Bosch GWS 6-115, GWS 7-115 Operating Instructions Manual
Atenção! Leia antes de usar.
¡Atención! Lea antes de usar.
Attention! Read before using.
GWS 6-115
GWS 7-115
Manual de instruções
Manual de instrucciones
Operating instructions
2
Figura ilustrativa
* Apenas para máquinas com eixo de trabalho com roscade 5/8"
*
*
Solamente para aparatos con husilo 5/8"
Only for tools with spindle thread 5/8"
13
Technical data
Machine components
1 Spindle lock
2 On/ Off switch
3 Auxiliary handle
4 Grinder spinde
5 Protective Guard (GWS 6-115)
5.1 Screw (GWS 6-115)
6 Protective Guard (GWS 7-115)
6.1 Clamping lever (GWS 7-115)
7 Mounting ange
8 Roughing/cutting disc**
9 Clamping nut
10 quick clamping nut**
11 Pinm sponner
12 Hand protector**
13 Rubber sanding plate**
14 Sanding disc**
15 Round nut*
16 Auxiliary handle with vibration absorption**
**Not all of the accessories ilustrated or described are included as standard delivery.
Intended use
The machine is intended for cutting, roughing and brushing
metal and stone materials without using water. For cutting
stone, a cutting guide is required.
Noise/vibration information
Measured values determined according to EN 50 144.
Typically the A-weighted noise levels of the product are: sound
pressure level: 88 dB (A); sound power level: 101 dB (A).
Wear hearing protection!
The typical weighted acceleration is 5.0 m/s2.
When using the auxiliary handle with vibration absorption,
the hand/arm vibration of the power tool used is typically
less than 2.5 m/s2.
For your safety
Working safely with this machine is possible only when
the operating and safety information are read completely
and the instructions contained therein are
strictly followed. In addition, the general
safety notes on page 17 must be observed.
Before using for the rst time, ask for a practical demonstration.
• Wear protective glasses and hearing protection.
• Wear protective gloves and sturdy shoes.
• When necessary, also wear an apron.
• The dust that is produced while working can be detrimental to health, inammable or explosive. Suitable safety measures are required.
Examples: Some dusts are regarded as carcinogenic. Use
suitable dust/ chip extraction and wear a dust respirator.
• Dust from light alloys can burn or explode. Always keep
the work place clean, as blends of materials are particularly dangerous.
• If the mains cable is damaged or cut through while working, do not touch the cable but immediately pull the mains
plug. Never use the machine with a damaged cable.
• Connect machines that are used in the open via a residual current device (RCD) with an actuating current of
30 mA maximum. Use only extension cables that are approved for outdoor use.
• When working with the machine, always hold it rmly with
both hands and provide for a secure stance.
• Always direct the cable to the rear away from the machine.
• Always switch the machine off and wait until it has come
to a standstill before placing it down.
• Insert the mains plug only when the machine is switched
off.
• For mains failure or when the main plug is pulled, unlock
the On/Off switch immediately and turn it to the off position. This prevents uncontrolled restarting.
• The machine must be used only for dry cutting/ grinding.
• For all work with the machine, the auxiliary handle 3 must
be mounted.
• Hold the power tool only by the insulated gripping sur-
faces, when performing an operation where the cutting tool may run into hidden wiring or its own cord.
Amoladora GWS 6-115 GWS 7-115
Order number 0 601 282 ... 0 601 800 ...
Power [W] 670 750
Amperage [A]
127 V 5,6 6,2
220 V 3,2 3,6
No-load speed [min –1] 11000 11000
Grinding disk ø máx. [mm] 115 (4 1/2”) 115 (4 1/2”)
Grinding spindle threads* M 14M 14
Weight approx. (without accessories) [kg] 1,4 1,7
Protection class
/ II / II
* For Central America countries spindle thread ∅ 5/8”
Loading...