Bosch CC484, CC488, CC486 Operator's Manual
EN
Operators Manual
Solution Ultima Series
(844/862/880)
CC484/CC486/CC488
CC484/CC486/CC488 | Operators Manual | Notices EN | 2
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Copyright Notice
Unless otherwise indicated, this publication is the
copyright of Bosch Security Systems Pty Ltd
(“Bosch”). All rights are reserved.
You may download a single copy of this publication.
By downloading the publication you agree that you
will: (i) only use the publication for your own
reference; (ii) not commercially exploit or charge any
person for the use of the publication; and (iii) not
modify the publication in any way without the prior
written permission of Bosch.
Except as specified above or where authorised by the
Copyright Act 1968 (Cth), no part of this publication
may be reproduced, transmitted, modified or stored,
in any form or by any means, without the prior
written permission of Bosch.
Notice of Liability
This material is designed for use by tradespeople with
expertise in the installation of this product. Persons
without appropriate expertise should seek assistance
before attempting installation.
While care has been taken in the preparation of this
material, Bosch Security Systems Pty Ltd and its
representatives will not be responsible to any person
or entity for any loss or damage directly or indirectly
caused by information in, or any omission from, this
material.
Bosch Security Systems Pty Ltd reserves the right to
make changes to features and specifications of its
products at any time without prior notification.
New Zealand Telepermit Notes
The grant of a telepermit for a device in no way
indicates Telecom acceptance of responsibility for the
correct operation of that device under all operating
conditions.
This equipment will not be used in any manner that
could constitute a nuisance to other telecom
customers.
Immediately disconnect this equipment should it
become physically damaged and arrange for its
disposal or repair.
The transmit level from this device is set at a fixed
level and because of this, there may be circumstances
where the performance is less than optimal. Before
reporting such occurrences as faults, please check the
line with a standard telepermitted telephone and do
not report a fault if the telephone performance is
satisfactory.
This device is equipped with pulse dialling while the
Telecom standard is DTMF tone dialling. There is no
guarantee that Telecom lines will always continue to
support pulse dialling.
Use of dialling, when this equipment is connected to
the same line as other equipment, may give rise to
bell noise and also cause a false answer condition.
Should such problems occur, the user should not
contact the Telecom Faults Service.
This equipment is set up to carry out test calls at predetermined times. Such test calls can interrupt any
other calls that may be set up on the line at the same
time. The timing set for such test calls should be
discussed with the installer.
The timing set for test calls from this equipment may
be subject to drift. If this proves to be inconvenient
and your calls are interrupted, then the problem of
timing should be discussed with the equipment
installer. The matter should not be reported as a fault
to Telecom Faults Service.
This equipment shall not be set up to make automatic
calls to the Telecom 111 Emergency Service.
This equipment should not be used under any
circumstances that may constitute a nuisance to other
Telecom customers.
In the event of any problem with this device, the
systems battery, AC mains supply, and telephone line
should be disconnected. The user is to arrange with
the supplier of the device to make the necessary
repairs.
Should the matter be reported to Telecom as a wiring
fault and the fault proven to be due to this product, a
call-out charge will be incurred.
CC484/CC486/CC488 | Operators Manual | Table of Contents EN | 3
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Table of Contents
1. Introduction ......................................................5
2. Specifications .................................................... 5
3. Codepad Indicators.......................................... 5
3.1 Zone Indicators.................................................6
3.2 AWAY Indicator..............................................6
3.3 STAY Indicator ................................................6
3.4 System Disarmed..............................................6
3.5 MAINS Indicator .............................................6
3.6 Off Indicator/Zone Sealed .............................. 6
3.7 On Indicator/Zone In Alarm..........................6
3.8 FAULT Indicator ............................................. 7
3.9 Audible Indications..........................................7
3.10 Arming the System...........................................7
3.10.1 Forced Arming ................................................. 7
3.10.2 Arming in AWAY Mode.................................7
3.10.3 Arming in STAY Mode 1................................8
3.10.4 Arming in STAY Mode 2................................8
3.10.5 Programming STAY Mode 2 Zones ..............9
4. Disarming the System......................................9
5. User Codes........................................................9
5.1 Adding User Codes.......................................... 9
5.2 Adding Radio Remote User Codes................9
5.3 Deleting User/Radio Codes............................ 9
6. Radio Transmitter Operations......................10
7. Codepad Alarms ............................................ 10
7.1 Codepad Duress Alarm................................. 10
7.2 Codepad Panic Alarm ...................................10
7.3 Codepad Fire Alarm...................................... 10
7.4 Codepad Medical Alarm...............................10
7.5 Codepad Tamper Alarm (Access Denied) ..11
8. Isolating Zones................................................11
8.1 Standard Isolating ..........................................11
8.2 Code to Isolate ...............................................11
9. Fault Analysis Mode ......................................11
9.1 Fault Descriptions...........................................12
10. Date and Time................................................ 13
11. Turning Outputs On/Off...............................13
12. Reset Latching Outputs .................................13
13. Telco Arm/Disarm Sequence (Call Forward
On/Off) ........................................................... 13
13.1 Telco Arm Sequence......................................13
13.2 Telco Disarm Sequence.................................14
14. Testing ............................................................. 14
14.1 Horn Speaker Test......................................... 14
14.2 Bell Test .......................................................... 14
14.3 Strobe Test...................................................... 14
14.4 Walk Test Mode............................................. 14
14.5 Test Report .....................................................15
15. Event Memory ............................................... 15
16. Day Alarm ...................................................... 15
17. Codepad Buzzer Tone Change .................... 15
18. Remote Arming by Telephone..................... 15
19. Partitioning .....................................................15
19.1 Master Partitioned Codepad Indicators....... 16
19.1.1 Zone Indicators .............................................. 16
19.1.2 Area On/Off Indicators................................. 16
19.1.3 Area Display Indicators................................. 16
19.1.4 Status Indicators 16
19.2 Operation of Codepads in Partitioning .......16
20. Domestic Dialling ..........................................16
20.1 Acknowledging Domestic Calls.................... 16
20.2 Programming Domestic Telephone Numbers17
20.3 Disable Domestic Dialling ............................17
21. Basic Pager Reporting ................................... 17
21.1 Basic Pager Display Information.................. 17
22. Glossary of Terms.......................................... 20
23. Installation Notes ........................................... 22
Figures
Figure 1: CP5 Eight Zone LED Codepad............... 5
Figure 2: CP5 Eight Zone LCD Codepad .............. 5
Figure 3: RF3332 – Two Button RF Keyfob........ 10
Figure 4: RF3334 – Four Button RF Keyfob........ 10
Figure 5: CP5 LED Codepad Showing Audible
Alarm Buttons ......................................... 10
Figure 6: Master Partitioned Codepad.................. 16
Figure 7: Basic Pager Display ................................19
Tables
Table 1: Specifications ............................................. 5
Table 2: Zone Indicators ......................................... 6
Table 3: AWAY Indicator....................................... 6
Table 4: STAY Indicator......................................... 6
Table 5: MAINS Indicator ...................................... 6
Table 6: FAULT Indicator ...................................... 7
Table 7: Audible Indicators ....................................7
Table 8: Arming Methods....................................... 7
Table 9: How to Arm the System in AWAY
Mode .......................................................... 8
CC484/CC486/CC488 | Operators Manual | Table of Contents EN | 4
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Table 10: How to Arm the System in STAY Mode
1 .................................................................. 8
Table 11: Fault Indicators........................................12
Table 12: Telco Arm/Disarm Dialling Digits........ 14
Table 13: Domestic Dialling Telephone Digits.....17
Table 14: Zone Status Display Descriptions.......... 18
Table 15: System Status........................................... 18
Table 16: Glossary of Terms...................................20
CC484/CC486/CC488 | Operators Manual | 1. Introduction EN | 5
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
1. Introduction
Congratulations on selecting the Solution Ultima
Series Control Panel (models
CC484/CC486/CC488) to protect you and your
property. To obtain the most from your unit, take
time to read through this manual and familiarise
yourself with the numerous outstanding operating
features of this system. In all aspects of planning,
engineering, styling, operation, convenience, and
adaptability, we have sought to anticipate your every
possible requirement.
Programming simplicity and speed were some of the
major considerations and we believe that our
objectives in this area were more than satisfied.
This manual explains all aspects of operating the
control panel. All system parameters and options are
detailed; however, suitability is left up to the
individual. Every system can be tailored to meet all
requirements quickly and easily.
2. Specifications
Table 1: Specifications
Temperature Range
0oC to +45 oC
(+32
o
F to +113oF)
Humidity
10% to 95%
Power Source
TF008 Plug Pack –
240 V/18 VAC @ 1.3 A
Stand-By Current
65 mA
Current Draw in
Alarm Condition
115 mA
Current Draw in
Alarm Condition with
Codepad
105 mA
Back-Up Battery
6 Ah/12 VDC Rechargeable
Sealed Lead Acid Battery
Dimensions (Case,
packed in carton)
306 mm x 262 mm x 84 mm
(12.05 in. x 10.31 in. x 3.31 in.)
Weight
2.5 kg
(5.51 lb.)
Supplier Code
N771
New Zealand
Telepermit
Solution Ultima 844 –
PTC 211/98/085
Solution Ultima 862 –
PTC 211/98/084
Solution Ultima 880 –
PTC 211/98/083
Malaysia Approval
Number
Pending
The Austel permit issued for this product
is subject to the following condition:
The Solution Ultima Series Control Panel
may only be powered by a Bosch Security
Systems TF008 plug pack (Approval
Number Q92128).
Test the sirens, strobe, and zones at
weekly intervals. See Section 14. Testing
for further information.
3. Codepad Indicators
Figure 1: CP5 Eight Zone LED Codepad
Figure 2: CP5 Eight Zone LCD Codepad
The codepad is the communications interface
between you and your alarm system. Use the
codepad to issue commands. The codepad offers
both visual and audible indications that guide you
through the general operation.
The codepad incorporates numerous indicators.
There are zone indicators used to show the condition
of each zone. Four other indicators show general
status. The following pages outline a list of situations
and the relevant indicators that are seen.
CC484/CC486/CC488 | Operators Manual | 3. Codepad Indicators EN | 6
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
3.1 Zone Indicators
1 2 3 ….
The zone indicators (1 to 8) display
the status of the zones. Table 2 lists the
various circumstances that the
indicators display (such as Zone
Sealed, Zone Unsealed, and so on).
Table 2: Zone Indicators
Indicator Definition
On Zone is unsealed.
Off Zone is sealed.
Flashing Fast
(0.25 seconds on/
0.25 seconds off)
Zone is in alarm condition.
Flashing Slow
(1 second on/
1 second off)
Zone is manually isolated or
selected to be isolated.
3.2 AWAY Indicator
The AWAY indicator displays that the
system is armed in AWAY Mode. The
AWAY indicator flashes in unison with
the STAY indicator when
programming various options
throughout the Operators Manual.
See Section 3.10.2 Arming in AWAY Mode
for information on the different
methods of arming the system in
AWAY Mode.
Table 3: AWAY Indicator
Indicator Definition
On System is armed in AWAY Mode.
Off System is not armed in AWAY Mode.
3.3 STAY Indicator
The STAY indicator displays that the
system is armed in STAY Mode 1 or
STAY Mode 2. The STAY indicator also
flashes in unison with the AWAY
indicator when programming various
options throughout the Operators Manual.
See Section 3.10.3 Arming in STAY Mode 1
for different methods of arming in STAY
Mode 1. See Section 3.10.4 Arming in
STAY Mode 2 for the method of arming in
STAY Mode 2.
Table 4: STAY Indicator
Indicator Definition
On System is armed in STAY Mode 1
or STAY Mode 2.
Off System is not armed in STAY
Mode 1 or STAY Mode 2.
Flashing
twice a
second
Zone isolating mode or setting
STAY Mode 2 zones.
Flashing once
every
3 seconds
Day alarm status – day alarm
turned on.
3.4 System Disarmed
This indicator displays with the
indicator when the system is disarmed.
3.5 MAINS Indicator
The MAINS indicator displays that the
system’s AC mains supply is normal or
failed.
Table 5: MAINS Indicator
Indicator Definition
On AC mains power normal.
Flashing AC mains supply has failed.
3.6 Off Indicator/Zone Sealed
The
indicator displays when the
system is in the disarmed state and
flashes when a zone becomes unsealed
during the disarmed state. The
indicator stops flashing when all zones
are sealed.
3.7 On Indicator/Zone In Alarm
The
indicator displays when the
system is armed in AWAY Mode and
flashes when an alarm occurs. The
indicator resets once a valid user code
is entered.
CC484/CC486/CC488 | Operators Manual | 3. Codepad Indicators EN | 7
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
3.8 FAULT Indicator
The FAULT indicator displays that the
system detected a system fault. See
Section 9. Fault Analysis Mode for
additional information on system faults.
Every time a new system fault is
detected (such as, FAULT indicator
flashing), the codepad begins to beep
once every minute. Pressing the [#]
button once cancels the once a minute
beep and acknowledges the fault (such
as, FAULT indicator on steady).
Table 6: FAULT Indicator
Indicator Definition
On There is a system fault that
needs to be rectified.
Off The system is normal, there are
no faults.
Flashing There is a system fault that
needs to be acknowledged.
3.9 Audible Indications
Table 7 defines the audible indicators given out by
t
he codepad buzzer.
Table 7: Audible Indicators
Audible
Indicator
Definition
One short beep A button was pressed on the
codepad, or exit time ended
when armed in STAY Mode 1
or STAY Mode 2.
Two short beeps The system accepted your
code.
Three short
beeps
The requested function was
executed.
One long beep Indicates the end of exit time
when armed in AWAY Mode, or
the requested operation was
denied or aborted.
One beep every
second
Walk Test Mode is currently
active or a warning before
automatic arming takes place.
One short beep
every minute
There is a system fault waiting
to be acknowledged.
3.10 Arming the System
There are several ways to arm the system
depending on whether you are:
• Leaving the premises and require all active
zones to be in a ready state for an intruder.
• Remaining in the premises and only require
part of the system to be in a ready state for an
intruder.
If a zone is not sealed at the end of exit time, the
zone is automatically isolated and constantly
displayed on the remote codepad. The zone
becomes an active part of the system when the
zone is restored.
For example, if a window is left open after exit
time expired, the window is not an active part of
the system until the window is closed. Opening
the window after exit time expired causes an
alarm condition.
Table 8 defines the different methods for arming
the system.
Table 8: Arming Methods
Mode Arming Method
AWAY Mode
Arms the entire system. See Section
3.10.2 Arming in AWAY Mode.
STAY Mode 1 Arms all zones except those
programmed to be automatically
isolated by the installer. See Section
3.10.3 Arming in STAY Mode 1.
STAY Mode 2 Arms all zones except those
programmed to be automatically
isolated by the Master Code holder.
See Section 3.10.4 Arming in STAY
Mode 2.
3.10.1 Forced Arming
The feature of arming the system when a zone is
not sealed is known as forced arming. If the
system does not arm and a long beep is heard,
forced arming is not permitted. If this is the case,
you must ensure that all zones are sealed or
manually isolated before you can arm the system.
See Section 8. Isolating Zones.
3.10.2 Arming in AWAY Mode
When you leave your premises and require all
zones to be in a ready state to detect intrusion,
arm the system in AWAY Mode.
There are two different methods for arming the
system in AWAY Mode. Method one is standard
and always operates. Method two is optional and
can be disabled by your installer if you do not
want to use single button arming.
CC484/CC486/CC488 | Operators Manual | 3. Codepad Indicators EN | 8
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Table 9: How to Arm the System in AWAY
Mode
Method
One
Enter your user code followed by
the [#] button (for example,
[2580#]).
Two beeps sound and the AWAY
indicator displays. Exit time starts
counting.
Method
Two
Hold down the [#] button until two
beeps sound.
The AWAY indicator displays and
exit time starts counting.
3.10.3 Arming in STAY Mode 1
STAY Mode 1 is only used when the perimeter
and unused areas of the premises need to be
armed to detect an intruder from entering the
premises. At the same time, you can move freely
within an area that is automatically isolated.
Only your security company can program zones
automatically isolated in STAY Mode 1.
There are two different methods for arming the
system in STAY Mode 1. Method one is standard
and always operates. Method two is optional and
may be disabled by your installer if you do not
want to use single button arming.
Entry Guard Timer for STAY Mode 1
When arming the system in STAY Mode 1, an
optional entry timer called Entry Guard Timer for
STAY Mode 1 is available. Use this entry timer to
delay the sirens if a zone is not automatically
isolated and triggered an alarm condition. Entry
Guard Timer For STAY Mode 1 is the delay time
used for all zones except 24-hour zones when the
system is armed in STAY Mode 1 or STAY Mode
2.
If the Entry Guard Timer for STAY Mode 1 is
programmed and a zone was not automatically
isolated is triggered, the codepad beeps twice a
second until the entry timer expires or the system
is disarmed. If the alarm condition is not reset by
entering your user code followed by the [#] button
(such as, [2580#]) before the entry timer expires,
the sirens activate into alarm. Only your installer
can program this feature.
Table 10: How to Arm the System in STAY
Mode 1
Method One
Enter your user code followed by the [*]
button (for example, [2580*]).
Two beeps sound and the STAY
indicator displays. Exit time starts
counting.
Any zones programmed to be
automatically isolated in STAY Mode 1
flash until exit time expires. At the end of
exit time, all zones selected to be
automatically isolated turn off and the
codepad gives one short beep.
Method Two
Hold down the [*] button until two beeps
sound.
The STAY indicator displays and exit
time starts counting.
Any zones programmed to be
automatically isolated in STAY Mode 1
flash until exit time expires. At the end of
exit time, the zone indicators turn off and
the codepad gives one short beep.
3.10.4 Arming in STAY Mode 2
STAY Mode 2 is only used when the perimeter
and unused areas of the premise need to be armed
to detect an intruder from entering the premise. At
the same time, allowing you to move freely within
an area that is automatically isolated. Any Master
Code user can program zones to be automatically
isolated in STAY Mode 2.
Entry Guard Timer for STAY Mode 2
When arming the system in STAY Mode 2, an
optional entry timer called Entry Guard Timer for
STAY Mode 2 is available. Use this entry timer to
delay the sirens if a zone is not automatically
isolated and triggered into alarm condition. Entry
Guard Timer for STAY Mode 2 is the delay time
used for all zones except 24-hour zones when the
system is armed in STAY Mode 1 or STAY Mode
2.
If the Entry Guard Timer for STAY Mode 2 is
programmed and a zone that was not
automatically isolated triggers, the codepad beeps
twice a second until the entry timer expires or the
system is disarmed. If the alarm condition is not
reset by entering your user code followed by the
[#] button (for example, [2580#]) before the entry
timer expires, the sirens activate into alarm. Only
your installer can program this option.
CC484/CC486/CC488 | Operators Manual | 4. Disarming the System EN | 9
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
How to Arm the System in STAY Mode 2
Hold down the [0] button until two beeps sound.
The STAY indicator displays and exit time starts
counting.
Any zones programmed to be automatically
isolated in STAY Mode 2 flash until exit time
expires. At the end of exit time, all zones selected
to be automatically isolated extinguish and the
codepad emits one short beep.
3.10.5 Programming STAY Mode 2 Zones
Programming zones to be automatically isolated in
STAY Mode 2 are only carried out if you have a
Master Code.
How to Program STAY Mode 2 Zones
1. Enter your four character Master Code,
followed by [4] and the [#] button (for
example, [25804#]). Three beeps sound and
the STAY indicator flashes.
2. Enter the zone number to be automatically
isolated, followed by the [*] button (for
example, [1*] = Zone 1, [2*] = Zone 2).
The selected zone flashes. If you make a
mistake, enter the same zone number followed
by the [#] button to clear the incorrect zone.
To select additional zones to be automatically
isolated in STAY Mode 2, repeat Step 2 as
many times as required.
3. Press the [#] button to exit this mode when
you finish selecting all zones to be
automatically isolated in STAY Mode 2. Two
beeps sound and the STAY and AWAY
indicators turn off.
4. Disarming the System
When you enter the premises after the system is
armed in AWAY mode, or if you armed the
system in STAY Mode 1 or STAY Mode 2, you
must disarm the system to disable detection
devices that activate an alarm.
If there was an alarm condition prior to disarming
the system, a flashing zone indicator displays,
indicating a previous alarm on that zone.
How to Disarm the System
Enter your user code followed by the [#] button
(for example, [2580#]). Two beeps sound.
5. User Codes
5.1 Adding User Codes
Only the Master Code holder can add or change
other system user codes, including the Master
Code. Up to eight user codes can be programmed
to operate the system.
How to Add a User Code
1. Enter your four character Master Code,
followed by [1] and the [#] button (for
example, [25801#]).
Three beeps are heard and the STAY and
AWAY indicators flash.
2. Enter the User Code number (1 to 8),
followed by the [#] button (for example, [2#]
= User 2, [8#] = User 8). Two beeps are heard
and the selected user number displays on the
codepad indicators.
3. Enter the digits required for the new code
followed by the [#] button (for example, for
User Code 5768, enter [5768#]). Two beeps
are heard and the STAY and AWAY
indicators turn off.
To add or change other User Codes, repeat
this procedure as many times as required.
5.2 Adding Radio Remote User
Codes
Only the Master Code holder can add or change
other system user codes. Up to eight radio user
codes (User Codes 9 to 16) can be programmed to
operate the system.
How to Add a Radio Remote User Code
1. Enter your four character Master Code,
followed by [1] and the [#] button (for
example, [25801#]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the radio remote user code number (9 to
16), followed by the [#] button (for example,
[9#] = User 9, [16#] = User 16). Two beeps
are heard and the selected user number
displays on the codepad indicators.
3. Enter the nine digit ID number found on the
back of the radio remote hand held
transmitter, followed by the [#] button. Two
beeps are heard and the STAY and AWAY
indicators extinguish.
To add or change other radio remote user
codes, repeat this procedure as many times as
required.
5.3 Deleting User/Radio Codes
Only the Master Code holder can delete other
system user codes.
How to Delete a User Code
1. Enter your four character Master Code,
followed by [1] and the [#] button (for
example, [25801#]).
Three beeps sound and the STAY and AWAY
indicators flash.
Loading...