Bosch S47KMK35UC/25, S47KMK15UC/22 Installation Guide
Installation Guide
Instrucciones de Instalaci6n
instructions dlnstallation
English / Espafiol/Frangais
ModeJs/Modelos/Mod_le$: 630.1399", 630.1300% 630.1302"
I<enmoreElJte
S H®o
Ge ...... Ge
P/N 9000531215 Rev. A
Sears Brands Management Corporation
Hofl:man Estates, IL 60179 USA
www.kenmore.com
www.sears.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8
www.sears.ca
Dishwasher Safety ....................................................... 2-3
Tools needed ................................................................................ 4
Materials supplied ...................................................................... 4
Pre-install instructions ................................................................. 5
Electrical requirements ............................................................... 6
Inlet Water connections .............................................................. 7
Drain connection .......................................................................... 8
Rubber Drain Hose Adaptor ................................................... 9
Mounting Brackets ...................................................................... 9
Leveling the Dishwasher ............................................................ 10
Attaching the Toe Panel ............................................................ 11
To avoid possible injury or property damage, OBSERVE ALL
WARNINGS AND CAUTIONS. These instructions are intend-
ed for use by qualified installers only. In addition to these
instructions, the dishwasher shall be installed to meet all
electrical and plumbing codes and ordinances (both national
and local).
Avoiding General Hazards
Do not use the dishwasher until it is completely installed. When
opening the door on an uninstalled dishwasher, carefully open
the door while supporting the rear of the unit. Failure to follow
this warning can cause the dishwasher to tip over and result
in serious iniury.
In some conditions, hydrogen gas can form in a hot water system
that has not been used for weeks. Hydrogen gas is explosive.
Before filling a dishwasher from a system that has been off for
weeks, run the water from a nearby faucet in a well ventilated
area until there is no sound or evidence of gas.
Temperatures required for soldering and sweating will damage
the dishwasher's base and water inlet valve. If plumbing lines
are to be soldered or sweated, keep the heat source at least
6 inches (152.4 mm) away from the dishwasher's base and
water inlet valve.
Removing any cover or pulling the dishwasher from the cabinet
can expose hot water connections, electrical power and sharp
edges or points. Handle with care. Always wear gloves and
safety glasses.
_Avoiding Flectrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to touch.
Separate channels are provided under the dishwasher.
Do not work on an energized circuit. Doing so could result
in serious injury or death. Only qualified electricians should
perform electrical work. Do not attempt any work on the
dishwasher electric supply circuit until you are certain the circuit
is de-energized.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with all
national and local electrical codes and ordinances. The
dishwasher is designed for an electrical supply of 120V,
60 Hz, AC, connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker rated for
15 amps. Electrical supply conductors shall be a minimum
#14 AWG copper only wire rated at 75°C (167°F) or
higher.
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance. Do not use extension cords.
_ Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water line.
Serious iniury could result. Only qualified plumbers should
perform plumbing work. Do not attempt any work on the
dishwasher hot water supply plumbing until you are certain
the hot water supply isshut off.
Do not overtighten the 90 ° elbow. Doing so may damage
the water inlet valve and cause a water leak.
Temperatures required for soldering and sweating will
damage the dishwasher's water inlet valve. If plumbing
lines are to be soldered or sweated, keep the heat source
at least 6 inches (152.4 mm) away from the dishwasher's
water inlet valve.
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be done in
accordance with national and local codes.
These instructions depict an installation method for stainless
steel braided hose or PEX hot water supply lines. If using
copper tubing or other material for water supply, defer to
a licensed plumber for proper installation.
2
Readthese installatlon instructions completely and
Follow them carefully. They will save you time and
effort and help to ensure safety and optimum dishwasher
performance.
if the dishwasher is installed in a Iocatlon that experiences
Freezing temperatures (e.g., in a holiday home), you must
drain all the water from the dishwasher's interior. Water
system ruptures that occur as a result of freezing are NOT
COVERED BY WARRANTY.
IMPORTANT
• The dishwasher drain hose must be installed with a
portion of it at least 20" (508mm) above the cabinet
floor; otherwise the dishwasher may not drain properly.
• This dishwasher is intended far indoor residential use
only, and should not be used in commercial food service
establishments.
OTHER iMPORTANT iNFORMATiON
• This dishwasher isdesigned to be enclosed on the top
and both sides by cabinetry.
NEW iNSTALLATiON - if the dishwasher is a new
installation, most of the work must be done before the
dishwasher is moved into place.
REPLACEMENT - if the dishwasher is replacing another
dishwasher, check the existing dishwasher connections for
compatibility with the new dishwasher, and replace parts
as necessary.
• This appliance has been found to be in compliance with
CAN/CSA-C22.2 No. 167/UL 749. it isthe responsibility
of the owner and the installer to determine if
additional requirements and standards apply in specific
installations.
Nat far outdoor use.
Before installing the _L'-shaped supplied countertop
mounting brackets (select models), decide which method
will be used to secure the dishwasher into its opening. Once
these mounting brackets are insta!led on the dishwasher,
removing them is difficult and will damage the mounting
brackets and the dishwasher.
Electrical Supply Cable - Minimum #14 AWG
2 conductor, 1 ground, insulated copper
conductors rated 75°C (167°F) or higher.
inspect the Dishwasher
After unpacking the dishwasher and prior to installation,
thoroughly inspect the dishwasher for possible freight or
cosmetic damage. Report any damage immediately by
calling 1-800-4-MY-HOME. Cosmetic defects must be
reported within 30 days of installation.
NOTE: Do not discard any bags or items that come with
the original package until after the entire installation has
been completed.
Shut-off valve and fittings appropriate
for hot water supply line (copper tubing/
compression fitting, or braided hose).
Hot Water Supply Line - Minimum 3/8"
(0.95cm) O.D. copper tubing, PEX, or metal
braided dishwasher supply line.
Shut-off valve and fittings appropriate for hot
water supply line (copper tubing/compression
fitting, or braided hose).
UL listed conduit connector or strain relief
is required if you attach the field wiring
directly to the terminal block.
Four screws to mount the junction box
Hammer Hole Saw
Pliers Needle Nose Pliers Work Gloves Screwdrivers
Safety Glasses Adjustable Wrench
Measure Tape
Wire Strippers
LevelDrill
A Toe Panel Screws (Black)
B Mounting Bracket screws
C Screw Clamp for hose (in a separate bag with Junction Box)
D Rubber Drain Hose Adaptor
E Mounting Brackets
F Water Supply Adaptor fitting
G Flexible Edge Protector far Electrical Wire
H Junction Box
4
AvoidScaldingorElectricalShockHazard[
Makesure the water supply and electrical supply are
shut off before installation or service.
NOTE: This dishwasher is designed to be enclosed on
the top and both sides by standard residential kitchen
cabinetry.
Select a location as dose to the sink as passible far easy
access to water supply and drain lines.
Far proper dishwasher operation and appearance, ensure
that the enclosure is square and has the dimensions shown
below.
i
After locating the proper place for your new dishwasher,
you will need to make any required openings to allow far
passage of the water, drain and electrical line. In order
to avoid interference with the dishwasher when sliding it
into the cabinet, place your openings within the dimensions
shown below.
4-1/2'!
_(!!4rnrn) f
REQUIRED OPENINGS:
! 2-1/2"
[(64mm)
If the dishwasher is to be installed in a corner, make sure
that there is adequate clearance to open the door.
between / Countertop
dishwasher door
Check,¸
and wa
41/4 '' X 2" (10.8 X 5.2cm) - To pass the included electrical
supply [unction box through to
an adjacent cabinet
4"x2"(10x5cm)- To pass the included water
supply line toward the water
supply
11/4_ (3.2cm) diameter - To pass the dishwasher drain hose
toward the drain connection
NOTE: if the incoming electric supply, water supply and
drain connections are all in the same cabinet, the one
41/4" x 2" (1 0.8 x 5.2cm) hole will be large enough far all
three to pass through.
Before sliding the dishwasher into the cabinet, remove the
hose clip at the back of the dishwasher as shown below
and discard.
Avoid Electrical Shock/Fire Hazard
Do not allow the electrical and water supply lines to
touch.
................... i ........................... i............
5
Avoid Electrical Shock Hazard
Do not work on an energized circuit. Doing so could resul
in serious injury or death. Only qualified electricians
should perform electrical work. Do not attempt any work
an the dishwasher electric supply circuit until you are
certain the circuit is de-energized.
Electrical Supply
The customer has the respansibility of ensuring that the
dishwasher electrical installation is in compliance with all
national and local electrical codes and ordinances. The
dishwasher is designed for an electrical supply of 120V,
60 Hz, AC, connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker rated for
15 amps. Electrical supply conductors shall be a minimum
#14 AWG copper wire rated at 75°C (167°F) or higher.
Grounding Instructions
The dishwasher must be properly grounded before
operating. This appliance must be connected to a grounded
metal permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment grounding terminal or lead an
the dishwasher. Make sure that the dishwasher is connected
to a suitable ground in compliance with all local codes
or, in the absence of a local code, with the NATIONAL
ELECTRICAL CODE in the United States or the CANADIAN
ELECTRIC CODE C22.1 -latest edition in Canada as well as
any provincial/state or municipal or local codes that apply.
Dishwasher Bectrlccfl Rating
Volts Hertz Amperes Watts
Use the four screws (not supplied) to securely mount the
iunction box so that it can be easily accessed. The electrical
supply can be connected in two ways:
Method A - Three prong plug and receptacle
Use the included three-prong plug and iunction box to
connect to a dedicated household receptacle. Make sure
the household receptacle meets the electrical supply
requirements as well as national and local codes.
Method B - To permanently connect to household or field
wiring:
3eptacle or
!ld Wiring _
_lectric cord with "_
junction box and
three prong plug
are included
\with dishwashe[_
1. Remove the dishwasher electrical supply iunction box
cover and connect to the power supply cord from the
house installation.
2. Remove 2" to 3" (5.1 - 7.6cm) of the outer casing of
the household or field supply wiring as shown below.
Remove 3/8" to 1/2" (1 - 1.3cm) of the insulation from
each wire.
\
120 60 ] 2 1,450
(max)
Electrical Connection
The dishwasher electrical supply iunction box and
dedicated receptacle must be mounted in an accessible
cabinet adjacent to the dishwasher (do not mount the
iuncfian box or receptacle behind the dishwasher). You
will need a 41/4 ,' x 2" (10.8 x 5.1cm) opening thraught
the cabinet in order to pass the iunction box through. If
the opening is made through wood, sand it smooth. If the
opening is made through metal, use the included protective
grommet or other approved method to protect wiring from
damage.
ualified electricians should perform electrical work.
2"-
5.1cm 7.6 cm I
I
3/8" - 1/2"
lcm - 1.3 cm
6
3. Insert the bare copper or green wire(ground) to the "G"
ground connection of the terminal block and securely
tighten the terminal block screw.
4. insert the white (neutral) wire to the "N" connection of
the terminal block and securely tighten the terminal
block screw.
5. Insert the black(hot) wire to the "L" connection of the
terminal block and securely tighten the terminal block
screw.
6. Check aJJ eJectrica! connections to make sure they are
secure and then attach the junction box cover with the 4
screws.
Hot Water Supply
The hot water heater should be set to deliver
approximately 120 ° F (49 ° C) water to the dishwasher.
Water that is too hot can cause some detergents to lose
effectiveness. Lower water temperatures wJJl increase run
times. The hot water supply pressure must be between
15 - 145 psi (1 - 10 bar).
IMPORTANT NOTES:
• if using a solder joint instead of a compression
fitting, be sure to make a!l solder connections before
connecting the water supply line to the dishwasher.
• Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
• Always use the appropriate seal when making
plumbing connections.
• Before connecting the water supply line to the
dishwasher, flush the incoming water line for
approximately 5 minutes to clear any foreign material.
• Turn on the water supply and check for leaks after
connections are made.
METHOD A & B
As a final step, connect the dishwasher power supply plug
(connected to the junction box at the other end) in the slot
at the bottom of the dishwasher as shown below.
Dishwasher power supply plug
Temperatures required for soldering and sweating will
damage the dishwasher. Jf plumbing lines are to be
soldered or sweated, keep the heat
source at least 6 inches (152.4 ram) away from
the dishwasher.
Connecting the Hot Water SuppJy
There are two plastic corrugated hoses that exit the back
of the dishwasher. The larger hose, with the brass fitting
on the end, is the water supply hose to the dishwasher (the
other hose is the dishwasher drain hose). You will need a
3" x 13/4" (7.6 x 4.5cm) opening through the cabinet to
pass the dishwasher water supply line through toward the
shut off valve.
Toconnect the hot water supply:
1. Assemble the water supply adaptor fitting from the
parts bag onto the dishwasher water supply hose. This
connection does nat require Teflon brand tape.
2. Pass the dishwasher water supply line with attached
adaptor through the opening toward the water shut off
valve. Take care not to allow the hose to kink or twist
behind the dishwasher.
3. Connect the dishwasher water supply line with adaptor
to the water shut off valve. You will need to use an
approved dishwasher water supply line with the correct
fittings for this connection. Always use the appropriate
seal when making plumbing connections.
NOTE: The end of the dishwasher water inlet hose is
heavy and will need to be supported. It is best to lay
the end an the cabinet floor.
4. After all connections are made, turn on the hot water
and check far leaks.
IMPORTANT NOTES:
If local ordinance require an air gap, install it according
to the manufacturer's instructions.
If the dishwasher drain hose is to be connected to a
disposer dishwasher drain connection, remove the plug
from the disposer's dishwasher drain connection.
The dishwasher drain hose must have one place along its
length that is securely attached 20 inches (50.8cm) above
the cabinet floor.
The drain hose length can be extended if necessary. The
maximum length of the drain hose, including the hose
leading to the air gap, is 150 inches (381 cm).
The dishwasher drain hose may be connected to the
household or field drain plumbing in one of four ways. You
will need a 11/,, (3.2 cm) diameter hole in order to pass
the drain hose through the cabinet.
_4
Avoid Scald Hazard
Do not perform any work on a charged hot water line.
Serious injury could result. Only qualified plumbers should
perform plumbing work. Do not attempt any work on
the dishwasher hot water supply plumbing until you are
certain the hot water supply is shut off.
Non-Metallic Tie
\
_ MIN.
2o"
151cm
......J ....
Directly to the undersink Directly to a disposer
dishwasher drain connection, dishwasher drain connection.
To the undersink dishwasher
drain connection through an
air gap.
8
To a disposer dishwasher
drain connection through an
air gap.
For a large port, use the drain hose as it is.
Far a small port, insert the rubber drain hose adaptor into
the drain hose end as shown below.
1. Obtain the Rubber Drain Hose Adaptor screw clamp
from the Dishwasher Installation Kit (do not substitute).
2. Insert the dishwasher drain hose into the end of the drain
hose. Be sure to fully insert the drain hose.
3. Use the clamp provided to attach the Rubber Drain
Hose Adaptor to the house plumbing. Tighten until hose
can no longer rotate.
Before installing the supplied countertap mounting brackets,
decide which method of securing the dishwasher into its
enclosure will be used. Once the mounting brackets are
installed an the dishwasher, removing them is difficult and
will damage the mounting brackets and the dishwasher.
The dishwasher can be secured into its enclosure in two ways:
1. Top Mount is used for countertops made of wood
or other materials that can easily drilled. Orient the
mounting brackets as shown below and position the
the mounting brackets over the slots on the dishwasher's
front corners. Push the mounting brackets down firmly to
insert the tabs into the slots.
Drain Hose
Rubber drain
hose adaptor
Top Mount
°
Side Mount is used far cauntertaps made of marble,
granite, or other very hard materials that cannot be
easily drilled. Bend the mounting brackets along the
small holes and in the same direction as the two small
tabs. Orient the mounting brackets as shown below, and
position the two small tabs on the mounting brackets
over the two slats on the dishwasher's front corners.
Push the mounting brackets down firmly to insert the
tabs into the slots.
Do not use the dishwasher until it is completely installed.
When opening the door an an uninstalled dishwasher,
carefully open the door while supporting the rear of the
unit. Failure to fallow this warning can result in serious
iniury.
Side Mounl
9
Theunitshould now be ready to slide into the cabinet
opening. To avoid scratching the floor, use floor protection
and caution when sliding the dishwasher into the cabinet.
Make sure that the hoses and cords do nat bunch up behind
the unit or kink as you slide the unit back. Make certain to
slide the unit into place before raising the leg levelers.
1. Drive the mounting screws through the holes in the
mounting brackets as shown for Top or Side Mount.
2. After the unit is installed in the enclosure, leveled and
secured, lock the two front leg levelers in place by
driving the enclosed leg leveler locking screws into each
screw slat located in front of the levelers.
3. Tighten screws until they are flush with the surface of the
slots.
02 P
mrn/0.1 "
For Top Mount - Wooden
NOTE: If the dishwasher is not level, it may not operate
properly and could cause leaks.
Check that the leveling legs are firmly against the floor.
• Place a level against the front panel.
• Check that the dishwasher is plumb. If needed, adiust
leg levelers until dishwasher is plumb.
• Open the door.
• Place the level inside against the top of the tub.
• Check that dishwasher is level from side to side. Adiust
the leg levelers as necessary.
Adiusting the leg levelers:
• To adiust the front feet (X), turn clockwise to raise or
counter-clockwise to lower.
• To adiust the back foot, turn the center screw (Y)
clockwise to raise or counter-clockwlse to lower.
c5
~12mm/0.s ''
For Side Mount - Stone Countertop
10
Loading...