Bosch DIE 165 R User Manual

en Operating and

installation instructions

fr Mode d’emploi et

notice de montage

es Instrucciones deuso

y de montaje

DIE 165 R

Internet: http://www.bosch-hausgeraete.de
Bosch Info-Team: de Tel. [phone] (E 0,14/Min. DTAG)

2

en

page 03–16

fr

pages 17 – 30

es

página 31 – 44

Abb. 1

ELECTRO

Fig. 1
GAZ

3

Appliance description

Operating modes

Exhaust-air mode:

❑ The extractor-hood fan extracts the

kitchen vapours and conveys them
through the grease filter into the
atmosphere.

❑ The grease filter absorbs the solid

particles in the kitchen vapours.

❑ The kitchen is kept almost free of grease

and odours.

 WARNING

When the extractor hood is operated in
exhaust-air mode simultaneously with a
different burner which also makes use of
the same chimney (such as gas, oil or

coal-fired heaters, continuous-flow heaters,
hot-water boilers) care must be taken to

ensure that there is an adequate supply
of fresh air which will be needed by the

burner for combustion.
Safe operation is possible provided that the

underpressure in the room where the
burner is installed does not exceed 4 Pa
(0.04 mbar).

Instructions for use:

Operating modes

This can be achieved if the combustion air
is able to flow through non-lockable
openings, e.g. in doors, windows and in
conjunction with an air supply/air-intake wall
box or by other technical procedures such
as reciprocal interlocking.

If the air intake is inadequate, there is a
risk of poisoning from combustion gases
which are drawn back into the room.

An air-intake/exhaust-air wall box by itself is
no guarantee that the limiting value will not
be exceeded.

Note: When assessing the overall
requirement, the combined ventilation
system for the entire household must be
taken into consideration. This rule does not
apply to the use of cooking appliances,
such as hobs and ovens.

Lighting

Filter
grille

Chimney
panelling

Light / fan

switches

4

Gas hobs / Gas cookers

 Do not use all the gas hotplates

simultaneously for a prolonged period
(max. 15 minutes) at maximum thermal
load, otherwise there is a risk of burns if the
housing surfaces are touched or a risk of
damage to the extractor hood. If the
extractor hood is situated over a gas hob,
operate the hood at maximum setting if
three or more gas hotplates are operated
simultaneously.

Before using for the first time

Important notes:

❑ The Instructions for Use apply to several

versions of this appliance. Accordingly,
you may find descriptions of individual
features that do not apply to your
specific appliance.

❑ This extractor hood complies with all

relevant safety regulations.
Repairs should be carried out by

qualified technicians only.

 CAUTION

Improper repairs may put the user at
considerable risk.

❑ Before using your appliance for the first

time, please read these Instructions for
Use carefully. They contain important
information concerning your personal
safety as well as on use and care of the
appliance.

❑ Please retain the operating and

installation instructions for a subsequent
owner.

❑ This appliance is labelled

in accordance with
European Directive
2002/96/EG concerning
used electrical and
electronic appliances
(waste electrical and
electronic equipment –
WEEE). The guideline
determines the framework for the return
and recycling of used appliances as
applicable throughout the EU.

5

Before using for the first time

SAFETY INSTRUCTIONS

Do not flambé food directly under the
extractor hood.
Risk of grease filter catching fire due
to flames.

The hotplates must always be covered with
a utensil.

The extractor hood must not be
operated above a solid-fuel or gas fire (coal,
wood, etc.) (see installation instructions).

Do not operate all hotplates
simultaneously over a prolonged period
(max. 15 minutes) at maximum thermal
load, otherwise there is a risk of burns from
touching the housing surfaces or a risk of
damaging the extractor hood. When
operating the extractor hood above a hob,
operate the hood at maximum setting if
three or more hotplates are on at the same
time.

Do not use the appliance if damaged.
The appliance is not intended for use by

young children or infirmed persons
without supervision.
Young children should be supervised to
ensure they do not play with the appliance.

When children become old enough to use
the appliance, it is the legal responsibility of
the parents or legal guardian to ensure that
they are instructed in its safe use by quali­fied persons.

If the connecting cable for this
appliance is damaged, the cable must be
replaced by the manufacturer or his
customer service or a similarly qualified
person in order to prevent serious injury to
the user.

The appliance must be connected to the
mains by a qualified technician only.

Dispose of packaging materials
properly (see Installation instructions).

Safety instructions

This extractor hood is designed for
domestic use only.

Light bulbs must always be fitted when the
extractor hood is in use.

Defective bulbs should be replaced imme­diately to prevent the remaining bulbs from
overloading.

Never operate the extractor hood
without a grease filter.

Overheated fat or oil can easily catch fire.
If you are cooking with fat or oil, e.g. chips,
etc., never leave the cooker unattended.

Carefully clean the extractor hood
before switching on for the first time.

Do not place any objects on the
extractor hood.

6

Intensive setting:

Maximum power is obtained at the
intensive setting. It is only required for short
intervals.

❑ Keep pressing the + button until a

ç

appears in the display.

❑ If the intensive setting is not cancelled by

hand, the fan will automatically switch
back to step } after 10 minutes.

Lighting:

❑ The light can be switched on at any

time, even though the fan is switched off.

❑ Adjusting the brightness:

Hold down the 0 button until the desired
brightness is obtained.

Operating procedure

Acoustic signal:

❑ When a button is pressed, this is verified

by an acoustic signal.

Switching off the acoustic signal:

❑ Simultaneously press buttons 0 and+

until a signal is emitted after approx.
3 seconds.

Switching on the acoustic signal:

❑ Repeat the process.

Switching the fan ON
❑ Press the + button.

Setting the required fan speed:

❑ Press the + button.

The fan speed is increased by one step.

❑ Press the – button.

The fan speed is reduced by one step.

Switching the fan OFF:
❑ Press the 0 button.

Or:

❑ Keep pressing the – button until the fan

switches off.

The most effective method of removing
vapours produced during cooking is to:

❑ Switch the ventilator ON

as soon as you begin cooking.

❑ Switch the ventilator OFF

a few minutes after you have finished
cooking.

Fan OFF

Light

ON / OFF

Reduce fan
speed

Fan ON and
increase speed
Intensive setting

Display for fan setting

0

7

Filters and maintenance

2. Clean the grease filter.

3. Re-insert the clean grease filter.

4. Cancel the

#

in the display.

❑ Press the – button.

Grease filters:

Metal filters are used to trap the greasy
element of the vapours that develop
during cooking.

The filter mats are made from non­combustible metal.

 CAUTION

As the filter becomes more and more
saturated with grease, not only does the
risk of it catching fire increase but the
efficiency of the extractor hood can also be
adversely affected.

IMPORTANT

By cleaning the metal grease filters at
appropriate intervals, the possibility of them
catching fire as a result of a build-up of heat
such as occurs when deep-fat frying or
roasting is taking place, is reduced.

Saturation indicator:

#

When the grease filters reach saturation
point, an acoustic signal is sounded for
6 seconds after the fan has switched off,
and an

#

appears in the display. The grease

filters should be cleaned straight away.

Cleaning the metal grease filters:

❑ In normal operation (1 to 2 hours daily),

the metal grease filter must be cleaned
1 x a month.

❑ The filters can be cleaned in a dish-

washer. It is however possible that they
will become slightly discoloured.

❑ The filter must be placed loosely, and

NOT wedged, in the dishwasher.

IMPORTANT:

Metal filters that are saturated with
grease should not be washed together
with other dishes etc.

❑ When cleaning the filters by hand, soak

them in hot soapy water first of all.
Do not use aggressive, acidic or caustic
cleaners.
Then brush the filters clean, rinse them
thoroughly and leave the water to drain off.

Removing and inserting the metal grease
filters:

 WARNING

The halogen bulbs must be
switched off and cool.

1. Rotate the two catches on the grease
filter and remove the grease filter
sideways.

8

Cleaning and care

Isolate the extractor hood by pulling out
the mains plug or switching off the fuse.

NOTE:

Do not clean the extractor hood with
abrasive sponges or with cleaning agents
which contain sand, soda, acid or chlorine!

❑ Clean the extractor hood with a hot soap

solution or a mild window cleaner.

❑ Do not scrape off dried-on dirt but wipe

off with a damp cloth.

❑ When cleaning the grease filters, remove

grease deposits from accessible parts of
the housing. This prevents the risk of fire
and ensures that the extractor hood
continues operating at maximum
efficiency.

Screen and control buttons:

Clean with a mild detergent solution and a
soft, damp cloth only.

Do not use stainless steel cleaners.

Stainless steel surfaces:

❑ Use a mild non-abrasive stainless steel

cleaner.

❑ Clean the surface in the same direction

as it has been ground and polished.

❑ We recommend our stainless steel

cleaner no. 461731.
See enclosed service booklet for order
address.

Aluminium, coated and plastic surfaces:

❑ Do not use dry cloths.
❑ Use a mild window cleaning agent.
❑ Do not use aggressive, acidic or caustic

cleaners.

Observe the warranty regulations in the
enclosed service booklet.

9

If you encounter a problem

If an #appears in the display:

❑ See "Filters and maintenance" Section.

If is not possible to operate the extractor
hood:

❑ Disconnect the extractor hood from the

mains electricity supply by pulling out the
plug or switching it off at the main fuse
box.
Wait for approx. 1 minute and then
switch it on again.

If you have any questions or if a fault
occurs, please call Customer Service.

(See list of Customer Service
representatives).

When you call, please quote the following:

E-Nr. FD

Enter the relevant numbers into the box
above. The E-Nr. (product no.) and FD
(production date) are shown on the
nameplate which can be seen inside the
extractor hood after the filter frame has
been detached.

IMPORTANT:
The manufacturer of the extractor hoods

accepts no liability for complaints which
can be attributed to the design and lay­out of the pipework.

4. Re-insert the bulb ring.

5. Plug the appliance into the mains or

switch it on at the fuse box.

NOTE:

If the light does not function, check that the
bulbs have been inserted correctly.

Replacing the light bulbs

3. Replace the halogen light bulb
(conventional halogen bulb, 12 Volt,
max. 20 Watt, G4 cap).
NOTE: Refer for plug-in lampholder.
Take hold of the bulb with a clean cloth.

1. Switch off the extractor hood and pull
out the mains plug or switch off the
electricity supply at the fuse box.

 CAUTION:

When switched on, the halogen bulbs
become very hot. Even for some time after
the bulbs have been switched off there is
still a risk of burns.

2. Remove the bulb ring with a screwdriver
or similar tool.

10

Important information

Installation Instructions:

Additional information concerning gas
cookers:

When installing gas hotplates, comply with
the relevant national statutory
regulations (e.g. in Germany: Technische
Regeln Gasinstallation TRGI).

Always comply with the currently valid
regulations and installation instructions
supplied by the gas appliance
manufacturer.

Only one side of the extractor hood may be
installed next to a high-sided unit or high
wall. Gap at least 2”.

Minimum distance on gas hotplates
between the upper edge of the trivet
and lower edge of the extractor hood:
30”, Fig. 1.

Old appliances are not worthless
rubbish. Valuable raw materials can be
reclaimed by recycling old appliances.
Before disposing of your old appliance,
render it unusable.

You received your new appliance in a pro­tective shipping carton. All packaging
materials are environmentally friendly and
recyclable. Please contribute to a better
environment by disposing of packaging
materials in an environmentally-friendly
manner.

Please ask your dealer or inquire at your
local authority about current means of
disposal.

The extractor hood can only be used in
exhaust air mode.

Always mount the extractor hood over the
centre of the hob.

Minimum distance between electric hob
and bottom edge of extractor hood:
30”, Fig. 1.

The extractor hood must not be
installed over a solid fuel cooker – a
potential fire hazard (e.g. flying sparks) –
unless the cooker features a closed,
non-removable cover and all national
regulations are observed.

The smaller the gap between the extractor
hood and hotplates, the greater the like­lihood that droplets will form on the under­side of the extractor hood.

11

Prior to installation

Exhaust-air mode

The exhaust air is discharged upwards
through a ventilation shaft or directly
through the outside wall into the open.

 WARNING

Exhaust air should neither be directed into
a smoke or exhaust flue that is currently
used for other purposes, nor into a shaft
that is used for ventilating rooms in which
stoves or fireplaces are also located.

Exhaust air may be discharged in
accordance with official and statutory
regulations only (e.g. national building
regulations).

Local authority regulations must be
observed when discharging air into smoke
or exhaust flues that are not otherwise in
use.

 WARNING

When the extractor hood is operated in
exhaust-air mode simultaneously with a
different burner which also makes use of
the same chimney (such as gas, oil or

coal-fired heaters, continuous-flow heaters,
hot-water boilers) care must be taken to

ensure that there is an adequate supply
of fresh air which will be needed by the

burner for combustion.
Safe operation is possible provided that the

underpressure in the room where the
burner is installed does not exceed 4 Pa
(0.04 mbar).

This can be achieved if combustion air can
flow through non-lockable openings, e.g. in
doors, windows and via the air­intake/exhaust-air wall box or by other
technical measures, such as reciprocal
interlocking, etc.

If the air intake is inadequate, there is a
risk of poisoning from combustion gases
which are drawn back into the room.

An air-intake/exhaust-air wall box by itself
is no guarantee that the limiting value will
not be exceeded.

Note: When assessing the overall
requirement, the combined ventilation
system for the entire household must be
taken into consideration. This rule does not
apply to the use of cooking appliances,
such as hobs and ovens.

If the exhaust air is going to be
discharged into the open, a telescopic

wall box should be fitted into the outside
wall.

12

For optimum extractor hood efficiency:

❑

Short, smooth air exhaust pipe.

❑

As few bends in the pipe as possible.

❑

Diameter of pipe to be as large as
possible and no tight bends in pipe.

If long, rough exhaust-air pipes,
many pipe bends or smaller pipe
diameters are used, the air extraction
rate will no longer be at an optimum
level and there will be an increase in
noise.

IMPORTANT:
The manufacturer of the extractor

hoods accepts no liability for
complaints which can be attributed to
the design and layout of the
pipework.

❑

Round pipes:

We recommend
Internal diameter: 6”.

❑

Flat ducts must have an internal cross­section that equates to that of round
pipes.

There should be no sharp bends.

l 6” approx. 28,3 inches

2

❑

If pipes have different diameters:

Insert sealing strip.

❑

For exhaust-air mode, ensure that
there is an adequate supply of fresh air.

Prior to installation

Connecting a l 6” exhaust-air pipe:

❑

Mount the pipe
directly onto the
air outlet on the
hood.

13

Prior to installation

The extractor hood may be connected to
correctly installed earthed sockets only.
Preferably attach the earthed sockets
directly behind the flue duct.

NOTE:

An additional earthed socket is required for
connecting the screen to the power supply.

❑

The earthed socket should be
connected via its own circuit.

❑

If the earthed socket is no longer
accessible following installation of the
extractor hood, ensure that there is a
permanently installed disconnector.

If it is necessary to wire the extractor
hood directly into the mains:

The extractor hood should only be
connected to the electricity supply by a
properly qualified electrician.

A separator must be installed in the
household circuit. A suitable separator is a
switch that has a contact gap of more than

1

/8” and interrupts all poles. Such devices

include circuit breakers and contactors.

CAUTION:

If the connecting cable for this appliance is
damaged, the cable must be replaced by
the manufacturer or his customer service
or a similarly qualified person in order to
prevent serious injury to the user.

Electrical data:

Are to be found on the name plate inside
the appliance after removal of the filter
frame.

WARNING: Before undertaking any

repairs, always disconnect the extractor
hood from the electricity supply.

Length of the connecting cable: 511/8”.

This extractor hood corresponds to EC
regulations concerning RF interference
suppression.

Electrical connection

 WARNING: THIS APPLIANCE MUST

BE EARTHED
IMPORTANT: Fitting a Different Plug:

The wires in the mains lead are coloured in
accordance with the following code:

Green and Yellow – Earth
Blue – Neutral
Brown – Live

If you fit your own plug, the colours of these
wires may not correspond with the identify­ing marks on the plug terminals.

This is what you have to do:

1. Connect the green and yellow (Earth)
wire to the terminal in the plug marked
‘E’ or with the symbol ( ), or coloured
green or green and yellow.

2. Connect the blue (Neutral) wire to the
terminal in the plug marked ‘N’ or
coloured white.

3. Connect the brown (Live) wire to the
terminal marked ‘L’, or coloured black.

Electrical connection

Preparing the ceiling

❑

The ceiling must be flat and horizontal.

❑

Ensure that the ceiling is capable of pro­viding a firm hold for mounting screws
and plugs. The enclosed plugs are sui­table for concrete and stonework. If the
ceiling is made of any other material,
use appropriate mounting components.

Weight in kg: 40,5.

We reserve the right to construction changes within the
context of technical development.

14

Installation

4. Determine the overall height of the
support frame.

– This is the height of the ceiling, the

height of the base and the distance
between the hob and extractor hood.

The extractor hood is designed to be
fitted to the kitchen ceiling or a rigid
suspended ceiling.

CAUTION:

Ensure that the minimum distance
between hotplate and extractor hood is
30” for electric hotplates and 30” for gas
hotplates.

1. Mark the centre point of the extractor
hood on the ceiling.

2. Using the template, mark screw
positions on the ceiling.

3. Drill 2x

1

/4” ø holes and insert wall plugs

flush with the ceiling.
Note: At least one screw for the

mounting must be installed through a
stud.

15

Installation

08. Insert the extractor hood over the

installation aids on the support frame.

5. Screw together the upper and lower
sections of the support frame at the
specified overall height with 8 screws.

10. Align the extractor hood. To do this,
loosen the ceiling screws in the support
frame.

09. Screw the extractor hood to the support

frame and screw back the panel.

6. Screw the support frame to the ceiling
with 4 screws.

7. Remove the panel.