Bosch HMV3061U/01, HMV3051U/01, HMV3021U/01 Installation Guide

Microwave oven

Model: HMV 3051 U

HMV 3061 U HMV 3021 U

BOSCH

Table of Contents

Safety ........................................ 4

Important Safety Instructions ...................................... 4

Before you begin ................................................. 7

Location requirements .............................................. 9

Installation procedure ............................................. 10

Removing the mounting plate ........................................ 10

Finding the wall studs ............................................... 10

Possible wall stud configurations ...................................... 10

Attaching the mounting plate to the wall ................................ 12

Installation types ................................................... 16

Roof venting ....................................................... 17

Wall venting ....................................................... 20

Room venting ..................................................... 25

Mounting the microwave oven ........................................ 27

Hood exhaust ..................................................... 29

Service .......................................................... 30

Safety

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Impo_ant

Examine your oven

Appliance handling safety

Intended Use

Grounding Instructions

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE. LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS

COMPLETE.

_ ARNING: Ifthe information inthis manual is not followed exactly, fire or

Unpack oven, remove all tape and packaging material and examine the oven for any damage such as dents, broken door latches or cracks in the door. Notify dealer

immediately if oven is damaged. Do not install if oven is damaged. Destroy the packaging after unpacking the appliance. Never allow children to play

with packaging material. Unit is heavy and requires at least two people or proper equipment to move.

Hidden surface may have sharp edges. Use caution when reaching behind or under appliance.

_ AUTION: For general ventilating use only. Do not use to exhausthazardous or explosive materials and vapours.

This appliance must be properly grounded. Grounding reduces risk of electric shock by providing an escape wire for the electric current if an electrical short occurs. This

oven is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

shock my result causing property damage or personal injury.

_ ARNING: Improper use of the grounding can result in a risk of electric

Consult a qualified electrician or servicer if grounding instructions are not completely understood, or if doubt exists as to whether the oven is properly grounded.

Do not use an extension cord. If the product power cord is too short, have a qualified electrician install a three-slot receptacle. This oven should be plugged into a separate 60 Hertz circuit with the electrical rating as shown in specifications table. When the oven is on a circuit with other equipment, an increase in cooking times may be required and fuses can be blown.

Microwave operates on standard household current, 110-120 V.

shock.

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Electrical Requirements ÷ a three prong grounded outlet

÷ 120 V, 60 Hz, AC only ÷ 15 Amp electrical supply with a fuse or a circiut breaker ÷ 1.6 kilowatt

This product must be connected to a supply circiut of the proper voltage and frequency. Wire size must conform to the requirements of the National Electric Code or the prevailing local code for this rating. The power supply cord and plug should be brought to a separate 15- to 20-amp branch circiut single grounded outlet. The

outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circiut should be installed by a qualified electrician and conform to

the National Electrical Code or the prevailing local code. The voltage used must be the same as specified on this microwave oven. Using a

higher voltage is dangerous and may result in a fire or oven damage. Using a lower voltage will cause slow cooking. The dealer is not responsible for any damages resulting from the use of the oven with any voltage other than specified.

Location requirements Check the opening where the microwave oven will be installed. The location must

provide: ÷ Minimum installation dimensions (See Installation Dimensions illustration) ÷ Minimum one 2" x 4" (50.8 x 101.6 mm) wood wall stud and minimum 3/8" (9.5

mm) thickness drywall or plaster/lath within cabinet opening.

÷ Support for weight of 150 Ibs (68 kg), which includes microwave oven and items

placed inside the microwave oven and upper cabinet.

÷ Grounded electrical outlet inside upper cabinet. (See Electrical Requirements)

section.

Notes:

If installing the microwave oven near a left sidewall, make sure there is at least 7" (178 mm) of clearance between the wall and the microwave oven, so that the door can open fully.

Some cabinet and building materials are not designed to withstand the heat produced by the microwave oven for cooking. Check with your builder or cabinet

supplier to make sure that the materials used will not discolor, delaminate or sustain other damages.

Ground continuity check The installer must perform a ground continuity check on the power outlet box before

beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or ifthe outlet box does not meet Electrical Requirements, a

qualified electrician should be employed to correct any deficiencies.

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Electric safety

Related equipment safety

_ AUTION: For personal safety, remove house fuse or switch off the circuitbreaker in the fuse box before beginning installation to avoid severe or fatal

shock injury. Lock circuit breaker to prevent power from being turned on

accidently. Be sure your appliance is properly installed and grounded by a qualified technician. Installer show the owner the location of the circuit breaker or fuse. Mark it for easy

reference. Do not, under any circumstances, cut or remove the ground prong.It must be

plugged into a matching grounding type receptacle to aviod electrical shock. Ifthere is any doubt as to wether the wall receptacle is properly grounded, the customer

should have it checked by a qualified electrician. Do not use an extension cord.

_ CAUTION: For personal safety, this product cannot be installed in cabinetarrangements such as an island or a peninsula. It must be mounted to both

a top cabinet and a wall.

_ WARNING: To reduce the risk of fire, use only metal ductwork.

Service and Repair Safety

_ ARNING: Do not repair or replace any part of the appliance unlessspecifically recommended in the manuals. Never modify or alter the

construction of the appliance. Improper installation, service or maintenance

can cause injury or property damage. Refer to this manual for guidance.

Refer all other servicing to a factory authorized service center.

Before you begin

Tools and parts needed

÷ No.1 Phillips screwdriver ÷ Pencil

÷ Ruler ortape measure and straight edge ÷ Drill with 3/16" (5 mm),l/2 '' (13 mm) and 5/8" (16 mm) drill bits ÷ Gloves

÷ Saw (saber, hole or keyhole) ÷ Stud finder or hammer

÷ Safety goggles ÷ Level

÷ Duct and masking tape

optional ÷ Carpenter square ÷ Tin snips (to cut damper)

÷ Scissors (to cut top cabinet template) ÷ Filler blocks or scrap wood pieces (for recessed bottom cabinet installations)

Parts included

B C D

You will find the installation hardware contained in packet with the unit. Check to make sure you have all these parts:

÷ A Self-Aligning Machine Screws 1A"-28x 31A'' (6-0,9 x 83 mm) ÷ B Toggle bolts 3/16" x 3" (5 x 76 mm)

÷ C Toggle wings ÷ D Wood screws _A"x 2" (6 x 51 mm)

÷ E Power chord strap ÷ F Nylon grommet (for metal cabinets) ÷ G Exhaust adaptor

Not shown: ÷ Top cabinet template

÷ Mounting plate (attached to the back of microwave oven) ÷ Aluminum grease filters

÷ Charcoal filter (attached to microwave oven)

Location requirements

Installation dimensions

Grounded outlet

(Inside cabinet above the oven)

12" (305mm) min.

127/8" (327mm) max.

161/2"

min.

Product dimensions

(349mm)

min.

153/4"

(400mm)

2" (51 mm)

30" (762mm)

min.

66" (1676mm)min.

161/2"

419mm)

297/8"

I 153/8"

(760mm) _(390mm)

Installation procedure

Removing the mounting

plate

Note: To avoid possible damage to the work surface or to the bottom of the appliance, cover the worksurface.

1. Remove any remaining contents from the microwave oven cavity.

2. Remove the screws from the mounting plate. This plate will be used as the rear wall template and for mounting.

3. Reinstall the screws into the holes where they were removed. Note: To avoid damage to the microwave oven, do not grip or use the door or door

handle while the microwave oven is being handled.

Finding the wall studs

Note: The microwave must be connected to at least one wall stud. If no wall studs exist within the cabinet opening, do not install the microwave oven.

1. Locate the edges of the wall studs within the cabinet opening by using: ÷ a stud finder or

÷ a hammer (tapping lightly across the mounting surface to find a solid sound).

2. Place a mark halfway between the edges and draw a line down the center of the

Possible wall stud configurations

These depictions show examples of preferred installation configurations with the mounting plate.

Note: Care must be taken when drilling holes. Electrical wires may be concealed behind the wall covering and contact with them could result in electrical shock.

studs (See possible wall studs configuration)

No wall studs at corner holes

Wall stud at one corner hole

Note: If wall stud is within 61A"(159 mm) of the vertical centerline, only Room Venting (recirculation) or Roof Venting installations can be done.

Wall studs at both corner holes

Attaching the mounting plate to the wall

Aligning the mounting plate

_ CAUTION: Wear gloves to avoid cutting fingers on sharp edges.

Note: Make sure the cabinet bottom is level.

1. Draw a vertical line on the wall at the center of the cabinet space.

2. Use the mounting plate as a template and place it on the wall, making sure that

the tabs are touching the bottom of the cabinet (Figure 1) or the level line

(Figure 2).

3. Line up the notch and centerline of the mounting plate to the centerline on the

wall.

4. While holding the mounting plate, draw circles on the wall at holes A, B, C

and D.

Note: If neither A, B, C nor D is in a stud, find a stud somewhere in the bottom area of the mounting plate and draw a fith circle to line up with the stud.

It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave.

-i

Figure 1 Flat or frame recessed bottom cabinet

_ m m _

_ m m y

m m y

Figure 2 Recessed bottom cabinet with front overhang

5. Set the mounting plate aside

6. Drill holes on the circles: ÷ 3/16" (5 mm) holes for wood screws (stud)

÷ 5/8" (16 mm) holes for toggle bolts (no stud)

Attaching the mounting plate (no wall studs at corner holes)

1. Insert the bolts into the mounting plate through the holes designated.

2. Attach toggle wings from the back of the mounting plate onto each bolt. Leave

enough space for toggle wings to go through the wall and to open.

3. Place the mounting plate against the wall and make sure tabs are touching the

bottom of the cabinet or the level line (see "Aligning the mounting plate").

4. Push the bolts through the drywall and finger tighten the bolts to make sure

toggle wings have opened against drywall.

Attaching the mounting plate (Wall stud at one corner hole)

,41

5. Check if the plate is properly centered, make sure it is level.

6. Securely tighten all screws, including the fifth wood screw in the bottom area of

the mounting plate.

1. Insert the bolts and the wood screws into the mounting plate through the holes

designated.

2. Attach toggle wings from the back of the mounting plate onto each bolt. Leave

enough space for toggle wings to go through the wall and to open.

3. Place the mounting plate against the wall and make sure tabs are touching the

bottom of the cabinet or the level line (see "Aligning the mounting plate").

4. Push the bolts through the drywall and finger tighten the bolts to make sure

toggle wings have opened against drywall.

5. Check if the plate is properly centered, make sure it is level.

6. Securely tighten all screws and bolts.

Attaching the mounting plate (Wall studs at both corner holes)

1. Insert the wood screws into the mounting plate through the holes designated.

2. Place the mounting plate against the wall and make sure tabs are touching the

bottom of the cabinet or the level line (see "Aligning the mounting plate").

3. Check if the plate is properly centered, make sure it is level.

4. Securely tighten all screws.

Installation types

ROOF VENTING

proceed to page 17

WALL VENTING

proceed to page 20

ROOM VENTING

proceed to page 25

Roof venting

Prepare upper cabinet 1. Remove power to outlet.

2. Remove all contents from upper cabinet.

3. Tape the TOP CABINET TEMPLATE onto the bottom surface. Make sure the

template centerline aligns with the vertical line on the wall. Rear wall arrows must

be against rear wall.

ooooooooooooloOOOOOOOOOOO

L ooooooooooo ooooooooooo

I i

I I I I I

Note: For recessed cabinet bottom, trim the template edges so that it fits inside the recessed area. The template has trim lines to use as guides.

i i

ooooooooooooloooooooooooo il(

ooooooooooo,i, ooooooooooo _

i ilc

4. Drill %" (9,5 mm) holes at "A", "B" and "C"

_ CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

5. Cut out the 2" (50,8 mm) hole at "D". This hole is for the power supply cord. Note: If the cabinet is metal, use the nylon grommet around the opening to protect

the cord.

6. Cut out the shaded area "E" using a saber or keyhole saw.

Adapting microwave blower 1. Remove and save the screws holding the blower motor and the blower plate. Lift

up the blower plate and put it aside.

2. Carefully pull out the blower unit and rotate 90° so that fan blade openings are

facing out the top of the microwave

3. Place the blower unit back into the opening.

_ AUTION: Do not pull or stretch the blower unit wiring. Make sure thewires are not pinched, and that they are properly secured.

4. Replace the blower plate and secure with the srews removed in step 1.

3. 4.

5. Attach the exhaust adapter to the top of the blower plate by sliding it into the

guides. Push in securely until it is in the locking tabs.

Make sure the damper hinge swings freely.

Proceed on page 27.

+ 41 hidden pages