Bosch MAGIC.SENS MSS 400 Installation Details

Page 1

BDL - 4998121822
A4.en/ 23.08.2007
ST-FIR/ PRM1/ deh

INSTALLATION DETAILS MAGIC.SENS MSS 400

Fixing notes

The sounder base is designed for surface mounting and is provided for rear and surface cable
entry. The sounder insert has to be removed before fixing the mounting base. To release the
sounder insert, fixing clamps have to be pushed in direction of the arrows (Fig.2) . for rear
cable entry, conduit box mounting, feed the cable through the openings. For surface cable
feed, please break out the prepared cable entries. Install the mounting base with two screws
on a flat dry surface. Therefore, only the prepared fixing bores may be used (see Fig. 2)!

Technical Data

Dimensions : see Figure 1 and Figure 2
IP-Rating (as per EN 60529): IP30
Operating temperature: -10_C...+55_C
Storage temperature: -25_C...+85_C
Housing material: ABS plastics
Terminals: In and Out 0,28 - 2,5mm

2

Operating voltage: 9 - 15V DC / 15 - 28V DC
Current consumpt. from LSN (standby): 575 - 1025mA
Current consumption from LSN (alarm): 20mA

(depending on selected tone)
Bosch order number: 4.998.098.974
CPD number: 0786 - CPD - 20186

∅128

81,5

Sounder insert

Mounting b ase

Detector

Fixing springs

Figure 1: Di m ens i o ns Figure 2: I ns tal l ati o n de tai ls

Figure 3: Mo u nting order

Figure 4: Detector locking spring

Detector with sounder
base (complete fitted)

70

60
50

Cable entries for
under plaster cable feed

Use only these borings for
fixing the mounting base!

Sounder insert
fixing clamps

to

release

sounder

insert

Prepared cable
entries

Prepared cable
entries

Tone table

Page 2

BDL - 4998121822
A3.en/ 28.12.2004
ST-FIR/ PRM1/ deh

The sounder provides 11 different tones with additional second tone option (see table be­low). The sound intensity is selectable in 4 steps via the software WinPara. The tone selection
follows also via WinPara.

Both tones can be activated separately, whereby a subsequently activation of the second tone
switches off the first tone.

Ton

Tone type, Frequency, 2. Tone

Current

consum

p

-

Sound in-

tensity at

ToneTonetype,

Description

Frequency

,

Modulation

2.Ton

e

(not BZ 500)

consump

tion

[mA] at 24V

24V

[dB(A)]
±2dB

1

Sweeping,

DIN - tone

1200 - 500Hz

1Hz

970 Hz,

Continuous

max. 20 97

2

Sweeping (LF),

BS 5839, Teil 1, 1988

800 / 970Hz

1Hz

970 Hz,

Continuous

max. 20 96

3

Sweeping,

Australian tone, AS 2220

2400-2850Hz

7Hz

970 Hz,

Continuous

max. 20 92

4

Sweeping for 3,5s,

0,5s off, Dutch tone

500-1200Hz

3,5s On / 0,5s Off

970 Hz,

Continuous

max. 20 97

5

Continuous,

BS 5839, Part 1, 1988

970Hz

610 Hz,

Continuous

max. 20 97

6

Alternating tone,

French tone

554Hz / 100ms
440Hz / 400ms

970 Hz,

Continuous

max. 20 94

7

Continuous,

Schwedish tone

660Hz

970 Hz,

Continuous

max. 20 95

8

Alternating tone,

Low power

580Hz / 500ms

1000Hz / 500ms

610 Hz,

Continuous

max. 20 97

9

Pulsed tone,

Low power

580Hz

0,25s On / Off

610 Hz,

Continuous

max. 20 93

10

USA temporal 3 tone,

ISO 8201

610Hz

970 Hz,

Continuous

max. 20 95

11

USA temporal 3 tone,

ISO 8201

2850Hz

970 Hz,

Continuous

max. 20 96

Connection

Clamp Desc rip tion

+

interconne cte d

p

ower

-

interconnectedpower

supply

a1 / a2 LSN -

b1 , b2 LSN + (coming / going)

screen wire (has to be
isolated and as short as
possible)

b1 LSN+

b1 b2

b2 LSN+

a1 / a2 LSN-

Screen wire

+-

+ +

-

-