Page 1
LTC9316/00P
Security Systems
Installation Manual
Standard Pole
EN
Page 2
LTC9316/00P Instruction Manual Introduction
Table of Contents
1 DESCRIPTION
2 UNPACKING
3 SERVICE
4 4 INSTALLATION
4.1 Site Preparation
4.2. Installation
4.3 Mounting the AutoDome™
EN
2
2
2
2
3
3
3
4
1 DESCRIPTION
The LTC 9316/00P units are 16 foot steel mounting poles for
use with Unity® Domes, AutoDomes®, and the LTC 9320
Series of Outdoor Fixed Domes.
2 UNPACKING
Unpack carefully. This is mechanical equipment and should be
handled with care.
Check for the following:
• Packet Assembly for LTC 9316/00P:
1 Bosch Adapter Plate.
4 3/8 x 1-in Stainless Steel Hex Head Bolt.
4 5/16-18 Stainless Steel Hex Nut.
4 5/16 Stainless Steel Flat Wash.
4 3/8 Stainless Steel Split Lockwasher.
4 5/16 Stainless Steel Split Lockwasher.
1 Wiring grommet
1 Conduit plug
1 Installation Instructions (This Manual).
• Steel Pole
If an item appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper. If any items are
missing, notify your Bosch Security Systems Sales
Representative or
Customer Service.
The shipping carton is the safest container in which the unit
may be transported. Save it for possible future use.
3 SERVICE
If the unit ever needs repair service, the customer should
contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
Service Centers
U.S.A.: Phone: 800-366-2283 or 408-956-3895
fax: 800-366-1329 or 408-956-3896
e-mail: NationalServiceCenter@ca.slr.com
Canada: 514-738-2434
Europe, Middle East & Asia Pacifi c Regions:
32-1-440-0711
For additional information, see www.boschsecuritysystems.com
4 INSTALLATION
This installation should be made by qualifi ed service personnel and
conform to the National Electrical Code and applicable local codes.
Please read these instructions carefully before proceeding, and
heed all cautions.
!
4.1 Site Preparation
NOTE: Special attention must be paid to the size of the
!
wiring conduit and its location within the concrete
foundation and jig (if applicable). The Wiring
Conduit can be up to 2" in diameter. Use reducers
if necessary. Also, make sure that the Wiring
Conduit is in the center of the foundation and
Anchor Jig during installation (Figure 1).
Mounting
Bolts
Up to 2-inch
in Diameter
Figure 1 Mounting Bolts & Wiring Conduit Location
1. Select a suitable site for the LTC 9316/00P and prepare the pad site
using a hole 36" x 36" x 36" deep. The top of the concrete
foundation should be fl ush with the ground.
CAUTION: Be sure that there are no underground electric or
phone cables or gas or water lines in the area where the pole
!
will be located.
2. To help reinforce the concrete foundation, place (12) 1/2" diameter
x 32" long Reinforcement Bars (rebar) as shown in Figure 2. Use
suitable preparation methods to place the rebar.
Wiring
Conduit
Bosch Security Systems
10 October 2003
Page 3
LTC9316/00P Instruction Manual Installation
EN
3
36"
32"
24"
8"
6"
6"
24"
36"
24"
32"
24"
PV4 Anchor jig (if applicable)
8"
12"
4X 1.000O
BASED ON A 11.00" B.C.
13.000
3.000O
7.778
4.000
13.000
Figure 3 Anchor Bolt Dimensions
NOTE: Prepare the concrete per manufacturer's
directions. The concrete must have a compressive
!
strength of 3000 psi, and must be fabricated following
ACI318-89 requirements. Allow the concrete
foundation to cure thoroughly before proceeding with
the installation.
4.0007.778
11.000O
32"
36"
12"
Reinforcement bars (12)
Figure 2 Reinforcement Bars
3. FOR ANCHOR BOLT INSTALLATIONS:
Pour concrete per manufacturer's directions, making sure that
the wiring conduit is in the center of the pad. See Figure 3
(next page) for dimensions of the bolt pattern and suspend
appropriate bolts in the concrete around the wiring conduit.
Leave 2" to 3" of the Bolts protruding above the pad. If you are
using leveling nuts, leave 4" to 6" protruding.
Figure 4 View of Concrete Foundation
4.2 Installation
NOTE: Be sure that the pole is oriented properly, with the
!
carriage.
1. Place the pole on the pad with the holes on the Base Plate
aligned with the bolts of the anchor bolts or anchor jig
(Figure 5).
2. Remove the access opening plates at the bottom and top.
Bosch Security Systems
10 October 2003
Page 4
LTC9316/00P Instruction Manual Installation
Access opening plates
Bolts or
anchor jig
Figure 7 Lifting the Pole into Position
CAUTION: Pull all slack in the wiring as you lift the pole into
Pad
position to keep from pinching and possible damage.
EN
4
Figure 5 Placement of Pole on Pad
3. Insert the wiring into the 3" diameter hole in the base of the
pole. Be sure all slack is pulled completely through.
4. Insert connecting wiring into the bottom access opening, run
through the pole up to the top access opening. Insert the end
rough the housing connecting hole. Close the top access
opening and make necessary wiring connections at the bottom
access opening (Figure 6).
Top access opening
6. Ensure that the pole is vertical on all sides. Use a
bubble level or plumb bob to check.
7. Secure the pole to the pad with fasteners (Figure 8).
Nut
Lock Washer
Flat Washer
Figure 8 Securing the Pole to the Pad
4.3 Mounting the AutoDome
1. Align the holes of the AutoDome adapter plate with the
holes on the mounting plate at the top of the pole
(Figure 9).
®
Figure 6 Connecting Wiring Through Pole
5. Slowly lift the pole into the upright position, aligning
the holes of the Base Plate with the Bolts in the concrete
pad (FigurBosch Security Systems10 October 2003e 7).
Bosch Security Systems
10 October 2003
Page 5
Figure 9 Aligning Adapter Plate with Mounting Plate
2. Attach the LTC 9540/xx Wall Bracket adapter plate, using
the provided hex head nuts and bolts, flat washers, and
lockwashers (see Figure 10).
Figure 10 Attaching the Adapter Plate
3. Attach the LTC 9540/xx Wall Bracket to the adapter plate
using recommended 8 mm (5/16-inch) bolts/studs (refer to
the LTC 9540/xx Installation Instructions). Bolts should be
secured with nuts, washers, and lockwashers.
Figure 11 Mounting the LTC 9540/xx Wall Bracket
5 SPARE PARTS
Part No. Description
LTC9316AP LTC 9540/xx Wall Arm
Adapter Plate
Adapter Plate
Mount the LTC 9540/xx
Wall Bracket Using
These Holes
Lockwashers
Flat Washers
5/16-18 Nuts
Page 6
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 EE.UU.
Te l: 800-326-3270
Fax: 1-717-735-6560
www.boschsecuritysystems.com
Robert Bosch GmbH
Geschäftsbereich
Postfach 10 60 50
70049 Stuttgart
Te lefax (0711) 811-1234
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Te le +31 40 27 80000
© 2005 Bosch Security Systems GmbH
28 June
Data subject to change without notice.3935 890 38012
Loading...