Bosch NPD-5001-POE Installation Guide

1 2

Important Safety Information

– The unit should be connected to PoE networks only,

without routing to the outside plant.

– Only qualified personnel can install or remove the

unit.

– The unit DATA IN and DATA & POWER OUT ports

are shielded RJ45 data sockets. They cannot be used as Plain Old Telephone Service (POTS) telephone sockets. Only RJ45 data connectors can be connected to these sockets.

– The AC wall socket-outlet must be near the unit

and easily accessible. You can remove AC power from the unit by disconnecting the AC power cord from either the wall socket-outlet or the unit appliance coupler.

–The unit DATA IN and DATA & POWER OUT interfaces

are qualified as Safety Extra-Low Voltage (SELV) circuits according to IEC 60950-1. These interfaces can only be connected to SELV interfaces on other equipment.

– The unit should only be connected to the IP device

with which it was bought. Using the unit with other IP devices can cause damage to the IP device.

3 4

– Read the installation instructions before connect-

ing the unit to its power source.

– Follow basic electricity safety measures whenever

connecting the unit to its power source.

– A voltage mismatch can cause equipment damage

and may pose a fire hazard. If the voltage indicated on the label is different from the power outlet voltage, do not connect the unit to this power outlet.

– The unit can be used only in Restricted Access

Locations.

– Do not use a cross-over cable between the output

and the camera.

– Do not to cover unit or block the airflow to the PoE

with any foreign objects. Keep the unit away from excessive heat and humidity and free from vibration and dust.

– Ensure that the cable length from Ethernet

network source to the terminal does not exceed 100 meters (330 feet). The PoE is not a repeater and does not amplify the Ethernet data signal.

– No On/Off switch exists; simply plug the unit into

an AC power source.

AC Power Cord Set: – The power cord must have regulatory agency

approval for the specific country in which it is used (for example UL, CSA, VDE, etc.).

– The power cord must be a three-conductor type

(two current carrying conductors; one ground conductor) terminated on one end by an IEC 60320 appliance coupler (for connection to the unit), and on the other end by a plug containing a ground (earth) contact.

– The power cord must be rated for a minimum of

250 VAC RMS operation, with a minimum rated current capacity of 5 amps (or a minimum wire gauge of 18 AWG (0.75 mm

– A unit installed in Australia requires power cords

with a minimum wire gauge of 16 AWG (1.0 mm2).

Connections

– Connect the unit to an AC outlet (100 – 240 VAC)

using the supplied power cord.

– Connect the DATA IN (input) to the remote

Ether-net network.

– Connect the DATA & POWER OUT (output) to the

camera (do not use a cross-over cable between the output and the camera).

Indicator

Cat. 5e/6

cables

Yellow Green Flashing green

camera

network

power is on camera is connected overload or short circuit

from

Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products. Please dispose of these units at an environmentally compatible recycling facility, per European Directive 2012/19/EU.

EMC Compliance – FCC Part 15 class B and EN55022 class B – EN55024 – VCCI

Safety Compliance – UL/cUL per 60950-1 – GS mark

NPD-5001-POE Midspan PoE Injector

Quick Installation Guide

More information

For more information please contact the nearest Bosch Security Systems location or visit:

http://www.boschsecurity.com/catalog_overview.htm

Bosch Security Systems B.V.

Torenallee 49 5617 BA Eindhoven The Netherlands

www.boschsecurity.com

AM18-Q0696 | 2015-09 | v1.0