Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
Notice!
Indicates a situation which, if not avoided, could result in
damage to the equipment or environment, or data loss.
Safety precautions
Caution!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code
(NEC 800 CEC Section 60) or applicable local codes.
Bosch Security Systems2016.08 | v1.0 | AM18-Q0707
6en | Safety
panoramic 6000/7000 IC
FLEXIDOME IP
1.3
Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Follow all warnings before operating the
device.
1.Clean only with a dry cloth. Do not use liquid cleaners or
aerosol cleaners.
2.Do not install device near any heat sources such as
radiators, heaters, stoves, or other equipment (including
amplifiers) that produce heat.
3.Never spill liquid of any kind on the device.
4.Take precautions to protect the device from power and
lightning surges.
5.Adjust only those controls specified in the operating
instructions.
6.Operate the device only from the type of power source
indicated on the label.
7.Unless qualified, do not attempt to service a damaged
device yourself. Refer all servicing to qualified service
personnel.
8.Install in accordance with the manufacturer's instructions in
accordance with applicable local codes.
9.Use only attachments/accessories specified by the
manufacturer.
10. Protect all connection cables from possible damage,
particularly at connection points.
2016.08 | v1.0 | AM18-Q0707Bosch Security Systems
FLEXIDOME IP
panoramic 6000/7000 IC
Safety | en7
1.4
FCC and ICES compliance
FCC & ICES Information
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCCRules. These limits are designed to provide reasonable
protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
–reorient or relocate the receiving antenna;
–increase the separation between the equipment and
receiver;
–connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
–consult the dealer or an experienced radio/TV technician
for help.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the
dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office, Washington,
DC 20402, Stock No. 004-000-00345-4.
Bosch Security Systems2016.08 | v1.0 | AM18-Q0707
8en | Safety
panoramic 6000/7000 IC
FLEXIDOME IP
1.5
Notices
Notice!
Optical elements are sensitive and should be protected at all
times. Do not allow objects to come into contact with glass
surfaces and do not touch optical elements with your fingers.
Notice!
Video loss is inherent to digital video recording; therefore,
Bosch Security Systems cannot be held liable for any damage
that results from missing video information.
To minimize the risk of losing information, we recommend
multiple, redundant recording systems, and a procedure to
back up all analog and digital information.
Notice!
We recommend that memory cards only be used for local
storage of alarm recordings.
2016.08 | v1.0 | AM18-Q0707Bosch Security Systems
FLEXIDOME IP
panoramic 6000/7000 IC
Short information | en9
2
Short information
This manual has been compiled with great care and the
information it contains has been thoroughly verified. The text
was correct at the time of printing, however, the content can
change without notice. Bosch Security Systems accepts no
liability for damage resulting directly or indirectly from faults,
incompleteness or discrepancies between this manual and the
product described.
Trademarks
All hardware and software product names used in this document
are likely to be registered trademarks and must be treated
accordingly.
More information
For more information please contact the nearest Bosch Security
Systems location or visit www.boschsecurity.com
http://www.boschsecurity.com/catalog_overview.htm
Bosch Security Systems2016.08 | v1.0 | AM18-Q0707
10en | System overview
panoramic 6000/7000 IC
FLEXIDOME IP
3
3.1
System overview
This discreet, aesthetic camera mounts flush in a ceiling or wall.
Its easily-painted cover plate blends in with almost all
surroundings. The 12MP sensor operating at 30 fps provides full
panoramic surveillance with complete area coverage, fine details
and high speeds. The camera offers full situational awareness
and simultaneous E-PTZ views in high resolution.
The 360° version of the camera, when mounted centrally on a
ceiling, gives complete wall‑to‑wall coverage. The 180° version
has a higher effective resolution and is ideal for wall mounting
or for ceiling mounting in corridors.
Application variants
The camera has a choice of application variants that set up the
camera for optimum performance in a specific environment.
Select the application variant best suited to your installation.
The application variant must be selected before any other
changes are made, as the camera reboots automatically and
resets the factory defaults when the application variant is
changed.
This camera has the following application variants:
–Client-side dewarping
–Edge dewarping
3.2
2016.08 | v1.0 | AM18-Q0707Bosch Security Systems
Using the camera
To access the features of the camera, use a web browser. The
browser provides live viewing of the camera streams in the
interface window, and also allows you to access and change the
extensive list of settings and parameters for camera
configuration. Refer to the software manual for more
information on the browser interface.
FLEXIDOME IP
panoramic 6000/7000 IC
The camera recording and storage functions include local alarm
recording and recording to iSCSI-based systems. The camera
can also use the Bosch Video Recording Manager (VRM) to
control recording and storage. Integration with the many Bosch
recording solutions is seamless.
System overview | en11
3.3
Operation with external systems
The web browser is the most direct way of using the camera,
however, the Bosch download store provides several other free
applications (listed below) for viewing and controlling the
camera.
Download store
Download the latest applications and firmware from:
http://downloadstore.boschsecurity.com/
Video Security Client
The Video Security Client is a free, easy-to-use video-surveillance
application provided by Bosch for local and remote monitoring
of IP cameras and appliances. The software supports up to 16
cameras.
The Video Security Client has extensive dewarping capabilities
and can be used for client-side dewarping as well as for viewing
the available modes.
Bosch Security Systems2016.08 | v1.0 | AM18-Q0707
12en | System overview
Bosch Video Client
The Bosch Video Client is a free Windows application to view,
operate, control, and administer surveillance cameras and
installations at remote locations. It offers a user-friendly
interface for easy live viewing of multiple cameras, playback,
forensic search and export.
IP Helper
The IP Helper tool is a free PC application that makes it easy to
detect Bosch cameras and devices on your network.
panoramic 6000/7000 IC
FLEXIDOME IP
3.3.1
Larger surveillance systems
Bosch Video Management System
The Bosch Video Management System is a unique enterprise IP
video surveillance solution that provides seamless management
of digital video, audio and data across any IP network. It is
designed to work with Bosch security products as part of a total
video surveillance management system.
Third-party integration
Third-party integrators can easily access the internal feature set
of the camera for integration into large projects. Access to
metadata is available to integrators via RTSP.
When connected to external systems, many of the camera
configuration parameters are controlled by the system and not
by the settings made via a web browser.
2016.08 | v1.0 | AM18-Q0707Bosch Security Systems
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.