Bosch NEZ-4112-PPCW4 User Manual

AUTODOME IP 4000 HD
NEZ-4xxx-xxxxx
en Installation Manual
AUTODOME IP 4000 HD Table of Contents | en 3

Table of contents

1
1.4 Important Safety Instructions 5
1.5 Connection in Applications 6
1.6 Important Notices 6
1.7 Customer Support and Service 10
2
3
4
5
5.1 Prepare Wiring 14
6
6.1 Description 15
6.2 Additional Tools Required 15
6.3 Preparing the Surface Mount for an Indoor Installation 15
6.4 Installing the Camera to the Mounting Plate 16
7
7.1 Parts List 21
7.2 Installation Requirements 21
7.3 Installing the Wall Mount 22
8
8.1 Parts List 24
8.2 Installing the Pipe Mount 25
9
10
11
12
12.1 Transfer 34
12.2 Disposal 34
13
Safety 4
Unpacking 11
Product Description 12
Mounting Accessories 13
Installation Overview 14
Installing a Surface Mount 15
Install a Wall Mount and Camera 21
Install a Pipe Mount and Camera 24
Connection 28
Troubleshooting 30
Maintenance 32
Decommissioning 34
Technical data 35
Bosch Security Systems Installation Manual 2015.03 | 0.1 |
4 en | Safety AUTODOME IP 4000 HD
1
1.1
1.2

Safety

About this Manual

This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing. Because of the ongoing development of products, the content of the manual may change without notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness, or discrepancies between the manual and the product described.

Legal Information

Copyright
This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
2015.03 | 0.1 | Installation Manual Bosch Security Systems
!
!
!
!
AUTODOME IP 4000 HD Safety | en 5
1.3

Safety Precautions

In this manual, the following symbols and notations are used to draw attention to special situations:
Danger!
High risk: This symbol indicates an imminently hazardous situation such as “Dangerous
Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily
injury, or death.
Warning!
Medium risk: Indicates a potentially hazardous situation. If not avoided, this may result in
minor or moderate injury.
Caution!
Low risk: Indicates a potentially hazardous situation. If not avoided, this may result in
property damage or risk of damage to the unit.
Notice!
This symbol indicates information or a company policy that relates directly or indirectly to the
safety of personnel or protection of property.
1.4
Bosch Security Systems Installation Manual 2015.03 | 0.1 |

Important Safety Instructions

Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operation.
Caution!
Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the National
Electrical Code® (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),
and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any
damages or losses caused by incorrect or improper installation.
Warning!
Bosch’s version of High PoE:
If supplying power to the camera by HPoE or a midspan device, you must install additional
surge protection.
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at least 3 mm, into the electrical installation of the building. If it is needed to open the housing, use this all-pole switch as the main disconnect device for switching off the voltage to the unit. Attachments - Use only attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the user's warranty or authorization agreement. Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60). Fuse rating - For security protection of the device, the branch circuit protection must be secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC Section 60).
6 en | Safety AUTODOME IP 4000 HD
Heat sources - Do not install unit near any heat sources such as radiators, heaters, or other
equipment (including amplifiers) that produce heat. High PoE or PoE+ (802.3at) – Never supply power via the Ethernet connection (High PoE or PoE+) when power is already supplied via the power connector, unless implementing an Auxiliary Power application (described in the section Connection in Applications).
Lightning - Take precautions to protect the unit from lightning and power surges. Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive
force or shock may damage the unit. Object and liquid entry – Never push objects of any kind into the device through openings, as the objects may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill or pour liquid of any kind on or into the device. Do not place objects filled with liquids, such as vases or cups, on the device. Ventilation – Any openings in the device / enclosure are provided for ventilation to prevent overheating and to ensure reliable operation. Do not block or cover these openings. Do not place the device in an enclosure unless proper ventilation is provided, or the manufacturer’s instructions have been adhered to. Outdoor signals - The installation for outdoor signals, especially regarding clearance from power and lightning conductors and transient protection, must be in accordance with NEC725 and NEC800 (CEC Rule 16-224 and CEC Section 60). Power disconnect - Units have power supplied whenever the power cord is inserted into the power source, or when High Power-over-Ethernet (High PoE) power is provided over the Ethernet CAT 5E/6 cable. The power cord is the main power disconnect device for switching off the voltage for all units. When High PoE or PoE+ (820.3at) is used to power the unit, the power is provided over the Ethernet cable, which is then the main power disconnect device for switching off the voltage for all units. Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights. Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of losing information, we recommend multiple, redundant recording systems, and a procedure to back up all analog and digital information. Servicing - Do not attempt to service this device yourself. Refer all servicing to qualified service personnel.
1.5
1.6
2015.03 | 0.1 | Installation Manual Bosch Security Systems

Connection in Applications

24 VAC power source: This unit is intended to operate with a limited power source. The unit
is intended to operate at 24 VAC (if PoE+ is not available). User supplied wiring must be in compliance with electrical codes (Class 2 power levels). PoE: Use only approved PoE+ devices. Power-over-Ethernet can be connected at the same time as a 24 VAC power supply. If auxiliary power (24 VAC) and PoE+ are applied simultaneously, the camera selects auxiliary input and shuts off PoE+. For in-ceiling or indoor pendant applications that don’t require heater power, standard PoE+ (802.3at) midspans or switches can be used to power the camera.

Important Notices

Indoor use only - The product shall only be used indoors. Ethernet network should be
connected to a network environment, which must comply with the following conditions:
AUTODOME IP 4000 HD Safety | en 7
1.1 The function of the ITE being investigated to IEC 60950-1 is considered not likely to require connection to an Ethernet network with outside plant routing, including a campus environment.
1.2 The ITE is to be connected only to PoE networks without routing to the outside plant.
Notice!
This device is intended for use in public areas only.
U.S. federal law strictly prohibits surreptitious recording of oral communications.
UL Disclaimer
Underwriter Laboratories Inc. ("UL") has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested fire, shock and/or casualty hazards as outlined in Standard(s) for Safety for Information Technology Equipment, UL 60950-1 . UL Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.
Notice!
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Bosch Security Systems Installation Manual 2015.03 | 0.1 |
en | Safety AUTODOME IP 4000 HD
8
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna; – Increase the separation between the equipment and the receiver; – Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected; – Consult the dealer or an experienced radio/TV technician for help. Intentional or unintentional modifications, not expressly approved by the party responsible for compliance, shall not be made. Any such modifications could void the user's authority to operate the equipment. If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
2015.03 | 0.1 | Installation Manual Bosch Security Systems
AUTODOME IP 4000 HD Safety | en 9
Bosch Security Systems Installation Manual 2015.03 | 0.1 |
10 en | Safety AUTODOME IP 4000 HD
1.7

Customer Support and Service

If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions.
Service Centers USA
Telephone: 800-366-2283 or 585-340-4162 Fax: 800-366-1329 Email: cctv.repair@us.bosch.com
Customer Service
Telephone: 888-289-0096 Fax: 585-223-9180 Email: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450 Fax: 585-223-3508 or 717-735-6560 Email: technical.support@us.bosch.com
Repair Center
Telephone: 585-421-4220 Fax: 585-223-9180 or 717-735-6561 Email: security.repair@us.bosch.com
Canada
Telephone: 514-738-2434 Fax: 514-738-8480
Europe, Middle East & Africa Region
Please contact your local distributor or Bosch sales office. Use this link:
http://www.boschsecurity.com/startpage/html/europe.htm
Asia Pacific Region
Please contact your local distributor or Bosch sales office. Use this link:
http://www.boschsecurity.com/startpage/html/asia_pacific.htm
More Information
For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com
2015.03 | 0.1 | Installation Manual Bosch Security Systems
AUTODOME IP 4000 HD Unpacking | en 11
2
2.1

Unpacking

This equipment should be unpacked and handled with care. Check the exterior of the
packaging for visible damage. If an item appears to have been damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in the Parts List below are included. If any items are
missing, notify your Bosch Security Systems Sales or Customer Service Representative.
Do not use this product if any component appears to be damaged. Please contact Bosch
Security Systems in the event of damaged goods.
The original packing carton is the safest container in which to transport the unit and must
be used if returning the unit for service. Save it for possible future use.

Parts List

1 AUTODOME IP 4000 HD camera
1 Camera mounting plate (pendant models only)
1 Mounting template (in-ceiling model only)
1 Screwdriver, T10 Torx
1 Screwdriver, T15 Torx
4 MAC address labels
1 Quick Installation Guide
Bosch Security Systems Installation Manual 2015.03 | 0.1 |
12 en | Product Description AUTODOME IP 4000 HD
3

Product Description

AUTODOME IP 4000 HD
The AUTODOME IP 4000 HD is a compact, indoor PTZ dome camera with a high-resolution 720p25/30 (1MP) or 1080p25/30 (2MP) HD sensor and a powerful 12x optical zoom that allows operators to monitor wide scenes without losing any details. The camera’s aesthetic design and flexible mounting options allow unobtrusive surveillance of large halls, reception areas, or waiting areas that would otherwise require multiple cameras for effective surveillance.
2015.03 | 0.1 | Installation Manual Bosch Security Systems
Loading...
+ 26 hidden pages