Bosch Appliances diswacher User Manual

YOUR LIFE. OUR INSPIRATION.

Power

On/Off

Delay Start Hours

Top Rack Only

Cancel Drain

Power Scrub Plus

Scrub Wash

Regular Wash

Delicate/ Econo

Quick Wash

Rinse & Hold

Refill Rinse Agent

Cycle Countdown

Dishwasher Installation Instructions

Instructions d’installation du lave-vaisselle Instrucciones de instalación para lavavajillas

Use and Care Manual located on reverse side Tourner le guide pour les instructions d’utilisation et d’entretien Voltee el manual para encontrar las instrucciones de uso y cuidado

9000063358 (8503)

Table of Contents / Important Instructions

Table of Contents

IMPORTANT INSTRUCTIONS ................................ 1

Tools Needed ........................................................... 2

Materials Needed .....................................................2

Materials Supplied ...................................................3

Enclosure Preparation ............................................. 4

Electrical Preparation .............................................. 5

Plumbing Preparation ........................................... 6-7

Dishwasher Preparation ........................................ 7-8

Door Panel Installation .............................................9

Important Safety Instructions

WARNING

To avoid possible injury or property damage, OBSERVE ALL WARNINGS AND CAUTIONS. These instructions are intended for use by qualified installers only.

The dishwasher must be installed by a qualified service technician.

• In addition to these instructions, the dishwasher shall be installed to meet all electrical and plumbing codes and ordinances (both national and local).

Read these installation instructions completely and follow them carefully. They will save you time

and effort and help to ensure safety and optimum dishwasher performance.

If the dishwasher is installed in a location that experiences freezing temperatures (e.g., in a holiday home), you must drain all the water from the dishwasher’s interior. Water system ruptures that occur as a result of freezing are not covered by warranty.

Placing the Dishwasher ......................................... 10

Securing the Dishwasher ....................................... 10

Drain Hose Connection .......................................... 11

Hot Water Connection ............................................12

Electrical Connection........................................ 13-14

Door Tension Adjustment ....................................... 14

Base and Toe Panel .......................................... 14-15

Final Instructions ................................................... 15

Customer Service .................................................. 16

IMPORTANT

• The dishwasher drain hose must be installed with a portion of it at least 20” (508mm) off the cabinet floor; otherwise the dishwasher may not drain properly.

• This dishwasher is intended for residential use only, and should not be used in commercial food service establishments.

• NEW INSTALLATION - If the dishwasher is a new installation, most of the work must be done before the dishwasher is moved into place.

• REPLACEMENT - If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary.

Inspect the Dishwasher

After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately. Cosmetic defects must be reported within 5 days of installation. NOTE: Do not discard any bags or items that come with the original package until after the entire installation has been completed.

TOOLS NEEDED

Tools and Materials Needed

Hammer Hole Saw

Tape Measure

Wire Cutter

Slot Screwdriver

Wire Stripper

Phillips Screwdriver

Drill

MATERIALS NEEDED

(Additional materials may be required to comply with local codes.)

Pipe Wrench

Adjustable Wrench

Torx Screwdriver

Level

Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1 ground, insulated copper conductors rated 75°C or higher.

Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line.

Shut-off valve and fittings appropriate for hot water supply line (copper tubing/ compression fitting, or braided hose).

90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg.

Teflon tape or other pipe thread compound to seal plumbing connections.

UL listed conduit connector or strain relief.

Materials Supplied

MATERIALS SUPPLIED

Accessory Parts Supplied

Accessory parts for your dishwasher come in one or more plastic bags that are outlined below.

NOTE: Make sure you save all the bags until you have completed your installation.

Manual Set Bag

A Manual Set Bag is provided with each dishwasher and includes:

A Use & Care Instructions and Installation

Instructions (both manuals may be included in a single “flip-style” book

B Quick Reference Guide (select models) C Extra Tall Item Sprinkler D SHI and SHV Installation Template (SHI and SHV

models only)

E White Cotton Insulation Strip (SHY66C, SHX99A,

SHE66C, SHE99C, SHX57C and SHV57C models only)

Dishwasher Installation Kit

A Dishwasher Installation Kit is provided with each dishwasher and includes:

F Toe Panel Screws (2 black machine screws)

Note: These screws are included, but not used on models with the Toe Panel Installation Kit.

G Counter Top Mounting Brackets (2 “L” shaped metal

brackets)

H Mounting Bracket Screws (2 silver wood screws) I Rubber Drain Hose Adaptor (1 black rubber tube) J Hose Clamps ( 1 silver spring clamp to use to

attach the rubber adaptor to the Drain Hose and 1 gold screw clamp to attach the rubber adaptor to the plumbing)

K Wire Nuts (3 for electrical connection) L Electrical Junction Box Screws (2 silver

machine screws)

M Leg Leveler Locking Screws (2 gold coarse

threaded screws)

SHI/SHV Door Panel Installation Kit

A Door Panel Installation Kit is provided with select dishwashers that use a custom wood door panel and includes:

N Plastic Caps (2) O Spring Tension Screws (2 larger silver machine

screws used to adjust the door springs to accommodate doors of different weights)

P Door Mounting Brackets (2 gold metal brackets

and 2 white plastic brackets used to mount the custom door)

Q Door Mounting Bracket Screws (8 silver wood

screws)

R Door Mounting Screws (2 long silver screws used

to attach the door)

Toe Panel Installation Kit

A Toe Panel Installation Kit is provided on models SHY66C, SHX99A, SHE66C, SHE99C, SHX57C, and SHV57C. These models have a special noise reducing Toe Panel with the following mounting hardware:

S Toe Panel Screws (2 black screws used to attach

the metal Toe Panel)

T Black Plastic Base Access Panel Screws (2 long

silver screws used to attach the Black plastic Base Access Panel to the dishwasher.

S T

Enclosure Preparation

Check clearance between dishwasher door and wall

34" (864mm) minimum

23-5/8" – 24-1/4" (600–616 mm)

Figure 1

Countertop

23-9/16"

(598mm)

90 90

WARNING

Electrical Shock Hazard

To avoid electrical shock, make sure the water supply and electrical supply are shut off before installation or service.

ENCLOSURE PREPARATION

NOTE: This dishwasher is designed to be enclosed on the top and both sides by standard residential kitchen cabinetry.

Select a location as close to the sink as possible for easy access to water supply and drain lines. For proper dishwasher operation and appearance, ensure that the enclosure is square and has the dimensions shown in Figure 1. If the dishwasher is to be installed in a corner, make sure that there is adequate clearance to open the door. See Figure 2.

WARNING

Electrical Shock/Fire Hazard

To avoid electric shock or fire, do not allow the electrical and water supply lines to touch. Separate channels are provided under the dishwasher (see page 10).

Figure 2

3-1/2"

(89mm)

Figure 3

1-5/16"

(33mm)

If the enclosure requires openings for the electrical supply cable, hot water supply line, and dishwasher drain hose, place them within the dimensions shown by the shaded area of Figure 3 to avoid interference with the dishwasher frame or other components. Make the openings for the electrical supply cable and hot water supply line 1” (25.4mm) diameter. Make the opening for the dishwasher drain hose 1-1/4” (32mm) diameter. If the openings are made through wood, sand them smooth. If the openings are made through metal, make them large enough to accommodate grommets or other protective sheaths with inside diameters of 1” (25.4mm) for the electrical supply cable and the hot water supply line, and 1-1/4” (32mm) for the dishwasher drain hose.

(762mm)

3/8" - 1/2"

( 8mm - 13mm)

3" - 4"

( 75mm - 100mm)

21"

(533mm)

30"

Electrical Preparation

ELECTRICAL PREPARATION

WARNING

Electrical Shock Hazard

To avoid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.

Figure 4

Dishwasher Electrical Rating

stloVztreHserepmAsttaW

0210651

Figure 5

WARNING

Fire Hazard

To avoid a fire hazard, make sure electrical work is properly installed. Only qualified electricians should perform electrical work.

054,1

)xam(

Electrical Supply

The customer has the responsibility of ensuring that the dishwasher electrical installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amps. Electrical supply conductors shall be a minimum #14 AWG copper wire rated at 75°C or higher.

Regardless of where the electrical supply cable enters the enclosure (following the guidelines on page 8), position the cable 21” (533mm) from the enclosure’s left side, as shown in Figure 4. Extend the cable 30” (762mm) from the enclosure’s back, as shown in Figure 4.

Remove 3” - 4” (75mm - 100mm) of the cable’s outer casing, as shown in Figure 5, then remove 3/8” - 1/2” (9 - 13mm) of insulation from each wire, as shown in

Figure 5.

14"

(355mm)

Shut off

Valve

Hot Water

Supply

Line

Plumbing Preparation

PLUMBING PREPARATION

To avoid being scalded, do not perform any work on a charged hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off.

WARNING

Scald Hazard

Figure 6

Temperatures required for soldering and sweating will damage the dishwasher’s base and water inlet valve. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher’s base and water inlet valve.

Hot Water Supply

The hot water heater should be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 15 - 145 psi (1 - 10 bars).

Hot Water Supply Plumbing Install an easily accessible shut-off valve (not supplied) in the hot water supply line, as shown in Figure 6. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water may also be supplied to the dishwasher by using a braided hose line. Check with your local plumbing supply sources for the proper hose and 90° elbow fitting.

NOTE: Regardless of where the hot water supply line

enters the enclosure, position the line 14” (355mm) from the enclosure’s left side, as shown in Figure 6.

NOTE: Decide whether braided hose or copper tubing will be used for the hot water supply plumbing, and purchase the correct type of hot water supply shut-off valve, 90° elbow, and necessary fittings for the hot water supply plumbing.

PLUMBING PREPARATION (continued)

Drain Plumbing Under Sink Drain Connection

If the dishwasher is to drain either directly into the household drain plumbing or through an air gap, install a y-branch tailpiece under the sink as shown in Figure 7.

Installing an Air Gap

If local ordinances require an air gap, as shown in Figure 8, install it according to the manufacturer’s instructions.

Disposer

Make sure to remove the disposer’s dishwasher drain connection plug before connecting the dishwasher drain hose. See Figure 9.

DISHWASHER PREPARATION

Dishwasher preparation involves four tasks:

• Installing the Mounting Brackets

• Removing the Toe Panel

• Installing the 90° elbow fitting

• Junction Box Preparation

Installing the Countertop Mounting Brackets

25” (636 mm)

Door Panel Installation

1/4” max. (6 mm)

DOOR PANEL INSTALLATION

SHU/SHE Models - Accessory Panel Installation

If you have an SHU/SHE model and have ordered an accessory panel kit, install the panel prior to sliding the dishwasher into place. The panel dimensions are shown in Figure 15.

23-1/16” (586 mm)

Figure 15

SHI Models - Panel Installation

SHI models come with additional mounting hardware and a template sheet with installation instructions. The stainless steel models of the SHI series also come with two extension pieces. The extension pieces are used to match the control panel height (Figure 16, “B” dimension) to the horizontal drawer line of the cabinets, and must be installed as shown in on the template sheet. The standard piece is used for drawer heights up to 6” (152mm); the long piece is used for drawer heights greater than 6” (152mm) but 6-7/16” (164mm) or less. If your drawers are taller than 6-7/16”, you can either slide the extension piece in as far as it will go, or remove it and fit the door panel directly below the control panel.

SHI/SHV Models - Panel Installation

SHV models come with additional mounting hardware and a template sheet that will show you how to mount the panel. One side of the template shows how to mount a one piece panel; the other side shows how to mount a two piece panel. Decide which type of installation you want before proceeding with the installation.

Figure 16

Fig. 16

Dimension

SHI Only

Fig. 17

Dimension

D (SHI)

(SHI & SHV)

Extension “A”

Max. - Min.

Standard

5/16 - 11/16”

(8-18mm)

Long

11/16 - 1 1/8”

(18 - 29mm)

Panel Dimension

20 11/16” - 25”

(526mm - 635mm)

27 3/16” - 30 5/16” (690mm - 770mm)

23 3/16” - 23 3/8”

(589mm - 594mm)

“B” “C”

Max.-Min.

5 5/16”

(135mm)

5 5/8 - 6 7/16”

(143 - 164mm)

Figure 17

PLACING THE DISHWASHER

1 Straighten and position the hot water supply line and

the electrical supply cable as shown in Figure 18 so that they will align with their channels under the dishwasher base.

2 Position the dishwasher close enough to the enclosure

so that you can run the dishwasher drain hose to the under sink drain connection. Make certain that the hot water supply line and the electrical supply cable are in their channels under the dishwasher base, as shown in

Figure 19.

3 Slide the dishwsher into the opening making sure that

the hot water supply line and the electrical supply cable stay in their proper channels.

4 Make sure the dishwasher is level. Adjust the rear

leveler by turning the center screw at the front of the dishwasher, as shown in Figure 20a. Turning the screw clockwise raises the rear of the dishwasher. Adjust the front levelers by turning them with a screwdriver, as shown in Figure 20b. Turning the levelers to the right raises the dishwasher. If additional height is needed, shims may be added under the leveler feet.

SECURING THE DISHWASHER

1 Drive the mounting screws through the holes in the

mounting brackets as shown in Figure 21 for Top Mount or Side Mount.

2 After the unit is installed in the enclosure, leveled and

secured, lock the two front leg levelers in place by driving the enclosed leg leveler locking screws into each screw boss located in front of the levelers. See

Figure 22.

3 Tighten screws until they are flush with the surface of

the bosses.

Figure 21

Silver Spring Clamp

Gold Screw Clamp

Drain Hose Connection

Installation of the Rubber Drain Hose Adaptor

1 Obtain the Rubber Drain Hose Adaptor and the two

hose clamps from the Dishwasher Installation Kit.

2 On one outside end of the Rubber Drain Hose Adapter

is a raised groove. Insert the drain hose into the end without the raised groove. Be sure to fully insert the drain hose.

3 Secure the connection with the Silver Spring Clamp. 4 Use the Gold Screw Clamp to attach the Rubber Drain

Hose Adaptor to the house plumbing.

Connecting the Drain Hose to the Household Plumbing

The dishwasher drain hose may be connected to the drain plumbing in one of four ways: 1 Directly to the undersink dishwasher drain connection,

as shown in Figure 23.

2 Directly to a disposer dishwasher drain connection, as

shown in Figure 24.

3 To the undersink dishwasher drain connection through

an air gap, as shown in Figure 25.

4 To a disposer dishwasher drain connection through an

air gap, as shown on Figure 26.

Figure 23 Figure 24

Figure 25 Figure 26

Information on installing air gaps and disposers can be found in the Plumbing Preparation section of this manual.

NOTE: If the dishwasher drain hose is to be connected to a disposer dishwasher drain connection, remove the plug from the disposer’s dishwasher drain connection. Use the supplied Rubber Drain Hose Adaptor and Drain Hose Clamps to connect the dishwasher drain hose to the plumbing drain connection. Use the spring clamp to secure the Rubber Drain Hose Adaptor to the dishwasher drain hose. Use the screw clamp to secure the Rubber Drain Hose Adaptor to the plumbing drain connection.

The dishwasher drain hose must have one place along its length that is securely attached 20 inches above the cabinet floor.

Hot Water Connection

HOT WATER CONNECTION

NOTE: Make certain that the correct 90° elbow fitting (not

supplied) for the hot water supply line has been purchased and installed on the dishwasher as described in the Dishwasher Preparation section of this manual. The hot water supply line may be connected to the dishwasher in one of two ways:

1 With braided hose. 2 With copper tubing.

Braided Dishwasher Supply Hose

After connections are made turn on the hot water supply to check for leaks. NOTE: Braided dishwasher supply hoses can also be used to extend pre-existing dishwasher water supply lines.

WARNING

Scald Hazard

Copper Tubing

Temperatures required for soldering and sweating will damage the dishwasher’s water inlet valve. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher’s water inlet valve.

• If using a solder joint instead of a compression fitting, be sure to make all solder connections before connecting the water line to the dishwasher.

• Make certain there are no sharp bends or kinks in the water line that might restrict water flow.

• Be sure to use pipe thread compound or Teflon tape to seal the connection when required.

• Before connecting the copper hot water supply line to the dishwasher, flush it with hot water to clear any foreign material.

• Turn on the water supply to check for leaks after making connections.

NOTE: Do not use pipe sealant on compression fittings.

Electrical Connection

ELECTRICAL CONNECTION

Figure 27

Strain Relief Plate

Figure 28

Strain Relief Plate

Strain Relief (not supplied)

WARNING

Electrical Shock Hazard To avoid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.

WARNING

Fire Hazard

To avoid a fire hazard, make sure electrical work is properly installed. Only qualified electricians should perform electrical work.

Grounding Instructions

The dishwasher must be properly grounded before operating. This appliance must be connected to a grounded metal permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dishwasher. Make sure that the dishwasher is connected to a suitable ground in compliance with all local codes or, in the absence of a local code, with the NATIONAL ELECTRICAL CODE in the United States or the CANADIAN ELECTRIC CODE C22.1-latest edition in Canada as well as any provincial/ state or municipal or local codes that apply.

1 Retrieve the strain relief plate, and install a strain relief

(not supplied) into the opening on the strain relief plate.

NOTE: Orient the strain relief as shown in Figure 27.

2 Pass the electrical supply cable through the strain

relief, as shown in Figure 28. Leave 3 - 4 inches of insulated wire extending through the strain relief plate.

3 Tighten the strain relief screws. 4 Slide the strain relief plate into the junction box, and

secure it to the junction box with the supplied screw.

Electrical Connection/ Door Tension Adjustment/ Base and Toe Panel

ELECTRICAL CONNECTION (continued)

WARNING

Fire Hazard

To avoid a fire hazard, make sure there are no loose electrical connections. Make sure all

1/8” 3mm

Figure 29

electrical connections are properly made.

• Do not pre-twist the wires before connecting them with wire nuts.

• Extend the dishwasher’s stranded wires 1/8” (3mm) beyond the power supply cable’s solid wires, as shown in Figure 29.

5 Using the supplied wire nuts, connect the electrical

supply wires to the dishwasher’s wires, black to black, white to white, and green or bare. Make certain that the insulated wires show no bare wire from the bottoms of the wire nuts. Gently tug the wires to make certain they are securely connected.

6 Press the wires into the junction box. Make certain

that the wire nuts do not loosen.

7 Place the cover on the junction box and secure it to

the junction box with the supplied screw.

Figure 30

Figure 31

DOOR TENSION ADJUSTMENT (only on SHI and SHV models with custom door panels)

After the dishwasher and custom door panel are installed, open and close the door several times to make sure that it does so with ease. If the door closes too quickly, the spring tension needs to be adjusted.

To Adjust the Spring Tension: 1 Obtain the provided Spring Tension Screws from the

SHI/SHV Door Panel Installation Kit.

2 Insert the screws as shown in Figure 30. Turning the

screw clockwise increases the spring tension.

TOE PANEL INSTALLATION

Regular Toe Panel Installation

Use the toe panel screws from the Dishwasher Installation Kit and a Torx screwdriver to install the toe panel as shown in Figure 31.

+ 36 hidden pages