
The programme has finished when the
value ‹:‹‹ appears in the display
window h.
Auto Power Off (Automatic
switch off after end of
programme)
Aut o Po wer Of f
To save power you can set the
dishwasher to switch off automatically
from 1 minute to 120 minutes after the
end of its programme. You can choose
a setting from ˜:‹‹ to ˜:‹ƒ.
˜:‹‹ Appliance does not switch off
automatically.
˜:‹‚ Appliance switches off after 1
minute.
˜:‹ƒ The appliance switches off after
120 minutes.
Here’s how to change the setting:
1. Switch on ON/OFF switch (.
2. Hold down the programme button
# and then repeatedly press the
START button P until š:‹...
appears in the display window.
3. Release both buttons.
The LED of the # button flashes
and the digital display h lights up
to show the value š:‹....
4. Press the programme button #
repeatedly until the value ˜:‹...
appears in the display window h.
5. Press the programme button 3.
Each time the button is pressed, the
set value increases by one level;
when it reaches the value ˜:‹ƒ the
display jumps back to ˜:‹‹.
6. Press START button P.
The set value is saved.
Switching off the appliance
Shortly after the end of the
programme:
1. Switch off ON/OFF switch (.
2. Turn off water supply (does not
apply to appliances with Aqua-Stop).
3. Remove the utensils when they have
cooled down.
Note: When the programme ends,
leave the appliance to cool down a
while before opening it. This will prevent
steam from escaping and causing
long-term damage to your built-in
furniture.
Interrupting the programme
Caution!
Expansion (overpressure) may cause
the appliance door to jump open and/or
water to escape! If the door was opened
on an appliance which has a hot water
connection or is heated, always leave
the door ajar for several minutes and
then close it.
1. Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
2. Switch on the ON/OFF switch (
again to continue the programme.
26
Cleaning and maintenance aus
Terminating the programme
(Reset)
Ter minating the progr amme
1. Press the START button P and
hold it down for about 3 seconds.
The value ‹:‹‚ appears in the
display window h. The
programme sequence lasts about
1 minute. The value ‹:‹‹ appears in
the display window h.
2. Switch off ON/OFF switch (.
Changing the programme
When the START button P has been
pressed, the programme cannot be
changed. The only way a programme
can be changed is by Cancel
programme (Reset).
ExtraDry
The final rinse uses a higher
temperature which improves the drying
result. The running time may increase
slightly. (Be careful if you have delicate
tableware)
Here’s how to change the setting:
1. Switch on ON/OFF switch (.
2. Hold down the programme button
# and then repeatedly press the
START button P until š:‹...
appears in the display window h.
3. Release both buttons.
4. By pressing the 3 button you can
switch intensive drying on š:‹‚ or
off š:‹‹.
5. Press START button P.
The set value is saved.
2 Cleaning and
maintenance
Cl eani ng and mai nt enanc e
A regular inspection and maintenance
of your machine will help to prevent
faults. This saves time and prevents
problems.
Overall status of the
dishwasher
*The interior of your dishwasher is
predominantly self-cleaning. In order to
remove deposits, your dishwasher
automatically changes the running of
the programme (such as by increasing
the cleaning temperature) at certain
intervals. This will lead to higher
consumption values when running this
programme.
*Depending on the features of your
dishwasher
If you should find deposits in the
interior of the dishwasher in spite of
this, remove these deposits as
follows:
1. Fill the detergent dispenser 1j with
detergent.
2. Select the programme with the
highest temperature.
3. Start the programme without dishes.
:Warning
Health hazard due to detergents
containing chlorine!
Always use chlorine-free detergents.
27
aus Cleaning and maintenance
Notes
■ Only clean the appliance with
special detergents/appliance
cleaners which are suitable for use
with dishwashers.
■ Regularly wipe the door seals using
a damp cloth and a little washing-up
liquid. This will keep the door seal
clean and hygienic.
■ Leave the door open slightly if the
appliance will not be used for a
while. This will prevent an unpleasant
odour from developing.
■ Never clean the dishwasher using a
steam cleaner. The manufacturer
is not liable for any consequential
damage.
■ Wipe the front of the dishwasher and
the control panel regularly using a
damp cloth and a little washing-up
liquid.
■ Do not use sponges with a rough
surface or abrasive detergents.
These could scratch the surface.
■ For dishwashers with a stainless
steel front, avoid using sponge
cloths, or rinse these thoroughly
several times before using them for
the first time. This will prevent
corrosion.
Machine Care ‰ *
Machine Ca r e
Machine Care used in combination with
commercially available machine
cleaning detergent is a suitable
programme for cleaning your
dishwasher. Deposits such as grease
and limescale can cause your
dishwasher to malfunction. In order to
avoid such faults and to reduce the
development of odours, we recommend
cleaning the dishwasher at regular
intervals.
* As soon as the Machine Care display
lights up in the control panel, or you are
advised to do so on the front display,
run the Machine cleaning programme
Machine Care without loading any
tableware. After you have run the
Machine Care the display in the control
panel will go out.
If your dishwasher does not have a
reminder function, follow the instructions
for use on the machine cleaning
detergents.
28
Cleaning and maintenance aus
Notes
■ Remove any coarse soiling in the
interior using a damp cloth.
■ Run the programme without dishes,
and in combination with a machine
cleaning detergent.
■ Use a special machine cleaning
detergent, and not dishwasher
detergent.
■ Observe the safety instructions and
the instructions for use on the
machine cleaning detergent
packaging.
■ *After three rinse cycles, the display
in the control panel will go out
automatically, even if you have not
run the Machine cleaning cycle
programme.
* depending on the features of your
dishwasher
Rinse aid
Fill the rinse aid as soon as the refill
indicator ` lights up in the control
panel.
Filters
The filters 1J keep large foreign
objects in the rinsing water away from
the pump. hese foreign objects may
occasionally block the filters.
The filter system consists of
■ a coarse filter
■ a flat fine filter
■ a microfilter
1. After each washing cycle check
the filters for residue.
2. Unscrew filter cylinder as illustrated
and take out filter system.
3. Remove any residue and clean
filters under running water.
4. Re-install filter system in reverse
sequence and ensure that the arrow
marks are opposite each other after
closing the filter system.
29
aus Fault, what to do?
Spray arms
Limescale and contaminants in the
rinsing water may block nozzles and
bearings on the spray arms 12 and
1B.
1. Check outlet nozzles on the spray
arms for blockages.
2. Unscrew the upper spray arm 12
(1) and remove downwards (2).
3. Remove the lower spray arm 1B
upwards.
3 Fault, what to do?
Faul t , wh at to do?
Experience has shown that you can
rectify most faults which occur in daily
operation yourself. This ensures that the
appliance is quickly available to you
again. In the following overview you can
find possible causes of malfunctions
and helpful information for rectifying
them.
Note: If the appliance stops during
dishwashing or does not start for no
obvious reason, first run the Abort
programme function (Reset)
~ "Operating the appliance"
on page 25.
:Warning
Improper
repairs or use of non-original spare
parts may cause considerable damage
and put the user at considerable risk!
Always have repairs carried out by
technicians. If a component has to be
replaced, always use original spare
parts.
4. Clean spray arms under running
water.
5. Re-engage or screw on spray arms.
30
Fault, what to do? aus
Waste water pump
Large food remnants or foreign objects
which were not captured by the filters
may block the waste water pump. The
rinsing water will then be above the
filter.
:Warning
Danger of cutting!
Sharp and pointed objects or glass
fragments may block the waste water
pump.
Always carefully remove foreign objects.
Clean the waste water pump as
follows:
1. Disconnect the dishwasher from the
power supply.
2. Take out top basket 1* and bottom
basket 1Z.
3. Remove the filters 1J.
4. Scoop out water, use a sponge if
required.
5. Prise off the pump cover (as shown)
using a spoon. Grip the pump cover
by the crosspiece and lift diagonally
inwards (1). Remove cover
completely.
6. Check impeller wheel and remove
any foreign objects.
7. Place pump cover in the original
position (2) and press down until it
engages (3).
CLICK
8. Install filters.
9. Re-insert baskets.
1
31
aus Fault, what to do?
Fault table
Fault Reason Solution
“Check water supply”
display X lights up.
Fault code “:‹ˆ is lit. Intake opening (on right inside of
Fault code “:‚ƒ is lit. Heating element soiled. Clean appliance with dishwasher cleaning
Fault code “:‚… is lit. Water protection active. Turn off tap.
Fault code “:‚† is lit.
Fault code “:‚‡ is lit. Constant water supply.
Fault code “:ƒƒ is lit. Filters 1J are soiled or
Fault code “:ƒ… is lit. Wastewater hose kinked or
Fault code “:ƒ† is lit. Wastewater pump blocked or
Supply hose kinked. Install supply hose without kinks.
Tap turned off. Turn on the tap.
Tap jammed or calcified. Turn on the tap.
Filter in the water supply blocked. Switch off the appliance and pull out the
appliance) covered by utensils.
blocked.
blocked.
Siphon connection still sealed. Check connection to siphon and open if
Cover on the wastewater pump
loose.
cover on the wastewater pump is
not locked in position.
Flow rate must be at least 10 l/min. when
water supply is open.
mains plug. Turn off the tap. Unscrew
water connection.
Clean filter in the supply hose. Screw
water connection on again. Check for
leaks. Reconnect power supply. Switch on
the appliance.
Arrange utensils so that the intake
opening is not obstructed.
agent.
Call customer service and quote the fault
code.
Clean filters.~ "Filters" on page 29
Install hose without kinks, remove any
residue.
required.
Lock cover correctly.~ "Waste water
pump" on page 31
Clean pump and lock cover correctly.
~ "Waste water pump" on page 31
32
Fault, what to do? aus
Fault Reason Solution
Fault code “:ƒˆ is lit. Mains voltage too low. No appliance fault, have the mains voltage
A different fault code is
indicated on the digital
display.
(“:‹‚ to “:„‹)
p or • appears on the
digital display h. *
Refill indicator for rinse aid
` is lit.
Refill indicator for rinse aid
` is not lit.
Water is left in the
appliance at the end of the
programme.
A technical fault has probably
occurred.
Not a fault! See TurboSpeed 20 min. in the chapter
No rinse aid. Refill rinse aid.
Refill indicator switched off. Activation/Deactivation. ~ Page 13
There is still enough special rinse
aid available.
Filter system or area under the
filters 1J is blocked.
Programme not finished yet Wait until programme ends or reset (see
and electrical installation checked.
Switch off the appliance with the ON/OFF
switch (.After a short time, restart the
appliance.
If the problem recurs, turn off the tap and
pull out the mains plug.
Call customer service and mention the
fault code.
“Overview of programmes”. *
Check the filling level, refill indicator.
Clean filters and area underneath (see
“Waste water pump”).
“Terminating the programme”).
33
aus Fault, what to do?
Fault Reason Solution
Utensils not dry. Not enough rinse aid in the
dispenser, or none at all.
Programme without drying was
selected.
Water collecting in depressions
on the utensils and cutlery.
Refill rinse aid.
Select programme with drying.
Arrange utensils in a sloping position,
arrange affected utensils as sloping as
possible.
The combined detergent used
has a poor drying performance.
Intensive drying to increase
drying not activated.
Utensils were removed too early
or drying process had not ended
yet.
The eco rinse aid used has a poor
drying performance.
Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity
Cutlery not dry. Cutlery not arranged properly in
Appliance interior wet after
rinse cycle.
the cutlery basket.
Cutlery not arranged properly in
the cutlery drawer.
No appliance fault. On account of the “Condensation drying”
Use different combination detergent with
better drying performance. Use of rinse
aid also improves the drying performance.
Activate intensive drying. ~ "Operating
the appliance" on page 25
Wait until the programme ends, or wait
until 30 minutes after the end of the
programme before removing the utensils.
Use a name-brand rinse aid. Eco products
are much less effective.
and therefore dries less well.
Separate cutlery if possible, prevent
contact points.
Arrange cutlery properly and separate if
possible.
principle, water droplets are physically
induced and required in the container.The
humidity in the air condenses on the inner
walls of the dishwasher, drains and is
pumped out.
34
Fault Reason Solution
Food remnants on the
utensils.
Detergent residue Detergent dispenser cover 1j
Utensils placed too closely
together, utensils basket
overfilled.
Spray arm rotation obstructed. Arrange utensils so that the spray arm can
Spray arm nozzles are blocked. Clean the spray arm
Filters 1J dirty. Clean filters. ~ "Cleaning and
Filters 1J inserted incorrectly
and/or not engaged.
Rinse programme too weak. Select a more intensive rinse programme.
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Tall narrow receptacles in corner
areas are not rinsed adequately.
Top basket 1* on right and left
not set to same height.
blocked by utensils and therefore
does not open fully.
Detergent dispenser cover 1j
blocked by the tablet.
Tablets used in the quick or short
programme.
Dissolving time of the detergent
is not reached in the selected
short programme.
Washing effect and dissolving
performance are reduced after a
prolonged storage time or
detergent is very lumpy.
Arrange utensils with adequate clearance
between them ensuring that the spray jets
can reach the surface of the utensils.
Prevent contact points.
rotate without obstruction.
nozzles.~ "Cleaning and maintenance"
on page 27
maintenance" on page 27
Insert and engage filters correctly.
Do not prerinse utensils.Remove only
large food remnants.
Do not place tall narrow receptacles too
obliquely and do not place in the corner
area.
Set top basket to same height using side
levers.
Utensils must not be placed above the
tablet collecting tray 1:.These may
block the lid of the detergent dispenser
and prevent it from opening fully.
~ "Upper basket" on page 15
Do not place utensils or fragrance
dispenser in the tablet collecting tray.
Tablet must be inserted flat and not
upright.
Dissolving time of tablets too long for a
quick or short programme.
Use a detergent powder or select a more
intensive programme.
Change detergent.
Fault, what to do? aus
35
aus Fault, what to do?
Fault Reason Solution
Water stains on plastic
parts.
Washable or water-soluble
coatings in the container or
on the door.
White, stubborn coatings;
limescale on the utensils,
container or door.
Tea or lipstick residue on
the utensils.
Coloured (blue, yellow,
brown), difficult to remove
to non-removable coatings
in the appliance or on
stainless steel utensils.
Discolouration of the
plastic parts inside the
appliance.
Droplet formation on plastic
surface is physically unavoidable.
After drying, water stains are
visible.
Detergent substances are
deposited. These coatings cannot
usually be removed with
chemicals (appliance cleaner, ...).
Only for glasses: Initial glass
corrosion – can only apparently
be wiped off.
Detergent substances are
deposited. These coatings cannot
usually be removed with
chemicals (appliance cleaner, ...).
Underdosing of detergent. Increase detergent dosage or change
Rinse programme selected too
weak.
Rinsing temperature too low. Select programme with higher rinsing
Too little or unsuitable detergent. Use suitable detergent at correct dosage.
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Film formation consisting of
ingredients from vegetables (e.g.
cabbage, celery, potatoes,
noodles, ...) or the tap water (e.g.
manganese).
Film formation caused by metallic
components on silver or
aluminium utensils.
Plastic parts inside the appliance
may become discoloured during
the service life of the dishwasher.
Use a more intensive programme (more
water changes).
Arrange utensils in a sloping position.
Use rinse aid.
Change detergent brand.
Clean appliance mechanically.
See “Glass and utensil damage”
~ Page 14.
Change detergent brand.
Clean appliance mechanically.
detergent.
Select a more intensive rinse programme.
temperature.
Do not prerinse utensils.Remove only
large food remnants.
Can be partly removed with machine
cleaner or by mechanical cleaning.
Coatings are harmless.
Can be partly removed with machine
cleaner or by mechanical cleaning.
Discolouration is normal and will not
impair the function of the dishwasher.
36
Fault, what to do? aus
Fault Reason Solution
Plastic parts discoloured. Rinsing temperature too low. Select programme with higher rinsing
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Removable streaks on
glasses, glasses with
metallic appearance and
cutlery.
Initial or existing,
irreversible clouding of
glass.
Rust spots on the cutlery. Cutlery is not sufficiently
Appliance cannot be
switched on or operated.
Too much rinse aid. Set rinse aid amount to lower setting
No rinse aid added or setting too
low.
Detergent residue in the final
rinse. Detergent dispenser cover
blocked by utensils (cover does
not open fully).
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Glasses not dishwasher-proof,
only suitable for dishwasher.
rust-resistant.Knife blades are
frequently more severely
affected.
Cutlery will also rust if rusting
parts are rinsed at the same time
(pan handles, damaged utensil
baskets, etc.).
Malfunction. Disconnect appliance from the power
temperature.
Do not prerinse utensils.Remove only
large food remnants.
setting.
Add rinse aid and check dosage
(recommended Level 4–5).
Detergent dispenser cover must not be
obstructed by utensils.
Do not place utensils or fragrance
dispenser in the tablet collecting tray.
Do not prerinse utensils.Remove only
large food remnants.
Use dishwasher-proof glasses.
Avoid long steam phase (standing time
after rinse cycle ends).
Use rinse cycle at lower temperature.
Use detergent with glass protection
component.
Use rust-resistant cutlery.
Do not wash rusting parts.
supply; pull out the mains plug or switch
off the fuse. Wait at least 5 seconds, then
connect the appliance to the power
supply.
37
aus Fault, what to do?
Fault Reason Solution
Appliance does not start. The mains fuse has tripped. Check mains fuse.
Power cord not inserted. Ensure that the power cord is plugged all
The appliance door has not been
shut properly.
Programme starts
automatically.
The door is difficult to
open.
Door cannot be closed. Door lock has been activated. Close door with increased force.
Cover on the detergent
dispenser cannot be
closed.
Detergent residue in the
detergent dispenser or in
the tablet collecting tray.
Appliance stops during the
programme or programme
is interrupted.
Filling valves making
striking noises.
You did not wait until programme
ended.
Child-proof lock is activated. Deactivate child-proof lock.(See
Door cannot be closed due to
installation.
Detergent dispenser or cover
guide blocked by sticky detergent
residue
Spray arms blocked by utensils,
therefore detergent is not rinsed
out.
The detergent dispenser was
damp when filled.
Door not closed properly. Close the door.
Do not place utensils or fragrance
dispenser in the tablet collecting
tray.
Top basket presses against the
door and prevents door from
being closed securely.
Power and/or water supply
interrupted.
Depends on domestic installation,
as appliance is not defective. No
effect on appliance function.
the way into the back of the appliance and
into the socket. Check that the socket
functions.
Close the door.
Perform reset.
(See “Terminating the programme”)
instructions for use at the back)
Check appliance installation: Door or
attached parts must close without
obstruction.
Remove detergent residue.
Ensure that the spray arms can rotate
freely.
Pour detergent into the dry detergent
dispenser only.
Check whether rear panel is being
pressed in, e.g. by socket or by hose
holder which has not been removed.
Restore power and/or water supply.
No remedial action possible.
38
Fault Reason Solution
Knocking or rattling noise. Spray arm strikes the utensils,
utensils not positioned correctly.
If there is a low load, the water
jets strike the washing tank
directly.
Light utensils move during the
Position utensils so that the spray arms do
not strike the utensils.
Load the appliance with more utensils or
distribute the utensils more evenly in the
dishwasher.
Arrange light utensils securely.
rinse cycle.
Unusual foam formation. Hand washing-up liquid in the
rinse aid dispenser.
Immediately refill rinse aid dispenser with
rinse aid.
Rinse aid spilled. Remove rinse aid with a cloth.
--------
Fault, what to do? aus
39
aus Customer service
4 Customer service
Cus t omer ser vi ce
If you are unable to rectify the fault,
please contact your customer service.
We will always find an appropriate
solution in order to avoid unnecessary
visits by engineers. Contact information
for your nearest customer service can
be found on the back of these
instructions for use or on the enclosed
customer service list. When calling,
please state the appliance number
(E-Nr. = 1) and the production number
(FD = 2) which can be found on the
rating plate 9* on the appliance door.
(1U
Trust the expertise of the
manufacturer. Contact us for
assistance. You can therefore be sure
that the repair is carried out by trained
service technicians who carry original
spare parts for your domestic
appliances.
)'
5 Installation and
connection
Install ation and connect i on
The dishwasher must be connected
correctly, otherwise it will not function
properly. The specifications for the inlet
and outlet as well as the electrical
connected loads must correspond with
the required criteria as
specified in the following paragraphs
or in the installation instructions.
Install the appliance in the correct
sequence:
1. Checking appliance on delivery
2. Installation
3. Drainage connection
4. Drinking water connection
5. Electrical connection
Contents of package
If you have any complaints, contact the
dealer from whom you purchased the
appliance or our customer services.
■ Dishwasher
■ User manual
■ Installation instructions
■ Quick reference guide*
■ Warranty*
■ Installation materials
■ Steam guard plate*
■ Rubber apron*
■ Power cord
40
* depending on the features of your
dishwasher
Safety instructions
Please follow the safety instructions
under ~ "Installation" on page 5.
Installation and connection aus
Delivery
Your dishwasher has been checked
thoroughly in the factory to ensure that
it is in working order. This may cause
small water stains. These will disappear
after the first wash cycle.
Technical specifications
■ Weight:
up to 60 kg
■ Voltage:
220–240 V, 50 Hz or 60 Hz
■ Connected load:
2000 - 2400 W.
■ Fuse:
10/16 A (UK 13 A).
■ Power input:
Off mode (Po)* 0.10 W.
Left On mode (Pl)* 0.10 W.
*according to regulations (EU) nos.
1016/2010 and 1059/2010.
Additional functions and settings
may increase the power
consumption.
■ Water pressure:
at least 0.05 MPa (0.5 bar),
maximum 1 MPa (10 bar).
At a higher water pressure:
connect pressure-reducing valve
ahead.
■ Inlet rate:
minimum 10 litres/minute
■ Water temperature:
cold water.
Hot water:
Maximum temperature 60 °C.
■ Capacity:
12–15 place settings (depending on
the features of your dishwasher).
Installation
The required installation dimensions
can be found in the installation
instructions. Level the appliance with
the aid of the height-adjustable feet.
Ensure that the appliance is situated
securely on the floor.
■ A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
secured to prevent it from
overturning, e.g. by screwing it to the
wall or by installing it under a
continuous worktop which is
screwed to adjacent cupboards.
■ The appliance can easily be installed
in a fitted kitchen between wooden
and plastic walls.
Drainage connection
1. The required work sequence can be
found in the installation instructions.
If required, fit a siphon with an
drainage connection.
2. Connect the waste-water hose
to the drainage
connection of the siphon with
the enclosed parts.
Ensure that the drainage hose is not
kinked, crushed or twisted and that
there is no cover
plate in the drainage to prevent
the waste water from flowing out!
41
aus Installation and connection
Drinking water connection
1. Fasten the drinking water connection
to the tap according
to the installation instructions using
the enclosed parts.
Ensure that the drinking water
connection is not kinked, crushed
or twisted.
2. When replacing the appliance,
always use a new water supply
hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum 1
MPa (10 bar).
At a higher water pressure:
connect pressure-reducing valve ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water.
Hot water:
Maximum temperature 60 °C.
Warm water connection*
Hot wat er c onnect i on
* depending on the configuration of
your specific dishwasher
The dishwasher can be connected to
cold or hot water up to max. 60°C.
Connection to hot water is
recommended if the hot water can be
supplied by energetically favourable
means and from a suitable installation,
e.g. solar heating system with
circulation line. This will save energy
and time. The hot water setting ‘:‹‚
allows you to adjust your appliance
optimally to operation with hot water. It
is recommended to have a water
temperature (temperature of the
incoming water) of at least 40 °C and
no more than 60 °C. It is not
recommended to connect the appliance
to hot water if the water is supplied from
an electric boiler.
Here’s how to change the hot water
setting:
1. Switch on ON/OFF switch (.
2. Hold down the programme button
# and then repeatedly press the
START button P until š:‹...
appears in the display window.
3. Release both buttons.
The LED of the # button flashes
and the digital display h lights up
to show the value š:‹....
4. Press the programme button #
repeatedly until the factory setting
value ‘:‹‹ appears in the display
window h.
5. By pressing the 3 button, you can
switch the hot water setting off ‘:‹‹
or on ‘:‹‚.
6. Press START button P.
The set value is saved.
42
Installation and connection aus
Electrical connection
■ Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing 9*.
■ The socket must be near the
appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side to
satisfy the relevant safety
instructions.
■ The connection may be modified
by technicians only.
■ A power cord extension may be
purchased from customer service
only.
■ Use only a residual current operated
circuit-breaker which features the
symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
■ The appliance features a water
damage protection system. Please
note the system will function only
when the power supply
is connected.
Removal
Also observe
the sequence of worksteps here.
1. Disconnect the appliance from the
power supply.
2. Turn off the tap.
3. Undo the waste water and drinking
water connection.
4. Loosen fastening screws for the
furniture parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully
pulling the hose behind.
Transporting
Empty the dishwasher and secure loose
parts.
Drain the appliance according to the
following steps:
1. Turn on water supply.
2. Switch on ON/OFF switch (.
3. Select programme with the highest
temperature.
The estimated programme duration
appears in the display window h.
4. Press START button P.
Programme sequence starts.
5. After about 4 minutes, repeatedly
press the START button P until
‹:‹‚ appears in the display window.
After about 1 minute the display
window will show ‹:‹‹.
6. Switch off ON/OFF switch (.
7. Turn off water supply, disconnect
supply hose and drain water.
Note: Always transport the dishwasher
upright. This prevents residual water
from getting into the machine’s controls
and causing the programme sequence
to malfunction.
Protection against frost
Prot ec t i on agai nst frost (Empt y i ng the appl i ance)
If the appliance is in a room where
there is a risk of frost (e.g. holiday
home), empty the appliance completely
(see Transportation).
6XEMHFWWRFKDQJHV
43
AquaStop guarantee
In addition to warranty claims against the seller based on the purchase contract
and in addition to our appliance warranty we will pay damages under
the following conditions:
1.
If our AquaStop system is defective and causes water damage,
we will make good the damage for private users.
To ensure water damage protection, the appliance must be connected
to the power supply.
2.
This liability guarantee is valid for the service life of the appliance.
3.
A prerequisite for the warranty claim is that the appliance has been correctly
installed and connected with AquaStop according to our instructions.
This also includes the correct installation of the AquaStop extension
(original accessory). Our warranty does not extend to defective
feed lines or fittings up to the AquaStop connection on the tap.
If your appliance is fitted with AquaStop, you can leave your appliance
4.
unattended during operation and leave the tap turned on afterwards.
The tap should only be turned off if you are absent from home for
a prolonged period, e.g. several weeks holiday.
(does not apply to appliances without AquaStop)
Repair order and advice on faults.
GB 0344 892 8979
IE 01450 2655
US 800 944 2904
Contact information for all countries can be found on the enclosed customer service list.
Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.
0.03 € per minute at peak. Off peak 0.0088 € per minute.
toll-free
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
*9001244085*
9001244085
(9712) 642 MA
Loading...