Bosch NKT 92 User Manual

@ BOSCH

INSTALLATION INSTRUCTION MANUAL

for

Bosch Electric Built-in Ceramic Cook-top

Models NKT 72 and NKT 92

MANUEL D'INSTALLATION

Surface de cuisson _lectrique en €_r.amique encastr_e
ModUles NKT 72 et NKT 92

BEFORE YOU BEGIN, READ THESE INSTRUCTIONS "COM-
PLETELY AND CAREFULLY.

VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT DE
COMMENCER L'INSTALLATION.

r

IMPORTANT: Save these instructions for the local electrical inspector's use

INSTALLER: Please leave this manual with owner for future reference.

OW_R: Please keep this manual for future reference.

IMPORTANT: Conservez ce manuel pour l'inspecteur 61ectrique local.

INSTALLATEUR: Veuillez remettre ce manuel au propri_taire de l'appareil

pour r_f_rence.

PROPRIETAIRE: Veuillez garder ce manuel et vous en servir pour r6f6rence.

800 520 00 / 07.98

Table of Contents 3

Introduction

Tools You Will Need
power 'Requirements

Counter Preparation
Steps for Installation

Technical Data
Preparing the Location

for 30" Cook-Top
for 36" Cook-Top

Attaching Fastening Rails
Placing the Cook-Top
Electrical Supply

Electrical Connections
Final Check List

Schematic Wiring Diagrams

5
6
7

8
9

10

11
12

Table des mati_res

Introduction

Les outils dont vous aurez besoin
Sp6cifications _lectriques requises

Preparation du comptoir
I_tapes de l'installation

Donn_es techniques
Pr6paration de l'emplacement, 30"

Pr6paration de l'emplacement, 36"

Installation des rails de fixation
Mise en place de la surface de cuisson

Alimentation en _lectricit6
Connexions _lectriques

Liste de v4rification finale

Sch4ma 61ectrique

14

15
16
17

18
19

20

21
22
23

2

Introduction

Please read these instructions COMPLETELY
AND CAREFULLY. They will save you time and

effort and help to ensure optimum cook-top
performance. Be sure to observe all WARNINGS.

These installation instructions are intended for use
by a qualified installer. In addition to these
instructions the cook-top shall be incralled:

• In the United States, in accordance with the

National Electric Code/State and Municipal codes
and/or local codes.

• In Canada, in accordance with Canadian Electric

Code C22.1-1atest edition/Provincial and Municipal

codes and/or local codes.

These shall be carefully followed at all times.

TOOLS YOU WILL NEED
The following tools are needed to install your new

cook-top:

Tape measure and straightedge or ruler
Pencil

Phillips screwdriver
Pliers

Wire cutters and wire stripper

1" hole saw

Hand or saber saw

POWER REQUIREMENTS

The cook-top must be supplied with the proper
voltage and frequency. The cook-top must be

connected to a three wire or four wire, single phase,
240 or 208 volt, 60 Hz AC only electrical supply

on a separate circuit fused on both side of the line.
A circuit breaker or time-delay fuse sized not to

exceed the circuit rating of the appliance specified

• on the serial/rating plate located on the bottom of
the cook-top is recommended.

The cook-top must be connected with copper wires
ONLY.

COUNTER PREPARATION
Counter space must be provided for installation of

your new cook-top. When choosing a location
consider the following IMPORTANT

CONSIDERATIONS:

• Cabinet storage space located above the

cook-top should be avoided, to eliminate the
risk of burns or fire caused by reaching over

heated surface units of the cook-top. If you
choose to install cabinet storage above the

cook-top, install a range hood that extends
out horizontally at least 5" (127 mm)
beyond the bottom front edge of the

cabinets.

• If you choose to install cabinet storage above

• the cook-top, do not store any item(s) that

could be of interest to children in the

• cabinets above the cook-top. Children •
climbing on the cook-top could be seriously

burned.

• Ifyou choose to install cabinet storage above
the cook-top, ctonot store heavy, hard

objects that if dropped could damage the
ceramic cooking surface in the cabinets
above the cook-top.

STEPS FOR INSTALLATION
The following pages provide a step by step guide

for installation of the cook-top arranged as
follows:

Technical Data

Preparing the Location, for 30" cook-top
Preparing the Location, for 36" cook-top

Attaching F_tening Rails
Placing the Cook-Top in its Location

Electrical Supply
Electrical Connections

Final Check List

It is recommended that you have the electrical
wiring and hook-up of your cook-top performed by
a qualified electrician. After installation is complete
have the electrician show you where the main

disconnect is and which of the circuit breakers/fuses
are for the cook-top.

Technical Data

NKT 72 series, (30", 4 element)

Dimensions, NK'F 72

a Height 4" 102 mm
b Width 30" 762 mm

c Depth 20U2" 521 mm

Electrical Rating, NKT 72

Volts Hertz Amperes Watts

240 60 40 7 900
208 60 28 6 000

a •

NKT 92 series, (36", 5 element)

Dimensions, NKT 92

a Height 4" 102 mm

b Width 36" 914 mm
c Depth 201/_'' .. 521 mm

Electrical Rating, NKT 92

Volts

240
208

Hertz

60
60

A_l_res Watts

_ 9 900

74O0

a