Bosch C900V2 Specsheet

Intrusion Alarm Systems | Conettix C900V2 Dialer Capture Ethernet Module

Conettix C900V2 Dialer Capture Ethernet Module

www.boschsecurity.com

u Captures alarm and event data from dialer-based

control panels using CONTACT ID, SIA, Modem II, Modem IIe, Modem IIIa2, Pulse, and other formats

The Conettix C900V2 Dialer Capture Ethernet Module works with most control panels using a standard digital dialer format and provides end-to-end security. The module links the digital dialer to the Public Switched Telephone Network (PSTN), the digital dialer’s telephone interface, and an Ethernet network. With the Ethernet link, the C900V2 can:

• Communicate with the control panel dialer

• Decode and deliver signals to a Conettix D6600 Communications Receiver/Gateway

• Relay a confirmation message back to the control panel dialer

Whether a control panel dials through a telephone line or through the C900V2, the data remains the same. The C900V2 empowers digital dialer control panels to work over an IP network such as a Local Area Network (LAN), a Wide Area Network (WAN), or the Internet.

u Performs full data transmissions without changing

the data

u 12 VDC to 24 VDC voltage range

u Re-routes signals using UDP/IP-based data networks

u Convenient connection (RJ-45 Jack) to Ethernet

networks

The C900V2 decodes and converts the transmitted dialer message to data for transport over any UDP/IP network. After the Conettix D6600 Communications Receiver/ Gateway receives a message or event, it sends an acknowledgement message to the C900V2. The C900V2 returns an appropriate response to the dialer, maintaining end-to-end acknowledgment. The C900V2 operates in Intercept Mode, connecting the dialer to the network under normal circumstances. If the C900V2 loses contact with the Conettix D6600 Communications Receiver/Gateway, the unit goes into Fallback Mode, connecting the dialer to the PSTN telephone line.

System overview

When the dialer has a message to report, the C900V2 simulates dial tone and line voltages, causing the dialer to behave as though it is connected to a monitoring center digital receiver through the PSTN.

O F F

PANEL

TELCO

OUT4

OUT1

OUT2

OUT3

IN3

IN2

IN1

I-12V+

2.1

| Conettix C900V2 Dialer Capture Ethernet Module

SIA Bell 103, 110/300 baud

Robofon

Telim

Inputs

Input Description

1 Used as an end-of-line (EOL) supervised loop. Detects open,

short, and normal states. Terminate this input with a 10 kΩ EOL resistor.

2 Used for intercept inhibit to force the C900V2 into Fallback

mode for at least two minutes.

3 Used for intercept override, allowing users to switch between

intercept and fallback modes.

Outputs

OutputDescription

1. Control Panel

2. Dialer Connection

2.1 Dialer Output to RJ-31x Jack and PSTN

3. Conettix C900V2 Dialer Capture Ethernet Module

4. Ethernet or LAN Connection

5. LAN, WAN, or the Internet

6. Connection To Ethernet Network Interface Card (NIC)

7. Host PC with Conettix D6200 Programming/Administration Software

8. Conettix D6680 Ethernet Network Adapter

9. Com 1 (Optional)

10.Com 4

1 Provides local annunciation if the power to the C900V2 is lost

or the CPU fails.

2 Provides local annunciation if the connection to the

monitoring center is lost.

3 Provides local annunciation whenever the C900V2 is in

intercept mode.

4 Controllable from the monitoring center and the Conettix

D6200 Programming/Administration Software (default is open).

Intercept and Fallback Modes

• Intercept Mode: The C900V2 connects the dialer to the network. Intercept mode remains on as long as the C900V2 remains in continuous contact with the Conettix D6600 Communications Receiver/Gateway.

• Fallback Mode: The C900V2 connects the dialer to the telephone line, removing itself from the telephone circuit. Fallback mode occurs if the C900V2 loses

11.Conettix D6600 Communications Receiver/Gateway

contact with the Conettix D6600 Communications Receiver/Gateway, loses power, or stops operating correctly.

Functions

Communication Formats

ADT-SIA

BFSK (2300Hz ACK Tone or 1400Hz ACK Tone)

DTMF (Contact ID, High Speed and 4/2 Express)

FBI Superfast DTMF (1400 Hz ACK Tone or 2300 Hz ACK Tone)

Pulse 3/1, 3/1 Checksum, 4/2 (1400 Hz ACK Tone or 2300 Hz ACK Tone)

Radionics Modem II, Radionics Modem IIe , and Modem IIIa

Seriee FSK and DTMF

LED Indicators

The C900V2 has two dual-colored LEDs that indicate the module's status (the SYSTEM LED and the DIALER LED).

Modular Jacks

The C900V2 module has three modular jacks.

• Panel Jack: Connects to a dialer through a modular telephone cord (D162).

• TELCO Jack: Connects to a PSTN line through a modular telephone cord (D162).

• Ethernet Jack: Connects to the Ethernet data network through an Ethernet cable. For 10BASE-T, the cable must be Category 3 or better. For 100BASE-T, the cable must be Category 5 or better.

SIA V.21, 110/300 baud

+ 2 hidden pages